Cartografia geotécnica subterrânea do maciço granítico de Arca d’Água (Paranhos): implicações para o modelo geomecânico comportamental

Mestrado em Engenharia Geotécnica e Geoambiente

Contribuição para o estudo da combinação de cal com cimento no tratamento de solos

Mestrado em Engenharia Geotécnica e Geoambiente

Mass spectrometry parameters optimization for the 46 multiclass pesticides determination in strawberries with gas chromatography ion-trap tandem mass spectrometry

Multiclass analysis method was optimized in order to analyze pesticides traces by gas chromatography with ion-trap and tandem mass spectrometry (GC-MS/MS). The influence of some analytical parameters on pesticide signal response was explored. Five ion trap mass spectrometry (IT-MS) operating parameters, including isolation time (IT), excitation voltage (EV), excitation time (ET),maximum excitation energy or “q” value (q), and isolationmass window (IMW) were numerically tested in order to maximize the instrument analytical signal response. For this, multiple linear regression was used in data analysis to evaluate the influence of the five parameters on the analytical response in the ion trap mass spectrometer and to predict its response. The assessment of the five parameters based on the regression equations substantially increased the sensitivity of IT-MS/MS in the MS/MS mode. The results obtained show that for most of the pesticides, these parameters have a strong influence on both signal response and detection limit.Using the optimized method, a multiclass pesticide analysis was performed for 46 pesticides in a strawberry matrix. Levels higher than the limit established for strawberries by the European Union were found in some samples.

Cartografia geotécnica subterrânea do maciço granítico de Arca D'Água (sector de Carvalhido–Burgães): implicações para o modelo geomecânico comportamental

Este trabalho pretende enfatizar a importância da elaboração de uma base de dados extensa e robusta para o melhoramento da cartografia geotécnica subterrânea do maciço granítico do sector de Carvalhido–Burgães (Porto). Este estudo envolveu a análise e o refinamento das principais características geomecânicas ao longo de um traçado com cerca de 1220 m, para a caracterização do maciço rochoso da galeria subterrânea Carvalhido–Burgães. Para esta caracterização foram coligidos e uniformizados dados geológicos, geotécnicos e geomecânicos relativos a várias campanhas de campo, realizadas entre 2005 e 2011, tendo estado a técnica da amostragem linear aplicada ao grau de compartimentação do maciço rochoso na base do seu estudo. Além disso, procedeu‐se a um tratamento estatístico das descontinuidades, bem como dos parâmetros geológico‐geotécnicos e geomecânicos a estas associados. O zonamento geotécnico do maciço granítico foi realizado sempre em estreita ligação com o conhecimento das características do maciço in situ. Pretende‐se que esta metodologia contribua para um melhor conhecimento da compartimentação dos maciços rochosos em geral e, em particular, do modelo geomecânico comportamental do maciço rochoso do Porto.

Estudo de soluções de contenção periférica em função das condicionantes de execução

Dissertação de natureza científica para obtenção do grau de Mestre em Engenharia Civil

As características geotécnicas de um maciço como factores preponderantes na planificação e organização de obras de escavação subterrâneas - uma perspectiva sobre a produção

Com o presente documento pretende-se abordar e identificar os diferentes factores que influenciam directamente a produção e execução de uma escavação subterrânea, com especial relevo sobre a influência exercida pela geotecnia do maciço intersectado. Inicialmente são focados os principais aspectos a ter em conta na caracterização geotécnica de um maciço, seguindo-se uma introdução a diferentes métodos de escavação actuais e metodologias de suporte de uma obra subterrânea, com particular realce para os utilizados em maciços brandos. Depois de tratados estes conceitos, é apresentada uma obra subterrânea em execução que foi acompanhada durante 4 meses para efeitos de desenvolvimento deste estudo. Assim, são abordados neste documento diferentes aspectos construtivos, no que diz respeito à mão-de-obra utilizada, metodologias e técnicas aplicadas, redes técnicas auxiliares instaladas, produções e rendimentos verificados. De seguida e de modo a atestar a importância da caracterização geotécnica ao longo da obra, foi feito um estudo do maciço intersectado, relativamente às descontinuidades que o intersectam, litologia, alteração, e resistência à compressão. Para este último parâmetro foram utilizadas técnicas distintas mas complementares, nomeadamente o ensaio de carga pontual (em laboratório), e o esclerómetro portátil (in situ). Por último, tendo em conta os parâmetros e características presentes e as implicações que uma obra do género acarreta, são propostas de modo sucinto, técnicas alternativas de escavação do maciço cuja viabilidade de implementação seja possível no contexto em questão.

Geotecnia dos túneis do maciço de Paranhos: avaliação hidrogeomecânica exploratória

As classificações geomecânicas são uma das abordagens mais reconhecidas para estimar a qualidade do maciço rochoso, face à sua simplicidade e competência para gerir incertezas. As incertezas geológicas e geotécnicas podem ser avaliadas de forma eficaz usando classificações adequadas. Este estudo pretende enfatizar a importância das classificações geomecânicas e índices geomecânicos, tais como a Rock Mass Rating (RMR), a Rock Tunnelling Quality Index (Qsystem), o Geological Strength Index (GSI) e o Hydro‐Potential (HP) Value, para ajuizar a qualidade do maciço rochoso granítico das galerias subterrâneas de Paranhos (setor de Carvalhido ‐ Burgães; área urbana do Porto). Em particular, o valor hidro‐potencial (HP‐value) é uma classificação semi‐quantitativa aplicada a maciços rochosos que permite estimar as infiltrações de água subterrânea em escavações de terrenos rochosos. Para esta avaliação foi compilada e integrada uma extensa base de dados geológico‐geotécnica e geomecânica, apoiada na técnica de amostragem linear de superfícies expostas descontinuidades. Para refinar o zonamento geotécnico do maciço rochoso granítico, previamente realizado em 2010, foram coletadas amostras de rocha em pontos‐chave, com o objetivo de avaliar a sua resistência através do Ensaio de Carga Pontual (PLT). A aplicação das classificações geomecânicas foi realizada de uma forma equilibrada, estabelecendo diferentes cenários e tendo sempre em conta o conhecimento das características do maciço in situ. Apresenta‐se uma proposta de zonamento hidrogeomecânico com o objetivo de compreender melhor a circulação geo‐hidráulica do maciço rochoso granítico. Pretende‐se com esta metodologia contribuir para aprofundar o conhecimento do substrato rochoso do Porto, nomeadamente no que diz respeito ao seu comportamento geomecânico.

Geotecnia urbana da zona ribeirinha de Vila Nova de Gaia (Cais de Gaia, Santa Marinha – Lavadores, Canidelo): uma avaliação preliminar

Mestrado em Engenharia Geotécnica e Geoambiente

The influence of count's number in myocardium in the determination of reproducible parameters in Gated-SPECT studies simulated with GATE

Myocardial Perfusion Gated Single Photon Emission Tomography (Gated-SPET) imaging is used for the combined evaluation of myocardial perfusion and left ventricular (LV). The purpose of this study is to evaluate the influence of the total number of counts acquired from myocardium, in the calculation of myocardial functional parameters using routine software procedures. Methods: Gated-SPET studies were simulated using Monte Carlo GATE package and NURBS phantom. Simulated data were reconstructed and processed using the commercial software package Quantitative Gated-SPECT. The Bland-Altman and Mann-Whitney-Wilcoxon tests were used to analyze the influence of the number of total counts in the calculation of LV myocardium functional parameters. Results: In studies simulated with 3MBq in the myocardium there were significant differences in the functional parameters: Left ventricular ejection fraction (LVEF), end-systolic volume (ESV), Motility and Thickness; between studies acquired with 15s/projection and 30s/projection. Simulations with 4.2MBq show significant differences in LVEF, end-diastolic volume (EDV) and Thickness. Meanwhile in the simulations with 5.4MBq and 8.4MBq the differences were statistically significant for Motility and Thickness. Conclusion: The total number of counts per simulation doesn't significantly interfere with the determination of Gated-SPET functional parameters using the administered average activity of 450MBq to 5.4MBq in myocardium.

Properties of tantalum oxynitride thin films produced by magnetron sputtering: the influence of processing parameters

The main purpose of this work is to present and to interpret the change of structure and physical properties of tantalum oxynitride (TaNxOy) thin films, produced by dc reactive magnetron sputtering, by varying the processing parameters. A set of TaNxOy films was prepared by varying the reactive gases flow rate, using a N2/O2 gas mixture with a concentration ratio of 17:3. The different films, obtained by this process, exhibited significant differences. The obtained composition and the interpretation of X-ray diffraction results, shows that, depending on the partial pressure of the reactive gases, the films are: essentially dark grey metallic, when the atomic ratio (N + O)/Ta < 0.1, evidencing a tetragonal β-Ta structure; grey-brownish, when 0.1 < (N + O)/Ta < 1, exhibiting a face-centred cubic (fcc) TaN-like structure; and transparent oxide-type, when (N + O)/Ta > 1, evidencing the existence of Ta2O5, but with an amorphous structure. These transparent films exhibit refractive indexes, in the visible region, always higher than 2.0. The wear resistance of the films is relatively good. The best behaviour was obtained for the films with (N + O)/Ta ≈ 0.5 and (N + O)/Ta ≈ 1.3.

Tissue composition and density impact on the clinical parameters for 125I prostate implants dosimetry

The MCNPX code was used to calculate the TG-43U1 recommended parameters in water and prostate tissue in order to quantify the dosimetric impact in 30 patients treated with (125)I prostate implants when replacing the TG-43U1 formalism parameters calculated in water by a prostate-like medium in the planning system (PS) and to evaluate the uncertainties associated with Monte Carlo (MC) calculations. The prostate density was obtained from the CT of 100 patients with prostate cancer. The deviations between our results for water and the TG-43U1 consensus dataset values were -2.6% for prostate V100, -13.0% for V150, and -5.8% for D90; -2.0% for rectum V100, and -5.1% for D0.1; -5.0% for urethra D10, and -5.1% for D30. The same differences between our water and prostate results were all under 0.3%. Uncertainties estimations were up to 2.9% for the gL(r) function, 13.4% for the F(r,θ) function and 7.0% for Λ, mainly due to seed geometry uncertainties. Uncertainties in extracting the TG-43U1 parameters in the MC simulations as well as in the literature comparison are of the same order of magnitude as the differences between dose distributions computed for water and prostate-like medium. The selection of the parameters for the PS should be done carefully, as it may considerably affect the dose distributions. The seeds internal geometry uncertainties are a major limiting factor in the MC parameters deduction.

PV system modeling by five parameters and in situ test

This paper focuses on a novel formalization for assessing the five parameter modeling of a photovoltaic cell. An optimization procedure is used as a feasibility problem to find the parameters tuned at the open circuit, maximum power, and short circuit points in order to assess the data needed for plotting the I-V curve. A comparison with experimental results is presented for two monocrystalline PV modules.

Effect of technical parameters on dose and image quality in a computed radiography system

The discovery of X-rays was undoubtedly one of the greatest stimulus for improving the efficiency in the provision of healthcare services. The ability to view, non-invasively, inside the human body has greatly facilitated the work of professionals in diagnosis of diseases. The exclusive focus on image quality (IQ), without understanding how they are obtained, affect negatively the efficiency in diagnostic radiology. The equilibrium between the benefits and the risks are often forgotten. It is necessary to adopt optimization strategies to maximize the benefits (image quality) and minimize risk (dose to the patient) in radiological facilities. In radiology, the implementation of optimization strategies involves an understanding of images acquisition process. When a radiographer adopts a certain value of a parameter (tube potential [kVp], tube current-exposure time product [mAs] or additional filtration), it is essential to know its meaning and impact of their variation in dose and image quality. Without this, any optimization strategy will be a failure. Worldwide, data show that use of x-rays has been increasingly frequent. In Cabo Verde, we note an effort by healthcare institutions (e.g. Ministry of Health) in equipping radiological facilities and the recent installation of a telemedicine system requires purchase of new radiological equipment. In addition, the transition from screen-films to digital systems is characterized by a raise in patient exposure. Given that this transition is slower in less developed countries, as is the case of Cabo Verde, the need to adopt optimization strategies becomes increasingly necessary. This study was conducted as an attempt to answer that need. Although this work is about objective evaluation of image quality, and in medical practice the evaluation is usually subjective (visual evaluation of images by radiographer / radiologist), studies reported a correlation between these two types of evaluation (objective and subjective) [5-7] which accredits for conducting such studies. The purpose of this study is to evaluate the effect of exposure parameters (kVp and mAs) when using additional Cooper (Cu) filtration in dose and image quality in a Computed Radiography system.

The influence of number of counts in the myocardium in the determination of reproducible functional parameters in gated-SPECT studies simulated with GATE

Myocardial perfusion gated-single photon emission computed tomography (gated-SPECT) imaging is used for the combined evaluation of myocardial perfusion and left ventricular (LV) function. The aim of this study is to analyze the influence of counts/pixel and concomitantly the total counts in the myocardium for the calculation of myocardial functional parameters. Material and methods: Gated-SPECT studies were performed using a Monte Carlo GATE simulation package and the NCAT phantom. The simulations of these studies use the radiopharmaceutical 99mTc-labeled tracers (250, 350, 450 and 680MBq) for standard patient types, effectively corresponding to the following activities of myocardium: 3, 4.2, 5.4-8.2MBq. All studies were simulated using 15 and 30s/projection. The simulated data were reconstructed and processed by quantitative-gated-SPECT software, and the analysis of functional parameters in gated-SPECT images was done by using Bland-Altman test and Mann-Whitney-Wilcoxon test. Results: In studies simulated using different times (15 and 30s/projection), it was noted that for the activities for full body: 250 and 350MBq, there were statistically significant differences in parameters Motility and Thickness. For the left ventricular ejection fraction (LVEF), end-systolic volume (ESV) it was only for 250MBq, and 350MBq in the end-diastolic volume (EDV), while the simulated studies with 450 and 680MBq showed no statistically significant differences for global functional parameters: LVEF, EDV and ESV. Conclusion: The number of counts/pixel and, concomitantly, the total counts per simulation do not significantly interfere with the determination of gated-SPECT functional parameters, when using the administered average activity of 450MBq, corresponding to the 5.4MBq of the myocardium, for standard patient types.

Influence of the cohesive law parameters on the strength prediction of adhesively-bonded joints

Adhesive joints are largely employed nowadays as a fast and effective joining process. The respective techniques for strength prediction have also improved over the years. Cohesive Zone Models (CZM’s) coupled to Finite Element Method (FEM) analyses surpass the limitations of stress and fracture criteria and allow modelling damage. CZM’s require the energy release rates in tension (Gn) and shear (Gs) and respective fracture energies in tension (Gnc) and shear (Gsc). Additionally, the cohesive strengths (tn0 for tension and ts0 for shear) must also be defined. In this work, the influence of the CZM parameters of a triangular CZM used to model a thin adhesive layer is studied, to estimate their effect on the predictions. Some conclusions were drawn for the accuracy of the simulation results by variations of each one of these parameters.