Pollutant emissions during pyrolysis and combustion of waste printed circuit boards, before and after metal removal

The constant increase in the production of electronic devices implies the need for an appropriate management of a growing number of waste electrical and electronic equipment. Thermal treatments represent an interesting alternative to recycle this kind of waste, but particular attention has to be paid to the potential emissions of toxic by-products. In this study, the emissions from thermal degradation of printed circuit boards (with and without metals) have been studied using a laboratory scale reactor, under oxidizing and inert atmosphere at 600 and 850 °C. Apart from carbon oxides, HBr was the main decomposition product, followed by high amounts of methane, ethylene, propylene, phenol and benzene. The maximum formation of PAHs was found in pyrolysis at 850 °C, naphthalene being the most abundant. High levels of 2-, 4-, 2,4-, 2,6- and 2,4,6-bromophenols were found, especially at 600 °C. Emissions of PCDD/Fs and dioxin-like PCBs were quite low and much lower than that of PBDD/Fs, due to the higher bromine content of the samples. Combustion at 600 °C was the run with the highest PBDD/F formation: the total content of eleven 2,3,7,8-substituted congeners (tetra- through heptaBDD/Fs) was 7240 and 3250 ng WHO2005-TEQ/kg sample, corresponding to the sample with and without metals, respectively.

Hydrogen Production by Steam Reforming of Ethanol on Rh-Pt Catalysts: Influence of CeO2, ZrO2, and La2O3 as Supports

CeO2-, ZrO2-, and La2O3-supported Rh-Pt catalysts were tested to assess their ability to catalyze the steam reforming of ethanol (SRE) for H2 production. SRE activity tests were performed using EtOH:H2O:N2 (molar ratio 1:3:51) at a gaseous space velocity of 70,600 h−1 between 400 and 700 °C at atmospheric pressure. The SRE stability of the catalysts was tested at 700 °C for 27 h time on stream under the same conditions. RhPt/CeO2, which showed the best performance in the stability test, also produced the highest H2 yield above 600 °C, followed by RhPt/La2O3 and RhPt/ZrO2. The fresh and aged catalysts were characterized by TEM, XPS, and TGA. The higher H2 selectivity of RhPt/CeO2 was ascribed to the formation of small (~5 nm) and stable particles probably consistent of Rh-Pt alloys with a Pt surface enrichment. Both metals were oxidized and acted as an almost constant active phase during the stability test owing to strong metal-support interactions, as well as the superior oxygen mobility of the support. The TGA results confirmed the absence of carbonaceous residues in all the aged catalysts.

Making Space: Feasibility of Urban Manufacturing through Shared Resources

Thesis (Master's)--University of Washington, 2016-06

The production, purification and crystallization of a pocilloporin pigment from a reef-forming coral

Reef-building corals contain fluorescent pigments termed pocilloporins that function by regulating the light environment of coral and acting as a photoprotectant in excessive sunlight. These pocilloporins are related to the monomeric green fluorescent protein and the tetrameric DsRed fluorescent proteins, which have widespread use as biotechnological tools. An intensely blue-coloured pocilloporin, termed Rtms5, was expressed in Escherichia coli, purified and crystallized. Rtms5 was shown to be tetrameric, with deep blue crystals that diffract to 2.2 Angstrom resolution and belong to space group I4(1)22. The colour of this pocilloporin was observed to be sensitive to pH and a yellow (pH 3.5) and a red form (pH 4.5) of Rtms5 were also crystallized. These crystals belong to space group P4(2)22 and diffract to 2.4 Angstrom resolution or better.

Locating whiteness in the academic production of "I Philosophy" in and of time and place

This review will critically evaluate two recent texts by white academics working across disciplines of cultural studies, history and anthropology and published by UNSW Press, which share a focus on the relationship between Aboriginality, Philosophy, Place and Time in Australia. I write from the position of a queer white academic committed to engaging politically and intellectually with the challenge of Indigenous sovereignties in this place while also aware that my position as a middle class white woman and intellectual imposes limits on what it is possible for me to know about Indigenous epistemologies (see Moreton-Robinson, 2000). In the course of this review I will demonstrate how anthropology's tendency to fix its objects of study within a circumscribed space of 'difference' limits the capacity of texts produced within this discipline to account for racialized struggles over sovereignty. While these struggles are equally embedded in the ethnographic context and the nation's constitution and political institutions, we will see that Muecke and Bird Rose confront problems in analysing the relationship between the intimate space of the 'field', in which one's research subjects quickly become one's 'friends' and/or 'classificatory kin'—on one hand—and the public space of the nation within which statements about Aboriginality by white academics circulate and are vested with an authority that escapes individual intentions and control—on the other.

Fixed wages and bonuses in agency contracts: the case of a continuous state space

In this paper, we extend the state-contingent production approach to principal–agent problems to the case where the state space is an atomless continuum. The approach is modelled on the treatment of optimal tax problems. The central observation is that, under reasonable conditions, the optimal contract may involve a fixed wage with a bonus for above-normal performance. This is analogous to the phenomenon of "bunching" at the bottom in the optimal tax literature.

Extent and economic effect of heat loads on dairy cattle production in Australia

Objective To investigate the extent of heat load problems, caused by the combination of excessive temperature and humidity, in Holstein-Friesian cows in Australia. Also, to outline how milk production losses and consequent costs from this can be estimated and minimised. Procedures Long-term meteorological data for Australia were analysed to determine the distribution of hot conditions over space and time. Fifteen dairy production regions were identified for higher-resolution data analysis. Both the raw meteorological data and their integration into a temperature-humidity thermal index were compiled onto a computer program. This mapping software displays the distribution of climatic patterns, both Australia-wide and within the selected dairying regions. Graphical displays of the variation in historical records for 200 locations in the 15 dairying regions are also available. As a separate study, production data from research stations, on-farm trials and milk factory records were statistically analysed and correlated with the climatic indices, to estimate production losses due to hot conditions. Results Both milk yields and milk constituents declined with increases in the temperature-humidity index. The onset and rate of this decline are dependent on a number of factors, including location, level of production, adaptation, and management regime. These results have been integrated into a farm-level economic analysis for managers of dairy properties. Conclusion By considering the historical patterns of hot conditions over time and space, along with expected production losses, managers of dairy farms can now conduct an economic evaluation of investment strategies to alleviate heat loads. These strategies include the provision of sprinklers, shade structures, or combinations of these.

Optimal production planning for PCB assembly

It is indisputable that printed circuit boards (PCBs) play a vital role in our daily lives. With the ever-increasing applications of PCBs, one of the crucial ways to increase a PCB manufacturer’s competitiveness in terms of operation efficiency is to minimize the production time so that the products can be introduced to the market sooner. Optimal Production Planning for PCB Assembly is the first book to focus on the optimization of the PCB assembly lines’ efficiency. This is done by: • integrating the component sequencing and the feeder arrangement problems together for both the pick-and-place machine and the chip shooter machine; • constructing mathematical models and developing an efficient and effective heuristic solution approach for the integrated problems for both types of placement machines, the line assignment problem, and the component allocation problem; and • developing a prototype of the PCB assembly planning system. The techniques proposed in Optimal Production Planning for PCB Assembly will enable process planners in the electronics manufacturing industry to improve the assembly line’s efficiency in their companies. Graduate students in operations research can familiarise themselves with the techniques and the applications of mathematical modeling after reading this advanced introduction to optimal production planning for PCB assembly.

Chemical studies of plasma etchants used in integrated circuit manufacture

Plasma or "dry" etching is an essential process for the production of modern microelectronic circuits. However, despite intensive research, many aspects of the etch process are not fully understood. The results of studies of the plasma etching of Si and Si02 in fluorine-containing discharges, and the complementary technique of plasma polymerisation are presented in this thesis. Optical emission spectroscopy with argon actinometry was used as the principle plasma diagnostic. Statistical experimental design was used to model and compare Si and Si02 etch rates in CF4 and SF6 discharges as a function of flow, pressure and power. Etch mechanisms m both systems, including the potential reduction of Si etch rates in CF4 due to fluorocarbon polymer formation, are discussed. Si etch rates in CF4 /SF6 mixtures were successfully accounted for by the models produced. Si etch rates in CF4/C2F6 and CHF3 as a function of the addition of oxygen-containing additives (02, N20 and CO2) are shown to be consistent with a simple competition between F, 0 and CFx species for Si surface sites. For the range of conditions studied, Si02 etch rates were not dependent on F-atom concentration, but the presence of fluorine was essential in order to achieve significant etch rates. The influence of a wide range of electrode materials on the etch rate of Si and Si02 in CF4 and CF4 /02 plasmas was studied. It was found that the Si etch rate in a CF4 plasma was considerably enhanced, relative to an anodised aluminium electrode, in the presence of soda glass or sodium or potassium "doped" quartz. The effect was even more pronounced in a CF4 /02 discharge. In the latter system lead and copper electrodes also enhanced the Si etch rate. These results could not be accounted for by a corresponding rise in atomic fluorine concentration. Three possible etch enhancement mechanisms are discussed. Fluorocarbon polymer deposition was studied, both because of its relevance to etch mechanisms and its intrinsic interest, as a function of fluorocarbon source gas (CF4, C2F6, C3F8 and CHF3), process time, RF power and percentage hydrogen addition. Gas phase concentrations of F, H and CF2 were measured by optical emission spectroscopy, and the resultant polymer structure determined by X-ray photoelectron spectroscopy and infrared spectroscopy. Thermal and electrical properties were measured also. Hydrogen additions are shown to have a dominant role in determining deposition rate and polymer composition. A qualitative description of the polymer growth mechanism is presented which accounts for both changes in growth rate and structure, and leads to an empirical deposition rate model.

Technical innovation in industrial production

New techniques in manufacturing, popularly referred to as mechanization and automation, have been a preoccupation of social and economic theorists since the industrial revolution. A selection of relevant literature is reviewed, including the neoclassical economic treatment of technical change. This incorporates alterations to the mathematical production function and an associated increase in the efficiency with which the factors of production are converted into output. Other work emphasises the role of research and development and the process of diffusion, whereby new production techniques are propagated throughout industry. Some sociological writings attach importance to the type of production technology and its effect on the organisational structure and social relations within the factory. Nine detailed case studies are undertaken of examples of industrial innovation in the rubber, automobile, vehicle components, confectionery and clothing industries. The old and new techniques are compared for a range of variables, including capital equipment, labour employed, raw materials used, space requirements and energy consumption, which in most cases exhibit significant change with the innovation. The rate of output, labour productivity, product quality, maintenance requirements and other aspects are also examined. The process by which the change in production method was achieved is documented, including the development of new equipment and the strategy of its introduction into the factory, where appropriate. The firm, its environment, and the attitude of different sectors of the workforce are all seen to play a part in determining the motives for and consequences which flow from the innovations. The traditional association of technical progress with its labour-saving aspect, though an accurate enough description of the cases investigated, is clearly seen to afford an inadequate perspective for the proper understanding of this complex phenomenon, which also induces change in a wide range of other social, economic and technical variables.

Low severity Fischer-Tropsch synthesis for the production of synthetic hydrocarbon fuels

Currently, the main source for the production of liquid transportation fuels is petroleum, the continued use of which faces many challenges including depleting oil reserves, significant oil price rises, and environmental concerns over global warming which is widely believed to be due to fossil fuel derived CO2 emissions and other greenhouse gases. In this respect, lignocellulosic or plant biomass is a particularly interesting resource as it is the only renewable source of organic carbon that can be converted into liquid transportation fuels. The gasification of biomass produces syngas which can then be converted into synthetic liquid hydrocarbon fuels by means of the Fischer-Tropsch (FT) synthesis. This process has been widely considered as an attractive option for producing clean liquid hydrocarbon fuels from biomass that have been identified as promising alternatives to conventional fossil fuels like diesel and kerosene. The resulting product composition in FT synthesis is influenced by the type of catalyst and the reaction conditions that are used in the process. One of the issues facing this conversion process is the development of a technology that can be scaled down to match the scattered nature of biomass resources, including lower operating pressures, without compromising liquid composition. The primary aims of this work were to experimentally explore FT synthesis at low pressures for the purpose of process down-scaling and cost reduction, and to investigate the potential for obtaining an intermediate FT synthetic crude liquid product that can be integrated into existing refineries under the range of process conditions employed. Two different fixed-bed micro-reactors were used for FT synthesis; a 2cm3 reactor at the University of Rio de Janeiro (UFRJ) and a 20cm3 reactor at Aston University. The experimental work firstly involved the selection of a suitable catalyst from three that were available. Secondly, a parameter study was carried out on the 20cm3 reactor using the selected catalyst to investigate the influence of reactor temperature, reactor pressure, space velocity, the H2/CO molar ratio in the feed syngas and catalyst loading on the reaction performance measured as CO conversion, catalyst stability, product distribution, product yields and liquid hydrocarbon product composition. From this parameter study a set of preferred operating conditions was identified for low pressure FT synthesis. The three catalysts were characterized using BET, XRD, TPR and SEM. The catalyst selected was an unpromoted Co/Al2O3 catalyst. FT synthesis runs on the 20cm3 reactor at Aston were conducted for 48 hours. Permanent gases and light hydrocarbons (C1-C5) were analysed in an online GC-TCD/FID at hourly intervals. The liquid hydrocarbons collected were analyzed offline using GC-MS for determination of fuel composition. The parameter study showed that CO conversion and liquid hydrocarbon yields increase with increasing reactor pressure up to around 8 bar, above which the effect of pressure is small. The parameters that had the most significant influence on CO conversion, product selectivity and liquid hydrocarbon yields were reactor temperature and catalyst loading. The preferred reaction conditions identified for this research were: T = 230ºC, P = 10 bar, H2/CO = 2.0, WHSV = 2.2 h-1, and catalyst loading = 2.0g. Operation in the low range of pressures studied resulted in low CO conversions and liquid hydrocarbon yields, indicating that low pressure BTL-FT operation may not be industrially viable as the trade off in lower CO conversions and once-through liquid hydrocarbon product yields has to be carefully weighed against the potential cost savings resulting from process operation at lower pressures.

Making Sense of Home and Homeland: Former-Soviet Greeks' Motivations and Strategies for a Transnational Migrant Circuit

Focusing on former-Soviet Greeks' experiences of cross-border movement to Greece, this paper sheds light on the impact of this migration on the social identities of Russian Greeks as a transnational community. It draws on informants’ narratives and ethnographic observations recorded among Greek migrants in their home communities in southern Russia, and shows how their motivation, in their transnational movement, is determined by the ‘push-and-pull’ forces of socio-economic and political transformations in post-Soviet space. In these conditions, Greek identity becomes a resource which facilitates the organisation of transnational migration. The cultural, social and economic differences between the former-Soviet Greek migrants and the native-born population of Greece result in the emergence of a Pontic-Greek cultural identity which emphasises migrants’ connections with the former USSR. The difficulties of economic and cultural adaptation for migrants to Greece are examined in relation to the Russian Greeks' economic strategies within their home communities and their perception of the ‘homeland’ as a constantly contested and relocated social construct.

Diversity and knowledge in the age of nation-building: Space and time in the thought of Yanagita Kunio

The study examines the thought of Yanagita Kunio (1875–1962), an influential Japanese nationalist thinker and a founder of an academic discipline named minzokugaku. The purpose of the study is to bring into light an unredeemed potential of his intellectual and political project as a critique of the way in which modern politics and knowledge systematically suppresses global diversity. The study reads his texts against the backdrop of the modern understanding of space and time and its political and moral implications and traces the historical evolution of his thought that culminates in the establishment of minzokugaku. My reading of Yanagita’s texts draws on three interpretive hypotheses. First, his thought can be interpreted as a critical engagement with John Stuart Mill’s philosophy of history, as he turns Mill’s defense of diversity against Mill’s justification of enlightened despotism in non-Western societies. Second, to counter Mill’s individualistic notion of progressive agency, he turns to a Marxian notion of anthropological space, in which a laboring class makes history by continuously transforming nature, and rehabilitates the common people (jomin) as progressive agents. Third, in addition to the common people, Yanagita integrates wandering people as a countervailing force to the innate parochialism and conservatism of agrarian civilization. To excavate the unrecorded history of ordinary farmers and wandering people and promote the formation of national consciousness, his minzokugaku adopts travel as an alternative method for knowledge production and political education. In light of this interpretation, the aim of Yanagita’s intellectual and political project can be understood as defense and critique of the Enlightenment tradition. Intellectually, he attempts to navigate between spurious universalism and reactionary particularism by revaluing diversity as a necessary condition for universal knowledge and human progress. Politically, his minzokugaku aims at nation-building/globalization from below by tracing back the history of a migratory process cutting across the existing boundaries. His project is opposed to nation-building from above that aims to integrate the world population into international society at the expense of global diversity.

Conversações políticas no youtube: junho de 2013 e circulação de sentidos nos comentários do vídeo “globo e os protestos”

This re search analyzes the talks dynamics about policy established in YouTube symbolic space. We are interested in examining the way in which the commentators of the video " Globo e os Protestos " articulated in the field intended for comments, a public space directed to the dissemination and circulation of meanings about policy issues. The video studied was published by PC Siqueira and Diego Quint eiro , during the June 2013 protests in Br azil, to direct the political understanding of the movement lived in that period. According to them, the protests had left political position and therefore the protesters should reject the coverage by TV Globo (a comunication vehicle with ideals of right) and allow the participation of political parties linked to the ideological left spectrum. This narrative generated empathy and controversy betwe en commentators, which produced in the comments, an intense argumentative process about these theses (right and left). To understand the phenomenon, we conducted an exploratory qualitative research, the main methodological procedure was a ethnomethodological discourse analysis. We seek the observation of the ways in which the commentators es tablished talks about politics in the comments space, for, thereafter , organize categories of analysis based on identified discursive recurrences. The empirical reflections are supported from discussions about the YouTube potential, while digital media com prising massive strategies and while articulating space in the engagement of individuals in political issues; also confront the aspects involved in the conversation practices that results in sociability dynamics and , especially , in conflict, on the socio - t echnical networks; and finally, we propose a reflection about the circuit actuation in which the people take ownership and realize new readings about the products received. Concluding that the use of digital media , such as YouTube, has caused significant c hanges in the forms of production and reception of symbolic products and ways in which people participate in political issues concerning life in society.

Le cycle hydrosocial et la fluoration de l'eau : la production des eaux fluorées

La fluoration artificielle de l’eau est une méthode employée en tant que moyen de prévention de la carie dentaire. Il s’agit d’un traitement de l’eau dont le but est d’ajuster de façon « optimale » la concentration en fluorure dans l’eau potable pour la prévention de la carie dentaire, par l’ajout d’un composé fluoré. La fluoration de l’eau fait l’objet d’un débat de société depuis le début des années 1950. La théorie du cycle hydrosocial nous invite à réfléchir sur la manière dont l’eau et la société se définissent et se redéfinissent mutuellement dans le temps et dans l’espace. Cette théorie nous permet d’aborder l’étude du sujet de la fluoration avec une nouvelle perspective d’analyse. Il y a peu d’études en sciences sociales qui portent sur le sujet de la fluoration, généralement abordé d’un point de vue des sciences de la santé. Nous proposons de décrire le processus de production des eaux fluorées dans un contexte hydrosocial. Ce mémoire est structuré en quatre chapitres. Nous commençons par familiariser le lecteur avec la théorie du cycle hydrosocial. Ensuite, nous faisons une mise en contexte de la fluoration de l’eau, d’une part en présentant un état des lieux, et d’autre part en présentant ce en quoi consiste la pratique de la fluoration de l’eau. Après avoir familiarisé le lecteur avec les thèmes généraux concernant la fluoration de l’eau, nous proposons de reconstituer une histoire hydrosociale de la fluoration. Cette histoire nous permet de mettre en évidence les relations hydrosociales desquelles découle la production des eaux fluorées. L’histoire hydrosociale de la fluoration comporte une phase contemporaine que nous abordons en présentant les principales idées de l’opposition à la fluoration artificielle de l’eau à l’aide notamment d’une analyse iconographique d’images portant sur le thème de la fluoration. Finalement, nous discutons des implications de la théorie du cycle hydrosocial pour étudier la problématique de la fluoration.