Using an LED as a sensor and visible light communication device in a smart illumination system

The need for more efficient illumination systems has led to the proliferation of Solid-State Lighting (SSL) systems, which offer optimized power consumption. SSL systems are comprised of LED devices which are intrinsically fast devices and permit very fast light modulation. This, along with the congestion of the radio frequency spectrum has paved the path for the emergence of Visible Light Communication (VLC) systems. VLC uses free space to convey information by using light modulation. Notwithstanding, as VLC systems proliferate and cost competitiveness ensues, there are two important aspects to be considered. State-of-the-art VLC implementations use power demanding PAs, and thus it is important to investigate if regular, existent Switched-Mode Power Supply (SMPS) circuits can be adapted for VLC use. A 28 W buck regulator was implemented using a off-the-shelf LED Driver integrated circuit, using both series and parallel dimming techniques. Results show that optical clock frequencies up to 500 kHz are achievable without any major modification besides adequate component sizing. The use of an LED as a sensor was investigated, in a short-range, low-data-rate perspective. Results show successful communication in an LED-to-LED configuration, with enhanced range when using LED strings as sensors. Besides, LEDs present spectral selective sensitivity, which makes them good contenders for a multi-colour LED-to-LED system, such as in the use of RGB displays and lamps. Ultimately, the present work shows evidence that LEDs can be used as a dual-purpose device, enabling not only illumination, but also bi-directional data communication.

Sensores “em movimento"

A domótica e a Internet das Coisas (Internet of Things – IoT) são dois conceitos que estão a ter bastante impacto na sociedade e a mudar o seu quotidiano, pelo que o utilizador é mais exigente na utilização dos seus equipamentos, pretendendo, que sejam mais simples e eficazes. A IoT é também muito utilizada na vertente da qualidade de vida (verificação da qualidade do ar, temperatura etc.) pelo que é necessário a utilização de uma rede de sensores de forma que toda a informação recolhida seja disponibilizada ao utilizador. Os sensores estão ligados a nós da rede de forma a recolherem informação. Essa rede pode ser constituída por diferentes topologias, sendo que a mais usual é a rede em Malha, pois no caso de um dos nós deixar de funcionar, a mensagem é enviada através de outros nós até chegar ao nó principal. O passo seguinte consiste em enviar toda essa informação para a Cloud, sendo que, nas soluções existentes, é necessário que o utilizador tenha um ponto fixo (gateway) com acesso à internet. Quando não é possível internet por cabo, a solução é a utilização de redes sem fios ou a utilização de, por exemplo, um cartão 3G/4G que implica o pagamento de taxas às operadoras móveis. Estas soluções implicam, na sua grande maioria uma instalação elétrica para alimentação dos nós dos sensores. O grande problema surge quando o utilizador não possui nenhum acesso à Internet (no local onde são instalados os sensores), ou no caso de não existência de nenhuma instalação elétrica para alimentação dos nós dos sensores. A solução proposta nesta dissertação consiste na utilização de um telemóvel, de um utilizador aleatório, como gateway. Assim, um utilizador comum pode ligar os seus sensores onde for necessário. Esses sensores são configurados Over-The-Air através de uma camada de aplicação do dispositivo de comunicação, como por exemplo, o Synapse. Após configuração, os sensores estão prontos a recolher toda a informação e enviá-la através da rede até ao nó principal. O nó principal é constituído pelo dispositivo de comunicação referido anteriormente, ligado a um microcontrolador (Arduino, por exemplo) que tem agregado um leitor de cartões SD e um dispositivo Bluetooth (BLE). Toda a informação recolhida pelos sensores é guardada no cartão SD até que um utilizador, com um telemóvel (Smartphone Android com a aplicação desenvolvida instalada) com o Bluetooth ligado, se aproxime do nó principal. Assim que a ligação é aceite e estabelecida, a aplicação envia a data mais recente de um sensor específico presente na sua base de dados na Cloud para o Arduino, permitindo que este apague os dados mais antigos presentes no cartão e envie, como resposta para o telemóvel, a informação mais antiga recolhida pelo sensor, atualizando assim a informação. A aplicação deste conceito pode ser útil quando não existe nenhuma ligação à internet ou quando um utilizador, por exemplo uma entidade responsável pelo meio ambiente e que seja necessário inserir sensores numa floresta, para prevenção de fogos. Assim os nós vão enviar toda a informação recolhida através da sua rede. Posteriormente, cabe ao utilizador escolher um sítio estratégico, onde saiba que irão passar indivíduos com alguma frequência, de modo a que estes recebam essa informação para o seu telemóvel.

The names of things: terminology and the practice of art history

This paper aims to explore the ways in which standard art history terminology shapes the practice of art history by conditioning the interpretation of specific works of art and, in certain cases, the definition of a research subject (especially where questions of genre and periodization are concerned). Taking as a case study a painting by Georges de La Tour, the Peasant Couple Eating, I will argue that terms such as realism, realistic, naturalistic etc. used for its description and/or interpretation, far from constituting objective stylistic characterizations, shape our perception of the work in question. Bringing the question of social class to the center of the discourse on realism, I propose to show how the social divide between the painter and his subject matter (in this case, the peasants) is internalized in the painting’s style and meaning, and how it is fundamental for the understanding of its intentionality and function.

Semantic architecture for sensors

Based on the report for the unit “Sociology of New Information Technologies” of the Master on Computer Sciences at FCT/University Nova Lisbon in 2015-16. The responsible of this curricular unit is Prof. António Moniz

From a NoSQL data source to a business intelligence solution: An experiment

We are living in the era of Big Data. A time which is characterized by the continuous creation of vast amounts of data, originated from different sources, and with different formats. First, with the rise of the social networks and, more recently, with the advent of the Internet of Things (IoT), in which everyone and (eventually) everything is linked to the Internet, data with enormous potential for organizations is being continuously generated. In order to be more competitive, organizations want to access and explore all the richness that is present in those data. Indeed, Big Data is only as valuable as the insights organizations gather from it to make better decisions, which is the main goal of Business Intelligence. In this paper we describe an experiment in which data obtained from a NoSQL data source (database technology explicitly developed to deal with the specificities of Big Data) is used to feed a Business Intelligence solution.

Child abuse monitor system model: a health care critical knowledge monitor system

The Childhood protection is a subject with high value for the society, but, the Child Abuse cases are difficult to identify. The process from suspicious to accusation is very difficult to achieve. It must configure very strong evidences. Typically, Health Care services deal with these cases from the beginning where there are evidences based on the diagnosis, but they aren’t enough to promote the accusation. Besides that, this subject it’s highly sensitive because there are legal aspects to deal with such as: the patient privacy, paternity issues, medical confidentiality, among others. We propose a Child Abuses critical knowledge monitor system model that addresses this problem. This decision support system is implemented with a multiple scientific domains: to capture of tokens from clinical documents from multiple sources; a topic model approach to identify the topics of the documents; knowledge management through the use of ontologies to support the critical knowledge sensibility concepts and relations such as: symptoms, behaviors, among other evidences in order to match with the topics inferred from the clinical documents and then alert and log when clinical evidences are present. Based on these alerts clinical personnel could analyze the situation and take the appropriate procedures.

Detection of Leishmania braziliensis in human paraffin-embedded tissues from Tucumán, Argentina by polymerase chain reaction

American cutaneous leishmaniasis (ACL) is an endemic disease in Northern Argentina. We applied the polymerase chain reaction (PCR) followed by a hybridization labelled probe to 21 paraffin embedded human skin biopsies, already analyzed histologically, from leishmaniasis endemic areas in the province of Tucumán, Argentina. We used primers previously designed to detect a Leishmania-specific 120-base-pair fragment of kinetoplast DNA minicircle, other two primer pairs that amplify kDNA minicircles belonging to the L. braziliensis and L. mexicana complexes respectively, and specific oligonucleotide primers to detect L. (V.) braziliensis which amplify the sequence of the ribosomal protein L-14 of this species. The PCR-hybridization showed a sensitivity of 90.5% when compared to the histopathology test which was 61.9%. Five of the total samples analyzed were positive for the L. braziliensis complex whilst none was positive for the L. mexicana complex. The specific primers for L. (V.) braziliensis detected the parasite in four samples. These results are consistent with those reported for close endemic areas and demonstrate that the causative agent of human leishmaniasis in the analyzed cases was L. (V.) braziliensis. PCR should be used as a diagnostic tool for tegumentary leishmaniasis, especially in the mucosal form, and as a valuable technique for the identification of the Leishmania species that causes the disease in certain areas.

Open source business strategies in the domain of embedded systems

El tema de este estudio es el aumento de la comprensión teórica y empírica de la estrategia de negocio de código abierto en el dominio de sistemas embebidos por investigar modelos de negocios de código abierto, retos, recursos y capacidades operativas y dinámicas.

Three essays on major trends in a slow clockspeed industry : the case of industrial automation

The motivation for this research initiated from the abrupt rise and fall of minicomputers which were initially used both for industrial automation and business applications due to their significantly lower cost than their predecessors, the mainframes. Later industrial automation developed its own vertically integrated hardware and software to address the application needs of uninterrupted operations, real-time control and resilience to harsh environmental conditions. This has led to the creation of an independent industry, namely industrial automation used in PLC, DCS, SCADA and robot control systems. This industry employs today over 200'000 people in a profitable slow clockspeed context in contrast to the two mainstream computing industries of information technology (IT) focused on business applications and telecommunications focused on communications networks and hand-held devices. Already in 1990s it was foreseen that IT and communication would merge into one Information and communication industry (ICT). The fundamental question of the thesis is: Could industrial automation leverage a common technology platform with the newly formed ICT industry? Computer systems dominated by complex instruction set computers (CISC) were challenged during 1990s with higher performance reduced instruction set computers (RISC). RISC started to evolve parallel to the constant advancement of Moore's law. These developments created the high performance and low energy consumption System-on-Chip architecture (SoC). Unlike to the CISC processors RISC processor architecture is a separate industry from the RISC chip manufacturing industry. It also has several hardware independent software platforms consisting of integrated operating system, development environment, user interface and application market which enables customers to have more choices due to hardware independent real time capable software applications. An architecture disruption merged and the smartphone and tablet market were formed with new rules and new key players in the ICT industry. Today there are more RISC computer systems running Linux (or other Unix variants) than any other computer system. The astonishing rise of SoC based technologies and related software platforms in smartphones created in unit terms the largest installed base ever seen in the history of computers and is now being further extended by tablets. An underlying additional element of this transition is the increasing role of open source technologies both in software and hardware. This has driven the microprocessor based personal computer industry with few dominating closed operating system platforms into a steep decline. A significant factor in this process has been the separation of processor architecture and processor chip production and operating systems and application development platforms merger into integrated software platforms with proprietary application markets. Furthermore the pay-by-click marketing has changed the way applications development is compensated: Three essays on major trends in a slow clockspeed industry: The case of industrial automation 2014 freeware, ad based or licensed - all at a lower price and used by a wider customer base than ever before. Moreover, the concept of software maintenance contract is very remote in the app world. However, as a slow clockspeed industry, industrial automation has remained intact during the disruptions based on SoC and related software platforms in the ICT industries. Industrial automation incumbents continue to supply systems based on vertically integrated systems consisting of proprietary software and proprietary mainly microprocessor based hardware. They enjoy admirable profitability levels on a very narrow customer base due to strong technology-enabled customer lock-in and customers' high risk leverage as their production is dependent on fault-free operation of the industrial automation systems. When will this balance of power be disrupted? The thesis suggests how industrial automation could join the mainstream ICT industry and create an information, communication and automation (ICAT) industry. Lately the Internet of Things (loT) and weightless networks, a new standard leveraging frequency channels earlier occupied by TV broadcasting, have gradually started to change the rigid world of Machine to Machine (M2M) interaction. It is foreseeable that enough momentum will be created that the industrial automation market will in due course face an architecture disruption empowered by these new trends. This thesis examines the current state of industrial automation subject to the competition between the incumbents firstly through a research on cost competitiveness efforts in captive outsourcing of engineering, research and development and secondly researching process re- engineering in the case of complex system global software support. Thirdly we investigate the industry actors', namely customers, incumbents and newcomers, views on the future direction of industrial automation and conclude with our assessments of the possible routes industrial automation could advance taking into account the looming rise of the Internet of Things (loT) and weightless networks. Industrial automation is an industry dominated by a handful of global players each of them focusing on maintaining their own proprietary solutions. The rise of de facto standards like IBM PC, Unix and Linux and SoC leveraged by IBM, Compaq, Dell, HP, ARM, Apple, Google, Samsung and others have created new markets of personal computers, smartphone and tablets and will eventually also impact industrial automation through game changing commoditization and related control point and business model changes. This trend will inevitably continue, but the transition to a commoditized industrial automation will not happen in the near future.

Reframing the relationship between service design and operations: a service engineering approach

The significance of services as business and human activities has increased dramatically throughout the world in the last three decades. Becoming a more and more competitive and efficient service provider while still being able to provide unique value opportunities for customers requires new knowledge and ideas. Part of this knowledge is created and utilized in daily activities in every service organization, but not all of it, and therefore an emerging phenomenon in the service context is information awareness. Terms like big data and Internet of things are not only modern buzz-words but they are also describing urgent requirements for a new type of competences and solutions. When the amount of information increases and the systems processing information become more efficient and intelligent, it is the human understanding and objectives that may get separated from the automated processes and technological innovations. This is an important challenge and the core driver for this dissertation: What kind of information is created, possessed and utilized in the service context, and even more importantly, what information exists but is not acknowledged or used? In this dissertation the focus is on the relationship between service design and service operations. Reframing this relationship refers to viewing the service system from the architectural perspective. The selected perspective allows analysing the relationship between design activities and operational activities as an information system while maintaining the tight connection to existing service research contributions and approaches. This type of an innovative approach is supported by research methodology that relies on design science theory. The methodological process supports the construction of a new design artifact based on existing theoretical knowledge, creation of new innovations and testing the design artifact components in real service contexts. The relationship between design and operations is analysed in the health care and social care service systems. The existing contributions in service research tend to abstract services and service systems as value creation, working or interactive systems. This dissertation adds an important information processing system perspective to the research. The main contribution focuses on the following argument: Only part of the service information system is automated and computerized, whereas a significant part of information processing is embedded in human activities, communication and ad-hoc reactions. The results indicate that the relationship between service design and service operations is more complex and dynamic than the existing scientific and managerial models tend to view it. Both activities create, utilize, mix and share information, making service information management a necessary but relatively unknown managerial task. On the architectural level, service system -specific elements seem to disappear, but access to more general information elements and processes can be found. While this dissertation focuses on conceptual-level design artifact construction, the results provide also very practical implications for service providers. Personal, visual and hidden activities of service, and more importantly all changes that take place in any service system have also an information dimension. Making this information dimension visual and prioritizing the processed information based on service dimensions is likely to provide new opportunities to increase activities and provide a new type of service potential for customers.

Control of a line robot system with Embedded Linux

Many, if not all, aspects of our everyday lives are related to computers and control. Microprocessors and wireless communications are involved in our lives. Embedded systems are an attracting field because they combine three key factors, small size, low power consumption and high computing capabilities. The aim of this thesis is to study how Linux communicates with the hardware, to answer the question if it is possible to use an operating system like Debian for embedded systems and finally, to build a Mechatronic real time application. In the thesis a presentation of Linux and the Xenomai real time patch is given, the bootloader and communication with the hardware is analyzed. BeagleBone the evaluation board is presented along with the application project consisted of a robot cart with a driver circuit, a line sensor reading a black line and two Xbee antennas. It makes use of Xenomai threads, the real time kernel. According to the obtained results, Linux is able to operate as a real time operating system. The issue of future research is the area of embedded Linux is also discussed.

Kiihtyvyyteen perustuva langaton iskuvoimanmittausjärjestelmä

Tämä lopputyö esittelee Diter Oy:n toimeksiannosta läpiviedyn projektin, jonka tarkoituksena oli luoda langaton etäluettava ja -ohjattava kiihtyvyyden mittaukseen perustuva iskuvoimanmittausjärjestelmän prototyyppi. Projektin tarkoitus ei ollut luoda viimeisteltyä mittausjärjestelmää, vaan selvittää onko tällaista järjestelmää ylipäätään mahdollista toteuttaa järkevästi. Mittajärjestelmän idean taustalla oli vahvasti Internet-of-Things (IoT) -konsepti, minkä seurauksena hallinta ja seuraaminen toteutettiin esitettyjen vaatimusten mukaan Android-pohjaiselle mobiililaitteelle. Langaton tiedonsiirto toteutettiin Bluetoothyhteydellä, jonka välityksellä mobiililaitteelle toteutetun sovelluksen avulla pystytään ohjaamaan Bluetooth-moduulin kytkettyä mikrokontrolleria. Mikrokontrolleri lukee AD-muuntimeen kytkettyä analogista kiihtyvyysanturia, jota käytetään tallentamaan kappaleeseen kohdistuvien voimien aiheuttama kiihtyvyys. Toimeksiantoon kuului koko laitteisto- ja ohjelmistoarkkitehtuurin suunnittelu ja toteutus alusta alkaen. Järjestelmän lisäksi projektiin kuului verifiointitestausten suunnitellu ja toteutus, jotka ovat myös kuvattuna tässä työssä. Tärkeänä osana verifiointia olivat kiihtyvyysanturin kalibroinnin tarkastaminen sekä kalibrointimenetelmän toteutus. Verifiointitestauksissa käytettiin servo-ohjattua sähkömoottoria luomaan ympyräliike, josta voitiin vertaamalla kierrostaajuutta ja kiihtyvyysarvoja toisiinsa todentaa kiihtyvyysanturin kalibrointi. Lisäksi rakennettiin Newtonin kehtoon perustuva testipenkki, jonka avulla pyrittiin selvittämään järjestelmän mahdollista iskuvoimanmittauskykyä. Vaikka suoritettujen testausten tulokset olivat aluksi lupaavia, eivät ne lopulta olleet yksiselitteiset. Tämän seurauksena työ ei pystynyt sille kohdennettujen resurssien puittessa ottamaan kantaa annettuun tutkimuskysymykseen. Tulokset kuitenkin osoittivat, mitä on otettava huomioon jatkosuunnittelussa ja verifiointitestausten kehittämisessä.