The influence of Fe-rich coatings on the dissolution of anorthite at pH 2.6

Surface coatings are very common on mineral grains in soils but most laboratory dissolution experiments are carried out on pristine, uncoated mineral grains. An experiment designed to unambiguously isolate the effect of surface coatings on mineral dissolution from any influence of solution saturation state is reported. Two aliquots of 53 to 63 mum anorthite feldspar powder were used. One was dissolved in pH 2.6 HCl, the other in pH 2.6 FeCl3 solution, both for similar to6000 h in flow-through reactors. An amorphous Fe-rich, Al-, Ca- and Si-free orange precipitate coated the anorthite dissolved in the FeCl3 solution. BET surface area of the anorthite increased from 0.16 to 1.65 m(2) g(-1) in the HCl experiment and to 3.89 m(2) g(-1) in the FeCl3 experiment. The increase in surface area in the HCl experiment was due to the formation of etch pits on the anorthite grain surface whilst the additional increase in the FeCl3 experiment was due to the micro- and meso-porous nature of the orange precipitate. This precipitate did not inhibit or slow the dissolution of the anorthite. Steady state dissolution rates for the anorthite dissolved in the HCl and FeCl3 were similar to2.5 and 3.2 X 10(-10) mol(feldspar) m(-2) s(-1) respectively. These rates are not significantly different after the cumulative uncertainty of 17% in their value due to uncertainty in the inputs parameters used in their calculation is taken into account. Results from this experiment support previous theoretical and inference-based conclusions that porous coatings should not inhibit mineral dissolution. Copyright (C) 2003 Elsevier Ltd.

Extraction behavior of the synergistic system 2,6-bis-(benzoxazolyl)-4-dodecyloxylpyridine and 2-bromodecanoic acid using Am and Eu as radioactive tracers

In this study, the extraction properties of a synergistic system consisting of 2,6-bis-(benzoxazolyl)-4-dodecyloxylpyridine (BODO) and 2-bromodecanoic acid (HA) in tert-butyl benzene (TBB) have been investigated as a function of ionic strength by varying the nitrate ion and perchlorate ion concentrations. The influence of the hydrogen ion concentration has also been investigated. Distribution ratios between 0.03-12 and 0.003-0.8 have been found for Am(III) and Eu(HI), respectively, but there were no attempts to maximize these values. It has been shown that the distribution ratios decrease with increasing amounts of ClO4-, NO3-, and H+. The mechanisms, however, by which the decrease occurs, are different. In the case of increasing perchlorate ion concentration, the decrease in extraction is linear in a log-log plot of the distribution ratio vs. the ionic strength, while in the nitrate case the complexation between nitrate and Am or Eu increases at high nitrate ion concentrations and thereby decreases the distribution ratio in a non-linearway. The decrease in extraction could be caused by changes in activity coefficients that can be explained with specific ion interaction theory (SIT); shielding of the metal ions, and by nitrate complexation with Am and Eu as competing mechanism at high ionic strengths. The separation factor between Am and Eu reaches a maximum at similar to1 M nitrate ion concentration. Thereafter the values decrease with increasing nitrate ion concentrations.

Mono- and heterodimetallic FeII and RuII complexes based on a novel heteroditopic 4′-{bis(phosphanyl)aryl}-2,2′:6′,2″-terpyridine ligand

In the search for a versatile building block that allows the preparation of heteroditopic tpy-pincer bridging ligands, the synthon 14'-[C6H3(CH2Br)(2)-3,5]-2,2':6',2 ''-terpyridine was synthesized. Facile introduction of diphenylphosphanyl groups in this synthon gave the ligand 14'-[C6H3(CH2PPh2)2-3,5]-2,2':6',2"-terpyridine) ([tpyPC(H)Pj). The asymmetric mononuclear complex [Fe(tpy){tpyPC(H)P}](PF6)(2), prepared by selective coordination of [Fe(tpy)Cl-3] to the tpy moiety of [tpyPC(H)P], was used for the synthesis of the heterodimetallic complex [Fe(tpy)(tpyPCP)Ru(tpy)](PFC,)3, which applies the "complex as ligand" approach. Coordination of the ruthenium centre at the PC(H)P-pincer moiety of [Fe(tpy){tpyPC(H)P}](PF6)(2) has been achieved by applying a transcyclometallation procedure. The ground-state electronic properties of both complexes, investigated by cyclic and square-wave voltammetries and UV/Vis spectroscopy, are discussed and compared with those of [Fe(tPY)(2)](PF6)(2) and [Ru(PCP)(tpy)]Cl, which represent the mononuclear components of the heterodinuclear species. An in situ UV/Vis spectroelectrochemical study was performed in order to localize the oxidation and reduction steps and to gain information about the Fe-II-Ru-II communication in the heterodimetallic system [Fe(tpy)(tpyPCP)Ru(tpy)](PF6)(3) mediated by the bridging ligand [tpyPCP]. Both the voltammetric and spectroelectrochemical results point to only very limited electronic interaction between the metal centres in the ground state.

Molecular structures and electronic transitions of 3,6-Diphenyl-1,2-dithiin and its radical cation: a spectroelectrochemical and DFT study

One-electron oxidation of 3,6-diphenyl-1,2-dithiin yields the corresponding radical cation. The product is stable at low temperatures and can be distinguished by a triplet EPR signal. Cyclic voltammetric, UV-vis spectroelectrochemical, and DFT studies were performed to elucidate its molecular structure and electronic properties. Time-dependent DFT calculations reproduce appreciably well the UV-vis spectral changes observed during the oxidation. The results reveal a moderately twisted structure of the 1,2-dithiin heterocycle in the radical cation.

Synthesis, spectroscopy and spectroelectrochemistry of chlorocarbonyl {1,2-bis[(2,6-diisopropylphenyl)imino]-acenaphthene-kappa(2)-N,N '}rhodium (I)

Reaction of the dinuclear complex [{Rh(CO)(2)}(2) (mu-Cl)(2)]with an alpha-diimine ligand, 1,2- bis[(2,6-diisopropylphenyl) imino] acenaphthene (iPr(2)Ph-bian), produces square-planar [RhCl(CO)(iPr(2)Ph-bian)]. For the first time, 2: 1 and 1: 1 alpha-diimine/dimer reactions yielded the same product. The rigidity of iPr(2)Ph-bian together with its flexible electronic properties and steric requirements of the 2,6-diisopropyl substituents on the benzene rings allow rapid closure of a chelate bond and replacement of a CO ligand instead of chloride. A resonance Raman study of [RhCl(CO)(iPr(2)Ph-bian)] has revealed a predominant Rh-to-bian charge transfer (MLCT) character of electronic transitions in the visible spectral region. The stabilisation of [RhCl(CO)(iPr(2)Ph-bian)] in lower oxidation states by the pi-acceptor iPr(2)Ph-bian ligand was investigated in situ by UV-VIS, IR and EPR spectroelectrochemistry at variable temperatures. The construction of the novel UV-VIS-NIR-IR low-temperature OTTLE cell used in these studies is described in the last part of the paper.

The anions [(ZrOH(CO3)3)2]6− and [(ZrOH(C2O4)3)2]6−: single crystal X-ray diffraction studies of the complexes guanidinium zirconium carbonate [(C(NH2)3)3ZrOH(CO3)3·H2O]2 and sodium zirconium oxalate Na6(ZrOH(C2O4)3)2·7H2O

The complex [(C(NH2)3)3ZrOH(CO3)3·H2O]2 (A) has been shown by means of a single crystal X-ray diffraction study to contain [C(NH2)3]+ cations and dimeric anions of formulation [(ZrOH(CO3)3)2]6−. The anion is centrosymmetric with each metal being bonded to two bridging OH groups and three chelating CO2−3 ions. The Zr atoms are thus eight coordinate with a dodecahedral environments. The ZrO distances formed by the bridgng OH groups are shorter than those formed through zirconiu carbonate interactions. The non-bonded Zr…Zr distance is 3.47(2) Å. An infrared spectroscopic investigation of A provides data which support the findings of the crystallographic study. Likewise the complex Na6(ZrOH(CO2O4)3)2·7H2O (B) contains the anion [(ZrOH(C2O4)3)2]6−. This anion is structurally related to the anion in A as each Zr atom has an eight-coordinate dodecahedral environment being bonded to two bridging OH groups and three chelating oxalate ligands, but has no imposed crysallographic symmetry. The Zr…Zr non-bonded distance is 3.50(1) Å. The OZrO bridge angles are 69.7(4)° and A and 67.4(3)° in B.

Cocrystalline copolyimides of poly(ethylene 2,6-naphthalate)

Copolycondensation of N,N′-bis(2-hydroxyethyl)-biphenyl-3,4,3′,4′-tetracarboxylic diimide (5–25 mol %) with bis(2-hydroxyethyl)-2,6-naphthalate affords a series of cocrystalline, poly(ethylene 2,6-naphthalate) (PEN)-based poly(ester imide)s. The glass transition temperature rises with the level of comonomer, from 118 °C for PEN itself to 148 °C for the 25% diimide copolymer. X-ray powder and fiber diffraction studies show that, when 5 mol % or more of diimide is present, the α-PEN crystal structure is replaced by a new crystalline phase arising from isomorphic substitution of biphenyldiimide for PEN residues in the polymer crystal lattice. This new phase is provisionally identified as monoclinic, C2/m, with two chains per unit cell, a = 10.56, b = 6.74, c = 13.25 Å, and β = 143.0°.

Mesomorphic behaviour in copoly(ester-imide)s of poly(butylene-2,6-naphthalate) (PBN)

Copolycondensation of N,N’-bis(4-hydroxybutyl)-biphenyl-3,4,3',4'-tetracarboxylic diimide at 20 and 25 mol% with bis(4-hydroxybutyl)-2,6-naphthalate produces PBN-based copoly(ester-imide)s that not only crystallise but also form a (smectic) mesophase upon cooling from the melt. Incorporation of 25 mol% imide in PBN causes the glass transition temperature (measured by DSC) to rise from 51 to 74 °C, a significant increase relative to PBN. Furthermore, increased storage- (G'), loss- (G'') and elastic (E) moduli are observed for both copoly(ester-imide)s when compared to PBN itself. Structural analysis of the 20 mol% copolymer by X-ray powder and fibre diffraction, interfaced to computational modelling, suggests a crystal structure related to that of α-PBN, in space group P-1, with cell dimensions a = 4.74, b = 6.38, c = 14.45 Å, α = 106.1, β = 122.1, γ = 97.3°, ρ = 1.37 g cm-3.

Ultrasound promoted greener synthesis of 2-(3,5-diaryl-4,5-dihydro-1H-pyrazol-1-yl)-4-phenylthiazoles

A rapid and cleaner procedure for the synthesis of a series of 2-(3,5-diaryl-45-dihydro-1H-pyrazol-1-yl)-4-phenylthiazoles under ultrasonic irradiation in ethanol is described. (C) 2010 Elsevier B.V. All rights reserved.

Dessimetrização e enriquecimento enantiomérico de derivados do triciclo[5.2.1.0 2,6] decano através de enzimas e de indutores quirais. Preparação dos respectivos pseudopeptídeos restritos

Uma série de derivados quirais (e.e. > 99%) foram sintetizados a partir do meso- exo-(3R,5S)-3,5-dihidróximetilenotriciclo[5,2.1.02,6]decano com altos rendimentos, usando catálise enzimática (lipases) em reações de transesterificação. A resolução do respectivo diéster racêmico através da hidrólise catalisada com esterase (PLE) não forneceu o monoéster opticamente enriquecido; enquanto que a dessimetrização do anidrido usando indutores quirais (quinina e quinidina) resultou no monoéster opticamente enriquecido (e.e.≅ 60%). O respectivo amino-álcool protegido foi preparado. Alguns análogos inéditos de peptídeos restritos incorporados do triciclodecano foram sintetizados.

Síntese e caracterização do líquido iônico tetrafluoroborato de 1-metil-3-(2,6-(S)-dimetiloct-2-eno)-imidazol como eletrólito para produção de hidrogênio via eletrólise da água

Ionic liquids (ILs) are organic compounds liquid at room temperature, good electrical conductors, with the potential to form as a means for electrolyte on electrolysis of water, in which the electrodes would not be subjected to such extreme conditions demanding chemistry [1]. This paper describes the synthesis, characterization and study of the feasibility of ionic liquid ionic liquid 1-methyl-3(2,6-(S)-dimethyloct-2-ene)-imidazole tetrafluoroborate (MDI-BF4) as electrolyte to produce hydrogen through electrolysis of water. The MDI-BF4 synthesized was characterized by thermal methods of analysis (Thermogravimetric Analysis - TG and Differential Scanning Calorimetry - DSC), mid-infrared spectroscopy with Fourier transform by method of attenuated total reflectance (FTIR-ATR), nuclear magnetic resonance spectroscopy of hydrogen (NMR 1H) and cyclic voltammetry (CV). Where thermal methods were used to calculate the yield of the synthesis of MDI-BF4 which was 88.84%, characterized infrared spectroscopy functional groups of the compound and the binding B-F 1053 cm-1; the NMR 1H analyzed and compared with literature data defines the structure of MDI-BF4 and the current density achieved by MDI-BF4 in the voltammogram shows that the LI can conduct electrical current indicating that the MDI-BF4 is a good electrolyte, and that their behavior does not change with the increasing concentration of water

Stripping voltammetry of mercury(II) with a chemically modified carbon paste electrode containing silica gel functionalized with 2,5-dimercapto-1,3,4-thiadiazole

The accumulation voltammetry of mercury(II) was investigated at a carbon paste electrode chemically modified with silica gel functionalized with 2,5-dimercapto-1,3,4-thiadiazole (DTTPSG-CPE). The repetitive cyclic voltammogram of mercury(II) solution in the potential range -0.2 to +0.8 V (vs. Ag/AgCl), (0.02 mol L-1 KNO3; nu=20 mV s(-1)) show two peaks one at about 0.0 V and other at 0.31 V. However, the cathodic wave peak, around 0.0 V, is irregular and changes its form in each cycle. This peak at about 0.0 V is the reduction current for mercury(II) accumulated in the DTTPSG-CPE. The anodic wave peak at 0.31 V is well-defined and does not change during the cycles. The resultant material was characterized by cyclic and differential pulse anodic stripping voltammetry performed with the electrode in differents supporting electrolytes. The mercury response was evaluated with respect to pH, electrode composition, preconcentration time, mercury concentration, cleaning solution, possible interferences and other variables. The precision for six determinations (n=6) of 0.05 and 0.20 mg (L)-(1) Hg(II) was 2.8 and 2.2% (relative standard deviation), respectively. The method was satisfactory and used to determine the concentration of mercury(II) in natural waters contaminated by this metal.

2,6-Di-hidroxiacetofenona e tipo de corte basal no enraizamento de estacas semi-lenhosas de pessegueiro Okinawa

A propagação do pessegueiro (Prunus persica) no Brasil é baseada na enxertia sobre porta-enxertos oriundos de sementes. Outros métodos de propagação de frutíferas poderiam ser utilizados para o pessegueiro visando obtenção de materiais de melhor qualidade. Neste trabalho objetivou-se avaliar o efeito do 2,6-di-hidroxiacetofenona aplicado previamente ao ácido indol-butírico em estacas semi-lenhosas de pessegueiro da cultivar Okinawa preparadas com diferentes tipos de corte basal. Foram coletados ramos do porta-enxerto Okinawa em dezembro de 2001 para o preparo das estacas sem folhas, com 12cm de comprimento, 7mm de diâmetro, quatro gemas e diferentes tipos de cortes basais (corte longitudinal, corte lateral e corte da casca) tratado-as na base com 0 e 300mg L-1 de 2,6-di-hidroxiacetofenona por 4h em aeração (oxigenação) e depois com 2500mg L-1 ácido indol-butírico por 5s. As estacas foram plantadas em bandejas de poliestireno expandido (72 células) com vermiculita fina e colocadas em casa de nebulização por 45 dias. A aplicação de 300mg L-1 de 2,6-DHAP e a realização de lesões nas bases das estacas foram eficientes para aumentar o enraizamento das estacas semi-lenhosas do pessegueiro Okinawa , demonstrando que estas técnicas podem ser utilizadas para a propagação de pessegueiro por estaquia.

Crystal structure of 1,1,3-trimethyl-2-(2-(2,2,6-trimethyl-cyclohexyl)ethyl) cyclohexane, C20H34

C20H34, monoclinic, P12(1)/n1 (no. 14), a = 10.647(l) angstrom, b = 6.6844(9) angstrom, c = 11.723(1) angstrom, beta = 99.75(1)degrees, V = 822.3 angstrom(3) Z = 2, R-gt(F) = 0.043, wR(ref)(F-2) = 0.110, T = 93 K.

Factors which affect the catalytic activity of iron(III) meso tetrakis(2,6-dichlorophenyl)porphyrin chloride in homogeneous system

An optimization study of the reaction conditions of Fe(TDCPP)Cl when it is used as catalyst in the hydroxylation of cyclohexane by iodosylbenzene (PhIO) has been carried out, It was found that Fe(TDCPP)Cl follows the classical PhIO mechanism described for Fe(TPP)Cl, which involves the monomeric active species Fe-IV(O)P-+. (I). In the optimized condition ([Fe(TDCPP) = 3.0 X 10(-4) mol l(-1) in 1,2-dichloroethane (DCE); ultrasound stirring at 0 degrees C; PhIO/FeP molar ratio = 100), this FeP led to a yield of cyclohexanol (C-ol) of 96% and a turnover number of 96, Therefore, Fe(TDCPP)Cl may be considered a good biomimetic model and a very stable, resistant and selective catalyst, which yields C-ol as the sole product. DCE showed to be a better solvent than dichloromethane (DCM), 1 DCE:1 MeOH mixture or acetonitrile (ACN). Since the Fe-IV(O)P-+. is capable of abstracting hydrogen atom from DCM, MeOH or ACN, the solvent competes with the substrate. Presence of O-2 lowers the yield of C-ol, as it can further oxidize this alcohol to carboxylic acid in the presence of radicals, Presence of H2O also causes a decrease in the yield, since it converts the active species I into Fe-IV(OH)P, which cannot oxidize cyclohexane. Addition of excess imidazole or OH- to the system results in a decrease in the yield of C-ol, due to the formation of the hexacoordinated complexes Fe(TDCPP)Im(2)(+) (low-spin, beta(2) = 2.5 X 10(8) mol(-2) l(2)) and Fe(TDCPP)(OH)(2)(-) (high-spin, beta(2) = 6.3 X 10(7) mol(-2) l(2)), the formation of both Fe(TDCPP)Im(2)(+) and Fe(TDCPP)(OH)(2)(-) complexes were confirmed by EPR studies. The catalytic activities of Fe(TDCPP)C and Fe(TFPP)Cl were compared, the unusually high yields of C-ol with Fe(TFPP)Cl obtained when ultrasound, DCM and O-2 atmosphere were used, suggest that a parallel mechanism involving the mu-oxo dimer form, O-2 and radicals may also be occurring with this FeP, besides the PhIO mechanism.