Principles of urethane foam roof application /

"Sponsor: Naval Facilities Engineering Command."

Design of the foam in place splint,

Mode of access: Internet.

Letters from high latitudes; being some account of a voyage in 1856 in the schooner yacht "Foam" to Iceland, Jan Meyen, and Spitzbergen;

Mode of access: Internet.

Urea formaldehyde foam insulation.

Cover title.

Operator and organizational maintenance manual for truck, fire fighting, powered pumper, foam and water ... Engineered Devices Inc. model 0814, ESN 4210-150-1426.

Includes index.

Organizational maintenance repair parts and special tools list : truck, fire fighting: power pumper, foam and water, 750 gallons per minute capacity, centrifugal pump power take-off driven, 400 gallon water tank; 40 gallon foam chemical tank, class 530C, Engineered Devices Inc. MDL 0814, NSN 4210-00-150-1426 ....

Includes index.

Operator and organizational maintenance manual : truck, fire fighting, powered pumper, foam and water, 500 gallons per minute capacity, centrifugal pump, power takeoff driven, 400 gallon water tank, 40 gallon foam chemical tank, class 530B, nonwinterized ....

"May 1968."

South sea foam; the romantic adventures of a modern Don Quixote in the southern seas,

Mode of access: Internet.

Bounding the stability and rupture condition of emulsion and foam films

A scaling law is presented that provides a complete solution to the equations bounding the stability and rupture of thin films. The scaling law depends on the fundamental physicochemical properties of the film and interface to calculate bounds for the critical thickness and other key film thicknesses, the relevant waveforms associated with instability and rupture, and film lifetimes. Critical thicknesses calculated from the scaling law are shown to bound the values reported in the literature for numerous emulsion and foam films. The majority of critical thickness values are between 15 to 40% lower than the upper bound critical thickness provided by the scaling law.

Bioactive glass sol-gel foam scaffolds:evolution of nanoporosity during processing and in situ monitoring of apatite layer formation using small- and wide-angle X-ray scattering

Recent work has highlighted the potential of sol-gel-derived calcium silicate glasses for the regeneration or replacement of damaged bone tissue. The work presented herein provides new insight into the processing of bioactive calcia-silica sol-gel foams, and the reaction mechanisms associated with them when immersed in vitro in a simulated body fluid (SBF). Small-angle X-ray scattering and wide-angle X-ray scattering (diffraction) have been used to study the stabilization of these foams via heat treatment, with analogous in situ time-resolved data being gathered for a foam immersed in SBF. During thermal processing, pore sizes have been identified in the range of 16.5-62.0 nm and are only present once foams have been heated to 400 degrees C and above. Calcium nitrate crystallites were present until foams were heated to 600 degrees C; the crystallite size varied from 75 to 145 nm and increased in size with heat treatment up to 300 degrees C, then decreased in size down to 95 rim at 400 degrees C. The in situ time-resolved data show that the average pore diameter decreases as a function of immersion time in SBF, as calcium phosphates grow on the glass surfaces. Over the same time, Bragg peaks indicative of tricalcium phosphate were evident after only 1-h immersion time, and later, hydroxycarbonate apatite was also seen. The hydroxycarbonate apatite appears to have preferred orientation in the (h,k,0) direction.

The effects of foam rolling on muscular co-activation around the knee joint

The major objectives of this thesis were to determine if foam rolling had any effect on antagonist muscle activation and whether those changes would alter muscular co-activation patterns. The results from this thesis along with current literature will help clinicians to develop adequate exercise prescription for rehabilitative and pre-activity purposes. The existing literature has shown that foam rolling or roller massagers can increase range of motion (ROM), improve performance, and alter pain perception, however little research exists regarding changes in muscle activation following foam rolling. This study developed a reliable method for measuring muscle activation around the knee joint and using that method found that foam rolling the quadriceps can impair hamstrings muscle activation likely due to greater levels of perceived pain when rolling the quadriceps.

Spacetime foam induced collective bundling of intense fields

This research is supported by the Carnegie Trust for the Universities of Scotland (TO) and by the EPSRC GG-Top Project and the Cruickshank Trust (CW).

Assessing charge contribution from thermally treated Ni foam as current collectors for Li-ion batteries

In this report we have investigated the use of Ni foam substrates as anode current collectors for Li-ion batteries. As the majority of reports in the literature focus on hydrothermal formation of materials on Ni foam followed by a high temperature anneal/oxidation step, we probed the fundamental electrochemical responses of as received Ni foam substrates and those subjected to heating at 100°C, 300°C and 450°C. Through cyclic voltammetry and galvanostatic testing, it is shown that the as received and 100°C annealed Ni foam show negligible electrochemical activity. However, Ni foams heated to higher temperature showed substantial electrochemical contributions which may lead to inflated capacities and incorrect interpretations of CV responses for samples subjected to high temperature anneals. XRD, XPS and SEM analyses clearly illustrate that the formation of electrochemically active NiO nanoparticles on the surface of the foam is responsible for this behavior. To further investigate the contribution of the oxidized Ni foam to the overall electrochemical response, we formed Co3O4 nanoflowers directly on Ni foam at 450°C and showed that the resulting electrochemical response was dominated by NiO after the first 10 charge/discharge cycles. This report highlights the importance of assessing current collector activity for active materials grown on transition metal foam current collectors for Li-ion applications.