Effect of the application of different water depths and nitrogen and potassium doses on quality of Tanzania grass

The objective of this study was to evaluate the effects of the application of different water depths and nitrogen and potassium doses in the quality of Tanzania grass, in the southern of the state of Tocantins. The experiment was conducted on strips of traditional sprinklers, and used, as treatments, a mixture of fertilizer combinations of N and K2O always in the ratio of 1 N:0.8 K2O. This study determined throughout the experiment: plant height (PH), the crude protein (CP) and neutral detergent fiber (NDF). The highest plant height obtained was 132.4 cm, with a fertilizer dose of 691.71 kg ha-1 in the proportion of N:0.8 K2O, in other words, 384.28 kg ha-1 of N and 307.43 kg ha-1 of K2O, and water depth of 80% of the ETc. The highest crude protein content was 12.2%, with the fertilizer dose application of 700 kg ha-1 yr-1 in the proportion of 1 N to 0.8 of K2O, in other words, 388.89 kg ha-1 of N and 311.11 kg ha-1 of K2O and absence of irrigation. The lowest level of neutral detergent fiber was 60.7% with the application of the smallest dose of fertilizer and highest water depth. It was concluded in this study that there was an increase in plant height by increasing the fertilizer dose and water depth. The crude protein content increased 5.4% in the dry season, by increasing the fertilizer dose and water depth. In the dry season, there was an increase of NDF content by 4.5% by increasing the application of fertilizer and water depth.

Estimated production and evapotranspiration of irrigated bean cultivars

The current study intended to determine the optimum water depth, yield and evapotranspiration (ETc) for bean cultivars. The experiment was conducted in the Campus of Unit I of the Triângulo Mineiro Federal Education and Technology Institute in Uberaba, MG, in a completely randomized design with three replications. The treatments consisted of four water-replacing levels in the soil (70, 100, 130 and 160% of the crop evapotranspiration) and four bean cultivars (Pérola, BRSMG Madrepérola, BRSMG Majestoso and IAC Alvorada). The average values of ETc obtained for soil water balance for the cultivars Pérola, BRSMG Madrepérola, BRSMG Majestoso and IAC Alvorada were, respectively, of 5.25 mm day-1, 4.59 mm day-1, 4.54 mm day-1 and 4.77 mm day-1. The water depths which provided the highest yields were for the cultivars Pérola, BRSMG Madrepérola, BRSMG Majestoso and IAC Alvorada of 451.61 mm, 454.41 mm, 504.71 mm and 344.30 mm, respectively. The maximum yields found were 4597.87 kg ha-1 (Pérola), 4546.27 kg ha-1 (BRSMG Madrepérola), 4253.39 kg ha-1 (BRSMG Majestoso) and 3958.50kg ha-1 (IAC Alvorada).

Drip pulses and soil mulching effect on american crisphead lettuce yield

ABSTRACT An experiment was conducted in a greenhouse at the Federal University of Lavras cultivated with American lettuce, cv. Raider-Plus. The aim of this study was to evaluate the effects of irrigation water depths applied by drip pulses and of soil coverage on crop yields and efficiency of water use. The experimental design used was randomized blocks with eight treatments and three replications, totaling twenty-four plots. The treatments consisted of soil with and without coverage (double-sided white and black plastic) associated with four irrigation management levels. Irrigation management consisted in reposition of irrigation depths based on crop evapotranspiration (ETc) with D1-100% of ETc, applied continuously (control), and D2 - 100% of ETc, D3 - 75% of ETc, and D4-50% of ETc, applied by pulses. Irrigation by pulses consisted in splitting the depths into six irrigation pulses with intervals of fifty minutes of rest. It was observed that pulse irrigation saved 25% of water in treatment without mulching and 50% when plastic mulching was used, contributing substantially to improve irrigation water efficiency.

Pressurized hot water flow-through extraction of birch wood

Effective processes to fractionate the main compounds in biomass, such as wood, are a prerequisite for an effective biorefinery. Water is environmentally friendly and widely used in industry, which makes it a potential solvent also for forest biomass. At elevated temperatures over 100 °C, water can readily hydrolyse and dissolve hemicelluloses from biomass. In this work, birch sawdust was extracted using pressurized hot water (PHWE) flow-through systems. The hypothesis of the work was that it is possible to obtain polymeric, water-soluble hemicelluloses from birch sawdust using flow-through PHW extractions at both laboratory and large scale. Different extraction temperatures in the range 140–200 °C were evaluated to see the effect of temperature to the xylan yield. The yields and extracted hemicelluloses were analysed to obtain sugar ratios, the amount of acetyl groups, furfurals and the xylan yields. Higher extraction temperatures increased the xylan yield, but decreased the molar mass of the dissolved xylan. As the extraction temperature increased, more acetic acid was released from the hemicelluloses, thus further decreasing the pH of the extract. There were only trace amounts of furfurals present after the extractions, indicating that the treatment was mild enough not to degrade the sugars further. The sawdust extraction density was increased by packing more sawdust in the laboratory scale extraction vessel. The aim was to obtain extracts with higher concentration than in typical extraction densities. The extraction times and water flow rates were kept constant during these extractions. The higher sawdust packing degree decreased the water use in the extractions and the extracts had higher hemicellulose concentrations than extractions with lower sawdust degrees of packing. The molar masses of the hemicelluloses were similar in higher packing degrees and in the degrees of packing that were used in typical PHWE flow-through extractions. The structure of extracted sawdust was investigated using small angle-(SAXS) and wide angle (WAXS) x-ray scattering. The cell wall topography of birch sawdust and extracted sawdust was compared using x-ray tomography. The results showed that the structure of the cell walls of extracted birch sawdust was preserved but the cell walls were thinner after the extractions. Larger pores were opened inside the fibres and cellulose microfibrils were more tightly packed after the extraction. Acetate buffers were used to control the pH of the extracts during the extractions. The pH control prevented excessive xylan hydrolysis and increased the molar masses of the extracted xylans. The yields of buffered extractions were lower than for plain water extractions at 160–170 °C, but at 180 °C yields were similar to those from plain water and pH buffers. The pH can thus be controlled during extraction with acetate buffer to obtain xylan with higher molar mass than those obtainable using plain water. Birch sawdust was extracted both in the laboratory and pilot scale. The performance of the PHWE flow-through system was evaluated in the laboratory and the pilot scale using vessels with the same shape but different volumes, with the same relative water flow through the sawdust bed, and in the same extraction temperature. Pre-steaming improved the extraction efficiency and the water flow through the sawdust bed. The extracted birch sawdust and the extracted xylan were similar in both laboratory and pilot scale. The PHWE system was successfully scaled up by a factor of 6000 from the laboratory to pilot scale and extractions performed equally well in both scales. The results show that a flow-through system can be further scaled up and used to extract water-soluble xylans from birch sawdust. Extracted xylans can be concentrated, purified, and then used in e.g. films and barriers, or as building blocks for novel material applications.

Evaluation of water retention capacity and flood control function of the forest catchment

This research quantitatively evaluates the water retention capacity and flood control function of the forest catchments by using hydrological data of the large flood events which happened after the serious droughts. The objective sites are the Oodo Dam and the Sameura Dam catchments in Japan. The kinematic wave model, which considers saturated and unsaturated sub-surface soil zones, is used for the rainfall-runoff analysis. The result shows that possible storage volume of the Oodo Dam catchment is 162.26 MCM in 2005, while that of Samerua is 102.83 MCM in 2005 and 102.64 MCM in 2007. Flood control function of the Oodo Dam catchment is 173 mm in water depth in 2005, while the Sameura Dam catchment 114 mm in 2005 and 126 mm in 2007. This indicates that the Oodo Dam catchment has more than twice as big water capacity as its capacity (78.4 mm), while the Sameura Dam catchment has about one-fifth of the its storage capacity (693 mm).

Irrigation performance and gross water productivity in furrow-irrigated ornamental tree production

In the ornamental plant production region of Girona (Spain), which is one of the largest of its kind in southern Europe, most of the surface is irrigated using wide blocked-end furrows. The objectives of this paper were: (1) to evaluate the irrigation scheduling methods used by ornamental plant producers; (2) to analyse different scenarios in order to assess how they affect irrigation performance; (3) to evaluate the risk of deep percolation; and (4) to calculate gross water productivity. A two-year study in a representative commercial field, planted with Prunus cerasifera ‘Nigra’, was carried out. The irrigation dose applied by the farmers was slightly smaller than the required water dose estimated by the use of two different methods: the first based on soil water content, and the second based on evapotranspiration. Distribution uniformity and application efficiency were high, with mean values above 87%. Soil water content measurements revealed that even at the end of the furrow, where the infiltrated water depth was greatest, more than 90% of the infiltrated water was retained in the shallowest 40 cm of the soil; accordingly, the risk of water loss due to deep percolation was minimal. Gross water productivity for ornamental tree production was € 11.70 m–3, approximately 20 times higher than that obtained with maize in the same region

Geochemistry of iron and manganese in soils and sediments of a mangrove system, Island of Pai Matos (Cananeia - SP, Brazil)

Five zones along a transect of 180 m were selected for study on the Island of Pai Matos (Sao Paulo, Brazil). Four of the zones are colonised by vascular plants (Spartina SP, Laguncularia LG, Avicennia AV and Rhizophora RH) and were denominated soils, and the other zone, which lacks vegetation, was denominated sediment (SD). The geochemical conditions differed significantly in soils and sediment and also at different depths. The soils were oxic (Eh > 350 mV) or suboxic (Eh: 350-100 mV) at the surface and anoxic (Eh < 100 mV) at depth, whereas in the sediment anoxic conditions prevailed at all depths, but with a lower concentration of sulphides in the pore water and pyrite in the solid fraction. Under these geochemical conditions Fe is retained in the soils, while the Mn tends to be mobilized and lost. The most abundant form of iron oxyhydroxide was lepidocrocite (mean concentration for all sites and depths, 45 +/- 19 mu mol g(-1)), followed by goethite (30 19 mu mol g(-1))and ferrihydrite (19 +/- 11 mu mol g(-1)),with significant differences among the mean concentrations. There was a significant decrease with depth in all the types of Fe oxyhydroxides measured, particularly the poorly crystalline forms. The pyrite fraction was an important component of the free Fe pool (non-silicate Fe) in all soils as well as in the sediment, especially below 20 cm depth (mean concentration for all sites and depths, 60 +/- 54 mu mol CI). Furthermore, the mean concentration of Fe-pyrite for all sites and depths was higher than that obtained for any of the three Fe oxyhydroxides measured. The Fe-AVS was a minor fraction, indicating that the high concentrations of dissolved Fe in the soils in the upper area of the transect result from the oxidation of Fe sulphides during low tide. Mossbauer spectroscopy also revealed that most of the Fe (III) was associated with silicates, in this case nontronite. The presence of crystals of pyrite associated with phyllosilicates in samples from the upper layer of the soils may indicate that pyritization of this form of Fe(III) is more rapid than usually reported for ocean bed sediments. The sequential extraction of Mn did not reveal any clearly dominant fraction, with the Mn-carbonate fraction being the most prevalent, followed by exchangeable Mn and oxides of Mn, whereas pyrite-Mn and Mn associated with crystalline Fe-oxides were present at significantly lower concentrations. The high concentration of dissolved Mn found in the soils in the lower part of the transect is consistent with the fact that the solubility is determined by the carbonate fraction. Unlike for Fe, in the soils in the higher zone, which are subject to intense drainage during low tide, there was loss of Mn, as reflected by the concentration of total Mn. (C) 2008 Elsevier B.V. All rights reserved.

City Of Toronto’S Approach On Implementing The New Federal Wastewater Effluent Regulations Using A GIS-Based Hydrologic And Hydraulic Model

Canada releases over 150 billion litres of untreated and undertreated wastewater into the water environment every year1. To clean up urban wastewater, new Federal Wastewater Systems Effluent Regulations (WSER) on establishing national baseline effluent quality standards that are achievable through secondary wastewater treatment were enacted on July 18, 2012. With respect to the wastewater from the combined sewer overflows (CSO), the Regulations require the municipalities to report the annual quantity and frequency of effluent discharges. The City of Toronto currently has about 300 CSO locations within an area of approximately 16,550 hectares. The total sewer length of the CSO area is about 3,450 km and the number of sewer manholes is about 51,100. A system-wide monitoring of all CSO locations has never been undertaken due to the cost and practicality. Instead, the City has relied on estimation methods and modelling approaches in the past to allow funds that would otherwise be used for monitoring to be applied to the reduction of the impacts of the CSOs. To fulfill the WSER requirements, the City is now undertaking a study in which GIS-based hydrologic and hydraulic modelling is the approach. Results show the usefulness of this for 1) determining the flows contributing to the combined sewer system in the local and trunk sewers for dry weather flow, wet weather flow, and snowmelt conditions; 2) assessing hydraulic grade line and surface water depth in all the local and trunk sewers under heavy rain events; 3) analysis of local and trunk sewer capacities for future growth; and 4) reporting of the annual quantity and frequency of CSOs as per the requirements in the new Regulations. This modelling approach has also allowed funds to be applied toward reducing and ultimately eliminating the adverse impacts of CSOs rather than expending resources on unnecessary and costly monitoring.

Efeito de concentrações de herbicidas sobre aspectos biológicos de Fusarium sp. (isolado FCAV#940)

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Application technology for the entomopathogenic nematodes Heterorhabditis indica and Steinernema sp. (Rhabditida: Heterorhabditidae and Steinernematidae) to control Spodoptera frugiperda (Smith) (Lepidoptera: Noctuidae) in corn

O efeito de diversas tecnologias de aplicação foi avaliado sobre a concentração, viabilidade e eficácia dos juvenis infectantes dos nematóides Heterorhabditis indica Poinar, Karunakar & David (IBCB-n5) e Steinernema sp. (IBCB-n6) no controle da lagarta-do-cartucho Spodoptera frugiperda Smith na cultura do milho. Para o controle da lagarta-do-cartucho no terceiro estádio em placas de Petri foram necessários 280 juvenis infectantes de Steinernema sp., enquanto que 400 juvenis infectantes de H. indica controlaram apenas 75% das lagartas. Podem-se pulverizar os entomopatógenos, sem que haja perda significativa na sua concentração e viabilidade, com equipamentos que forneçam carga elétrica à calda, ponta centrífuga e pontas hidráulicas. Entretanto, o emprego de pulverizadores com pontas que requerem elementos filtrantes com malha igual a 100 resultou em decréscimo na concentração de juvenis infectantes de H. indica e Steinernema sp., de 28% e 53%, respectivamente. Os tensoativos organosiliconado e etoxilados não afetaram a viabilidade dos juvenis infectantes de Steinernema sp. Nos experimentos de pulverização em plantas de milho (V6) com Steinernema sp., doses equivalentes a até 288 milhões de juvenis infectantes por hectare, diluídos em volume de calda de até 800 L ha-1 com 0,01 % do tensoativo etoxilado, ou nesse volume seguido de exposição a chuva artificial (lâmina de água de 6 mm), não foram suficientes para o controle de S. frugiperda em casa-de-vegetação.

Potencial de lixiviação de herbicidas utilizados na cultura do algodão em colunas de solo

O intenso uso de herbicidas implica a necessidade de determinar o potencial dessas substâncias em contaminar fontes aquáticas subsuperficiais. Diante dessa preocupação, o objetivo deste trabalho foi avaliar o efeito de diferentes lâminas de água sobre o potencial de lixiviação de quatro herbicidas utilizados em pré-emergência na cultura do algodão, em dois solos provenientes de Campo Novo do Parecis-MT (RQ - textura arenosa) e Tangará da Serra-MT (LV - textura argilosa). No desenvolvimento deste trabalho utilizouse a técnica de bioensaio em colunas de solo, nas quais foram simuladas irrigações de 0, 20, 40, 60, 80 e 100 mm, após a aplicação de alachlor (RQ 2,40; LV 3,36 kg ha-1), oxyfluorfen (RQ 0,48; LV 0,72 kg ha-1), prometryne (RQ 0,75; LV 1,50 kg ha-1) e S-metolachlor (RQ 1,20; LV 1,44 kg ha-1). Nas amostras de solo com textura arenosa (RQ), evidenciou-se que lâminas de 80 e 100 mm de água proporcionaram lixiviação até a profundidade de 10-15 cm do alachlor e até 15-20 cm do S-metolachlor. Independentemente da lâmina de água aplicada, nas amostras de RQ oxyfluorfen não ultrapassou a camada de 5-10 cm, e o prometryne movimentou-se até a camada de 10-15 cm somente na lâmina de 100 mm de água. Nas amostras de solo com textura argilosa (LV), o oxyfluorfen não se movimentou além da camada superficial, mesmo sob as maiores lâminas de irrigação, e o prometryne atingiu 5-10 cm de profundidade sob lâminas de 80 e 100 mm. Os herbicidas alachlor e S-metolachlor atingiram 10-15 cm de profundidade sob lâminas de 80 e 100 mm no LV. Evidenciou-se uma maior movimentação efetiva das moléculas de herbicidas nas amostras de solo com textura arenosa (RQ), em relação às amostras de solo com textura argilosa (LV).

Consumo e custo de energia elétrica na cultura de citros irrigado por gotejamento e microaspersão, com três lâminas de água

The objective of this work was to analyze the consumption, electric energy cost, and economic results of irrigated citrus (Citrus sinensis). The treatments consisted of a dripping irrigation system with one and two lateral distribution lines, a micro sprinkler irrigation system and a treatment without irrigation. For each irrigation system, three water depths were used: 100%, 75% and 50% of Etc (citrus evapotranspiration). The electric energy cost for two tariff groups, Group A and Group B, was studied. For Group A, the expenses with energy were determined for the Conventional Binomial Structure tariff, the Hour-seasonal tariff (green and blue) and the special tariff for nocturnal irrigation. The kWh cost for the tariff systems were obtained from the website of CPFL (São Paulo State Power and Light Company, Brazil). The best relation between the electric energy consumption (kWh.ha -1) and productivity (t.ha -1) occurred in the treatment irrigated with 50% of the Etc. The irrigated treatments increased productivity. The biggest productivity was observed in the irrigation treatments with 50% of the Etc when compared to the ones with 100% of the Etc. The blue and green Hour-seasonal tariff system of Group A (nocturnal irrigation) was the best option. A biggest economic turnover occurred in the treatments irrigated with 50% of the Etc.

Produção e Qualidade Física dos Frutos do Abacaxi sob Diferentes Lâminas e Frequências de Irrigação

The objective of this study was to evaluate the performance of pineapple cultivar Smooth Cayenne as the physical production and the quality of the fruit when subjected to different frequencies of water dpeth and soil water in Triângulo Mineiro - Uberaba-MG. The experimental area soil is Oxisol, clay loam sandy and soft undulating local relief. A randomized block design in a factorial 4 x 2 with four levels of soil water depth (50%, 75%, 100% and 125%) of crop evapotranspiration (ETc) and two irrigation frequencies (1 day and 3 days = F1 = F2) and four replications was utilized. The crop productivity, number of seedlings, mean weight, diameter, and hardness of the fruit, plus water use efficiency were evaluated. Productivity was not significantly affected by the water depth and by the frequency of water applied; however the fruit shell resistance, the efficiency of water use, and ratoon seedlings were significantly influenced by irrigation, the water depth of 50% of the crop evapotranspiration (ETC) provided greater efficiency of water use for the production of pineapple fruit.

Crescimento da grama bermudas sob diferentes lâminas de irrigação

The objective of the present study was to analyze the most appropriate water depth for maintaining a good quality of Bermudas Grass (Cynodon dactylon) for soccer fields while saving water and electrical resources. Four treatments were used: T1 - irrigated with a water depth of 50% of evapotranspiration (ETo), T2 - irrigated with a water depth of 75% of ETo, T3 - irrigated with a water depth of 100% of ETo and T4 - irrigated with a water depth of 150% of ETo, all treatments were irrigated daily. The reference ETo was obtained by the Penman-Monteith method. The study was conducted in an experimental area of the Instituto Federal de Educação, Ciência e Tecnologia do Triângulo Mineiro - Campus Uberaba, Uberaba, Minas Gerais, Brazil, from June to September 2010 and from January to March 2011. Three evaluations of the variables were performed during the experimental period. The samples were obtained with the help of a cylindrical extractor with 10 cm in diameter and 30 cm in height. In each sample height and dry organic matter (leaf, root and organic material) were analyzed. The experimental design was randomized block with four treatments in five blocks. No significant differences were observed for dry matter and height (roots and organic material). The best results were those for T4 which obtained the greatest height.

Estudo da porção offshore da bacia do Benin e o seu potencial no armazenamento de hidrocarbonetos, margem equatorial africana

Pós-graduação em Geologia Regional - IGCE