Modelling the nonlinear behaviour and fracture process of AS4/PEKK thermoplastic composite under shear loading

The accurate determination of non-linear shear behaviour and fracture toughness of continuous carbon-fibre/polymer composites remains a considerable challenge. These measurements are often necessary to generate material parameters for advanced computational damage models. In particular, there is a dearth of detailed shear fracture toughness characterisation for thermoplastic composites which are increasingly generating renewed interest within the aerospace and automotive sectors. In this work, carbon fibre (AS4)/ thermoplastic Polyetherketoneketone (PEKK) composite V-notched cross-ply specimens were manufactured to investigate their non-linear response under pure shear loading. Both monotonic and cyclic loading were applied to study the shear modulus degradation and progressive failure. For the first time in the reported literature, we use the essential work of fracture approach to measure the shear fracture toughness of continuous fibre reinforced composite laminates. Excellent geometric similarity in the load-displacement curves was observed for ligament-scaled specimens. The laminate fracture toughness was determined by linear regression, of the specific work of fracture values, to zero ligament thickness, and verified with computational models. The matrix intralaminar fracture toughness (ply level fracture toughness), associated with shear loading was determined by the area method. This paper also details the numerical implementation of a new three-dimensional phenomenological model for carbon fibre thermoplastic composites using the measured values, which is able to accurately represent the full non-linear mechanical response and fracture process. The constitutive model includes a new non-linear shear profile, shear modulus degradation and load reversal. It is combined with a smeared crack model for representing ply-level damage initiation and propagation. The model is shown to accurately predict the constitutive response in terms of permanent plastic strain, degraded modulus as well as load reversal. Predictions are also shown to compare favourably with the evolution of damage leading to final fracture.

Optimal design of geometrically non- linear laminated structures

The mechanical properties of a laminate are strongly dependent of the fiber directions and because of that the lamenate should be designed to meet the specific requirements of each particular application in order to obtain the maximum advantages.

Optimal dynamic control of laminated adaptive structures using a higher order model and a genetic algorithm

This paper deals with a finite element formulation based on the classical laminated plate theory, for active control of thin plate laminated structures with integrated piezoelectric layers, acting as sensors and actuators. The control is initialized through a previous optimization of the core of the laminated structure, in order to minimize the vibration amplitude. Also the optimization of the patches position is performed to maximize the piezoelectric actuator efficiency. The genetic algorithm is used for these purposes. The finite element model is a single layer triangular plate/shell element with 24 degrees of freedom for the generalized displacements, and one electrical potential degree of freedom for each piezoelectric element layer, which can be surface bonded or embedded on the laminate. To achieve a mechanism of active control of the structure dynamic response, a feedback control algorithm is used, coupling the sensor and active piezoelectric layers. To calculate the dynamic response of the laminated structures the Newmark method is considered. The model is applied in the solution of an illustrative case and the results are presented and discussed.

Design of laminated structures using piezoelectric materials

Composite structures incorporating piezoelectric sensors and actuators are increasingly becoming important due to the offer of potential benefits in a wide range of engineering applications such as vibration and noise supression, shape control and precisition positioning. This paper presents a finit element formulation based on classical laminated plate theory for laminated structures with integrated piezoelectric layers or patches, acting as actuators. The finite element model is a single layer triangular nonconforming plate/shell element with 18 degrees of freedom for the generalized displacements, and one electrical potential degree of freedom for each piezsoelectric elementlayer or patch, witch are surface bonded on the laminate. An optimization of the patches position is performed to maximize the piezoelectric actuators efficiency as well as, the electric potential distribuition is search to reach the specified structure transverse displacement distribuition (shape control). A gradient based algorithm is used for this purpose. The model is applied in the optimization of illustrative laminated plate cases, and the results are presented and discussed.

Core and patch position optimizations for vibration control of piezolaminated structures

This paper deals with a finite formulation baserd on the classical laminated plate tehory, for active control of thin late laminated structures with integrated piezoelectric layers, acting as sensors and actuators. The control is initialized through a previuos optimization of the core of the laminated structure, in order to minimize the vibration amplitude. Also the optimization of the patches position in performed to maximize the piezoelectric actuator efficiency. the simulating annealing mthod is used for these purposes. The finite element model is a single layer triangular nonconforming plate/shell element with 18 degrees of fredom for the generalized displacements, and one electrical potential degree of freedom for each piezoelectric element layer, wich can be surface bonded or imbedded on the laminate. To achieve a mechanism of active control of the structure dynamic response, a feedback control algorirhm is used, coupling the sensor and active piezoelectric layers. To calculate the dynamic response of the laminated structures the Newmark method is considered. The model is applied in the solution of an illustrative case and the results are presented and discussed.

Modelling and aerodynamic simulation of a vehicle and failure analysis of a laminated front fender

Master Thesis in Mechanical Engineering field of Maintenance and Production

Uncertainty assessment approach for composite structures based on global sensitivity indices

The problem of uncertainty propagation in composite laminate structures is studied. An approach based on the optimal design of composite structures to achieve a target reliability level is proposed. Using the Uniform Design Method (UDM), a set of design points is generated over a design domain centred at mean values of random variables, aimed at studying the space variability. The most critical Tsai number, the structural reliability index and the sensitivities are obtained for each UDM design point, using the maximum load obtained from optimal design search. Using the UDM design points as input/output patterns, an Artificial Neural Network (ANN) is developed based on supervised evolutionary learning. Finally, using the developed ANN a Monte Carlo simulation procedure is implemented and the variability of the structural response based on global sensitivity analysis (GSA) is studied. The GSA is based on the first order Sobol indices and relative sensitivities. An appropriate GSA algorithm aiming to obtain Sobol indices is proposed. The most important sources of uncertainty are identified.

Uncertainty propagation in inverse reliability-based design of composite structures

An approach for the analysis of uncertainty propagation in reliability-based design optimization of composite laminate structures is presented. Using the Uniform Design Method (UDM), a set of design points is generated over a domain centered on the mean reference values of the random variables. A methodology based on inverse optimal design of composite structures to achieve a specified reliability level is proposed, and the corresponding maximum load is outlined as a function of ply angle. Using the generated UDM design points as input/output patterns, an Artificial Neural Network (ANN) is developed based on an evolutionary learning process. Then, a Monte Carlo simulation using ANN development is performed to simulate the behavior of the critical Tsai number, structural reliability index, and their relative sensitivities as a function of the ply angle of laminates. The results are generated for uniformly distributed random variables on a domain centered on mean values. The statistical analysis of the results enables the study of the variability of the reliability index and its sensitivity relative to the ply angle. Numerical examples showing the utility of the approach for robust design of angle-ply laminates are presented.

Buckling strength of adhesively-bonded single and double-strap repairs on carbon-epoxy structures

This work reports on an experimental and finite element method (FEM) parametric study of adhesively-bonded single and double-strap repairs on carbon-epoxy structures under buckling unrestrained compression. The influence of the overlap length and patch thickness was evaluated. This loading gains a particular significance from the additional characteristic mechanisms of structures under compression, such as fibres microbuckling, for buckling restrained structures, or global buckling of the assembly, if no transverse restriction exists. The FEM analysis is based on the use of cohesive elements including mixed-mode criteria to simulate a cohesive fracture of the adhesive layer. Trapezoidal laws in pure modes I and II were used to account for the ductility of most structural adhesives. These laws were estimated for the adhesive used from double cantilever beam (DCB) and end-notched flexure (ENF) tests, respectively, using an inverse technique. The pure mode III cohesive law was equalled to the pure mode II one. Compression failure in the laminates was predicted using a stress-based criterion. The accurate FEM predictions open a good prospect for the reduction of the extensive experimentation in the design of carbon-epoxy repairs. Design principles were also established for these repairs under buckling.

Tool effects on hybrid laminates drilling

Fiber reinforced plastics are increasing their importance as one of the most interesting groups of material on account of their low weight, high strength, and stiffness. To obtain good quality holes, it is important to identify the type of material, ply stacking sequence, and fiber orientation. In this article, the drilling of quasi-isotropic hybrid carbon +glass/epoxy plates is analyzed. Two commercial drills and a special step drill are compared considering the thrust force and delamination extension. Results suggest that the proposed step drill can be a suitable option in laminate drilling.

Estudo de falha em placas laminadas usando métodos analíticos e numéricos

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia de Manutenção

Soluções construtivas de fachadas em zinco

O presente trabalho foi realizado com o intuito de dar a conhecer, de um modo mais pormenorizado, os diferentes tipos de sistemas de revestimento de fachadas em zinco. Numa primeira fase abordou-se as características do metal zinco, assim como uma breve explicação do seu processo produtivo e a sua aplicação no campo da engenharia civil. O tema da sustentabilidade é também desenvolvido no que respeita à utilização do metal zinco na construção. Posteriormente serão especificadas certas propriedades do zinco laminado. É este tipo de zinco que será aplicado na envolvente exterior de edifícios. Numa fase posterior desenvolve-se a caracterização dos diversos tipos de sistemas construtivos de fachadas, com a respetiva descrição dos sistemas. São vários os sistemas disponíveis no mercado, sendo os mais utilizados em Portugal, os sistemas de junta agrafada, sistema de encaixe e sistema Camarinha. São ainda abordados os diversos suportes deste tipo de revestimento, as patologias que podem surgir e também as vantagens e limitações do zinco como material de revestimento. Por último é apresentado o estudo de um caso concreto, baseado num projeto de um edifício de habitação multifamiliar, e serão desenvolvidos aspetos como o tipo de sistema de fachada aplicado e o seu modo de execução, para além do estudo do desempenho térmico e acústico das fachadas e o seu custo de execução.

Ontario Forest Industries Association records, 1900-1989, n.d.

The Ontario Forest Industries Association (OFIA) was founded in 1944. It is a provincial trade association that represents member companies who produce a wide range of products, including pulp, paper, paperboard, lumber, panelboard, plywood and veneer. The OFIA works with its member companies to address issues of common interest and concern, and communicates these issues to the appropriate government, industrial or business sector. The Ontario Forest Information Service represented the OFIA from 1951 to 1988 as the publishers of their industry periodicals. Bush News was the first periodical published by the Service for the OFIA and ran until 1964, when it was replaced by Ontario Logger. In 1968, the name was changed to The Logger. In 1970, this was replaced by The Forest Scene. This new periodical was a departure from the earlier versions, which had served primarily as an internal communication system for the industry. The Forest Scene adopted a new format and editorial approach, emphasizing outdoor activities, recreation, hunting and fishing, conservation, and forestry operations and methods, thus appealing to a much wider readership. The Forest Scene ceased publication in 1988.

Variable mixed-mode delamination in composite laminates under fatigue conditions: testing & analysis

La majoria de les fallades en elements estructurals són degudes a càrrega per fatiga. En conseqüència, la fatiga mecànica és un factor clau per al disseny d'elements mecànics. En el cas de materials compòsits laminats, el procés de fallada per fatiga inclou diferents mecanismes de dany que resulten en la degradació del material. Un dels mecanismes de dany més importants és la delaminació entre capes del laminat. En el cas de components aeronàutics, les plaques de composit estan exposades a impactes i les delaminacions apareixen facilment en un laminat després d'un impacte. Molts components fets de compòsit tenen formes corbes, superposició de capes i capes amb diferents orientacions que fan que la delaminació es propagui en un mode mixt que depen de la grandària de la delaminació. És a dir, les delaminacions generalment es propaguen en mode mixt variable. És per això que és important desenvolupar nous mètodes per caracteritzar el creixement subcrític en mode mixt per fatiga de les delaminacions. El principal objectiu d'aquest treball és la caracterització del creixement en mode mixt variable de les delaminacions en compòsits laminats per efecte de càrregues a fatiga. Amb aquest fi, es proposa un nou model per al creixement per fatiga de la delaminació en mode mixt. Contràriament als models ja existents, el model que es proposa es formula d'acord a la variació no-monotònica dels paràmetres de propagació amb el mode mixt observada en diferents resultats experimentals. A més, es du a terme un anàlisi de l'assaig mixed-mode end load split (MMELS), la característica més important del qual és la variació del mode mixt a mesura que la delaminació creix. Per a aquest anàlisi, es tenen em compte dos mètodes teòrics presents en la literatura. No obstant, les expressions resultants per l'assaig MMELS no són equivalents i les diferències entre els dos mètodes poden ser importants, fins a 50 vegades. Per aquest motiu, en aquest treball es porta a terme un anàlisi alternatiu més acurat del MMELS per tal d'establir una comparació. Aquest anàlisi alternatiu es basa en el mètode dels elements finits i virtual crack closure technique (VCCT). D'aquest anàlisi en resulten importants aspectes a considerar per a la bona caracterització de materials utilitzant l'assaig MMELS. Durant l'estudi s'ha dissenyat i construït un utillatge per l'assaig MMELS. Per a la caracterització experimental de la propagació per fatiga de delaminacions en mode mixt variable s'utilitzen diferents provetes de laminats carboni/epoxy essencialment unidireccionals. També es du a terme un anàlisi fractogràfic d'algunes de les superfícies de fractura per delaminació. Els resultats experimentals són comparats amb les prediccions del model proposat per la propagació per fatiga d'esquerdes interlaminars.

Impact properties of glass/plant fibre hybrid laminates

The use of plants fibre reinforced composites has continuously increased during recent years. Their low density, higher environmental friendliness, and reduced cost proved particularly attractive for low-tech applications e.g., in building, automotive and leisure time industry. However, a major limitation to the use of these materials in structural components is unsatisfactory impact performance. An intermediate approach, the production of glass/ plant fibre hybrid laminates, has also been explored, trying to obtain materials with sufficient impact properties, whilst retaining a reduced cost and a substantial environmental gain. A survey is given on some aspects, crucial for the use of glass/plant fibre hybrid laminates in structural components: performance of hybrids when subjected to impact testing; the effect of laminate configuration, manufacturing procedure and fibre treatment on impact properties of the composite. Finally, indications are provided for a suitable selection of plant fibres with minimal extraction damage and sufficient toughness, for introduction in an impact-resistant glass/plant fibre hybrid laminate.