Automation Concept for Electrically Excited LV Synchronous Motor: Implementation into AC500 Programmable Logic Environment

This bachelor’s thesis is a part of the research project realized in the summer 2011 in Lappeenranta University of Technology. The goal of the project was to develop an automation concept for controlling the electrically excited synchronous motor. Thesis concentrates on the implementation of the automation concept into the ABB’s AC500 programmable logic enviroment. The automation program was developed as a state machine with the ABB’s PS501 Control Builder software. For controlling the automation program is developed a fieldbus control and with CodeSys Visualization Tool a local control with control panel. The fieldbus control is done to correspond the ABB drives communication profile and the local control is implemented with a function block which feeds right control words into the statemachine. A field current control of the synchronous motor is realized as a method presented in doctoral thesis of Olli Pyrhönen (Pyrhönen 1998). The Method combines stator flux and torque based openloop control and power factor based feedback control.

Groundwater recharge estimate at Alto Rio Grande - MG watershed

Springs are outcrops of aquifers surface, and the water cycle in this environment pass through the recharge, generally defined as the amount of water added to the aquifer, which may occur locally from rainwater infiltration. This study uses the Water Table Fluctuation (WTF) method to estimate the direct recharge and a groundwater balance to estimate the deep recharge on unconfined aquifers. The WTF method employs data of the aquifer water levels and its specific yield to estimate the direct recharge. The groundwater balance considers the direct recharge estimated by the WTF method, as the water input in the system and outputs as the base flow and deep recharge. The recharge was estimated at four areas at the watershed of Alto Rio Grande city, Minas Gerais (MG) state, in Brazil. The direct recharge estimate was 121.11; 64.62; 83.99; 152.46 (mm/year) for the L1, L2, M1 and M2 areas. The effect of the presence of forest in the recharge area can prevail over slope of relief, allowing more direct recharge, even in sources with steeper relief. The runoff from the springs in the study period exceeded the direct recharge, indicating a situation in which the saturated zone feeds the vadose zone. The annual flow was above the direct recharge pointing a situation of over exploitation of the aquifer, a non sustainable situation. The specific yield of the aquifers could also have been underestimated.

Hematological profile of Chelonia mydas (Testudines, Cheloniidae) according to the severity of fibropapillomatosis or its absence

The green turtle Chelonia mydas feeds and nests in the Brazilian coastal area and is considered an endangered species by the World Conservation Union (IUCN 2009) and threatened by the Red List of Brazilian Fauna (Ministério do Meio Ambiente 2009). Fibropapillomatosis is a disease characterized by benign skin tumors (fibropapillomas), and it is one of the main threats to the survival of this species. Studies suggest the involvement of viruses as infectious agents associated with environmental and genetic factors. Blood samples were collected from 45 turtles captured in the coastal area of the state of Sao Paulo, Brazil. From these, 27 were affected by fibropapillomas and 18 were tumor free. Biometrical data on the turtles, size, location and quantity of tumors were recorded. The area occupied by fibropapillomas per animal was calculated and four groups were determined according to severity of the disease or its absence. The objective of the study was to compare hemogram results of the sea turtles classified in these four groups. The lowest hematocrit value was observed in severely affected animals. In the hemoglobin assay, the highest value was observed in the group of tumor free turtles and the lowest, in animals severely affected. Lymphocyte counts and curved carapace length were on the verge of statistical significance.

Influence of Cutting Conditions on Tool Life, Tool Wear and Surface Finish in the Face Milling Process

The main goal of this work is to study the influence of cutting conditions - cutting speed, feed velocity and feed per tooth - on tool life and surface finish of the workpiece in the face milling of flat surfaces. Aiming to achieve this goal, several milling experiments were carried out with different cutting speeds, feed velocities and feeds per tooth. In the first phase of the experiments, cutting speed was varied without varying feed velocity, which caused a variation in feed per tooth. In the second phase of the experiments, cutting speed and feed velocity were varied in such a way that feed per tooth was kept constant. Tool flank wear and surface roughness of the workpiece were measured as cutting time elapsed. The main conclusions of this work are that a) cutting speed has a strong influence on tool life, regardless of whether feed velocity or feed per tooth varies and b) an increase in surface roughness of the workpiece is not closely related to an increase in wear of the primary cutting edge.

A meta-analysis of probiotics for preventing necrotizing enterocolitis in preterm neonates

Necrotizing enterocolitis (NEC) is one of the most common acquired diseases of the gastrointestinal tract in preterm infants. Some randomized, controlled trials (RCTs) have indicated that probiotics may potentially lower the incidence of NEC and mortality. However, debate still remains about the safety of probiotics and their influence on normal infant growth. We performed this meta-analysis to assess the safety and benefits of probiotic supplementation in preterm infants. We searched in PubMed, Embase, and Cochrane databases for English references, and in Wanfang, VIP, and CNKI databases for Chinese references. Ultimately, 27 RCTs (including 9 Chinese articles) were incorporated into this meta-analysis. Relative risk (RR) and weighted mean difference (WMD) were calculated using a random-effects or fixed-effects model, depending on the data type and heterogeneity. A total of 6655 preterm infants, including the probiotic group (n=3298) and the placebo group (n=3357), were eligible for inclusion in this meta-analysis. For Bell stage ≥I and gestational age <37 weeks, risk of NEC incidence was significantly lower in the probiotic group [RR=0.35, 95% confidence interval (CI)=0.27-0.44, P<0.00001]. For Bell stage ≥II or gestational age <34 weeks, there were likewise significant differences between the probiotic and placebo groups concerning NEC incidence (RR=0.34, 95%CI=0.25-0.48, P<0.00001; and RR=0.39, 95%CI=0.27-0.56, P<0.00001). Risk of death was significantly reduced in the probiotic group (RR=0.58, 95%CI=0.46-0.75, P<0.0001). In contrast, there was no significant difference concerning the risk of sepsis (RR=0.94, 95%CI=0.83-1.06, P=0.31). With respect to weight gain and the age at which infants reached full feeds, no significant differences were found between the probiotic and placebo groups (WMD=1.07, 95%CI=−0.21-2.34, P=0.10; and WMD=−1.66, 95%CI=−3.6-0.27, P=0.09). This meta-analysis has shown that, regardless of gestational age and NEC stage, probiotic supplementation could significantly reduce the risk of NEC in preterm infants. Analysis also indicated that such supplementation did not increase the incidence risk of sepsis or of mortality. Finally, the study showed that probiotic supplementation may have no adverse effect on normal feeding and growth.

Aflatoxin M1 in samples of "minas" cheese commercialized in the city of Belo Horizonte - Minas Gerais/Brazil

Milk products such as cheeses may be contaminated by aflatoxin M1 when dairy cattle have consumed feeds contaminated with aflatoxin B1. Samples of "Minas" cheeses (fresh, canastra and standard) were collected by the Inspection Service in the Mercado Central in Belo Horizonte city, Minas Gerais - Brazil. A purified extract was obtained by extraction with dichloromethane followed by a washing with n-hexane and immunoaffinity column purification. The quantification of aflatoxin M1 was done by high performance liquid chromatography (HPLC) using a fluorescence detector. Recoveries were about 75%. In 56 of the 75 samples (74.7%), the presence of aflatoxin M1 was detected in concentrations ranging between 0.02 and 6.92ng/g of cheese. In the positive cases ( > or = 0.02ng/g) the mean contamination level of aflatoxin M1 was 0.08ng/g in fresh cheese, 0.36ng/g in canastra cheese and 0.62ng/g in standard cheese. No aflatoxin M1 maximum tolerance level in cheese has been established in Brazil.

Functional characterization of acetylated Brazil nut (Bertholletia excelsa HBK) kernel globulin

Defatted Brazil nut kernel flour, a rich source of high quality proteins, is presently being utilized in the formulation of animal feeds. One of the possible ways to improve its utilization for human consumption is through improvement in its functional properties. In the present study, changes in some of the functional properties of Brazil nut kernel globulin were evaluated after acetylation at 58.6, 66.2 and 75.3% levels. The solubility of acetylated globulin was improved above pH 6.0 but was reduced in the pH range of 3.0-4.0. Water and oil absorption capacity, as well as the viscosity increased with increase in the level of acetylation. Level of modification also influenced the emulsifying capacity: decreased at pH 3.0, but increased at pH 7.0 and 9.0. Highest emulsion activity (approximately 62.2%) was observed at pH 3.0 followed by pH 9.0 and pH 7.0 and least (about 11.8%) at pH 5.0. Emulsion stability also followed similar behavior as that of emulsion activity.

Accelerating food safety and quality control: The use of antibody engineering techniques in the detec-tion of low-molecular weight food contaminants

The increased awareness and evolved consumer habits have set more demanding standards for the quality and safety control of food products. The production of foodstuffs which fulfill these standards can be hampered by different low-molecular weight contaminants. Such compounds can consist of, for example residues of antibiotics in animal use or mycotoxins. The extremely small size of the compounds has hindered the development of analytical methods suitable for routine use, and the methods currently in use require expensive instrumentation and qualified personnel to operate them. There is a need for new, cost-efficient and simple assay concepts which can be used for field testing and are capable of processing large sample quantities rapidly. Immunoassays have been considered as the golden standard for such rapid on-site screening methods. The introduction of directed antibody engineering and in vitro display technologies has facilitated the development of novel antibody based methods for the detection of low-molecular weight food contaminants. The primary aim of this study was to generate and engineer antibodies against low-molecular weight compounds found in various foodstuffs. The three antigen groups selected as targets of antibody development cause food safety and quality defects in wide range of products: 1) fluoroquinolones: a family of synthetic broad-spectrum antibacterial drugs used to treat wide range of human and animal infections, 2) deoxynivalenol: type B trichothecene mycotoxin, a widely recognized problem for crops and animal feeds globally, and 3) skatole, or 3-methyindole is one of the two compounds responsible for boar taint, found in the meat of monogastric animals. This study describes the generation and engineering of antibodies with versatile binding properties against low-molecular weight food contaminants, and the consecutive development of immunoassays for the detection of the respective compounds.

The contagion effect of public debt on monetary policy: the Brazilian experience

This paper attempts to explain why the Brazilian inter-bank interest rate is so high compared with rates practiced by other emerging economies. The interplay between the markets for bank reserves and government securities feeds into the inter-bank rate the risk premium of the Brazilian public debt.

Foraging ecology and parental behaviour in the common tern (Sterna hirundo)

One component of successful parenting is related to efficiency in foraging behaviour. The relationships among chick feeding, the size and type of food package, and length of parental foraging trips has not been well studied in seabirds. In addition, relatively few data have been collected on the activities of seabirds when foraging away from the nest site. The objectives of this study were: (1) to contrast productivity, feeding rate, and attendance patterns of individuals carrying a novel transmitter with a control group of birds; (2) to use radio-telemetry to assess the variability in foraging locations within and between individual male Common Terns; (3) to determine the seasonal variation in chick diet; (4) to determine for each transmittered bird, the relationships among the foraging patterns, parental behaviour, and seasonal reproductive success. The study took place over two years (1990-91) on a concrete breakwater 1 km offshore on Lake Erie near Port Colbome, Ontario. Ten pairs of terns in 1990 and 12 pairs in 1991 were radio-tracked by boat or car during the chick rearing stage. Concurrent behavioural observations documented the time each sex spent foraging or at the nest. The frequency and prey species composition of feeds to chicks were also recorded. The transmitters had negligible effects on the feeding frequency and brood attendance patterns of transmitter carrying birds. Peak nesting transmittered birds in 1990 and 1991 exhibited some inter-individual variability in foraging locations, however intraindividual variability was low. Birds foraged primarily to the west and northwest of the colony. Late nesters exhibited greater inter-individual variability, however intra-individual variability remained low for most birds. Neither group demonstrated sufficient variability to support the regular use of this colony as an "information centre". Individual transmittered birds had unique and predictable foraging patterns, and corresponding differences in feeding frequencies and brood attendance patterns, yet productivity was essentially equal between nests due to the impact and importance of stochastic events. Individuals that were recaptured in 1991 exhibited very similar foraging patterns to 1990, suggesting littie variability between years. Conservation of foraging patterns between years may have potential implications for mate choice decisions in future breeding seasons. Prey species delivered to chicks differed between morning and evening for peak and late nesters in 1990, but not 1991. Peak nesters in 1990 fed significantiy more Rainbow Smelt fOsmerus mordM) than Emerald Shiner (Notropis atherinoidesV this trend was reversed for late nesters who also fed large numbers of unidentified larval fish. No significant differences were found in 1991. Seasonal changes in prey species delivered to chicks is believed to be attributable to the temperature tolerances of the smelt and shiners, and the presence of large schools of larval fish during the late nesting season.

Analysis of the feeding behaviour of the mosquito Culex pipiens L. (Diptera: Culicidae) in relation to West Nile virus

The goal ofthis literature review is to inform the reader on several aspects of West Nile Virus (WNV) transmission by its mosquito vector, Culex pipiens and to elucidate how Cx. pipiens and WNV are intertwined. The first few sections of the literature review describe the life cycle and blood feeding behaviours ofmosquitoes so that baseline data ofmosquito biology are established. In addition to explaining how and why a mosquito blood feeds, the section on "Blood Meal Analysis" describes the different methods for determining the vertebrate source of mosquito blood meals and a brief history of these testing methods. Since this thesis looks at the feeding behaviour of Cx. pipiens, it is important to know how to determine what they are feeding upon. Discussion on other mosquito-borne diseases related to WNV gives a broader perspective to the thesis, and examines other diseases that have occurred in Ontario in the past. This is followed by background information on WNV and theories on how this virus came to North America and how it relates to Cx. pipiens. The final sections discuss Cx. pipiens and give background information to how this species of mosquito exists and behaves within North America.

Mechanisms for sustainable accountability : a case study of a nonprofit educational organization

A qualitative case study of the capacity to be accountable in one nonprofit intennediary educational organization yielded an emergent conceptual framework of four mechanisms: structural, governing, communicative, and educative mechanisms to build and sustain the capacity of accountability. Drawing attention to the purposeful creation of structures that support accountability, purposeful navigation of the complex matrix of accountability relationships, and purposeful transfer of knowledge to infonn future accountability, this study calls for mindfulness in practice in broader educational contexts. Protocols to pass on knowledge gained in building the four capacities reveal a new dimension of accountability: continuity. In this model, the educative mechanism is the life force that feeds the other three mechanisms to increase accountability and sustain it over time.

Feeding and oviposition preferences of the diamondback moth Plutella xylostella (Lepidoptera: Plutellidae) on six Brassicaceae host plant species

Plutella xylostella (diamondback moth, DBM) is a globally distributed Lepidopteran that feeds and oviposits almost exclusively on plants in the Brassicaceae family. DBM disperses from the southern United States and Mexico into Canada in the spring and summer. Establishment of DBM in Ontario is partially dependent upon the quantity and quality of host plants available and the preference of DBM for different hosts. Host plants include many crops such as broccoli, canola and cabbage, as well as landscape ornamentals and wild plants. It has previously been established that DBM are attracted to host plants by chemicals, specifically glucosinolates. I examined the preference of DBM among crop, wild and ornamental host plant species and how preference varies with insect life stage (3rd and 4th instar larvae and adults). Experiments included exposing DBM larvae from five populations coming from different locations in Canada to six Brassicaceae species and evaluating the preferences and weight gain over one hour. Then adult females were exposed to these same plant species and their oviposition preferences were examined. Populations from Alberta, Saskatchewan and Ontario were compared to assess differences in preference associated with geographic region or species of host plant. The ultimate goal of my study was to understand the potential of various Brassicaceae species to act as reservoirs to sustain and promote population growth of DBM, as well as sinks that may decrease DBM abundance. Results showed that garden cress (Lepidium sativum) was highly preferred over other species (wintercress, black mustard, aubretia, broccoli and ornamental kale) for both food and oviposition sources. Previous studies report that garden cress contains saponins, chemicals shown to be toxic to developing DBM larvae, however no studies have yet shown a preference for garden cress. These results provide information on a novel host plant with the potential to control DBM population growth. No difference in preferences was found among populations of DBM from various sources in Canada.

Photograph - Elderly Woman feeding Chickens

A photograph of an elderly woman in a field behind a home or barn. She is wearing a polka dot dress and apron as she feeds the chickens

Bâtir des territoires cultuels pour construire des identités

Le théologien protestant Olivier Bauer réfléchit sur la manière dont les actions liturgiques bâtissent des espaces cultuels et sur les identités qu’elles construisent ainsi. Ses réflexions sont nourries par son expérience des cultes sur 3 continents, en Europe, en Océanie et en Amérique du Nord. Dans une première partie, il détaille ce que font les officiants et les célébrants – célébrer, regarder, bouger, écouter, s’exprimer, toucher, manger, sentir… – pour faire apparaître les représentations de l’espace cultuel qu’elles créent. Dans une seconde partie, il met en évidence les conséquences de l’aménagement d’un territoire cultuel sur l’identité religieuse de celles et ceux qui le fréquentent : sur leurs relations à Dieu, à l’Église et au culte lui-même.