Decomposition of corn and soybean residues under field conditions and their role as inoculum source

Necrotrophic parasites of above-ground plant parts survive saprophytically, between growing seasons in host crop residues. In an experiment conducted under field conditions, the time required in months for corn and soybean residues to be completely decomposed was quantified. Residues were laid on the soil surface to simulate no-till farming. Crop debris of the two plant species collected on the harvesting day cut into pieces of 5.0cm-long and a 200g mass was added to nylon mesh bags. At monthly intervals, bags were taken to the laboratory for weighing. Corn residues were decomposed within 37.0 months and those of soybean, within 34.5 months. Hw main necrotrophic fungi diagnosed in the corn residues were Colletotrichum gramicola, Diplodia spp. and Gibberella zeae, and those in soybeans residues were Cercospora kikuchii, Colletotrichum spp, Glomerella sp. and Phomopsis spp. Thus, those periods shoulb be observed in crop rotation aimed at to eliminating contaminated residues and, consequently, the inoculum from the cultivated area.

Effect of phytoplasma infection on the activity of peroxidase, β-1,3 glucanase and chitinase in corn plants

In the present work we studied the effect of inoculating corn plants with the maize bushy stunt phytoplasma on the activity of the enzymes peroxidase, β-1,3 glucanase and chitinase. The experiments were carried out inside a greenhouse. Plants of a resistant and a susceptible corn hybrid were inoculated by using infective Dalbulus maidis leafhoppers 10 days after sowing. When symptoms started to appear, leaf samples were collected at different periods to quantify enzyme activity. The results showed an increase in the activity of the three enzymes in inoculated plants of both hybrids. In general, the values observed for the level of the different enzymes were higher in the susceptible hybrid when compared to the resistant one. Thus, the increases in peroxidase, β-1,3 glucanase and chitinase levels in inoculated plants are evidence of changes in the host metabolism caused by the phytoplasma. On the other hand, since the increases could not be correlated with plant resistance further studies are needed to explain such changes.

Semi-selective culture medium for Exserohilum turcicum isolation from corn seeds

Northern corn leaf blight, caused by Exserohilum turcicum (Et), is a disease of widespread occurrence in regions where corn, sweetcorn and popcorn are grown. This disease has great potential to cause damage and has been studied for years, but the association of its causal agent with seeds remains unconfirmed. Thus, the availability of a sensitive method to detect and quantify the inoculum in seeds, even at low incidence, is essential. The aim of this study was to develop a method to detect and quantify the presence of the fungus infecting and infesting corn and popcorn seeds. Artificially and naturally infected seeds were employed to develop the medium. The semi-selective medium was composed of carbendazim (active ingredient) (60 mg/L), captan (30 mg/L), streptomycin sulfate (500 mg/L) and neomycin sulfate (600 mg/L) aggregated to the medium lactose casein hydrolysate agar medium. By using this, Et was detected in naturally infected corn seeds, showing 0.124% incidence, in four out of ten analyzed samples. In addition, 1.04 conidia were detected per infested seed. By means of isolation, pathogenicity test, morphological characterization and comparison with descriptions of the species in the literature, the fungus isolated from the seeds was confirmed to be Et. Both infection and infestation were considered low; thus, for studies of Et detection in corn seeds, the use of semi-selective medium and more than 1,200 seeds/sample is suggested.

Fungicide baseline for mycelial sensitivity of Exserohilum turcicum, causal agent of northern corn leaf blight

Northern corn leaf blight, caused by Exserohilum turcicum(Et), is one of the major corn diseases which can reduce grain yield and quality. The aim of this study was to determine the mycelial sensitivity of ten Etisolates, five from Argentina and five from Brazil, to six fungicides (carbendazim, captan, fludioxinil, metalaxyl, iprodione and thiram) used in seed treatment. The inhibitory concentration (IC50) was determined by using seven concentrations of the fungicides supplemented to the agar medium. The mycelial colony diameter was measured with a digital caliper. Experimental design was completely randomized with four replicates. Data on the percent mycelial growth inhibition were analyzed by logarithmic regression and the IC50 was calculated. The fungicide iprodione was the most potent, with IC50 < 0.01 mg/L, followed by fludioxonil, IC50 0.31 mg/L, and thiram, 1.37 mg/L. Carbendazim, metalaxyl and captan were classified as non-fungitoxic, showing IC50 > 50 mg/L for all isolates. Although iprodione is the most potent fungicide, it is not used for corn seed treatment. The IC50s obtained in this study can be used as baseline for future monitoring studies of Etsensitivity to fungicides.

COMPARISON BETWEEN WOOD DRYING DEFECT SCORES: SPECIMEN TESTING X ANALYSIS OF KILN-DRIED BOARDS

It is important to develop drying technologies for Eucalyptus grandis lumber, which is one of the most planted species of this genus in Brazil and plays an important role as raw material for the wood industry. The general aim of this work was to assess the conventional kiln drying of juvenile wood of three clones of Eucalyptus grandis. The specific aims were to compare the behavior between: i) drying defects indicated by tests with wood specimens and conventional kiln-dried boards; and ii) physical properties and the drying quality. Five 11-year-old trees of each clone were felled, and only flatsawn boards of the first log were used. Basic density and total shrinkage were determined, and the drying test with wood specimens at 100 °C was carried out. Kiln drying of boards was performed, and initial and final moisture content, moisture gradient in thickness, drying stresses and drying defects were assessed. The defect scoring method was used to verify the behavior between the defects detected by specimen testing and the defects detected in kiln-dried boards. As main results, the drying schedule was too severe for the wood, resulting in a high level of boards with defects. The behavior between the defects in the drying test with specimens and the defects of kiln-dried boards was different, there was no correspondence, according to the defect scoring method.

Efficiency of pneumatic and horizontal perforated disk meter mechanism in corn no-tillage seeders in soil with different mobilization reports

This work objectified to evaluate the efficiency of two meter mechanism of corn seeds when submitted to different forward speed and soil management system during the non-tillage seeding. It was used a factorial design in randomized blocks. The factors whose effects were examined were related to the seeders with pneumatic and horizontal disk meter mechanisms for the distribution of the seeds, to the set tractor-seeder forward speeds (4.4; 8.0 and 9.8 km h-1), and to the soil management system considering the corn no-tillage seeding over minimum tillage with chisel plow and the no-tillage system for the seeding of oat culture (Avena strigosa Schreb). It was verified that the forward speed didn't influence the initial and final stands of plants but it interfered in the regularity of longitudinal distribution of plants. The smallest speed provided the largest percentile of normal spacing between plants. The pneumatic meter mechanism presented better performance than the horizontal disk perforated in the longitudinal distribution of plants. About corn productivity aspect it's indifferent the recommendation of use for pneumatic and perforated horizontal disk meter mechanism of seeds.

Mathematical models to describe the volumetric shrinkage rate of red beans during drying

The present study aimed to determine the volumetric shrinkage rate of bean (Phaseolus vulgaris L.) seeds during air-drying under different conditions of air, temperature and relative humidity, and to adjust several mathematical models to the empiric values observed, and select the one that best represents the phenomenon. Six mathematical models were adjusted to the experimental values to represent the phenomenon. It was determined the degree of adjustment of each model from the value of the coefficient of determination, the behavior of the distribution of the residuals, and the magnitude of the average relative and estimated errors. The rate of volumetric shrinkage that occurred in bean seeds during drying is between 25 and 37%. It basically depends on the final moisture content, regardless of the air conditions during drying. The Modified Bala & Woods' model best represented the process.

Solar drying of jack fruit almonds

Dryers heated by solar energy have been constructed and used in drying whole and half jack fruit almonds. The samples were dried during the day in direct sun and in the conventional solar dryer prepared for this purpose. Another piece of equipment was built for reception and accumulation of sun energy in a body of water, which was used as a heat source for night drying. The drying with the sun energy was compared with artificial drying. The jack fruit almonds were dried whole, half, with pellicle and without it. The storage of solar energy in water was technically viable for use in night drying. The drying by combining solar dryers in the day and night periods were completed in approximately 35 hours, and were equivalent to artificial drying between 40ºC and 70ºC. Almond cut in half and the pellicle removed reduced the drying time.

Anaerobic biodigestion of pigs feces in the initial, growing and finishing stages fed with diets formulated with corn or sorghum

The objective of this study was to evaluate the quality and the production of biogas and biofertilizer obtained from biodigester supplied with pig feces in the initial, growing and finishing stages, fed with diets formulated based on corn or sorghum. Twenty bench biodigesters were used with hydraulic retention time of 30 days and daily loads that contained 4 to 6% of total solids (TS) and 3.6 to 5.2% of volatile solids (VS). In the effluent of the biodigesters, mean levels of TS were observed ranging between 1.6 and 2.0% and of VS between 1.2 and 1.6%. The mean reductions of TS were 57.7 to 64.7% and of VS from 61.7 to 69.0%, and there was only difference in the finishing phase, in which the major averages reductions were produced by the biodigesters supplied with feces from animals fed with diets based on corn. In biodigesters supplied with feces from animals in the initial and growing stages fed with diets based on corn, were observed higher average productions of biogas and the greatest average potentials of biogas production. The average potentials obtained were 0.033; 0.181; 0.685; 0.788 and 1.132 m³ per kg of affluent, manure, TS added, VS added and VS reduced, respectively. No differences were found on the average content of methane in the biogas between diets and stages. The average concentrations of nutrients N, P, K, Ca, Mg, Na, Fe, Mn, Zn and Cu in the biodigester affluent and effluent, ranged between diets and stages.

Emergence of corn according to the sowing depth of the seed and loads on press wheels

The seeding process was the operation that suffered the most changes in no-tillage system due the cover crop soil and new particle soil arrangement. The objective of this study was to verify the effects of loads applied to the wheels and adjustments of sowing depth on seedling emergence of corn in no-tillage system. The experimental design was completely randomized with a factorial arrangement 5x4, with five loads applied to the wheels and four theoretical sowing depth adjustments. The real sowing depth increased in the lower theoretical depth and decreased in the higher theoretical depth, due to the compaction loads. Regarding the time of emergence, loads applied had not influence at the greater depths. Emergence time decreased with the load increase in the lower depths. Thus, the adjustment of the compactor wheels can influence in the corn seeding process.

Effective diffusivity and convective mass transfer coefficient during the drying of bananas

In this article, a methodology is used for the simultaneous determination of the effective diffusivity and the convective mass transfer coefficient in porous solids, which can be considered as an infinite cylinder during drying. Two models are used for optimization and drying simulation: model 1 (constant volume and diffusivity, with equilibrium boundary condition), and model 2 (constant volume and diffusivity with convective boundary condition). Optimization algorithms based on the inverse method were coupled to the analytical solutions, and these solutions can be adjusted to experimental data of the drying kinetics. An application of optimization methodology was made to describe the drying kinetics of whole bananas, using experimental data available in the literature. The statistical indicators enable to affirm that the solution of diffusion equation with convective boundary condition generates results superior than those with the equilibrium boundary condition.

Soil sampling intensity and spatial distribution pattern of soils attributes and corn yield in no-tillage system

Taking into account that the sampling intensity of soil attributes is a determining factor for applying of concepts of precision agriculture, this study aims to determine the spatial distribution pattern of soil attributes and corn yield at four soil sampling intensities and verify how sampling intensity affects cause-effect relationship between soil attributes and corn yield. A 100-referenced point sample grid was imposed on the experimental site. Thus, each sampling cell encompassed an area of 45 m² and was composed of five 10-m long crop rows, where referenced points were considered the center of the cell. Samples were taken from at 0 to 0.1 m and 0.1 to 0.2 m depths. Soil chemical attributes and clay content were evaluated. Sampling intensities were established by initial 100-point sampling, resulting data sets of 100; 75; 50 and 25 points. The data were submitted to descriptive statistical and geostatistics analyses. The best sampling intensity to know the spatial distribution pattern was dependent on the soil attribute being studied. The attributes P and K+ content showed higher spatial variability; while the clay content, Ca2+, Mg2+ and base saturation values (V) showed lesser spatial variability. The spatial distribution pattern of clay content and V at the 100-point sampling were the ones which best explained the spatial distribution pattern of corn yield.

Comparison of metering mechanisms of corn seed

It was compared the performance of the metering mechanism of corn seeds (Zea mays) in direct seeding in an area of ​​200 ha, a property in Piraí do Sul, State of Paraná - PR, in Brazil. It was seeded 4 maize hybrids, 50 ha of each, with seeds of different sieves. The experiment was conducted in a randomized block design (RBD), with 3 treatments and 9 repetitions for each corn hybrid. The treatments were the pneumatic seed of metering mechanisms, horizontal perforated disc with and without ramp®. The plots were 40 m² and were distributed at the early, middle and late sowing. The variables analyzed in each corn hybrid were initial population, faulty spacing, multiple spacing, acceptable spacing, and yield components. As there were no significant differences in the variables, it was concluded that the quality of seeding with different systems of distribution was similar in the different sieves of distributed corn seeds.

Sowing depths of brachiaria in intercropping with corn in no tillage planting

The forage production in crop-livestock integration is critical both for formation of straw for no tillage planting and food for livestock farm. The experiment was conducted in the autumn/winter of 2009 and 2010, in the city of Selvíria -state of Mato Grosso do Sul -MS, Brazil, at Experimental Station of FEIS/UNESP. The objective was to evaluate the optimal depth for deposition of seeds of two Brachiaria species intercropped with corn with emphasis on grain yield and straw. The experimental design was a randomized block design in a factorial scheme 3 x 3, with four replications. The main treatments were two species of Brachiaria (Urochloa brizantha "Marandú" and Urochloa ruziziensis), which seeds were mixed with corn fertilizer and a control treatment (without intercropping). Secondary treatments consisted of three depths (8; 10 and 16 cm) in the deposition of fertilizer (in the consortium and the control treatments). The intercropping corn with Brachiaria produced similar amounts of straw. The straw total production was higher when intercropped and decreased with depth. The consortium with U. ruziziensis provided higher grain yield of corn in relation to U. brizantha, in 2010. The sowing depth of forages did not affect corn yield.

Energetic analysis of landrace varieties and hybrids of corn produced in different technological levels of management

The aim of this study was to analyze, under the energetic point of view, the cultivation of corn in three management systems (low, medium and high-tech), using two landrace varieties ('Argentino' and 'BR da Várzea'), a double hybrid cultivar (SHS 4080) and a simple hybrid (IAC 8333). Five performance indicators were used: energy efficiency, liquid cultural energy, cultural efficiency, energy balance and productive energy efficiency. From the perspective of family farming, it was verified the largest social importance of the systems under low and medium levels of technology, due to the increase employment capacity of rural labor. The liquid cultural energy and energy balance were more favorable for the system under high technological level, unlike cultural efficiency and productive energy efficiency, which were significantly higher for medium and low technological levels. The variety 'Argentino' showed lower productive energy efficiency. The variety 'BR da Várzea', on the other hand, presented the potential to generate energy as much as the hybrids. In general, the biggest sustainability in the corn crop was achieved when the management system under medium and lower levels of technology were used.