Design and performance of a complex-coupled DFB laser with sampled grating

A complex-coupled DFB laser with sampled grating has been designed and fabricated. The method uses the + 1 st order reflection of the sampled grating for laser single-mode operation. The typical threshold current of the sampled grating based DFB laser is 25 mA, and the optical output is about 10 mW at the injected current of 100 mA. The lasing wavelength of the device is 1.5385μm, which is the +1 st order wavelength of the sampled grating.

Design and Fabrication of Power Si1-xGex/Si Heterojunction Bipolar Transistor for Wireless Power Amplifier Applications

A multi-finger structure power SiGe HBT device （with an emitter area of about 166μm^2） is fabricated with very simple 2μm double-mesa technology. The DC current gain β is 144.25. The B-C junction breakdown voltage reaches 9V with a collector doping concentration of 1 × 10^17cm^-3 and a collector thickness of 400nm. Though our data are influenced by large additional RF probe pads, the device exhibits a maximum oscillation frequency fmax of 10.1GHz and a cut-off frequency fτ of 1.8GHz at a DC bias point of IC=10mA and VCE = 2.5V.

Design and numerical analysis for low birefringence silica on silicon waveguides

A new fabrication technology for three-dimensionally buried silica on silicon optical waveguide based on deep etching and thermal oxidation is presented. Using this method, a silicon layer is left at the side of waveguide. The stress distribution and effective refractive index are calculated by using finite element method and finite different beam propagation method, respectively. The results indicate that the stress of silica on silicon optical waveguide fabricated by this method can be matched in parallel and vertical directions and stress birefringence can be effectively reduced due to the side-silicon layer.

Design and analysis of kinetic energy recovery system for automobiles: a case study for commuters in Edinburgh.

Transport and its energetic and environmental impacts affect our daily lives. The transport sector is the backbone of the United Kingdom’s economy with 2.3 million people being employed in this sector. With a high dependency on transport for passengers and freight and with the knowledge that oil reserves are rapidly decreasing a solution has to be identified for conserving fuel. Passenger vehicles account for 61% of the transport fuel consumed in the U.K. and should be seen as a key area to tackle. Despite the introduction and development of electric powered cars, the widespread infrastructure that is required is not in place and has attributed to their slow uptake, as well as the fact that the electric car’s performance is not yet comparable with the conventional internal combustion engine. The benefits of the introduction of kinetic energy recovery systems to be used in conjunction with internal combustion engines and designed such that the system could easily be fitted into future passenger vehicles are examined. In this article, a review of automobile kinetic energy recovery system is presented. It has been argued that the ultracapacitor technology offers a sustainable solution. An optimum design for the urban driving cycle experienced in the city of Edinburgh has been introduced. The potential for fuel savings is also presented

Design and implementation of the embedded capacitance layers for decoupling of wireless sensor nodes

In this paper, the embedded capacitance material (ECM) is fabricated between the power and ground layers of the wireless sensor nodes, forming an integrated capacitance to replace the large amount of decoupling capacitors on the board. The ECM material, whose dielectric constant is 16, has the same size of the wireless sensor nodes of 3cm*3cm, with a thickness of only 14μm. Though the capacitance of a single ECM layer being only around 8nF, there are two reasons the ECM layers can still replace the high frequency decoupling capacitors (100nF in our case) on the board. The first reason is: the parasitic inductance of the ECM layer is much lower than the surface mount capacitors'. A smaller capacitance value of the ECM layer could achieve the same resonant frequency of the surface mount decoupling capacitors. Simulation and measurement fit this assumption well. The second reason is: more than one layer of ECM material are utilized during the design step to get a parallel connection of the several ECM capacitance layers, finally leading to a larger value of the capacitance and smaller value of parasitic. Characterization of the ECM is carried out by the LCR meter. To evaluate the behaviors of the ECM layer, time and frequency domain measurements are performed on the power-bus decoupling of the wireless sensor nodes. Comparison with the measurements of bare PCB board and decoupling capacitors solution are provided to show the improvement of the ECM layer. Measurements show that the implementation of the ECM layer can not only save the space of the surface mount decoupling capacitors, but also provide better power-bus decoupling to the nodes.

Design and evaluation of novel microencapsulation technologies to enhance delivery of Ciclosporin

Drug delivery systems influence the various processes of release, absorption, distribution and elimination of drug. Conventional delivery methods administer drug through the mouth, the skin, transmucosal areas, inhalation or injection. However, one of the current challenges is the lack of effective and targeted oral drug administration. Development of sophisticated strategies, such as micro- and nanotechnology that can integrate the design and synthesis of drug delivery systems in a one-step, scalable process is fundamental in advancing the limitations of conventional processing techniques. Thus, the objective of this thesis is to evaluate novel microencapsulation technologies in the production of size-specific and target-specific drug-loaded particles. The first part of this thesis describes the utility of PDMS and silicon microfluidic flow focusing devices (MFFDs) to produce PLGA-based microparticles. The formation of uniform droplets was dependent on the surface of PDMS remaining hydrophilic. However, the durability of PDMS was limited to no more than 1 hour before wetting of the microchannel walls with dichloromethane and subsequent swelling occurred. Critically, silicon MFFDs revealed very good solvent compatibility and was sufficiently robust to withstand elevated fluid flow rates. Silicon MFFDs facilitated experiments to run over days with continuous use and re-use of the device with a narrower microparticle size distribution, relative to conventional production techniques. The second part of this thesis demonstrates an alternative microencapsulation technology, SmPill® minispheres, to target CsA delivery to the colon. Characterisation of CsA release in vitro and in vivo was performed. By modulating the ethylcellulose:pectin coating thickness, release of CsA in-vivo was more effectively controlled compared to current commercial CsA formulations and demonstrated a linear in-vitro in-vivo relationship. Coated minispheres were shown to limit CsA release in the upper small intestine and enhance localised CsA delivery to the colon.

Adaptive intervention design in mobile health: Intervention design and development in the Cell Phone Intervention for You trial.

BACKGROUND/AIMS: The obesity epidemic has spread to young adults, and obesity is a significant risk factor for cardiovascular disease. The prominence and increasing functionality of mobile phones may provide an opportunity to deliver longitudinal and scalable weight management interventions in young adults. The aim of this article is to describe the design and development of the intervention tested in the Cell Phone Intervention for You study and to highlight the importance of adaptive intervention design that made it possible. The Cell Phone Intervention for You study was a National Heart, Lung, and Blood Institute-sponsored, controlled, 24-month randomized clinical trial comparing two active interventions to a usual-care control group. Participants were 365 overweight or obese (body mass index≥25 kg/m2) young adults. METHODS: Both active interventions were designed based on social cognitive theory and incorporated techniques for behavioral self-management and motivational enhancement. Initial intervention development occurred during a 1-year formative phase utilizing focus groups and iterative, participatory design. During the intervention testing, adaptive intervention design, where an intervention is updated or extended throughout a trial while assuring the delivery of exactly the same intervention to each cohort, was employed. The adaptive intervention design strategy distributed technical work and allowed introduction of novel components in phases intended to help promote and sustain participant engagement. Adaptive intervention design was made possible by exploiting the mobile phone's remote data capabilities so that adoption of particular application components could be continuously monitored and components subsequently added or updated remotely. RESULTS: The cell phone intervention was delivered almost entirely via cell phone and was always-present, proactive, and interactive-providing passive and active reminders, frequent opportunities for knowledge dissemination, and multiple tools for self-tracking and receiving tailored feedback. The intervention changed over 2 years to promote and sustain engagement. The personal coaching intervention, alternatively, was primarily personal coaching with trained coaches based on a proven intervention, enhanced with a mobile application, but where all interactions with the technology were participant-initiated. CONCLUSION: The complexity and length of the technology-based randomized clinical trial created challenges in engagement and technology adaptation, which were generally discovered using novel remote monitoring technology and addressed using the adaptive intervention design. Investigators should plan to develop tools and procedures that explicitly support continuous remote monitoring of interventions to support adaptive intervention design in long-term, technology-based studies, as well as developing the interventions themselves.

Special issue on design and programming of signal processors for multimedia communication:Special issue on design and programming of signal processors for multimedia communication

The technical challenges in the design and programming of signal processors for multimedia communication are discussed. The development of terminal equipment to meet such demand presents a significant technical challenge, considering that it is highly desirable that the equipment be cost effective, power efficient, versatile, and extensible for future upgrades. The main challenges in the design and programming of signal processors for multimedia communication are, general-purpose signal processor design, application-specific signal processor design, operating systems and programming support and application programming. The size of FFT is programmable so that it can be used for various OFDM-based communication systems, such as digital audio broadcasting (DAB), digital video broadcasting-terrestrial (DVB-T) and digital video broadcasting-handheld (DVB-H). The clustered architecture design and distributed ping-pong register files in the PAC DSP raise new challenges of code generation.

The design and performance of a 2.5-GHz telecommand link for wireless biomedical monitoring

This paper details the implementation and operational performance of a minimum-power 2.45-GHz pulse receiver and a companion on-off keyed transmitter for use in a semi-active duplex RF biomedical transponder. A 50-Ohm microstrip stub-matched zero-bias diode detector forms the heart of a body-worn receiver that has a CMOS baseband amplifier consuming 20 microamps from +3 V and achieves a tangential sensitivity of -53 dBm. The base transmitter generates 0.5 W of peak RF output power into 50 Ohms. Both linear and right-hand circularly polarized Tx-Rx antenna sets were employed in system reliability trials carried out in a hospital Coronary Care Unit, For transmitting antenna heights between 0.3 and 2.2 m above floor level, transponder interrogations were 95% reliable within the 67-m-sq area of the ward, falling to an average of 46 % in the surrounding rooms and corridors. Overall, the circular antenna set gave the higher reliability and lower propagation power decay index.

Design and implementation of a field programmable CRC circuit architecture

The design and implementation of a programmable cyclic redundancy check (CRC) computation circuit architecture, suitable for deployment in network related system-on-chips (SoCs) is presented. The architecture has been designed to be field reprogrammable so that it is fully flexible in terms of the polynomial deployed and the input port width. The circuit includes an embedded configuration controller that has a low reconfiguration time and hardware cost. The circuit has been synthesised and mapped to 130-nm UMC standard cell [application-specific integrated circuit (ASIC)] technology and is capable of supporting line speeds of 5 Gb/s. © 2006 IEEE.

Design and Implementation of a Measurement-Based Policy-Driven Resource Management Framework For Converged Networks

This paper presents the design and implementation of a measurement-based QoS and resource management framework, CNQF (Converged Networks’ QoS Management Framework). CNQF is designed to provide unified, scalable QoS control and resource management through the use of a policy-based network
management paradigm. It achieves this via distributed functional entities that are deployed to co-ordinate the resources of the transport network through centralized policy-driven decisions supported by measurement-based control architecture. We present the CNQF architecture, implementation of the
prototype and validation of various inbuilt QoS control mechanisms using real traffic flows on a Linux-based experimental test bed.

Dissidents with an innovation cause? Non-institutionalized actors ’ online social knowledge sharing, solution-finding tensions and technology management innovation

Purpose
– Traditionally, most studies focus on institutionalized management-driven actors to understand technology management innovation. The purpose of this paper is to argue that there is a need for research to study the nature and role of dissident non-institutionalized actors’ (i.e. outsourced web designers and rapid application software developers). The authors propose that through online social knowledge sharing, non-institutionalized actors’ solution-finding tensions enable technology management innovation.

Design/methodology/approach
– A synthesis of the literature and an analysis of the data (21 interviews) provided insights in three areas of solution-finding tensions enabling management innovation. The authors frame the analysis on the peripherally deviant work and the nature of the ways that dissident non-institutionalized actors deviate from their clients (understood as the firm) original contracted objectives.

Findings
– The findings provide insights into the productive role of solution-finding tensions in enabling opportunities for management service innovation. Furthermore, deviant practices that leverage non-institutionalized actors’ online social knowledge to fulfill customers’ requirements are not interpreted negatively, but as a positive willingness to proactively explore alternative paths.

Research limitations/implications
– The findings demonstrate the importance of dissident non-institutionalized actors in technology management innovation. However, this work is based on a single country (USA) and additional research is needed to validate and generalize the findings in other cultural and institutional settings.

Originality/value
– This paper provides new insights into the perceptions of dissident non-institutionalized actors in the practice of IT managerial decision making. The work departs from, but also extends, the previous literature, demonstrating that peripherally deviant work in solution-finding practice creates tensions, enabling management innovation between IT providers and users.

Graphic design and modernisation in Greece, 1945-1970

The primary aim of this work is to give voice to the silent history of graphic design in Greece, long uncharted and undocumented in both the international forum and the local design community. This study focuses on the professional modernisation of graphic design and its role in providing the means for change in Greek society. The research is supported by interdisciplinary analysis of commercial advertisements, posters, leaflets and magazines, as well as other supporting documentation, in the historical and cultural context of Athens, Greece from 1945 to 1970. The time examined was a transitional and vociferous period in the history of Greece, one of intense and rapid economic modernisation during the post-Second World War decades from the mid-1940s to 1970. This was a time when, along with broader changes in the social, economic and political life of Greece, important developments in design education, print technology, and professional organisation marked a new age for graphic design, as a profession emerging from the broader ‘graphic arts’ field (inclusive of both technological and creative processes) and claiming autonomy over the more established fine arts sector. All four chapters deal with modernisation in relation to the assumed divisions of traditional/modern, continuity/change, centre/periphery. Main areas of investigation are: trade organisation, graphic design education, advertising and urbanisation, electricity and tourism promotion. This research offers a view of the ways the ‘modern’ and the condition of modernity were experienced in the case of Greece through certain applications of graphic design and its agents of influence: graphic designers, artists, managers, publishers, the state and private entrepreneurs. The research benefited significantly from a number of interviews with design professionals and related individuals. The present endeavour has a modest aim: to enable understanding of how and why Greek graphic design at the time came to be, and to stress the validity of the visual as a means of historical documentation.

Efficient low-power design and implementation of IQ-imbalance compensator using early termination

In this paper, we propose a low-complexity architecture for the implementation of adaptive IQ-imbalance compensation in quadrature zero-IF receivers. Our blind IQ-compensation scheme jointly compensates for IQ phase and gain errors without the need for test/pilot tones. The proposed architecture employs early-termination of the iteration process; this enables the powering-down of the parts of the adaptive algorithm thereby saving power. The complexity, in terms of power-down efficiency is evaluated and shows a reduction by 37-50 % for 32-PSK and 37-58 % for 64-QAM modulated signals.