DEVELOPMENT AND IMPLEMENTATION OF A REMOTE AUDIT TOOL FOR HIGH DOSE RATE (HDR) 192IR BRACHYTHERAPY USING OPTICALLY STIMULATED LUMINESCENCE DOSIMETRY

This work aimed to create a mailable and OSLD-based phantom with accuracy suitable for RPC audits of HDR brachytherapy sources at institutions participating in NCI-funded cooperative clinical trials. An 8 × 8 × 10 cm3 prototype with two slots capable of holding nanoDot Al2O3:C OSL dosimeters (Landauer, Glenwood, IL) was designed and built. The phantom has a single channel capable of accepting all 192Ir HDR brachytherapy sources in current clinical use in the United States. Irradiations were performed with an 192Ir HDR source to determine correction factors for linearity with dose, dose rate, and the combined effect of irradiation energy and phantom construction. The uncertainties introduced by source positioning in the phantom and timer resolution limitations were also investigated. It was found that the linearity correction factor was where dose is in cGy, which differed from that determined by the RPC for the same batch of dosimeters under 60Co irradiation. There was no significant dose rate effect. Separate energy+block correction factors were determined for both models of 192Ir sources currently in clinical use and these vendor-specific correction factors differed by almost 2.6%. For Nucletron sources, this correction factor was 1.026±0.004 (99% Confidence Interval) and for Varian sources it was 1.000±0.007 (99% CI). Reasonable deviations in source positioning within the phantom and the limited resolution of the source timer had insignificant effects on the ability to measure dose. Overall measurement uncertainty of the system was estimated to be ±2.5% for both Nucletron and Varian source audits (95% CI). This uncertainty was sufficient to establish a ±5% acceptance criterion for source strength audits under a formal RPC audit program. Trial audits of eight participating institutions resulted in an average RPC-to-institution dose ratio of 1.000 with a standard deviation of 0.011.

Evaluation of PRESAGE® dosimeters for brachytherapy sources and the 3D dosimetry and characterization of the new AgX100 125I seed model

With continuous new improvements in brachytherapy source designs and techniques, method of 3D dosimetry for treatment dose verifications would better ensure accurate patient radiotherapy treatment. This study was aimed to first evaluate the 3D dose distributions of the low-dose rate (LDR) Amersham 6711 OncoseedTM using PRESAGE® dosimeters to establish PRESAGE® as a suitable brachytherapy dosimeter. The new AgX100 125I seed model (Theragenics Corporation) was then characterized using PRESAGE® following the TG-43 protocol. PRESAGE® dosimeters are solid, polyurethane-based, 3D dosimeters doped with radiochromic leuco dyes that produce a linear optical density response to radiation dose. For this project, the radiochromic response in PRESAGE® was captured using optical-CT scanning (632 nm) and the final 3D dose matrix was reconstructed using the MATLAB software. An Amersham 6711 seed with an air-kerma strength of approximately 9 U was used to irradiate two dosimeters to 2 Gy and 11 Gy at 1 cm to evaluate dose rates in the r=1 cm to r=5 cm region. The dosimetry parameters were compared to the values published in the updated AAPM Report No. 51 (TG-43U1). An AgX100 seed with an air-kerma strength of about 6 U was used to irradiate two dosimeters to 3.6 Gy and 12.5 Gy at 1 cm. The dosimetry parameters for the AgX100 were compared to the values measured from previous Monte-Carlo and experimental studies. In general, the measured dose rate constant, anisotropy function, and radial dose function for the Amersham 6711 showed agreements better than 5% compared to consensus values in the r=1 to r=3 cm region. The dose rates and radial dose functions measured for the AgX100 agreed with the MCNPX and TLD-measured values within 3% in the r=1 to r=3 cm region. The measured anisotropy function in PRESAGE® showed relative differences of up to 9% with the MCNPX calculated values. It was determined that post-irradiation optical density change over several days was non-linear in different dose regions, and therefore the dose values in the r=4 to r=5 cm regions had higher uncertainty due to this effect. This study demonstrated that within the radial distance of 3 cm, brachytherapy dosimetry in PRESAGE® can be accurate within 5% as long as irradiation times are within 48 hours.

(Table 3) Concentration of Au, Pd, and Pt in the interstitial waters of ODP Leg 125 samples

Palladium, platinum, and gold were analyzed for 20 interstitial water samples from Leg 125. No Pd or Pt was detected in fluids from serpentinite muds from Conical Seamount in the Mariana forearc, indicating that low-temperature seawater-peridotite interaction does not mobilize these elements into the serpentinizing fluids to levels above 0.10 parts per billion (ppb) in solution. However, Au may be mobilized in high pH solutions. In contrast, fluids from vitric-rich clays on the flanks of the Torishima Seamount in the Izu-Bonin forearc have Pd values of between 4.0 and 11.8 nmol/L, Pt values between 2.3 and 5.0 nmol/L and Au values between 126.9 and 1116.9 pmol/L. The precious metals are mobilized, and possibly adsorbed onto clay mineral surfaces, during diagenesis and burial of the volcanic-rich clays. Desorption during squeezing of the sediments may produce the enhanced precious metal concentrations in the analyzed fluids. The metals are mobilized in the fluids probably as neutral hydroxide, bisulfide, and ammonia complexes. Pt/Pd ratios are between 0.42 and 2.33, which is much lower than many of the potential sources for Pt and Pd but is consistent with the greater solubility of Pd compared with Pt in most natural low-temperature fluids.

(Table 1) Interstitial-water chemistry at DSP Leg 58 Holes

Interstitial waters from several sites drilled during Leg 58 have been analyzed for major constituents. Data for Sites 442, 443, and 444 in Shikoku Basin indicate that only small changes occur in the chemical composition. We did not note any influence on the interstitial water chemistry resulting from reactions taking place in the underlying basalts. Site 445 data indicate that reactions must occur in the sediment column, leading to decreases in dissolved magnesium and increases in dissolved calcium. In addition, a source of dissolved calcium appears in the underlying basalts. At Site 446, changes appear in dissolved-calcium and -magnesium concentrations, resulting mainly from alteration reactions in the basalts. Dissolved potassium has its main sink in deeper-lying sediments or basalts. Changes in dissolved strontium at Sites 445 and 446 can be explained in terms of carbonate recrystallization. At all sites, changes in dissolved manganese and lithium appear to be related to the presence of biogenic silica in the sediments.

Interstitial water chemistry at DSDP Leg 57 Holes

Analyses of water samples taken by means of an in-hole sampler generally show good agreement with analyses of samples collected by routine shipboard squeezing techniques. At Sites 438 and 439, a decrease in salinity with depth is related to former freshwater flow from an aquifer that crops out at an anticline on a deep sea terrace between Japan and the top of the trench slope of the Japan Trench. This former subaerial recharge suggests significant late Cenozoic subsidence of the terrace, because it now lies at a water depth of 1500 meters. Samples from the trench slope at Site 440 have extremely high values of alkalinity and ammonia, presumably because of a favorable combination of high sedimentation rate and organic carbon content. Diagenetic conditions on the trench slope favor formation of the Fe-Mg carbonate mineral, ankerite; at Site 440 it first occurs at a depth below the sea floor of only 29 meters in late Pleistocene strata. Undissolved diatoms persist to relatively great depth at the sites of Leg 57 because of a low geothermal gradient caused by subduction. Secondary silica lepispheres first appear at 851 meters at the most landward and warmest site, Site 438, in strata 16 million years old with an ambient temperature of 31 °C.

Chemical composition of interstitial waters from sediments of brine-bearing deeps of the Red Sea

Data on concentrations of the major ions (Cl, SO4, Alk, Na, K, Ca, Mg, NH4) in interstitial waters from sediments of three brine-bearing deeps of the Red Sea rift zone are reported. Interstitial waters of the Atlantis-II Deep have the highest salinity (310.1 g/l), of the Discovery Deep - slightly lower (298.8 g/l), and of the Suakin Deep - the lowest (159.9 g/l). Interstitial waters of all three deeps are characterized by low, compared with sea water, absolute and relative concentrations of Mg and SO4 ions and have extremely low alkaline reserve (0.15-0.64 meq/l). Concentrations of K, Ca and especially Na and Cl ions, as compared with sea water, are highly increased. Interstitial waters from the deeps in study have high, compared with sea water, concentrations of NH4 (12-62 mg/l).

Interstitial-water geochemistry of Kerguelen Plateau sediments

This report synthesizes all of the interstitial-water chemistry studies associated with the Kerguelen Plateau phase of ODP Leg 119. Sediments were cored at six sites (49°24'S to 59°36'S) in water depths ranging from 564 to 4082 m. A total of 77 interstitial-water samples was recovered as part of the routine sampling protocol. In addition, a novel, highresolution pore-water sampling program was tested during Leg 119 that enabled us to pinpoint reaction zones and extend our data base to deeper, drier levels that were heretofore inaccessible. Data collected include interstitial-water sodium, potassium, calcium, magnesium, pH, alkalinity, sulfate, ammonia, phosphate, aqueous silica, salinity, chloride, oxidation-reduction potentials, and sediment chemistry. The northern sector (Sites 736 and 737) is characterized by the highest sedimentation rates (up to 140 m/m.y.) and thermal gradients (70°-98°C/km) encountered on the Kerguelen Plateau during Leg 119. Site 737 represents the most reactive sediment column cored on the Kerguelen Plateau. Major cation fluxes at Site 737 are the strongest measured during Leg 119. High dissolved calcium concentrations (141.5 mM) were encountered near the bottom of Hole 737B. Elevated temperatures promote silica diagenesis and the alteration of volcanic material below 300 mbsf, and a diagenetic front was discovered near 370 mbsf at Site 737. The southern portion of the Kerguelen Plateau (Sites 738 and 744) records the lowest sedimentation rates (less than 5 m/m.y.) and thermal gradients (43°C/km) of the three study areas. Major cation fluxes at the southern sites are the lowest that we measured on the Kerguelen Plateau. High-resolution sampling provided evidence for significant silica release to the pore waters during the weathering of basement basalt. The relatively low thermal gradient does not appear to be sufficient for the formation of the opal-CT and quartz chert beds and nodules that were encountered below 120 mbsf at Site 738. Sediment-accumulation rates on the Eastern Kerguelen Sediment Ridge (Sites 745 and 746) are intermediate to those of the northern and southern sites. Deposition below the regional CCD accounts for the nearly carbonate-free, siliceous sediments. Despite their low organic carbon contents (mean = 0.15%), sediments on the Eastern Kerguelen Sediment Ridge exhibit the highest pore-water alkalinity (6.77 mM), ammonium (0.50 mM), and phosphate (23 µM) concentrations measured on the Kerguelen Plateau. Major cation fluxes are intermediate to those calculated for the northern and southern sites. The Eastern Kerguelen Sediment Ridge interstitial waters are unusual, however, in that the downward flux of magnesium is greater than the upward flux of calcium.

Isotopic composition of oxygen, carbon, and sulfur in interstitial water and cores at DSDP Leg 59 Holes

Comprehensive isotopic studies based on data from the Deep Sea Drilling Project have elucidated numerous details of the low- and high-temperature mechanisms of interaction between water and rocks of ocean crustal seismic Layers 1 and 2. These isotopic studies have also identified climatic changes during the Meso-Cenozoic history of oceans. Data on the abundance and isotopic composition of sulfur in the sedimentary layer as well as in rocks of the volcanic basement are more fragmentary than are oxygen and carbon data. In this chapter we specifically concentrate upon isotopic data related to specific features of the mechanisms of low-temperature interaction of water with sedimentary and volcanogenic rocks. The Leg 59 data provide a good opportunity for such lithologic and isotopic studies, because almost 600 meters of basalt flows and sills interbedded with tuffs and volcaniclastic breccias were cored during the drilling of Hole 448A. Moreover, rocks supposedly exposed to hydrothermal alteration play an important role at the deepest horizons of that mass. Sulfur isotopic studies of the character of possible biogenic processes of sulfate reduction in sediments are another focus, as well as the nature and origin of sulfide mineralization in Layer-2 rocks of remnant island arcs. Finally, oxygen and carbon istopic analyses of biogenic carbonates in the cores also enabled us to investigate the effects of changing climatic conditions during the Cenozoic. These results are compared with previous data from adjacent regions of the Pacific Ocean. Thus this chapter describes results of isotopic analyses of: oxygen and sulfur of interstitial water; oxygen and carbon of sedimentary carbonates and of calcite intercalations and inclusions in tuffs and volcaniclastic breccias interbedded with basalt flows; and sulfur of sulfides in these rocks.

Chemical and isotope compositions of interstitial water in sediments from Mediterranean basin at DSDP Sites 42-372 and 42-374

The Br/Cl, Li/Cl and B/Cl ratios and boron isotope compositions of hypersaline pore fluids from DSDP Sites 372 and 374 were measured in an attempt to evaluate the origin of the brines. In Site 374 the relationships between the Cl concentrations (up to 5000 mM) and Br/Cl (~0.012), Na/Cl (as low as 0.1), B/Cl (0.0025), and d11B values (43-55?) of the deep pore water between 380 and 405 mbsf, located within the Messinian sediments, reflect remnants of ~65-fold evaporated sea water. The original evaporated sea water was modified by: (1) dilution with overlying or less saline water by about 30%; and (2) slight dissolution of NaCl evaporites. The variations in d11B show a continuous increase in d11B values with depth in Site 374, up to 66.7? at a depth of 300 mbsf (Upper Pliocene marl sediments). The conspicuous 11B enrichment trend is consistent with elemental boron depletion, which was calculated from the expected boron concentrations of evaporated sea water with corresponding Br/Cl and Na/Cl ratios. Li/Cl variations also show a depletion of Li relative to evaporated sea water. The apparent depletions of B and Li, as well as the 11B enrichment, reflect uptake of these elements by clay minerals at low water/sediment ratios.

Interstitial water chemistry of ODP Leg 103 sites

Interstitial waters were squeezed from strata recovered at Sites 637-641 of ODP Leg 103 on the Galicia margin, along the northwestern Iberian continental margin in the northeast Atlantic. Chemical profiles of Site 638 show the most complexity, which appears to be related to an unconformity in the strata between Cretaceous and Neogene sediments and to rapid deposition of Cretaceous syn-rift sediments upon pre-rift strata. Analyses of waters from all of the Leg 103 sites show generally antithetical trends for calcium and magnesium; calcium increases with depth as magnesium decreases. No calcium-magnesium 'crossover' profiles are observed in these data. Data from Site 637 show an unusual pattern; calcium increases with increasing depth, but magnesium remains relatively constant. Sulfate is either stable or shows an overall decrease with depth, and boron profiles show some structure. At all but one site (Site 638), strontium profiles do not show marked depth structure. The structure of alkalinity and silica profiles is highly site dependent. Bromide profiles are, in general, constant. In nearly every case, observed bromide concentrations are near average seawater values. Relatively low concentrations of iron and manganese are common within the upper 10 m of the sediment sequence and typically are near detection limits at deeper depths

Isotopic composition of interstitial fluids in sediment at DSDP Sites 87-582 and 87-583

The isotopic compositions of dissolved CO2 and CH4 in sediments of the Nankai Trough indicate that CH4 is formed during early diagenesis by microbial reduction of CO2. At the shallowest sampled depths, the CO2 dissolved in the pore water is unusually enriched in 12C (d13C = -35.2 per mil), indicating contribution of CO2 from oxidation of CH4. The most intense microbiological activity appears to be confined to the uppermost 50 m of sediment, based on relative lack of change in the isotopic compositions below this depth. Gas hydrate probably is not present at these localities (Sites 582, 583) because of CH4 concentrations that are insufficient to saturate the pore water with respect to gas hydrate stability.

Iron and manganese in bottom sediments and interstitial waters sampled in the White Sea on August 21-30, 2003

Iron and manganese in bottom sediments studied along the sublatitudinal transect from Kandalaksha to Arkhangelsk are characterized by various contents and speciations depending on sedimentation environment, grain size of sediments, and diagenetic processes. The latter include redistribution of reactive forms leading to enrichment in Fe and Mn of surface sediments, formation of films, incrustations, and ferromanganese nodules. Variations in total Fe content (2-8%) are accompanied by changes in concentration of its reactive forms (acid extraction) and concentration of dissolved Fe in interstitial waters (1-14 µM). Variations in Mn content in bottom sediments (0.03-3.7%) and interstitial waters (up to 500 µM) correspond to high diagenetic mobility of this element. Changes in oxidation degree of chemical elements result in redox stratification of sediment strata with maximum concentrations of Fe, Mn, and sulfides. Organic matter of bottom sediments with considerable terrestrial constituent is oxidized by bottom water oxygen mainly at the sediment surface or in anaerobic conditions within the sediment strata. The role of inorganic components in organic matter oxidation changes from surface layer bottom sediments (where manganese oxyhydroxide dominates among oxidants) to deeper layers (where sulfate of interstitial water serves as the main oxidant). Differences in river runoff and hydrodynamics are responsible for geochemical asymmetry of the transect. The deep Kandalaksha Bay serves as a sediment trap for manganese (Mn content in sediments varies within 0.5-0.7%), whereas the sedimentary environment in the Dvina Bay promotes its removal from bottom sediments (Mn 0.05%).

Chemical and strontium isotopic compositions of interstitial waters from sediments of ODP Site 135-841

The depth variations in the major chemical components dissolved in interstitial waters from the Tonga margin (ODP Site 841) are much more pronounced than those usually observed in deep-sea sediments. The extensive alteration of volcanic Miocene sediments to secondary minerals such as analcime, clays, and thaumasite forms a CaCl2-rich brine. The brine results from a high exchange of Ca to Na, K, and Mg and an increase in Cl concentrations due to removal of H2O from the fluid during the authigenesis of hydrous minerals. The formation of thaumasite could have partly controlled the concentration of dissolved SO4, HCO3, and Ca in the Miocene sediments. The strontium isotopic signature of the interstitial water suggests that alteration of the volcanic Miocene sediments occurred a long time after sedimentation. A transient diffusion model indicates that molecular diffusion was not prevented by lithologic barriers and that the formation of secondary minerals in the Miocene sediment occurred over a short period of time (e.g.,

Geochemistry of interstitial waters of DSDP Leg 96 sites

Interstitial water studies were done at 9 of the 11 sites visited in the Mississippi Fan and Orca and Pigmy Basins during DSDP Leg 96. High concentrations of sulfate were observed at Mississippi Fan Sites 616, 617, 620, and 623. The maximum sulfate value of 38.8 mM, recorded at Site 617, is the highest ever found in DSDP sediments. Hypersaline interstitial water was observed at Site 618 in Orca Basin. Concentration ratios of salinity to chlorinity and to sodium in interstitial waters are similar to those of Orca Basin bottom water, suggesting that the chemistry of interstitial water is affected by the dissolution of buried salt.