Subcritical crack growth and in vitro lifetime prediction of resin composites with different filler distributions

Objectives. Verify the influence of different filler distributions on the subcritical crack growth (SCG) susceptibility, Weibull parameters (m and sigma(0)) and longevity estimated by the strength-probability-time (SPT) diagram of experimental resin composites. Methods. Four composites were prepared, each one containing 59 vol% of glass powder with different filler sizes (d(50) = 0.5; 0.9; 1.2 and 1.9 mu m) and distributions. Granulometric analyses of glass powders were done by a laser diffraction particle size analyzer (Sald-7001, Shimadzu, USA). SCG parameters (n and sigma(f0)) were determined by dynamic fatigue (10(-2) to 10(2) MPa/s) using a biaxial flexural device (12 x 1.2 mm; n = 10). Twenty extra specimens of each composite were tested at 10(0) MPa/s to determine m and sigma(0). Specimens were stored in water at 37 degrees C for 24 h. Fracture surfaces were analyzed under SEM. Results. In general, the composites with broader filler distribution (C0.5 and C1.9) presented better results in terms of SCG susceptibility and longevity. C0.5 and C1.9 presented higher n values (respectively, 31.2 +/- 6.2(a) and 34.7 +/- 7.4(a)). C1.2 (166.42 +/- 0.01(a)) showed the highest and C0.5 (158.40 +/- 0.02(d)) the lowest sigma(f0) value (in MPa). Weibull parameters did not vary significantly (m: 6.6 to 10.6 and sigma(0): 170.6 to 176.4 MPa). Predicted reductions in failure stress (P-f = 5%) for a lifetime of 10 years were approximately 45% for C0.5 and C1.9 and 65% for C0.9 and C1.2. Crack propagation occurred through the polymeric matrix around the fillers and all the fracture surfaces showed brittle fracture features. Significance. Composites with broader granulometric distribution showed higher resistance to SCG and, consequently, higher longevity in vitro. (C) 2012 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Asset management of wastewater networks

Asset Management (AM) is a set of procedures operable at the strategic-tacticaloperational level, for the management of the physical asset’s performance, associated risks and costs within its whole life-cycle. AM combines the engineering, managerial and informatics points of view. In addition to internal drivers, AM is driven by the demands of customers (social pull) and regulators (environmental mandates and economic considerations). AM can follow either a top-down or a bottom-up approach. Considering rehabilitation planning at the bottom-up level, the main issue would be to rehabilitate the right pipe at the right time with the right technique. Finding the right pipe may be possible and practicable, but determining the timeliness of the rehabilitation and the choice of the techniques adopted to rehabilitate is a bit abstruse. It is a truism that rehabilitating an asset too early is unwise, just as doing it late may have entailed extra expenses en route, in addition to the cost of the exercise of rehabilitation per se. One is confronted with a typical ‘Hamlet-isque dilemma’ – ‘to repair or not to repair’; or put in another way, ‘to replace or not to replace’. The decision in this case is governed by three factors, not necessarily interrelated – quality of customer service, costs and budget in the life cycle of the asset in question. The goal of replacement planning is to find the juncture in the asset’s life cycle where the cost of replacement is balanced by the rising maintenance costs and the declining level of service. System maintenance aims at improving performance and maintaining the asset in good working condition for as long as possible. Effective planning is used to target maintenance activities to meet these goals and minimize costly exigencies. The main objective of this dissertation is to develop a process-model for asset replacement planning. The aim of the model is to determine the optimal pipe replacement year by comparing, temporally, the annual operating and maintenance costs of the existing asset and the annuity of the investment in a new equivalent pipe, at the best market price. It is proposed that risk cost provide an appropriate framework to decide the balance between investment for replacing or operational expenditures for maintaining an asset. The model describes a practical approach to estimate when an asset should be replaced. A comprehensive list of criteria to be considered is outlined, the main criteria being a visà- vis between maintenance and replacement expenditures. The costs to maintain the assets should be described by a cost function related to the asset type, the risks to the safety of people and property owing to declining condition of asset, and the predicted frequency of failures. The cost functions reflect the condition of the existing asset at the time the decision to maintain or replace is taken: age, level of deterioration, risk of failure. The process model is applied in the wastewater network of Oslo, the capital city of Norway, and uses available real-world information to forecast life-cycle costs of maintenance and rehabilitation strategies and support infrastructure management decisions. The case study provides an insight into the various definitions of ‘asset lifetime’ – service life, economic life and physical life. The results recommend that one common value for lifetime should not be applied to the all the pipelines in the stock for investment planning in the long-term period; rather it would be wiser to define different values for different cohorts of pipelines to reduce the uncertainties associated with generalisations for simplification. It is envisaged that more criteria the municipality is able to include, to estimate maintenance costs for the existing assets, the more precise will the estimation of the expected service life be. The ability to include social costs enables to compute the asset life, not only based on its physical characterisation, but also on the sensitivity of network areas to social impact of failures. The type of economic analysis is very sensitive to model parameters that are difficult to determine accurately. The main value of this approach is the effort to demonstrate that it is possible to include, in decision-making, factors as the cost of the risk associated with a decline in level of performance, the level of this deterioration and the asset’s depreciation rate, without looking at age as the sole criterion for making decisions regarding replacements.

First πK atom lifetime and πK scattering length measurements

The results of a search for hydrogen-like atoms consisting of π∓K±π∓K± mesons are presented. Evidence for πK atom production by 24 GeV/c protons from CERN PS interacting with a nickel target has been seen in terms of characteristic πK pairs from their breakup in the same target (178±49178±49) as well as in terms of produced πK atoms (653±42653±42). Using these results, the analysis yields a first value for the πK atom lifetime of View the MathML sourceτ=(2.5−1.8+3.0) fs and a first measurement of the S-wave isospin-odd πK scattering length View the MathML source|a0−|=13|a1/2−a3/2|=(0.11−0.04+0.09)Mπ−1 (aIaI for isospin I).

Value Chain Dynamics and Growth of Local Firms:The Case of Motorcycle Industry in Vietnam

Vietnam’s burgeoning market for motorcycles has attracted global industry eaders,players from developing countries, and local firms. This has led to a dynamic evolution of value chains. This paper presents an explanation of the varieties of the growth patterns xperienced by the local suppliers, focusing on the roles of customer and local supplier strategies. Case studies showed that while the role of customers may be important, strategies of suppliers to improve the ompetitive edge in the production of otorcycle components and to diversify into other products account for important ariations of growth trajectories among local suppliers. Findings presented in this paper suggest the need to direct more attention to strategy that local firms use to boost their competitive edge in business.

Some insights for a relationship marketing model integrating SERVQUAL and customer loyalty in dental clinics

The demand of new services, the emergence of new business models, insufficient innovation, underestimation of customer loyalty and reluctance to adopt new management are evidence of the deficiencies and the lack of research about the relations between patients and dental clinics. In this article we propose the structure of a model of Relationship Marketing (RM) in the dental clinic that integrates information from SERVQUAL, Customer Loyalty (CL) and activities of RM and combines the vision of dentist and patient. The first pilot study on dentists showed that: they recognize the value of maintaining better patients however they don't perform RM actions to retain them. They have databases of patients but not sophisticated enough as compared to RM tools. They perceive that the patients value "Assurance" and "Empathy" (two dimensions of service quality). Finally, they indicate that a loyal patient not necessarily pays more by the service. The proposed model will be validated using Fuzzy Logic simulation and the ultimate goal of this research line is contributing a new definition of CL.

A Quantile-Based Probabilistic Mean Value Theorem

For non-negative random variables with finite means we introduce an analogous of the equilibrium residual-lifetime distribution based on the quantile function. This allows us to construct new distributions with support (0, 1), and to obtain a new quantile-based version of the probabilistic generalization of Taylor's theorem. Similarly, for pairs of stochastically ordered random variables we come to a new quantile-based form of the probabilistic mean value theorem. The latter involves a distribution that generalizes the Lorenz curve. We investigate the special case of proportional quantile functions and apply the given results to various models based on classes of distributions and measures of risk theory. Motivated by some stochastic comparisons, we also introduce the “expected reversed proportional shortfall order”, and a new characterization of random lifetimes involving the reversed hazard rate function.

Does customer satisfaction lead to improved brand equity? An empirical examination of two categories of retail brands

Purpose – The objective of the present research is to examine the relationship between consumers' satisfaction with a retailer and the equity they associate with the retail brand. Design/methodology/approach – Retail brand equity is conceptualized as a four-dimensional construct comprising: retailer awareness, retailer associations, retailer perceived quality, and retailer loyalty. Then the associative network memory model is applied from cognitive psychology to the specific context of the relationships between customer satisfaction and consumer-based retailer equity. A survey was undertaken using a convenience sample of shopping mall consumers in an Australian state capital city. The questionnaire used to collect data included an experimental design such that two categories of retailers were included in the study: department stores and specialty stores, with three retailers representing each category. The relationship between consumer-based retailer equity and customer satisfaction was examined using multivariate analysis of variance. Findings – Results indicate that retail brand equity varies with customer satisfaction. For department stores, each consumer-based retailer equity dimension varied according to customer satisfaction with the retailer. However, for specialty stores, only three of the consumer-based retailer equity dimensions, namely retailer awareness, retailer associations and retailer perceived quality, varied according to customer satisfaction level with the retailer. Originality/value – The principal contribution of the present research is that it demonstrates empirically a positive relationship between customer satisfaction and an intangible asset such as retailer equity.

Understanding service failure and recovery: A customer-based phenomenographic approach

To date, researchers have largely considered service failure and recovery as a combination of individual constructs, often in isolation, rather than viewing failure and recovery holistically. Consequently, our understanding is fragmented. Furthermore, while some attempt has been made to gain a better understanding of service failure and recovery from both the customer and the employee’s perspective (cf. Bitner et al.1990; McColl-Kennedy and Sparks 2003), no study has employed an interpretative perspective that potentially offers a rich, in-depth approach to this important area of research. Given this gap, our paper presents the value of taking a customer-based interpretive approach to obtaining a fuller understanding of the way customers view service failure and recovery. In this paper we report the findings of our phenomenography study of twenty in-depth interviews. Not only do we argue the benefits of adopting this fresh approach to studying service failure and recovery, we also present an innovative conceptual framework derived from our phenomenographic research findings, which has significant theoretical and practical implications.

Enhancing performance through the introduction of customer orientation into the building components industry

Purpose: This paper aims to describe an investigation into how company performance can be improved by integrating internal and external customers and technology. The approach was developed, implemented and evaluated in the operations of the building components industry. The research was carried out in the precast concrete division of a Singapore company. Design/methodology/ approach: For the purpose of undertaking the investigation an exploratory case study approach was used. This was divided into conceptual and action research stages. The action research was also used to implement the changes in the company. Questionnaire surveys were carried out among company employees and external customers to assess the effect of these changes. Results of the investigation were derived using content and statistical analysis. Triangulation between three sources was used for validating the data. Findings: The exploratory case study strategy resulted in rich research data, which provided evidence of the changes taking place and integration happening, leading to improved performance. The action research approach proved a powerful tool where the uncertainty of outcomes makes it near impossible to make accurate forecasts. Another output of the research was the development of an "integrated customer orientation" (ICO) model. Research limitations/implications: The research in this paper used a single site action research investigation so should be interpreted within the specific company and industry context. There are implications for theory and practice in a number of areas of production and marketing as well as contributions to understanding about productivity improvement and organisational development. The investigation also fulfils the dual objectives of action research by contributing to both knowledge and practice. Originality/value: The paper describes a unique approach towards improving productivity, quality and service through the use of action research to implement changes, as well as providing the research evidence to evaluate both the process of implementation and results achieved. © Emerald Group Publishing Limited.

Managing the quality, value and impact of academic libraries: the role of external standards

Purpose – The purpose of this paper is to explore the role and relevance of external standards in demonstrating the value and impact of academic library services to their stakeholders. Design/methodology/approach – Two UK standards, Charter Mark and Customer Service Excellence, are evaluated via an exploratory case study, employing multiple data collection techniques. Methods and results of phases 1-2 of a three phase research project are outlined. Findings – Despite some limitations, standards may assist the manager in demonstrating the value, impact and quality of academic libraries in a recessional environment. Active engagement and partnership with customers is imperative if academic libraries are to be viewed as vital to their parent organisations and thus survive. Originality/value – This paper provides a systematic evaluation of the role of external accreditation standards in measuring academic library service value and impact.

An integrated process for strategic positioning within the value chain

The purpose of this article is to highlight the value of ‘strategic positioning’ as a means of providing competitive edge, and to introduce and describe a novel method of managing this. Strategic positioning is concerned with the choice of business activities a company carries out itself, compared to those provided by suppliers, partners, distributors and even customers. It is therefore directly impacted by, and has direct impact upon, such decisions as outsourcing, off-shoring, partnering, innovation, technology acquisition and customer servicing.

The role of the sales employee in securing customer satisfaction

Purpose: Previous research has emphasized the pivotal role that salespeople play in customer satisfaction. In this regard, the relationship between salespeople's attitudes, skills, and characteristics, and customer satisfaction remains an area of interest. The paper aims to make three contributions: first, it seeks to examine the impact of salespeople's satisfaction, adaptive selling, and dominance on customer satisfaction. Second, this research aims to use dyadic data, which is a better test of the relationships between constructs since it avoids common method variance. Finally, in contrast to previous research, it aims to test all of the customers of salespeople rather than customers selected by salespeople. Design/methodology/approach: The study employs multilevel analysis to examine the relationship between salespeople's satisfaction with the firm on customer satisfaction, using a dyadic, matched business-to-business sample of a large European financial service provider that comprises 188 customers and 18 employees. Findings: The paper finds that customers' evaluation of service quality, product quality, and value influence customer satisfaction. The analysis at the selling firm's employee level shows that adaptive selling and employee satisfaction positively impact customer satisfaction, while dominance is negatively related to customer satisfaction. Practical implications: Research shows that customer-focus is a key driver in the success of service companies. Customer satisfaction is regarded as a prerequisite for establishing long-term, profitable relations between company and customer, and customer contact employees are key to nurturing this relationship. The role of salespeople's attitudes, skills, and characteristics in the customer satisfaction process are highlighted in this paper. Originality/value: The use of dyadic, multilevel studies to assess the nature of the relationship between employees and customers is, to date, surprisingly limited. The paper examines the link between employee attitudes, skills, and characteristics, and customer satisfaction in a business-to-business setting in the financial service sector, differentiating between customer- and employee-level drivers of business customer satisfaction.

Identification and analysis of moderator variables:investigating the customer satisfaction-loyalty link

Purpose – Research on the relationship between customer satisfaction and customer loyalty has advanced to a stage that requires a more thorough examination of moderator variables. Limited research shows how moderators influence the relationship between customer satisfaction and customer loyalty in a service context; this article aims to present empirical evidence of the conditions in which the satisfaction-loyalty relationship becomes stronger or weaker. Design/methodology/approach – Using a sample of more than 700 customers of DIY retailers and multi-group structural equation modelling, the authors examine moderating effects of several firm-related variables, variables that result from firm/employee-customer interactions and individual-level variables (i.e. loyalty cards, critical incidents, customer age, gender, income, expertise). Findings – The empirical results suggest that not all of the moderators considered influence the satisfaction-loyalty link. Specifically, critical incidents and income are important moderators of the relationship between customer satisfaction and customer loyalty. Practical implications – Several of the moderator variables considered in this study are manageable variables. Originality/value – This study should prove valuable to academic researchers as well as service and retailing managers. It systematically analyses the moderating effect of firm-related and individual-level variables on the relationship between customer satisfaction and loyalty. It shows the differential effect of different types of moderator variables on the satisfaction-loyalty link.

Customer equity drivers and future sales

Research on linking operational marketing inputs to customer attitudes and customer behavior has been gaining significance concomitant with the growing recognition that customers are market-based assets. In response to this, researchers and practitioners have proposed several conceptual models. Despite recent advances in research, the results are still inconclusive as to the relationship between customer attitude and future sales. A reason for this could be due to the paucity of studies combining survey-based data with behavioral data to understand better the drivers of customer behavior. With that in mind, the authors investigate the effects of customer perceptions of key marketing actions on customer attitudes and actual customer behavior as reflected by future sales. The authors propose that customer perceptions of value, brand, and relationship—“customer equity drivers”—affect loyalty intentions and future sales. The results of the study, which is based on a sample of 5694 customers of a large European do-it-yourself retailer, suggest that customer equity drivers can significantly predict future sales, even after the authors control for the current sales level.

The impact of employees' customer orientation and service orientation behaviours on customers' service evaluation

In this paper the authors conceptualize and test the effects of service employees’ customer orientation and service orientation behaviors within an extended service evaluation model encompassing service quality, service encounter quality, perceived value and customer satisfaction. The context is 271 Indian retail customers. Data analysis incorporates confirmatory factor analysis and structural equation modeling. We find that Findings indicate that: 1) customer orientation is positively related to service orientation, customers’ perceptions of service encounter quality and service quality; 2) service orientation influences customers’ perceptions of service encounter quality and service quality; 3) customers’ perceptions of service encounter quality influence customers’ perceptions of service quality and customer satisfaction; 4) customers’ perceptions of service quality influence value perceptions; 5) service quality influences customer satisfaction; and 6) customer satisfaction influences customers’ behavioral intentions. The importance of these findings for practitioners and academics, research limitations and future research avenues are subsequently discussed.