Biosensors based on vertically interrogated optofluidic sensing cells

El objetivo de la presente tesis doctoral es el desarrollo de un nuevo concepto de biosensor óptico sin marcado, basado en una combinación de técnicas de caracterización óptica de interrogación vertical y estructuras sub-micrométricas fabricadas sobre chips de silicio. Las características más importantes de dicho dispositivo son su simplicidad, tanto desde el punto de vista de medida óptica como de introducción de las muestras a medir en el área sensible, aspectos que suelen ser críticos en la mayoría de sensores encontrados en la literatura. Cada uno de los aspectos relacionados con el diseño de un biosensor, que son fundamentalmente cuatro (diseño fotónico, caracterización óptica, fabricación y fluídica/inmovilización química) son desarrollados en detalle en los capítulos correspondientes. En la primera parte de la tesis se hace una introducción al concepto de biosensor, en qué consiste, qué tipos hay y cuáles son los parámetros más comunes usados para cuantificar su comportamiento. Posteriormente se realiza un análisis del estado del arte en la materia, enfocado en particular en el área de biosensores ópticos sin marcado. Se introducen también cuáles son las reacciones bioquímicas a estudiar (inmunoensayos). En la segunda parte se describe en primer lugar cuáles son las técnicas ópticas empleadas en la caracterización: Reflectometría, Elipsometría y Espectrometría; además de los motivos que han llevado a su empleo. Posteriormente se introducen diversos diseños de las denominadas "celdas optofluídicas", que son los dispositivos en los que se va a producir la interacción bioquímica. Se presentan cuatro dispositivos diferentes, y junto con ellos, se proponen diversos métodos de cálculo teórico de la respuesta óptica esperada. Posteriormente se procede al cálculo de la sensibilidad esperada para cada una de las celdas, así como al análisis de los procesos de fabricación de cada una de ellas y su comportamiento fluídico. Una vez analizados todos los aspectos críticos del comportamiento del biosensor, se puede realizar un proceso de optimización de su diseño. Esto se realiza usando un modelo de cálculo simplificado (modelo 1.5-D) que permite la obtención de parámetros como la sensibilidad y el límite de detección de un gran número de dispositivos en un tiempo relativamente reducido. Para este proceso se escogen dos de las celdas optofluídicas propuestas. En la parte final de la tesis se muestran los resultados experimentales obtenidos. En primer lugar, se caracteriza una celda basada en agujeros sub-micrométricos como sensor de índice de refracción, usando para ello diferentes líquidos orgánicos; dichos resultados experimentales presentan una buena correlación con los cálculos teóricos previos, lo que permite validar el modelo conceptual presentado. Finalmente, se realiza un inmunoensayo químico sobre otra de las celdas propuestas (pilares nanométricos de polímero SU-8). Para ello se utiliza el inmunoensayo de albumina de suero bovino (BSA) y su anticuerpo (antiBSA). Se detalla el proceso de obtención de la celda, la funcionalización de la superficie con los bioreceptores (en este caso, BSA) y el proceso de biorreconocimiento. Este proceso permite dar una primera estimación de cuál es el límite de detección esperable para este tipo de sensores en un inmunoensayo estándar. En este caso, se alcanza un valor de 2.3 ng/mL, que es competitivo comparado con otros ensayos similares encontrados en la literatura. La principal conclusión de la tesis es que esta tipología de dispositivos puede ser usada como inmunosensor, y presenta ciertas ventajas respecto a los actualmente existentes. Estas ventajas vienen asociadas, de nuevo, a su simplicidad, tanto a la hora de medir ópticamente, como dentro del proceso de introducción de los bioanalitos en el área sensora (depositando simplemente una gota sobre la micro-nano-estructura). Los cálculos teorícos realizados en los procesos de optimización sugieren a su vez que el comportamiento del sensor, medido en magnitudes como límite de detección biológico puede ser ampliamente mejorado con una mayor compactación de pilares, alcanzandose un valor mínimo de 0.59 ng/mL). The objective of this thesis is to develop a new concept of optical label-free biosensor, based on a combination of vertical interrogation optical techniques and submicron structures fabricated over silicon chips. The most important features of this device are its simplicity, both from the point of view of optical measurement and regarding to the introduction of samples to be measured in the sensing area, which are often critical aspects in the majority of sensors found in the literature. Each of the aspects related to the design of biosensors, which are basically four (photonic design, optical characterization, fabrication and fluid / chemical immobilization) are developed in detail in the relevant chapters. The first part of the thesis consists of an introduction to the concept of biosensor: which elements consists of, existing types and the most common parameters used to quantify its behavior. Subsequently, an analysis of the state of the art in this area is presented, focusing in particular in the area of label free optical biosensors. What are also introduced to study biochemical reactions (immunoassays). The second part describes firstly the optical techniques used in the characterization: reflectometry, ellipsometry and spectrometry; in addition to the reasons that have led to their use. Subsequently several examples of the so-called "optofluidic cells" are introduced, which are the devices where the biochemical interactions take place. Four different devices are presented, and their optical response is calculated by using various methods. Then is exposed the calculation of the expected sensitivity for each of the cells, and the analysis of their fabrication processes and fluidic behavior at the sub-micrometric range. After analyzing all the critical aspects of the biosensor, it can be performed a process of optimization of a particular design. This is done using a simplified calculation model (1.5-D model calculation) that allows obtaining parameters such as sensitivity and the detection limit of a large number of devices in a relatively reduced time. For this process are chosen two different optofluidic cells, from the four previously proposed. The final part of the thesis is the exposition of the obtained experimental results. Firstly, a cell based sub-micrometric holes is characterized as refractive index sensor using different organic fluids, and such experimental results show a good correlation with previous theoretical calculations, allowing to validate the conceptual model presented. Finally, an immunoassay is performed on another typology of cell (SU-8 polymer pillars). This immunoassay uses bovine serum albumin (BSA) and its antibody (antiBSA). The processes for obtaining the cell surface functionalization with the bioreceptors (in this case, BSA) and the biorecognition (antiBSA) are detailed. This immunoassay can give a first estimation of which are the expected limit of detection values for this typology of sensors in a standard immunoassay. In this case, it reaches a value of 2.3 ng/mL, which is competitive with other similar assays found in the literature. The main conclusion of the thesis is that this type of device can be used as immunosensor, and has certain advantages over the existing ones. These advantages are associated again with its simplicity, by the simpler coupling of light and in the process of introduction of bioanalytes into the sensing areas (by depositing a droplet over the micro-nano-structure). Theoretical calculations made in optimizing processes suggest that the sensor Limit of detection can be greatly improved with higher compacting of the lattice of pillars, reaching a minimum value of 0.59 ng/mL).

Sound of lasers (SOL) - An audiovisual approach to semiconductor laser dynamics

We present an educational software addressed to the students of optical communication courses, for a simple visualization of the basic dynamic processes of semiconductor lasers. The graphic interface allows the user to choose the laser and the modulation parameters and it plots the laser power output and instantaneous frequency versus time. Additionally, the optical frequency variations are numerically shifted into the audible frequency range in order to produce a sound wave from the computer loudspeakers. Using the proposed software, the student can simultaneously see and hear how the laser intensity and frequency change, depending on the modulation and device parameters.

Factores anatómicos, dendrométricos y climáticos implicados en la producción de resina de Pinus pinaster AIT. : aplicación a la mejora de los métodos de resinación

Pinus pinaster Ait. es la conífera con mayor área de distribución en la Península Ibérica y es, a día de hoy, la única especie resinada en nuestro país. La inducción del flujo de resina al exterior para su recolección a través de distintos tipos de heridas ha sido practicada desde hace miles de años por distintas culturas. En todos los casos, las técnicas desarrolladas se basan en la estimulación del característico sistema de defensa de las pináceas. En los últimos siete años se viene observando una tendencia de incremento sustancial de la superficie resinada en España, acompañada por avances tecnológicos dirigidos a la mecanización y mejora de estimulantes. El aprovechamiento resinero se perfila como un sector estratégico en la generación de empleo rural y la conservación de ecosistemas. La industria resinera demanda métodos de extracción más eficaces, una selvicultura adecuada y actualizada, y condiciones laborales de los resineros más dignas con objeto de llegar a ser competitiva en el mercado internacional. Este trabajo se centra en ampliar el conocimiento sobre el sistema de defensa de P. pinaster, concretamente sobre las estructuras y procesos que pueden afectar a la producción de resina. Se analizan las relaciones entre las características anatómicas del xilema, destacando las relacionadas con los canales resiníferos, las variables dendrométricas y dasométricas de la masa y el flujo de resina (objetivo 1). Se estudia cómo estas relaciones son moduladas por las heridas de resinación dependiendo de la técnica de resinación aplicada (objetivo 2), el clima y el balance hídrico del suelo (objetivo 3). El material vegetal, las muestras de suelo y los datos de producción de resina y climáticos usados en esta tesis han sido recogidos en tres montes de utilidad pública; MUP 101 en Armuña, MUP 108 en Melque de Cercos y MUP 117 en Nieva (en esta última solo se recogieron los datos de producciones), todos ellos pinares monoespecíficos de P. pinaster localizados en la denominada Tierra de Pinares Segoviana. En los árboles de nuestro estudio se han aplicado cuatro métodos de resinación: método de pica de corteza con estimulante y método mecanizado con estimulante, ambos en sentido ascendente y descendente. En los trabajos realizados para el análisis de la influencia de la anatomía constitutiva en la producción de resina (objetivo 1) y el efecto del clima (objetivo 3), se obtuvieron muestras del xilema de 26 árboles resinados en Melque de Cercos y Armuña y 12 árboles control sin resinar. Para caracterizar los pies estudiados, se midió la altura, diámetro normal y porcentaje de copa viva. Las muestras de tejido fueron recogidas en una zona del tronco a una distancia del límite de la herida considerada en la bibliografía como no afectada (anatomía constitutiva). Para el análisis de las alteraciones anatómicas inducidas por la herida (objetivo 2), se recogieron muestras en ocho de los individuos en los que se habían realizado los distintos métodos de resinación descritos y en cinco árboles control. Se obtuvieron ocho muestras de tejido distribuidas en la parte superior, inferior, lateral y centro de la herida de cada uno de los árboles resinados. Para establecer las diferencias en la producción de resina según el método de resinación, se analizaron las producciones de 561 árboles resinados en 2012 con estos cuatro métodos en Nieva. Los principales resultados de estos trabajos muestran que la producción de resina está ligada al volumen de canales (axiales y radiales) y a la frecuencia de canales radiales existentes en el árbol antes de efectuar ninguna herida (sistema constitutivo). De esta manera, los árboles grandes productores de resina mostraron una red de canales más densa que aquellos con producciones medias. Una vez realizada la herida de resinación, observamos una disminución del ancho del anillo de crecimiento y del tamaño medio de los canales axiales a la vez que se incrementaba la frecuencia y área ocupada por mm2 de anillo de estos canales. Estos cambios perduraron en el árbol durante al menos tres años y fueron distintos dependiendo de la localización en el entorno de la herida y del método de resinación. Las respuestas más intensas a la herida se observaron el año siguiente a la realización de la misma, en dirección axial, para las distancias más próximas al límite de la herida y para los métodos de resinación en sentido ascendente. Además, se ha constatado que como consecuencia de las heridas de resinación se produjeron cambios en la anatomía del xilema en zonas alejadas de la herida, tanto en el año de la herida como años posteriores. Es decir, se observó una respuesta sistémica del árbol. Respecto al papel del clima como regulador de la respuesta del árbol, se ha evidenciado que la temperatura, la radiación y la ETP influyeron en la producción de resina, no solo durante la campaña de resinación, sino también durante los meses anteriores. El déficit hídrico favoreció la producción y la formación de canales axiales pero, a partir de un determinado umbral, esa relación se invirtió y las lluvias estivales incrementaron la producción. Algunas de estas variables climáticas se asociaron a cambios en el tamaño y frecuencia de las estructuras secretoras, las cuales posiblemente modulan la respuesta defensiva de la planta. La dendrometría del árbol (evaluada a través del diámetro normal, altura y porcentaje de copa viva), la densidad de la masa y el tipo de suelo influyeron en el potencial de producción de resina de P. pinaster. Árboles más vigorosos, parcelas con menores densidades y suelos con más capacidad para la retención de agua y nutrientes presentaron producciones mayores. Estos trabajos se complementan en anexos con una caracterización del sistema socio-ecológico del pinar en resinación. En ese trabajo se identifican sus potenciales servicios ecosistémicos y se evalúa su grado de vinculación con el aprovechamiento resinero con objeto de valorar su funcionalidad y aproximar una valoración económica de modo que sea posible apreciar la importancia económica de los mismos. Para concluir, podemos resaltar que son necesarios más trabajos de carácter científico para avanzar en la comprensión de los procesos anatómicos y fisiológicos que regulan la secreción de resina en P. pinaster y sus interacciones con el medio. Esto permitiría avances certeros hacia el desarrollo de métodos de extracción más eficaces, una selvicultura óptima, el reconocimiento de los beneficios socio-ecológicos y económicos del aprovechamiento y, de manera general, una bibliografía amplia y fiable para la consulta y desarrollo de futuras mejoras que posibiliten la reactivación y conservación de la resinación como aprovechamiento rentable. ABSTRACT Pinus pinaster Ait. is the most widespread conifer in Spain and is now the only species tapped for its oleoresin. External induction of resin secretion, based on the defense system of Pinus trees, has been performed by humans since Classical times through various methods. The socio-economic implication of this practice in Spain justifies a new approach to improve tapping methodology and understand the effects of this activity on the tree. In the last five years, sharp increases in the price of natural resins, accompanied by technological advances directed toward mechanization, have made resin tapping a strategic activity for rural development and forest conservation. The resin industry demands more efficient tapping methods and forest management plans as a way to increase competitiveness in a global market. In this way, this work focuses on the study of the defense system of P. pinaster, with the aim to understand the effects of anatomical and physiological characteristics and environmental conditions on resin yield. The relationships between anatomical variables -with special focus on resin canals-, dendrometric and dasometric variables, and resin yield will be evaluated (objective 1). The tapping wound effects (objective 2) and the intra- and inter-annual variability of climate conditions and soil water availability influence (objective 3) on resin yield will be also studied. The plant and soil material and the resin yield and climatic data used in this thesis have been collected in stands of three public forests of P. pinaster; Armuña, Melque de Cercos and Nieva, located in Segovia (Central Spain). Trees were tapped using two different methods: mechanized or traditional tool, in both upwards and downwards direction. Twenty-six tapped trees of contrasting resin yield classes and twelve non-tapped (control) trees, growing in two locations (Armuña y Melque de Cercos) with the same climate but different stand density and soil characteristics, were selected for studying the role of tree size, xylem anatomy at distal parts aside from the tapping wound (objective 1) and climate influence (objective 3) on resin yield. Concerning the tree defenses induced by the tapping wound (objective 2), the xylem of eight trees, tapped with the two described methods in both upwards and downwards direction, were analyzed. From each tapped tree, eight cores were collected at different locations and varying distances from the tapping wound. In each core, a histological analysis was made. Growth ring width, earlywood and latewood width, and axial canal frequency, area, mean size and location were measured. The effect of the tapping method on resin yield was assessed in 561 P. pinaster tapped trees in a stand in Nieva. In tissues not affected by the tapping wound, the frequency of radial resin canals and the total volume of resin canals were related to resin yield. The frequency of radial canals and the resin yield were strongly related to tree diameter and percentage of live crown. High area of axial resin canals per mm2 was related to high yielding trees, but only in the location with higher plant density and poorer soil quality. In tapped trees, an increase in axial canal frequency and area was found during the three years following the start of tapping activity, suggesting that canal formation is a systemic induced response to wounding. The highest mean annual resin yield was found using the traditional tool in upwards direction, which also induced the highest increase in axial canal frequency and area. The lowest yield was found for mechanized tapping, which showed no differences between the upwards and downwards directions. The strongest induction of systemic induced responses in terms of resin canal frequency and area was detected one year after tapping for upwards tapping. This suggests the involvement of signaling processes that spread mainly upwards, and the importance of adaptive processes as a defense against periodic insect attacks. Intra-annual variation in resin yield was strongly correlated with temperature, solar radiation, potential evapotranspiration and soil water deficit. Inter-annual variation in resin yield and resin canal abundance were correlated with temperature and water deficit in spring, but above a certain threshold of cumulated water deficit in summer rainfall favored resin yield. Under adverse climate scenarios where resource optimization is desirable, a reduced tapping season during the warmest months (June–September) would be advisable, assuming a very small production loss relative to traditional tapping season. Similarly, in years with a rainy summer and/or dry spring, a slightly longer tapping season could be suggested, as resin yield increases after these events. Tree diameter and percentage of live crown, and radial resin canal frequency could be useful criteria for estimating resin yields in P. pinaster. Vigorous trees in lower density stands and growing up in good quality soils will be the most productive. These conclusions could be applied to improve tapping management and breeding programs. These works are complemented with socio-ecological characterization, the identification of the main ecosystem services and an assessment of the possible economic impact derived from the tapping practice. To conclude, more scientific studies are necessary for understanding the anatomical and physiological processes behind resin synthesis and their interactions with the environment. This would afford further progresses towards an extensive and reliable bibliography and improved tapping methods and optimal selvicultural guide lines.

Homodyne measurement of the average photon number

We describe a scheme for measurement of the mean photon flux at an arbitrary optical sideband frequency using homodyne detection. Experimental implementation of the technique requires an acousto-optic modulator in addition to the homodyne detector, and does not require phase locking. The technique exhibits polarization and frequency and spatial mode selectivity, as well as much improved speed, resolution, and dynamic range when compared to linear photodetectors and avalanche photodiodes, with potential application to quantum-state tomography and information encoding using an optical frequency basis. Experimental data also support a quantum-mechanical description of vacuum noise.

Writing and characterisation methods for UV-photosensitivity based devices and their applications

The underlying work to this thesis focused on the exploitation and investigation of photosensitivity mechanisms in optical fibres and planar waveguides for the fabrication of advanced integrated optical devices for telecoms and sensing applications. One major scope is the improvement of grating fabrication specifications by introducing new writing techniques and the use of advanced characterisation methods for grating testing. For the first time the polarisation control method for advanced grating fabrication has successfully been converted to apodised planar waveguide fabrication and the development of a holographic method for the inscription of chirped gratings at arbitrary wavelength is presented. The latter resulted in the fabrication of gratings for pulse-width suppression and wavelength selection in diode lasers. In co-operation with research partners a number of samples were tested using optical frequency domain and optical low coherence reflectometry for a better insight into the limitations of grating writing techniques. Using a variety of different fabrication methods, custom apodised and chirped fibre Bragg gratings were written for the use as filter elements for multiplexer-demultiplexer devices, as well as for short pulse generation and wavelength selection in telecommunication transmission systems. Long period grating based devices in standard, speciality and tapered fibres are presented, showing great potential for multi-parameter sensing. One particular scope is the development of vectorial curvature and refractive index sensors with potential for medical, chemical and biological sensing. In addition the design of an optically tunable Mach-Zehnder based multiwavelength filter is introduced. The discovery of a Type IA grating type through overexposure of hydrogen loaded standard and Boron-Germanium co-doped fibres strengthened the assumption of UV-photosensitivity being a highly non-linear process. Gratings of this type show a significantly lower thermal sensitivity compared to standard gratings, which makes them useful for sensing applications. An Oxford Lasers copper-vapour laser operating at 255 nm in pulsed mode was used for their inscription, in contrast to previous work using CW-Argon-Ion lasers and contributing to differences in the processes of the photorefractive index change

Effect of oscillatory flow on nucleation kinetics of butyl paraben

More than 165 induction times of butyl paraben-ethanol solution in a batch moving fluid oscillation baffled crystallizer with various amplitudes (1-9 mm) and frequencies (1.0-9.0 Hz) have been determined to study the effect of COBR operating conditions on nucleation. The induction time decreases with increasing amplitude and frequency at power density below about 500 W/m3; however, a further increase of the frequency and amplitude leads to an increase of the induction time. The interfacial energies and pre-exponential factors in both homogeneous and heterogeneous nucleation are determined by classical nucleation theory at oscillatory frequency 2.0 Hz and amplitudes of 3 or 5 mm both with and without net flow. To capture the shear rate conditions in oscillatory flow crystallizers, a large eddy simulation approach in a computational fluid dynamics framework is applied. Under ideal conditions the shear rate distribution shows spatial and temporal periodicity and radial symmetry. The spatial distributions of the shear rate indicate an increase of average and maximum values of the shear rate with increasing amplitude and frequency. In continuous operation, net flow enhances the shear rate at most time points, promoting nucleation. The mechanism of the shear rate influence on nucleation is discussed.

WDM orthogonal subcarrier multiplexing

Electro-optical transceivers can be implemented employing all-analog signal processing in order to achieve low values of power consumption and latency. This paper shows that the spectral efficiency of such solutions can be increased by combining orthogonal multicarrier techniques and off-the-shelf microwave components. A real-time 108-Gbit/s experiment was performed emulating a wavelength division multiplexing (WDM) system composed of five optical channels. The optical carriers were provided by an externally injected gain switched optical frequency comb. Each optical channel transmitted a 21.6-Gbit/s orthogonal subcarrier multiplexing (SCM) signal that was modulated and demodulated in the electrical domain without the requirement for digital signal processing. The net data rate remained higher than 100 Gbit/s after taking into account forward error correction overheads. The use of orthogonally overlapping subchannels achieves an unprecedented spectral efficiency in all-analog real-time broadband WDM/SCM links.

Multistabilities and symmetry-broken one-color and two-color states in closely coupled single-mode lasers

We theoretically investigate the dynamics of two mutually coupled, identical single-mode semi-conductor lasers. For small separation and large coupling between the lasers, symmetry-broken one-color states are shown to be stable. In this case the light outputs of the lasers have significantly different intensities while at the same time the lasers are locked to a single common frequency. For intermediate coupling we observe stable symmetry-broken two-color states, where both lasers lase simultaneously at two optical frequencies which are separated by up to 150 GHz. Using a five-dimensional model, we identify the bifurcation structure which is responsible for the appearance of symmetric and symmetry-broken one-color and two-color states. Several of these states give rise to multistabilities and therefore allow for the design of all-optical memory elements on the basis of two coupled single-mode lasers. The switching performance of selected designs of optical memory elements is studied numerically.

Testicular volume and reproductive status of Wild Callithrix jacchus

ARAÚJO, Arrilton ; SOUSA, Maria Bernardete Cordeiro . Testicular volume and reproductive status of Wild Callithrix jacchus. International Journal of Primatology, v.29, p.1355–1364, 2008. DOI 10.1007/s10764-008-9291-4

Food for Pollinators: Quantifying the Nectar and Pollen Resources of Urban Flower Meadows

Planted meadows are increasingly used to improve the biodiversity and aesthetic amenity value of urban areas. Although many ‘pollinator-friendly’ seed mixes are available, the floral resources these provide to flower-visiting insects, and how these change through time, are largely unknown. Such data are necessary to compare the resources provided by alternative meadow seed mixes to each other and to other flowering habitats. We used quantitative surveys of over 2 million flowers to estimate the nectar and pollen resources offered by two exemplar commercial seed mixes (one annual, one perennial) and associated weeds grown as 300m2 meadows across four UK cities, sampled at six time points between May and September 2013. Nectar sugar and pollen rewards per flower varied widely across 65 species surveyed, with native British weed species (including dandelion, Taraxacum agg.) contributing the top five nectar producers and two of the top ten pollen producers. Seed mix species yielding the highest rewards per flower included Leontodon hispidus, Centaurea cyanus and C. nigra for nectar, and Papaver rhoeas, Eschscholzia californica and Malva moschata for pollen. Perennial meadows produced up to 20x more nectar and up to 6x more pollen than annual meadows, which in turn produced far more than amenity grassland controls. Perennial meadows produced resources earlier in the year than annual meadows, but both seed mixes delivered very low resource levels early in the year and these were provided almost entirely by native weeds. Pollen volume per flower is well predicted statistically by floral morphology, and nectar sugar mass and pollen volume per unit area are correlated with flower counts, raising the possibility that resource levels can be estimated for species or habitats where they cannot be measured directly. Our approach does not incorporate resource quality information (for example, pollen protein or essential amino acid content), but can easily do so when suitable data exist. Our approach should inform the design of new seed mixes to ensure continuity in floral resource availability throughout the year, and to identify suitable species to fill resource gaps in established mixes.

Testicular volume and reproductive status of Wild Callithrix jacchus

ARAÚJO, Arrilton ; SOUSA, Maria Bernardete Cordeiro . Testicular volume and reproductive status of Wild Callithrix jacchus. International Journal of Primatology, v.29, p.1355–1364, 2008. DOI 10.1007/s10764-008-9291-4

Adsorção de cobre e cromo utilizando fibra de sisal visando o tratamento da água produzida pela indústria petrolífera

Currently, the oil industry is the biggest cause of environmental pollution. The objective was to reduce the concentration of copper and chromium in the water produced by the oil industry. It was used as adsorbent natural sisal fiber Agave sp treated with nitric acid and sodium hydroxide. All vegetable fibers have physical and morphological properties that enablies the adsorption of pollutants. The basic composition of sisal is cellulose, hemicellulose and lignin. The features are typically found in the characterization of vegetable fibers, except the surface area that was practically zero. In the first stage of adsorption, it was evaluated the effect of temperature and time skeeking to optimize the execution of the factorial design. The results showed that the most feasible fiber was the one treated with acid in five hours (30°C). The second phase was a factorial design, using acid and five hours, this time was it determined in the first phase. The tests were conducted following the experimental design and the results were analyzed by statistical methods in order to optimize the main parameters that influence the process: pH, concentration (mol / L) and fiber mass/ metal solution volume. The volume / mass ratio factor showed significant interference in the adsorption process of chromium and copper. The results obtained after optimization showed that the highest percentages of extraction (98%) were obtained on the following operating conditions: pH: 5-6, Concentration: 100 ppm and mass/ volume: 1 gram of fiber/50mL solution. The results showed that the adsorption process was efficient to remove chromium and copper using sisal fibers, however, requiring further studies to optimize the process.

PMMA based optical fiber Bragg grating for measuring moisture in transformer oil

Water contamination can cause serious problems that compromise in transformer's safe operation and reduce its lifetime. Online monitoring of moisture concentration in transformer oil would permit the control of moisture buildup. This letter presents a direct optical measurement of moisture concentration in transformer oil using a poly(methyl methacrylate) (PMMA)-based optical fiber Bragg grating (POFBG). The refractive index and volume of PMMA-based optical fiber vary with the moisture in the surrounding transformer oil, changing the reflecting wavelength of the grating. A sensitivity of POFBG wavelength change to moisture content of 29 pm/ppm is demonstrated in this letter, indicating detectable water content better than 0.05 ppm.

Developmental Potential of Bovine Hand-Made Clone Embryos Reconstructed by Aggregation or Fusion with Distinct Cytoplasmic Volumes

Animal cloning has been associated with developmental abnormalities, with the level of heteroplasmy caused by the procedure being one of its potential limiting factors. The aim of this study was to determine the effect of the fusion of hemicytoplasts or aggregation of hemiembryos, varying the final cytoplasmic volume, on development and cell density of embryos produced by hand-made cloning (HMC), parthenogenesis or by in vitro fertilization (IVF). One or two enucleated hemicytoplasts were paired and fused with one skin somatic cell. Activated clone and zona-free parthenote embryos and hemiembryos were in vitro cultured in the well-of-the-well (WOW) system, being allocated to one of six experimental groups, on a per WOW basis: single clone or parthenote hemiembryos (1 x 50%); aggregation of two (2 x 50%), three (3 x 50%), or four (4 x 50%) clone or parthenote hemiembryos; single clone or parthenote embryos (1 x 100%); or aggregation of two clone or parthenote embryos (2 x 100%). Control zona-intact parthenote or IVF embryos were in vitro cultured in four-well dishes. Results indicated that the increase in the number of aggregated structures within each WOW was followed by a linear increase in cleavage, blastocyst rate, and cell density. The increase in cytoplasmic volume, either by fusion or by aggregation, had a positive effect on embryo development, supporting the establishment of pregnancies and the birth of a viable clone calf after transfer to recipients. However, embryo aggregation did not improve development on a hemicytoplast basis, except for the aggregation of two clone embryos.

Electrodeposition and characterization of Cu-Nb composite coatings

Copper coatings containing well-distributed Nb particles were obtained by co-electrodeposition in an acidic sulfate bath. Nb particle concentration in the bath was the most significant factor for the incorporation of Nb particles in copper, followed by stirring rate, whereas current density presented low significance. High Nb particle concentration and low stirring rate led to a higher incorporated Nb particle content. The microhardness of the composite layers was higher than that of pure copper deposits obtained under the same conditions due to copper matrix grain refinement and increased with the increase of both current density and incorporated Nb particle volume fraction. The corrosion resistance of Cu-Nb composites in 0.5 wt.% H(2)SO(4) solution at room temperature was higher than that of pure copper and increased with the increase of the Nb content. (C) 2010 Elsevier B.V. All rights reserved.