On the spatial and temporal dependence of CO2 emission on soil properties in sugarcane (Saccharum spp.) production

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Preparo do solo e emissão de CO2, temperatura e umidade do solo em área canavieira

Soil tillage is one of the agricultural practices that may contribute to increase the loss of carbon through emission of CO2 (FCO2). The aim of this study was to investigate the effect of three soil tillage systems on FCO2, soil temperature and soil moisture in a sugarcane area under reform. The experimental area consisted of three tillage plots: conventional tillage (CT), conventional subsoiling (CS), and localized subsoiling (LS). FCO2, soil temperature and soil moisture were measured over a period of 17 days. FCO2 showed the highest value in CT (0.75 g CO2 m(-2) h(-1)). Soil temperature presented no significant difference (p > 0.05) between LS (26.2 degrees C) and CS (25.9 degrees C). Soil moisture was higher in LS (24%), followed by CS (21.8%) and CT (18.3%). A significant correlation (r = -0.71; p < 0.05) between FCO2 and soil temperature was observed only in CT. The conventional tillage presented a total emission (2,864.3 kg CO2 ha(-1)) higher than the emissions observed in CS (1,970.9 kg CO2 ha(-1)) and LS (1,707.7 kg CO2 ha(-1)). The conversion from CT to LS decreased soil CO2 emissions, reducing the contribution of agriculture in increasing the concentration of greenhouse gases in the atmosphere.

Analysis of oxy-fuel combustion as an alternative to combustion with air in metal reheating furnaces

Using oxygen instead of air in a burning process is at present being widely discussed as an option to reduce CO2 emissions. One of the possibilities is to maintain the combustion reaction at the same energy release level as burning with air, which reduces fuel consumption and the emission rates of CO2. A thermal simulation was made for metal reheating furnaces, which operate at a temperature in the range of 1150-1250 degrees C, using natural gas with a 5% excess of oxygen, maintaining fixed values for pressure and combustion temperature. The theoretical results show that it is possible to reduce the consumption of fuel, and this reduction depends on the amount of heat that can be recovered during the air pre-heating process. The analysis was further conducted by considering the 2012 costs of natural gas and oxygen in Brazil. The use of oxygen showed to be economically viable for large furnaces that operate with conventional heat recovering systems (those that provide pre-heated air at temperatures near 400 degrees C). (C) 2014 Elsevier Ltd. All rights reserved.

Greenhouse gas emissions and N2o mitigation in beef cattle production on tropical pasture

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Soil greenhouse gas emissions and their relations to soil attributes in a sugarcane area

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Variabilidade espaço-temporal da emissão de CO2 do solo em curto período sob influência de eventos de precipitação

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise termoeconômica e eficiência ecológica de uma termoelétrica com absorção química de CO2

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Desenvolvimento de uma câmara para combustão de combustíveis líquidos, operando sob regime de combustão sem chama visível

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Emissão de CO2 do solo em áreas de restauração na Mata Atlântica

Pós-graduação em Geociências e Meio Ambiente - IGCE

Cultivo de Eucalyptus urograndis em atmosfera enriquecida com CO2: mudanças no proteoma cloroplastidial

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

The sustainability of ethanol production from sugarcane

The rapid expansion of ethanol production from sugarcane in Brazil has raised a number of questions regarding its negative consequences and sustainability. Positive impacts are the elimination of lead compounds from gasoline and the reduction of noxious emissions. There is also the reduction of CO2 emissions, since sugarcane ethanol requires only a small amount of fossil fuels for its production, being thus a renewable fuel. These positive impacts are particularly noticeable in the air quality improvement of metropolitan areas but also in rural areas where mechanized harvesting of green cane is being introduced, eliminating the burning of sugarcane. Negative impacts such as future large-scale ethanol production from sugarcane might lead to the destruction or damage of high-biodiversity areas, deforestation, degradation or damaging of soils through the use of chemicals and soil decarbonization, water resources contamination or depletion, competition between food and fuel production decreasing food security and a worsening of labor conditions on the fields. These questions are discussed here, with the purpose of clarifying the sustainability aspects of ethanol production from sugarcane mainly in Sao Paulo State, where more than 60% of Brazil`s sugarcane plantations are located and are responsible for 62% of ethanol production. (c) 2008 Elsevier Ltd. All rights reserved.

Methodology of CO2 emission evaluation in the life cycle of office building facades

The construction industry is one of the greatest sources of pollution because of the high level of energy consumption during its life cycle. In addition to using energy while constructing a building, several systems also use power while the building is operating, especially the air-conditioning system. Energy consumption for this system is related, among other issues, to external air temperature and the required internal temperature of the building. The facades are elements which present the highest level of ambient heat transfer from the outside to the inside of tall buildings. Thus, the type of facade has an influence on energy consumption during the building life cycle and, consequently, contributes to buildings' CO2 emissions, because these emissions are directly connected to energy consumption. Therefore, the aim is to help develop a methodology for evaluating CO2 emissions generated during the life cycle of office building facades. The results, based on the parameters used in this study, show that facades using structural glazing and uncolored glass emit the most CO2 throughout their life cycle, followed by brick facades covered with compound aluminum panels or ACM (Aluminum Composite Material), facades using structural glazing and reflective glass and brick facades with plaster coating. On the other hand, the typology of facade that emits less CO2 is brickwork and mortar because its thermal barrier is better than structural glazing facade and materials used to produce this facade are better than brickwork and ACM. Finally, an uncertainty analysis was conducted to verify the accuracy of the results attained. (C) 2011 Elsevier Inc. All rights reserved.

Combustion of coal, bagasse and blends thereof Part I: Emissions from batch combustion of fixed beds of fuels

Batch combustion of fixed beds of coal, bagasse and blends thereof took place in a pre-heated two-stage electric laboratory furnace, under high-heating rates. The average input fuel/air equivalence ratios were similar for all fuels. The primary and secondary furnace temperatures were varied from 800 degrees C to 1000 degrees C. The effects of fuel blending, combustion staging, and operating furnace temperatures on the emissions from the two fuels were assessed. Furnace effluents were analyzed for carbon dioxide and for products of incomplete combustion (PIC) including CO, volatile and semi-volatile hydrocarbons, as well as particulate matter. Results showed that whereas CO2 was generated during both the observed sequential volatile matter and char combustion phases of the fuels, PICs were only generated during the volatile matter combustion phase. CO2 emissions were the highest from coal, whereas CO and other PIC emissions were the highest from bagasse. Under this particular combustion configuration, combustion of the volatile matter of the blends resulted in lower yields of PIC, than combustion of the volatiles of the neat fuels. Though CO and unburned hydrocarbons from coal as well as from the blends did not exhibit a clear trend with furnace temperature, such emissions from bagasse clearly increased with temperature. The presence of the secondary furnace (afterburner) typically reduced PIC, by promoting further oxidation of the primary furnace effluents. (C) 2012 Elsevier Ltd. All rights reserved.

Sulla ricerca del minimo dei consumi per vetture sportive

La ricerca oggetto di questa tesi, come si evince dal titolo stesso, è volta alla riduzione dei consumi per vetture a forte carattere sportivo ed elevate prestazioni specifiche. In particolare, tutte le attività descritte fanno riferimento ad un ben definito modello di vettura, ovvero la Maserati Quattroporte. Lo scenario all’interno del quale questo lavoro si inquadra, è quello di una forte spinta alla riduzione dei cosiddetti gas serra, ossia dell’anidride carbonica, in linea con quelle che sono le disposizioni dettate dal protocollo di Kyoto. La necessità di ridurre l’immissione in atmosfera di CO2 sta condizionando tutti i settori della società: dal riscaldamento degli edifici privati a quello degli stabilimenti industriali, dalla generazione di energia ai processi produttivi in senso lato. Nell’ambito di questo panorama, chiaramente, sono chiamati ad uno sforzo considerevole i costruttori di automobili, alle quali è imputata una percentuale considerevole dell’anidride carbonica prodotta ogni giorno e riversata nell’atmosfera. Al delicato problema inquinamento ne va aggiunto uno forse ancor più contingente e diretto, legato a ragioni di carattere economico. I combustibili fossili, come tutti sanno, sono una fonte di energia non rinnovabile, la cui disponibilità è legata a giacimenti situati in opportune zone del pianeta e non inesauribili. Per di più, la situazione socio politica che il medio oriente sta affrontando, unita alla crescente domanda da parte di quei paesi in cui il processo di industrializzazione è partito da poco a ritmi vertiginosi, hanno letteralmente fatto lievitare il prezzo del petrolio. A causa di ciò, avere una vettura efficiente in senso lato e, quindi, a ridotti consumi, è a tutti gli effetti un contenuto di prodotto apprezzato dal punto di vista del marketing, anche per i segmenti vettura più alti. Nell’ambito di questa ricerca il problema dei consumi è stato affrontato come una conseguenza del comportamento globale della vettura in termini di efficienza, valutando il miglior compromesso fra le diverse aree funzionali costituenti il veicolo. Una parte consistente del lavoro è stata dedicata alla messa a punto di un modello di calcolo, attraverso il quale eseguire una serie di analisi di sensibilità sull’influenza dei diversi parametri vettura sul consumo complessivo di carburante. Sulla base di tali indicazioni, è stata proposta una modifica dei rapporti del cambio elettro-attuato con lo scopo di ottimizzare il compromesso tra consumi e prestazioni, senza inficiare considerevolmente queste ultime. La soluzione proposta è stata effettivamente realizzata e provata su vettura, dando la possibilità di verificare i risultati ed operare un’approfondita attività di correlazione del modello di calcolo per i consumi. Il beneficio ottenuto in termini di autonomia è stato decisamente significativo con riferimento sia ai cicli di omologazione europei, che a quelli statunitensi. Sono state inoltre analizzate le ripercussioni dal punto di vista delle prestazioni ed anche in questo caso i numerosi dati rilevati hanno permesso di migliorare il livello di correlazione del modello di simulazione per le prestazioni. La vettura con la nuova rapportatura proposta è stata poi confrontata con un prototipo di Maserati Quattroporte avente cambio automatico e convertitore di coppia. Questa ulteriore attività ha permesso di valutare il differente comportamento tra le due soluzioni, sia in termini di consumo istantaneo, che di consumo complessivo rilevato durante le principali missioni su banco a rulli previste dalle normative. L’ultima sezione del lavoro è stata dedicata alla valutazione dell’efficienza energetica del sistema vettura, intesa come resistenza all’avanzamento incontrata durante il moto ad una determinata velocità. Sono state indagate sperimentalmente le curve di “coast down” della Quattroporte e di alcune concorrenti e sono stati proposti degli interventi volti alla riduzione del coefficiente di penetrazione aerodinamica, pur con il vincolo di non alterare lo stile vettura.

Carbon dioxide sequestration in cement kiln dust through miner carbonation

The feasibility of carbon sequestration in cement kiln dust (CKD) was investigated in a series of batch and column experiments conducted under ambient temperature and pressure conditions. The significance of this work is the demonstration that alkaline wastes, such as CKD, are highly reactive with carbon dioxide (CO2). In the presence of water, CKD can sequester greater than 80% of its theoretical capacity for carbon without any amendments or modifications to the waste. Other mineral carbonation technologies for carbon sequestration rely on the use of mined mineral feedstocks as the source of oxides. The mining, pre-processing and reaction conditions needed to create favorable carbonation kinetics all require significant additions of energy to the system. Therefore, their actual net reduction in CO2 is uncertain. Many suitable alkaline wastes are produced at sites that also generate significant quantities of CO2. While independently, the reduction in CO2 emissions from mineral carbonation in CKD is small (~13% of process related emissions), when this technology is applied to similar wastes of other industries, the collective net reduction in emissions may be significant. The technical investigations presented in this dissertation progress from proof of feasibility through examination of the extent of sequestration in core samples taken from an aged CKD waste pile, to more fundamental batch and microscopy studies which analyze the rates and mechanisms controlling mineral carbonation reactions in a variety of fresh CKD types. Finally, the scale of the system was increased to assess the sequestration efficiency under more pilot or field-scale conditions and to clarify the importance of particle-scale processes under more dynamic (flowing gas) conditions. A comprehensive set of material characterization methods, including thermal analysis, Xray diffraction, and X-ray fluorescence, were used to confirm extents of carbonation and to better elucidate those compositional factors controlling the reactions. The results of these studies show that the rate of carbonation in CKD is controlled by the extent of carbonation. With increased degrees of conversion, particle-scale processes such as intraparticle diffusion and CaCO3 micropore precipitation patterns begin to limit the rate and possibly the extent of the reactions. Rates may also be influenced by the nature of the oxides participating in the reaction, slowing when the free or unbound oxides are consumed and reaction conditions shift towards the consumption of less reactive Ca species. While microscale processes and composition affects appear to be important at later times, the overall degrees of carbonation observed in the wastes were significant (> 80%), a majority of which occurs within the first 2 days of reaction. Under the operational conditions applied in this study, the degree of carbonation in CKD achieved in column-scale systems was comparable to those observed under ideal batch conditions. In addition, the similarity in sequestration performance among several different CKD waste types indicates that, aside from available oxide content, no compositional factors significantly hinder the ability of the waste to sequester CO2.