Thermal, mechanical and ionic conductive behaviour of gamma-radiation induced PEO/PVDF(SIN)-LiClO4 polymer electrolyte system

An effort has been made to modify the mechanical behaviour of our previously reported gel-type gamma-radiation crosslinked polyethylene oxide (PEO)-LiClO4 polymer electrolyte. A highly polar and gamma-radiation crosslinkable crystalline polymer, polyvinylidene fluoride (PVDF), was selected to blend with PEO and then subjected to gamma-irradiation in order to make an simultaneous interpenetrating network (SIN), which was used as a polymer host to impart stiffness to the plasticized system. Experimental results have shown that the presence of PVDF in the system, through gamma-radiation induced SIN formation, could not only give a rather high mechanical modulus of 10(7) Pa at ambient temperature, but also maintain the room temperature ionic conductivity at a high level (greater than 10(-4) S/cm). DSC, DMA and conductivity measurement techniques were used to examine the effects of blending, gamma-irradiation and plasticization on the variations of glass transition and melting endotherm, on the appearance of high elastic plateau and on the temperature dependence of ionic conductivity: In addition, it was found that, in contrast with the unplasticized system, the ionic conductivity mechanism of this gel-type electrolyte seems to conform to the Arrhenius model, suggesting that, as a result of the high degree of plasticization, the polymer chains act mainly as the skeleton of the networks or polymer cages to immobilize the liquid electrolyte solution, whereas the ionic species migrate as if they were in a liquid medium. (C) 1997 Elsevier Science Ltd.

Morphology, thermal behavior, and mechanical properties of PA1010/PP and PA1010/PP-g-GMA blends

The modification of polypropylene (PP) was accomplished by melt grafting glycidyl methacrylate (GMA) on its molecular chains. The resulting PP-g-GMA was used to prepare binary blends of polyamide 1010 (PA1010) and PP-g-GMA. Different blend morphologies were observed by scanning electron microscopy (SEM) according to the nature and content of PA1010 used. Comparing the PA1010/PP-g-GMA and PA1010/PP binary blends, the size of the domains of PP-g-GMA were much smaller than that of PP at the same compositions. It was found that mechanical properties of PA1010/PP-g-GMA blends were obviously better than that of PA1010/PP blends, and the mechanical properties were significantly influenced by wetting conditions for uncompatibilized and compatibilized blends. A different dependence of the flexural modulus on water was found for PA1010/PP and PA1010/PP-g-GMA. These behaviors could be attributed to the chemical interactions between the two components and good dispersion in PA1010/PP-g-GMA blends. Thermal and rheological analyses were performed to confirm the possible chemical reactions taking place during the blending process. (C) 1997 John Wiley & Sons, Inc.

Study of the miscibility and thermodynamics of cellulose diacetate-poly(vinyl pyrrolidone) blends

The miscibility of blends of cellulose diacetate (CDA) and poly(vinyl pyrrolidone) (PVP) was extensively studied by means of differential thermal analysis and dynamic mechanical thermal analysis, tensile test, measuring viscosity of diluted and concentrated solutions of blends in acetone-ethanol mixture and morphological observations. A single glass transition temperature is observed, which is intermediate between the glass transition temperatures associated with each component and depends on composition. A synergism in mechanical properties of blends was found. The absolute viscosity and the intrinsic viscosity of solutions of blends are much higher than the weight average values of solutions of CDA and PVP. Optically clear and thermodynamically stable films were formed in the composition range of CDA/PVP = 100/0 to 50/50w/w. Fourier transform infrared was used to investigate the nature of CDA-PVP interaction. Hydrogen bonds were formed between hydroxyl groups of CDA and carbonyl groups of PVP. Heats of solutions of CDA/PVP blends and their mechanical mixtures were measured by using a calorimeter. Mixing enthalpy obtained with Hess's law approach was used to quantify interaction parameters of this blending system. It was found that mixing enthalpies and interaction parameters were negative and composition dependent. (C) 1997 Elsevier Science Ltd.

Properties of ethylene-propylene copolymer/PA-1010 blends using ethylene-propylene copolymer-graft-acrylic acid as a compatibilizing agent

The modification of ethylene-propylene copolymer (EP) has been accomplished by radical EP-graft-acrylic acid (EP-g-AA) has been used to obtain ternary PA/EP/EP-g-AA blends by melt mixing. Different blend morphologies were observed by scanning electron microscopy; the domain size of the EP-dispersed phase in the polyamide 1010 matrix of compatibilized blends decreased compared with that of uncompatibilized blends. It is found that EP-g-AA used as the third component has a profound effect on the mechanical properties of the resulting blends. This behavior has been attributed to serious chemical interactions taking place between the two components. Thermal analysis shows that some thermal properties of PA in compatibilized PA/EP/EP-g-AA changed because of chemical reactions taken place during the blending process. Wide angle x-ray diffraction measurements also confirmed this result. (C) 1996 John Wiley & Sons, Inc.

Electrical and dynamic mechanical behavior of carbon black filled polymer composites

The effect of processing conditions on the electrical and dynamic behavior of carbon black (CB) filled ethylene/ethylacrylate copolymer (EEA) composites was investigated. The compounds were prepared by two methods, solution blending and mechanical mixing. Compared with the solution counterpart, the mechanical composites have a strong positive temperature coefficient (PTC) effect and a high dynamic elastic modulus, which results from the good dispersion state of carbon black in EEA, i.e. the strong interaction between carbon black and EEA. It can be concluded that the strong interaction between polymer and carbon black is essential for composites to have a high PTC intensity, good electrical reproducibility and high dynamic elastic modulus. Copyright (C) 1996 Published by Elsevier Science Ltd.

Miscibility and crystallization behaviour of poly(ether ether ketone)/polyimide blends

The miscibility and crystallization behaviour of the blends of poly(ether ether ketone) (PEEK) with two thermoplastic polyimides (PI), PEI-E and YS-30, prepared by solution blending were studied by the use of small-angle X-ray scattering (SAXS), differential scanning calorimetry (d.s.c.) and polarizing microscopy techniques. The results obtained show that PEEK/YS-30 is miscible, while PEEK/PEI-E is partially miscible only in the composition range with PEI-E content up to 20 wt%. The crystallization behaviour of PEEK in PEEK/PI blends depends on the crystallization condition of the blend sample as well as the chemical structure and the content of the PI added. Our SAXS results indicate that the segregation of PI molecular chains during crystallization of PEEK chains in the blends is interfibrillar for PEEK/PEI-E blends, but interlamellar for PEEK/YS-30 blends. The compatibility and the crystallization behaviour are discussed in terms of charge transfer interaction between PI and PI molecules and between PI and PEEK molecules.

FRACTURE-TOUGHNESS AND MORPHOLOGY OF PHENOLPHTHALEIN POLY(ETHER SULFONE) THERMOTROPIC LIQUID-CRYSTALLINE POLYMER BLENDS

Blends of a new phenolphthalein poly (ether sulfone) (PES-C) and a thermotropic liquid crystalline polymer (LCP) were prepared by melt-blending in a twin-screw extruder. Rheological properties, fracture toughness, K(IC), and morphology of the blends were

A STUDY ON POLYMER-POLYMER INTERACTIONS THROUGH MIXING CALORIMETRY

The aim of this work is to describe the most recent achievements in the field of the physical chemistry of mixing. The systems studied have been classified according to the amount of thermic effect due to the blending and its interpretation. When polystyrene (PS) and poly(alpha-methylstyrene) (P alpha MS) are blended, the interaction is weak and Delta(mix)H is close to zero. The presence of polar atoms and/or groups increases the stability of the blend and, therefore, Delta(mix)H becomes more negative. Poly(ethylene oxide) (PEO), poly(methyl acrylate) (PMA), poly(methyl methacrylate) (PMMA) and poly(vinylacetate) (PVAc), when mixed to form binary systems, show large differences from their properties when pure. If hydrogen bonding takes place, the interactions are readily detected and a large effect is calorimetrically determined. Cellulose diacetate (CDA) and poly(vinylpyrrolidone) (PVP) have been studied as an example of a strongly interacting system.

STUDIES ON RADIATION-INDUCED CROSS-LINKING OF POLYISOBUTYLENE

Polyisobutylene can be crosslinked under irradiation as to be expected by either introducing radiation sensitive groups into its macromolecules or blending with a proper radiation crosslinkable polymer.

A HIGH-RESOLUTION SOLID-STATE NMR AND DSC STUDY OF MISCIBILITY AND CRYSTALLIZATION BEHAVIOR OF POLY(VINYL ALCOHOL)/POLY(N-VINYL-2-PYRROLIDONE) BLENDS

Blends of crystallizable poly(vinyl alcohol) (PVA) with poly(N-vinyl-2-pyrrolidone) (PVPy) were studied by C-13 cross-polarization/magic angle spinning (CP/MAS) n.m.r. and d.s.c. The C-13 CP/MAS spectra show that the blends were miscible on a molecular level over the whole composition range studied, and that the intramolecular hydrogen bonds of PVA were broken and intermolecular hydrogen bonds between PVA and PVPy formed when the two polymers were mixed. The results of a spin-lattice relaxation study indicate that blending of the two polymers reduced the average intermolecular distance and molecular motion of each component, even in the miscible amorphous phase, and that addition of PVPy into PVA has a definite effect on the crystallinity of PVA in the blends over the whole composition range, yet there is still detectable crystallinity even when the PVPy content is as high as 80 wt%. These results are consistent with those obtained from d.s.c. studies.

基于神经网络的水泥生料配料多目标优化设计方法

为了降低生料成分的不确定性给水泥生料质量控制系统带来的影响,提出了率值补偿的控制策略.分别为三率值创建目标函数,并利用状态空间搜索策略解决多目标优化问题.针对初始样本空间不能覆盖所有样本的问题,提出了基于神经网络的估算模型,对初始样本空间进行拓扑.通过估价函数对状态空间中的状态量进行评价,得到最优的率值状态量;根据率值对原料配比进行调整,最后使率值偏差得到补偿,同时使给配比造成的波动最小.工业实验结果表明,生料的质量合格率由原来的30%提高到50%,该系统能有效地对配料过程进行优化控制.证明了基于神经网络的状态空间搜索策略为水泥生料配料多目标寻优问题提供了一种可行的方法。

Towards an Example-Based Image Compression Architecture for Video-Conferencing

This paper consists of two major parts. First, we present the outline of a simple approach to very-low bandwidth video-conferencing system relying on an example-based hierarchical image compression scheme. In particular, we discuss the use of example images as a model, the number of required examples, faces as a class of semi-rigid objects, a hierarchical model based on decomposition into different time-scales, and the decomposition of face images into patches of interest. In the second part, we present several algorithms for image processing and animation as well as experimental evaluations. Among the original contributions of this paper is an automatic algorithm for pose estimation and normalization. We also review and compare different algorithms for finding the nearest neighbors in a database for a new input as well as a generalized algorithm for blending patches of interest in order to synthesize new images. Finally, we outline the possible integration of several algorithms to illustrate a simple model-based video-conference system.

A framework for the transformation of the creative industries in a digital age.

The creative industries sector faces a constantly changing context characterised by the speed of the development and deployment of digital information systems and Information Communications Technologies (ICT) on a global scale. This continuous digital disruption has had significant impact on the whole value chain of the sector: creation and production; discovery and distribution; and consumption of cultural goods and services. As a result, creative enterprises must evolve business and operational models and practices to be sustainable. Enterprises of all scales, type, and operational model are affected, and all sectors face ongoing digital disruption. Management consultancy practitioners and business strategy academics have called for new strategy development frameworks and toolkits, fit for a continuously changing world. This thesis investigates a novel approach to organisational change appropriate to the digital age, in the context of the creative sector in Scotland. A set of concepts, methods, tools, and processes to generate theoretical learning and practical knowing was created to support enterprises to digitally adapt through undertaking journeys of change and organisational development. The framework is called The AmbITion Approach. It was developed by blending participatory action research (PAR) methods and modern management consultancy, design, and creative practices. Empirical work also introduced to the framework Coghlan and Rashford’s change categories. These enabled the definition and description of the extent to which organisations developed: whether they experienced first order (change), second order (adaptation) or third order (transformation) change. Digital research tools for inquiry were tested by a pilot study, and then embedded in a longitudinal study over two years of twentyone participant organisations from Scotland’s creative sector. The author applied and investigated the novel approach in a national digital development programme for Scotland’s creative industries. The programme was designed and delivered by the author and ran nationally between 2012-14. Detailed grounded thematic analysis of the data corpus was undertaken, along with analysis of rich media case studies produced by the organisations about their change journeys. The results of studies on participants, and validation criteria applied to the results, demonstrated that the framework triggers second (adaptation) and third order change (transformation) in creative industry enterprises. The AmbITion Approach framework is suitable for the continuing landscape of digital disruption within the creative sector. The thesis contributes to practice the concepts, methods, tools, and processes of The AmbITion Approach, which have been empirically tested in the field, and validated as a new framework for business transformation in a digital age. The thesis contributes to knowledge a theoretical and conceptual framework with a specific set of constructs and criteria that define first, second, and third order change in creative enterprises, and a robust research and action framework for the analysis of the quality, validity and change achieved by action research based development programmes. The thesis additionally contributes to the practice of research, adding to our understanding of the value of PAR and design thinking approaches and creative practices as methods for change.

Physically-Based Combinations of Views: Representing Rigid and Nonrigid Motion

Nonrigid motion can be described as morphing or blending between extremal shapes, e.g., heart motion can be described as transitioning between the systole and diastole states. Using physically-based modeling techniques, shape similarity can be measured in terms of forces and strain. This provides a physically-based coordinate system in which motion is characterized in terms of physical similarity to a set of extremal shapes. Having such a low-dimensional characterization of nonrigid motion allows for the recognition and the comparison of different types of nonrigid motion.

OPERA IN AMERICA: MUSIC OF, BY, AND FOR THE PEOPLE­: A PERFORMANCE DISSERTATION

Opera in America: Music of, by, and for the people is a study of the relationship between American popular culture and opera in the United States. Four performance projects demonstrate the on-going exchange between the operatic community-including its composer, singers, and patrons-and the country's popular entertainment industry with its broad audience base. Numerous examples of artistic cross pollination between lowbrow and highbrow music will illustrate the artistic and social consequences created by this artistic amalgamation. Program #1, By George! By Ira! By Gershwin!, is a retrospective of Gershwin's vocal music representing a blending of popular and serious music in both style and form. The concert includes selections from Porgy and Bess, a work considered by many musicologists as the first American opera. Program #2, Shadowboxer, is a premiere performance of an opera by Frank Proto and John Chenault. For this newly commissioned work, I serve as Assistant Director to Leon Major. Shadowboxer provides a clear example of opera utilizing popular culture both musically and dramatically to tell the true story of American hero and legendary boxer, Joe Louis. Program #3, Just a Song at Twilight, is an original theatrical music piece featuring music, letters, diaries, and journals of the Gilded Age, an era when opera was synonymous with popular entertainment. Special attention is focused on tum-of­ the-century singers who performed in both opera and vaudeville. Program #4 is a presentation of Dominick Argento's Miss Manners on Music and illustrates the strong relationship that can exist between opera and American popular entertainment. Originally conceived as a song cycle, I have staged the work as a one-act opera sung and acted by soprano Carmen Balthrop. This piece is based on the writings of pop icon and newspaper columnist Judith Martin, otherwise known as Miss Manners. All four performances are recorded in audio and video formats.