Influência do comprimento do pino de fibra de vidro na resistência à fratura de raízes fragilizadas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Experimento para quantificar a eficiência de aspersão de líquidos: aplicação em distribuidores espinha de peixe

This paper describes a device developed on the pilot scale and a simple approach to compare liquid distributor efficiencies. The technique consists basically of analyzing the mass of the liquid collected in 21 vertical pipes measuring 52 mm in internal diameter and 800 mm in length placed in a quadratic arrangement and positioned below the distributor A 50 mm thick acrylic blanket that does not disperse liquids was placed between the distributor and the pipe bank to avoid splashes. Assays were carried out with ladder-type distributors equipped with 4 parallel pipes each for a column measuring 400 nun in diameter as an example of the application. The number (n) of orifices (95, 127, and 159 orifices/m(2)), orifice diameter (d) (2, 3, and 4 mm) and the flowrate (q) (1.2; 1.4; and 1.6 m(3)/h) were varied. The best spread efficiency, which presented the lowest standard deviation, was achieved with 159 orifices, 2 mm and 1.4 m(3)/h. The pressure (p) at the distributor inlet for this condition was only 51000 Pa (0.51 kgf/cm(2)), while the average velocity (v) was 6.3 m/s in each orifice. These results show some limitations of the practical rules used in distributor designs.

Shear bond strength between Ni-Cr alloy bonded to a ceramic substrate

Shear bond strength between Ni-Cr alloy bonded to a ceramic substrate Introduction: The aim of this study was to evaluate the shear bond strength between a Ni-Cr alloy and a ceramic system submitted or not to thermocycling. Materials and methods: Forty-eight cylinder blocks of Ni-Cr with 3.0 mm diameter by 4.0 mm hight and 48 disc-shaped specimens (7.0 mm in diameter by 2.0 mm thick) composed of ceramic were prepared. The Ni-Cr cylinder blocks were randomised in two groups of 24 specimens each. One group was submitted to air-particle abrasion (sandblasting) with 50 mu m Al2O3 (0.4-0.7 MPa) during 20 s, and the other group was submitted to mechanical retentions with carbide burrs. Each group was subdivided into other two groups (n = 12), submitted or not to thermocycling (500 cycles, 5-55 degrees C). The cylinder blocks were bonded to the disc-shaped ceramic specimens under 10 N of load. The shear bond strengths (MPa) were measured using a universal testing machine at a cross head speed of 0.5 mm/min and 200 kgf of load. The data were submitted to statistical analysis (ANOVA and Tukey's test). Results: The air-particle abrasion group exhibited significantly higher shear bond strength when compared to drilled group (p < 0.05). Conclusions: Thermocycling decreased significantly the bond strengths for all groups tested.

Mechanical analysis of conventional and small diameter conical implant abutments

PURPOSE. The aim of the present study was to evaluate if a smaller morse taper abutment has a negative effect on the fracture resistance of implant-abutment connections under oblique compressive loads compared to a conventional abutment MATERIALS AND METHODS. Twenty morse taper conventional abutments (4.8 mm diameter) and smaller abutments (3.8 mm diameter) were tightened (20 Ncm) to their respective implants (3.5 x 11 mm) and after a 10 minute interval, implant/abutment assemblies were subjected to static compressive test, performed in a universal test machine with 1 mm/min displacement, at 45 degrees inclination. The maximum deformation force was determined. Data were statistically analyzed by student t test. RESULTS. Maximum deformation force of 4.8 mm and 3.8 mm abutments was approximately 95.33 kgf and 95.25 kgf, respectively, but no fractures were noted after mechanical test. Statistical analysis demonstrated that the evaluated abutments were statistically similar (P=.230). CONCLUSION. Abutment measuring 3.8 mm in diameter (reduced) presented mechanical properties similar to 4.8 mm (conventional) abutments, enabling its clinical use as indicated. [J Adv Prosthodont 2012;4:158-61]

The immediate effects of local and adjacent acupuncture on the tibialis anterior muscle: a human study

Abstract Background This study compares the immediate effects of local and adjacent acupuncture on the tibialis anterior muscle and the amount of force generated or strength in Kilogram Force (KGF) evaluated by a surface electromyography. Methods The study consisted of a single blinded trial of 30 subjects assigned to two groups: local acupoint (ST36) and adjacent acupoint (SP9). Bipolar surface electrodes were placed on the tibialis anterior muscle, while a force transducer was attached to the foot of the subject and to the floor. An electromyograph (EMG) connected to a computer registered the KGF and root mean square (RMS) before and after acupuncture at maximum isometric contraction. The RMS values and surface electrodes were analyzed with Student's t-test. Results Thirty subjects were selected from a total of 56 volunteers according to specific inclusion and exclusion criteria and were assigned to one of the two groups for acupuncture. A significant decrease in the RMS values was observed in both ST36 (t = -3.80, P = 0,001) and SP9 (t = 6.24, P = 0.001) groups after acupuncture. There was a decrease in force in the ST36 group after acupuncture (t = -2.98, P = 0.006). The RMS values did not have a significant difference (t = 0.36, P = 0.71); however, there was a significant decrease in strength after acupuncture in the ST36 group compared to the SP9 group (t = 2.51, P = 0.01). No adverse events were found. Conclusion Acupuncture at the local acupoint ST36 or adjacent acupoints SP9 reduced the tibialis anterior electromyography muscle activity. However, acupuncture at SP9 did not decrease muscle strength while acupuncture at ST36 did.

Impact of experimental Nano-HAP pastes on bovine enamel and dentin submitted to a pH cycling model

This in vitro study evaluated the preventive potential of experimental pastes containing 10% and 20% hydroxyapatite nanoparticles (Nano-HAP), with or without fluoride, on dental demineralization. Bovine enamel (n=15) and root dentin (n=15) specimens were divided into 9 groups according to their surface hardness: control (without treatment), 20 Nanop paste (20% HAP), 20 Nanop paste plus (20% HAP + 0.2% NaF), 10 Nanop paste (10% HAP), 10 Nanop paste plus (10% HAP + 0.2% NaF), placebo paste (without fluoride and HAP), fluoride paste (0.2% NaF), MI paste (CPP-ACP, casein phosphopeptide-amorphous calcium phosphate), and MI paste plus (CPP-ACP + 0.2% NaF). Both MI pastes were included as commercial control products containing calcium phosphate. The specimens were treated with the pastes twice a day (1 min), before and after demineralization. The specimens were subjected to a pH-cycling model (demineralization–6-8 h/ remineralization-16-18 h a day) for 7 days. The dental subsurface demineralization was analyzed using cross-sectional hardness (kgf/mm 2 , depth 10-220 µm). Data were tested using repeated-measures two-way ANOVA and Bonferroni's test (p<0.05). The only treatment able to reduce the loss of enamel and dentin subsurface hardness was fluoride paste (0.2% NaF), which differed significantly from the control at 30- and 50-µm depth (p<0.0001). The other treatments were not different from each other or compared with the control. The experimental Nanop pastes, regardless of the addition of fluoride, were unable to reduce dental demineralization in vitro.

Análise de força muscular e composição corporal de mulheres com Síndrome dos Ovários Policísticos

OBJETIVOS: Comparar os parâmetros metabólicos, a composição corporal e a força muscular de mulheres com Síndrome dos Ovários Policísticos (SOP) em relação a mulheres com ciclos menstruais ovulatórios. MÉTODOS: Estudo caso-controle com 27 mulheres com SOP e 28 mulheres controles com ciclos ovulatórios, com idade entre 18 e 37 anos, índice de massa corpórea entre 18 e 39,9 kg/m², que não praticassem atividade física regular. Níveis séricos de testosterona, androstenediona, prolactina, globulina carreadora dos hormônios sexuais (SHBG), insulina e glicemia foram avaliados. Índice de andrógeno livre (FAI) e resistência insulina (por HOMA) foram calculados. As voluntárias submetidas avaliação de composição corporal por dobras cutâneas e absorciometria de raio X de dupla energia (DEXA) e testes de força muscular máxima de 1-RM em três exercícios após procedimento de familiarização e de força isométrica de preensão manual. RESULTADOS: Os níveis de testosterona foram mais elevados no grupo SOP em relação ao CO (68,0±20,2 versus 58,2±12,8 ng/dL; p=0,02), assim como o FAI (282,5±223,8 versus 127,0±77,2; p=0,01), a insulina (8,4±7,0 versus 4,0±2,7 uIU/mL; p=0,01), e o HOMA (2,3±2,3 versus1,0±0,8; p=0,01). O SBHG foi inferior no grupo SOP comparado ao controle (52,5±43,3 versus 65,1±27,4 nmol/L; p=0,04). Não foram observadas diferenças significativas na composição corporal com os métodos propostos entre os grupos. O grupo SOP apresentou maior força muscular no teste de 1-RM nos exercícios supino reto (31,2±4,75 versus 27,8±3,6 kg; p=0,04) e cadeira extensora (27,9±6,2 versus 23,4±4,2 kg; p=0,01), assim como nos testes de força isométrica de preensão manual (5079,6±1035,7 versus 4477,3±69,6 kgf/m²; p=0,04). Ser portadora de SOP foi um preditor independente de aumento de força muscular nos exercícios supino reto (estimativa (E)=2,7) (p=0,04) e cadeira extensora (E=3,5) (p=0,04). Assim como o IMC no exercício de força isométrica de preensão manual do membro dominante (E=72,2) (p<0,01), supino reto (E=0,2) (p=0,02) e rosca direta (E=0,3) (p<0,01). Nenhuma associação foi encontrada entre HOMA-IR e força muscular. CONCLUSÕES: Mulheres com SOP apresentam maior força muscular, sem diferença na composição corporal. A RI não esteve associada ao desempenho da força muscular. Possivelmente, a força muscular pode estar relacionada aos níveis elevados de androgênios nessas mulheres.

Das deutsche Kriegsgefangenenwesen 1939 - 1945

Zusammenfassung: Die vorliegende Untersuchung zum deutschen Kriegsgefangenenwesen (KGW) im Zweiten Weltkrieg schließt eine wichtige Lücke innerhalb der geschichtswissenschaftlichen Forschungen zum Themenkreis der Kriegsgefangenschaft in deutschem Gewahrsam. Bisherige Studien (bis einschließlich 1997) behandeln vor allem sozial- und kulturgeschichtliche Aspekte der Kriegsgefangenen (Kgf.), der Lagergesellschaft und dem Alltag von Soldaten in Kriegsgefangenschaft. Der Verfasser indes legt mit seiner Magisterarbeit erstmals eine Organisations- und Strukturgeschichte des deutschen Kriegsgefangenenwesens von 1939 bis 1945 vor, welche fundamentale Grundlagen der deutschen militärischen Lagerorganisation und Verwaltung dokumentiert. So wird die Entwicklung von den Vorkriegsplanungen bis zum Kriegsende anhand der zentralen Dienststellen herausgearbeitet und im Kontext des Genfer Kriegsgefangenenabkommens von 1929 und völkerrechtlicher Implikationen gewichtet. Hiermit untrennbar verbundene Einflußnahmen nichtmilitärischer Stellen in die Entscheidungsgewalt der Streitkräfte im Heimatkriegsgebiet und in den Wehrmachtbefehlshaberbereichen werden nicht zuletzt auch anhand mehrerer Organigramme veranschaulicht. Zudem dokumentiert und analysiert die Untersuchung die im Kriegsverlauf stetig verschärften Maßnahmen zur Fluchtprävention und der konzertierten Fahndung nach geflohenen Kriegsgefangenen: Die Machterosion des Oberkommandos der Wehrmacht (OKW) zugunsten des Reichsführers-SS, des Reichssicherheitshauptamts und nicht zuletzt der Parteikanzlei der NSDAP wird so augenfällig. Trotz eminenter Schriftgutverluste kann der Verfasser vor allem anhand einer nahezu vollständig erhaltenen Schlüsselquelle die Stellenbesetzung und Organisationsstruktur der mit Kriegsgefangenenfragen befassten Stellen im OKW rekonstruieren. Die Auswertung dieser Sammelmitteilungen / Befehlssammlung für das Kriegsgefangenenwesen sowie an anderer Stelle überlieferter Organisationsbefehle ermöglicht wichtige Änderungen am derzeitigen Forschungsstand. Darüber hinaus beschäftigt sich die vorliegende Untersuchung mit dem Arbeitseinsatz Kriegsgefangener in der deutschen Wirtschaft als in der zweiten Kriegshälfte zentralem Element der Kriegsgefangenschaft. Außerdem wird beleuchtet, welche politischen, (rassen)ideologischen oder reziprok konnotierten Faktoren den Stellenwert gefangener Soldaten unterschiedlicher Nationalität innerhalb der Gefangenenhierarchie im deutschen Kriegsgefangenenwesen bestimmten. Inhalt: 1. Einführung; 2. Die Entwicklung des Kriegsvölkerrechts und das Genfer Kriegsgefangenenabkommen von 1929; 3. Einleitende Bemerkungen zum deutschen Kriegsgefangenenwesen: Quellenlage, Grundlagen; 4. Organisationsstruktur und Aufgaben des KGW: Zuständigkeiten für Kgf. in OKW und OKH, Abt. Wehrmachtverluste und Kriegsgefangene, der General z.b.V. für das KGW 1939 bis Ende 1941, Allgemeine und Organisationsabteilung seit Januar 1942, Generalinspekteur und Inspekteur des KGW von Juli 1943 bis Oktober 1944, das Kriegsgefangenenwesen unter Himmler seit Oktober 1944; 5. Die Kriegsgefangenenlager: Lagertypen, Anzahl und Verwendung, die Gesamtzahl Kgf. und Belegstärken ausgewählter Lager; 6. Richtlinien für KGL: Die Sammelmitteilungen / Befehlssammlung für das KGW, Lagerorganisation und Behandlung Kriegsgefangener; 7. Die Post der Kriegsgefangenen: Tätigkeit von Auslandsbriefprüfstelle, Abwehr III Referat Kgf. und Abwehrstellen der Wehrkreise, Vorgaben für Postüberwachung und Stimmungsberichte der Asten, Befehle zur Kgf-Post und Kooperation mit Hilfsorganisationen und Schutzmächten; 8. Fluchtprävention: Bestimmungen und Maßnahmen zur Fluchtvereitelung, der Fluchterlass vom 22.09.1942, der Sonderfahndungsplan der Sicherheitspolizei und des SD vom 28.09.1942, Erlass zur Kriegsfahndung vom 5.12.1942, der Fluchterlaß vom 02.07.1943, der Erlaß zur Mitarbeit NSDAP bei Groß- und Kriegsfahndungen vom 10.07.1943, Schulung zur Fluchtprävention auf Wehrkreisebene 1944, Preisausschreiben "Wie verhindere ich Fluchten?" vom 09.04.1945, Anwerbung von V-Leuten durch die Abwehr; 9. Arbeitseinsatz Kriegsgefangener in der deutschen Wirtschaft und beteiligte Stellen; 10. Der Status Kriegsgefangener unterschiedlicher Nationalitäten im Vergleich; 11. Schluss

Poscosecha de ciruela variedad angeleno : conservación frigorífica tradicional y en atmósfera modificada

Objetivos: reducir pérdidas durante la conservación frigorífica, emplear atmósfera modificada como método suplementario a la refrigeración, alargar el período de aptitud comercial. Metodología: se trabajó con fruta acondicionada a 0±1 °C y 90±5 % HR, según las siguientes variantes: 1. testigo: 20 kg fruta a granel sin seleccionar en caja plástica; 2. granel + film PVC: 10 kg de fruta a granel en bandejas de madera más cartón corrugado recubierta con film de PVC; 3. celpack: bandejas de madera recubiertas de cartón corrugado con dos celpack de 23 frutos cada uno; 4. celpack + atmósfera modificada: ídem anterior pero cada celpack en bolsa de polietileno de baja densidad de 20 μ. A partir de los 30 días de conservación se extrajo semanalmente, durante 9 semanas, una muestra de 46 frutos, de los cuales 23 fueron analizados al momento de ser extraídos y los 23 restantes luego de 48 horas de comercialización simulada (sc). Para la evaluación estadística se aplicó análisis de la varianza con el programa SAS (Statistical Analysis System) y se determinaron las diferencias entre tratamientos con el test de Duncan. Para sabor, en cambio, se aplicó una prueba de homogeneidad de P2. La evaluación de sabor se realizó mediante degustación con panel de 5 catadores entrenados. Resultados: Los frutos tenían las siguientes características al inicio de conservación: calibre 61.4 mm, peso 117.8 g, firmeza de pulpa 3.1 kgf, sabor agridulce, contenido de sólidos solubles 17.5 °Bx, acidez 0.78 g ác. málico%g, % cubrimiento 83.69 %. Luego de la conservación frigorífica (97días): % de color de cobertura 95 %. La firmeza de la pulpa en el tratamiento celpack + bolsa se diferencia con valores más altos, media de 2.8 kgf , el resto con media 2.6 kgf. En sc la firmeza es inferior y esta disminución es menor en celpack + bolsa. Sólidos solubles, media 17.21 °Bx, en sc valores con media de un 0.3 % más. Acidez titulable: disminución progresiva, de 0.68 a 0.47 g%g al fin de conservación. Sabor: a partir de los 59 días aumentan los frutos insípidos y desagradables excepto en celpack + bolsa. Síntomas de deshidratación: a partir de los 79 días la única variante que no presenta síntomas es celpack + bolsa. Conclusiones: El acondicionamiento en celpack redujo la incidencia de ataque por mohos (fue el único tratamiento sin ataque durante 94 días); tampoco presentó sabores desagradables y su limitación en conservación se debió a la deshidratación evidente a partir de 74 días. La fruta embalada en celpack + bolsa tuvo mayores valores de resistencia a la presión y 100 % de frutos sin deshidratación a los 94 días de conservación; a partir de 80 días es evidente el ataque de mohos y frutos con sabores desagradables. Las variantes granel y granel + film presentan deterioro por deshidratación a partir de 74 días. La conservación no debería superar 80 días. Celpack + bolsa muestra mejores resultados, con mayores valores de resistencia a la presión que los otros tratamientos; con respecto al sabor, mantiene una mayor proporción de sabor dulce.

Fluorescence in situ hybridization analysis of keratinocyte growth factor gene amplification and dispersion in evolution of great apes and humans

Keratinocyte growth factor (KGF) is a member of the fibroblast growth factor family. Portions of the gene encoding KGF were amplified during primate evolution and are present in multiple nonprocessed copies in the human genome. Nucleotide analysis of a representative sampling of these KGF-like sequences indicated that they were at least 95% identical to corresponding regions of the KGF gene. To localize these sequences to specific chromosomal sites in human and higher primates, we used fluorescence in situ hybridization. In human, using a cosmid probe encoding KGF exon 1, we assigned the location of the KGF gene to chromosome 15q15–21.1. In addition, copies of KGF-like sequences hybridizing only with a cosmid probe encoding exons 2 and 3 were localized to dispersed sites on chromosome 2q21, 9p11, 9q12–13, 18p11, 18q11, 21q11, and 21q21.1. The distribution of KGF-like sequences suggests a role for alphoid DNA in their amplification and dispersion. In chimpanzee, KGF-like sequences were observed at five chromosomal sites, which were each homologous to sites in human, while in gorilla, a subset of four of these homologous sites was identified; in orangutan two sites were identified, while gibbon exhibited only a single site. The chromosomal localization of KGF sequences in human and great ape genomes indicates that amplification and dispersion occurred in multiple discrete steps, with initial KGF gene duplication and dispersion taking place in gibbon and involving loci corresponding to human chromosomes 15 and 21. These findings support the concept of a closer evolutionary relationship of human and chimpanzee and a possible selective pressure for such dispersion during the evolution of higher primates.

Pulmonary malformation in transgenic mice expressing human keratinocyte growth factor in the lung.

Expression of human keratinocyte growth factor (KGF/FGF-7) was directed to epithelial cells of the developing embryonic lung of transgenic mice disrupting normal pulmonary morphogenesis during the pseudoglandular stage of development. By embryonic day 15.5(E15.5), lungs of transgenic surfactant protein C (SP-C)-KGF mice resembled those of humans with pulmonary cystadenoma. Lungs were cystic, filling the thoracic cavity, and were composed of numerous dilated saccules lined with glycogen-containing columnar epithelial cells. The normal distribution of SP-C proprotein in the distal regions of respiratory tubules was disrupted. Columnar epithelial cells lining the papillary structures stained variably and weakly for this distal respiratory cell marker. Mesenchymal components were preserved in the transgenic mouse lungs, yet the architectural relationship of the epithelium to the mesenchyme was altered. SP-C-KGF transgenic mice failed to survive gestation to term, dying before E17.5. Culturing mouse fetal lung explants in the presence of recombinant human KGF also disrupted branching morphogenesis and resulted in similar cystic malformation of the lung. Thus, it appears that precise temporal and spatial expression of KGF is likely to play a crucial role in the control of branching morphogenesis during fetal lung development.

Adesivo de contato de policloropreno base aquosa nanoaditivado e condicionado magneticamente.

Atualmente, os adesivos de contato de policloropreno base aquosa, possuem capacidade de adesão, variando entre 1,15 até 2,75 kgf/cm2. Em contrapartida, os adesivos de policloropreno base solvente, suportam tensões médias de cisalhamento de 3,8 kgf/cm2. Esta pesquisa apresenta uma proposta inovadora de condicionamento magnético do adesivo de contato de policloropreno base aquosa com o objetivo de aumentar a capacidade de aderência entre o adesivo e o substrato. Para promover um incremento na capacidade de adesão do adesivo de policloropreno base aquosa, formulou-se um adesivo utilizando um nanoaditivo, o gás carbônico como catalisador e um processo de condicionamento magnético precedente à etapa de aplicação sobre os substratos. Os resultados obtidos demonstraram aumento médio de 292 % na tensão de cisalhamento do adesivo condicionado magneticamente quando comparado com o adesivo de mesma formulação sem o condicionamento magnético, e quando comparado com um adesivo comercial de policloropreno base aquosa, o aumento foi de 122 %.

Wear of high aluminium zinc-based alloys in plain bearing applications

Two zinc-based alloys of high aluminium content, Super Cosmal alloy containing 60% Al, 6% Si, 1% Cu, 0.3% Mn and HAZCA alloy containing 60% Al, 8% Si, 2% Cu, 0.06% Mg were produced by sand casting. Foundry characteristics in particular, fluidity, mode of solidification and feeding ability were examined. Metallographic analysis of structures was carried out using optical and scanning electron microscopy and their mechanical properties were determined using standard techniques. Dry wear characteristics were determined using a pin-on-disc test, and boundary-lubricated wear was studied using full bearing tests. Results from casting experiments were evaluated and compared with the behaviour of a standard ZA-27 alloy and those from tribological tests with both ZA-27 alloy and a leaded tin-bronze (SAE660) under the same testing conditions. The presence of silicon was beneficial, reducing the temperature range of solidification, improving feeding efficiency and reducing gravity segregation of phases. Use of chills and melt degassing was found necessary to achieve soundness and enhanced mechanical properties. Dry wear tests were performed against a steel counterface for sliding speeds of 0.25, 0.5, 1.0 and 2 m/s and for a range of loads up to 15 kgf. The high aluminium alloys showed wear rates as low as those of ZA-27 at speeds of 0.25 and 0.5 m/s for the whole range of applied loads. ZA-27 performed better at higher speeds. The build up of a surface film on the wearing surface of the test pins was found to be responsible for the mild type of wear of the zinc based alloys. The constitution of the surface film was determined as a complex mixture of aluminium, zinc and iron oxides and metallic elements derived from both sliding materials. For full bearing tests, bushes were machined from sand cast bars and were tested against a steel shaft in the presence of a light spindle oil as the lubricant. Results showed that all zinc based alloys run-in more rapidly than bronze, and that wear in Super Cosmal and HAZCA alloys after prolonged running were similar to those in ZA-27 bearings and significantly smaller than those of the bronze.

Estudo da incorporação de cinza e chamote gerado pela cerâmica vermelha ao próprio processo industrial

The ceramics industry generates waste at various stages of that process, defective products, waste from burning solid fuels, among others. This waste is dumped in landfills, garbage dumps or directly on roads, which has a negative environmental impact. This paper presents a study to incorporate the waste of algaroba wood and chamote (scrap pieces of ceramic already sintered), in to the ceramic material for making sealing blocks. The methodological procedures consist in the characterization of chemical and mineralogical residues, raw materials, and physical-mechanical of the formulations of mixes with clay, silt and waste. By pressing test pieces were produced using a pressure of 200 kgf/cm², varying compositions in the range of 0%, 5%, 10% and 15% by weight of residue. The sintering was performed in a muffle furnace, with the temperature levels of 850 ° C, 900 ° C, 950 ° C, 1000 ° C and 1050 ° C. The evaluated physical and mechanical properties were: Water Absorption, Linear Shrinkage Burning, Apparent Porosity, Apparent Density and Mechanical Resistance to Flexion. Analysis was carried out by Scanning Electron Microscopy on fracture surfaces of the specimens. Evaluation of linear shrinkage property drying and firing , water absorption and mechanical resistance to compression of the sealing blocks 5% wood ash residue, sintered at 900 °C hold temperature in the laboratory the products manufactured on an industrial scale. The main results, it was found on the viability of using the residues of algaroba wood and to confer refractory properties of the ceramic product. The main results, it was concluded feasibility of using the ash residues algaroba wood to impart refractory properties to the ceramic product and the residue of chamote, being derived from the own ceramic product not interfere with the properties, when used in a percentage of up to 5%.Since the residue of chamote being derived from the ceramic product itself had no effect on the properties. Studies in the laboratory have shown that the incorporation of up to 5% of these residues may be adopted as an alternative technology to reduce the environmental impact caused by the industrial sector, without compromising the final properties of the material, since the results on an industrial scale showed absorption values 11.66 and 11.74 of water and waste products respectively, within the parameters of NBR - 15,270, since the mechanical strength was 1.25 MPa and 0.94 MPa respectively for products with and without residue, lower than the minimum required by the technical standard that is 1.5 MPa.

Estudo da incorporação de cinza e chamote gerado pela cerâmica vermelha ao próprio processo industrial

The ceramics industry generates waste at various stages of that process, defective products, waste from burning solid fuels, among others. This waste is dumped in landfills, garbage dumps or directly on roads, which has a negative environmental impact. This paper presents a study to incorporate the waste of algaroba wood and chamote (scrap pieces of ceramic already sintered), in to the ceramic material for making sealing blocks. The methodological procedures consist in the characterization of chemical and mineralogical residues, raw materials, and physical-mechanical of the formulations of mixes with clay, silt and waste. By pressing test pieces were produced using a pressure of 200 kgf/cm², varying compositions in the range of 0%, 5%, 10% and 15% by weight of residue. The sintering was performed in a muffle furnace, with the temperature levels of 850 ° C, 900 ° C, 950 ° C, 1000 ° C and 1050 ° C. The evaluated physical and mechanical properties were: Water Absorption, Linear Shrinkage Burning, Apparent Porosity, Apparent Density and Mechanical Resistance to Flexion. Analysis was carried out by Scanning Electron Microscopy on fracture surfaces of the specimens. Evaluation of linear shrinkage property drying and firing , water absorption and mechanical resistance to compression of the sealing blocks 5% wood ash residue, sintered at 900 °C hold temperature in the laboratory the products manufactured on an industrial scale. The main results, it was found on the viability of using the residues of algaroba wood and to confer refractory properties of the ceramic product. The main results, it was concluded feasibility of using the ash residues algaroba wood to impart refractory properties to the ceramic product and the residue of chamote, being derived from the own ceramic product not interfere with the properties, when used in a percentage of up to 5%.Since the residue of chamote being derived from the ceramic product itself had no effect on the properties. Studies in the laboratory have shown that the incorporation of up to 5% of these residues may be adopted as an alternative technology to reduce the environmental impact caused by the industrial sector, without compromising the final properties of the material, since the results on an industrial scale showed absorption values 11.66 and 11.74 of water and waste products respectively, within the parameters of NBR - 15,270, since the mechanical strength was 1.25 MPa and 0.94 MPa respectively for products with and without residue, lower than the minimum required by the technical standard that is 1.5 MPa.