Difference between satellite microwave systems and "in situ" soil moisture data

p.33-44

Design and testing of innovative, artificial intelligence-based techniques to model and control the combustion process and to reduce the Co2 emissions in modern, high-performance, gasoline direct injection engines

This work deals with the development of calibration procedures and control systems to improve the performance and efficiency of modern spark ignition turbocharged engines. The algorithms developed are used to optimize and manage the spark advance and the air-to-fuel ratio to control the knock and the exhaust gas temperature at the turbine inlet. The described work falls within the activity that the research group started in the previous years with the industrial partner Ferrari S.p.a. . The first chapter deals with the development of a control-oriented engine simulator based on a neural network approach, with which the main combustion indexes can be simulated. The second chapter deals with the development of a procedure to calibrate offline the spark advance and the air-to-fuel ratio to run the engine under knock-limited conditions and with the maximum admissible exhaust gas temperature at the turbine inlet. This procedure is then converted into a model-based control system and validated with a Software in the Loop approach using the engine simulator developed in the first chapter. Finally, it is implemented in a rapid control prototyping hardware to manage the combustion in steady-state and transient operating conditions at the test bench. The third chapter deals with the study of an innovative and cheap sensor for the in-cylinder pressure measurement, which is a piezoelectric washer that can be installed between the spark plug and the engine head. The signal generated by this kind of sensor is studied, developing a specific algorithm to adjust the value of the knock index in real-time. Finally, with the engine simulator developed in the first chapter, it is demonstrated that the innovative sensor can be coupled with the control system described in the second chapter and that the performance obtained could be the same reachable with the standard in-cylinder pressure sensors.

Development and testing of methodologies for the control and diagnosis of innovative combustion systems

In pursuit of aligning with the European Union's ambitious target of achieving a carbon-neutral economy by 2050, researchers, vehicle manufacturers, and original equipment manufacturers have been at the forefront of exploring cutting-edge technologies for internal combustion engines. The introduction of these technologies has significantly increased the effort required to calibrate the models implemented in the engine control units. Consequently the development of tools that reduce costs and the time required during the experimental phases, has become imperative. Additionally, to comply with ever-stricter limits on 〖"CO" 〗_"2" emissions, it is crucial to develop advanced control systems that enhance traditional engine management systems in order to reduce fuel consumption. Furthermore, the introduction of new homologation cycles, such as the real driving emissions cycle, compels manufacturers to bridge the gap between engine operation in laboratory tests and real-world conditions. Within this context, this thesis showcases the performance and cost benefits achievable through the implementation of an auto-adaptive closed-loop control system, leveraging in-cylinder pressure sensors in a heavy-duty diesel engine designed for mining applications. Additionally, the thesis explores the promising prospect of real-time self-adaptive machine learning models, particularly neural networks, to develop an automatic system, using in-cylinder pressure sensors for the precise calibration of the target combustion phase and optimal spark advance in a spark-ignition engines. To facilitate the application of these combustion process feedback-based algorithms in production applications, the thesis discusses the results obtained from the development of a cost-effective sensor for indirect cylinder pressure measurement. Finally, to ensure the quality control of the proposed affordable sensor, the thesis provides a comprehensive account of the design and validation process for a piezoelectric washer test system.

The Value of Knowing: Public Perceptions about Alzheimers and testing

����This survey commissioned by Alzheimer Europe��examined public perception and awareness of Alzheimer’s disease and aimed to identify the views of the general public on the value of diagnosis. The survey of 2,678 people was designed and analysed by the Harvard School of Public Health and Alzheimer Europe. Fieldwork was conducted via telephone (landline and cell phone) with nationally representative random samples of adults age 18 and older in five countries by TNS, an independent research company based in London. Countries surveyed were the USA, Germany, France, Spain and Poland. The survey was supported by a grant to Alzheimer Europe from Bayer AG. Bayer was not involved in the design of the survey or the analysis of the findings.��Full details of the survey results are available on the AE website at: http://www.alzheimer-europe.org/EN/Research��Alzheimer Europe is the umbrella organisation of national Alzheimer associations and currently has 31 member organisations in 27 European countries. The mission statement of the organisation is to change perceptions, practice and policy to ensure equal access of people with dementia to a high level of care services and treatment options.����

Requirements definition and testing of the new version of multi-mission generic monitoring system (GEMS) v 4.4 for operations at Eumetsat

EUMETSAT (www.eumetsat.int) e’ l’agenzia europea per operazioni su satelliti per monitorare clima, meteo e ambiente terrestre. Dal centro operativo situato a Darmstadt (Germania), si controllano satelliti meteorologici su orbite geostazionarie e polari che raccolgono dati per l’osservazione dell’atmosfera, degli oceani e della superficie terrestre per un servizio continuo di 24/7. Un sistema di monitoraggio centralizzato per programmi diversi all’interno dell’ambiente operazionale di EUMETSAT, e’ dato da GEMS (Generic Event Monitoring System). Il software garantisce il controllo di diverse piattaforme, cross-monitoring di diverse sezioni operative, ed ha le caratteristiche per potere essere esteso a future missioni. L’attuale versione della GEMS MMI (Multi Media Interface), v. 3.6, utilizza standard Java Server Pages (JSP) e fa uso pesante di codici Java; utilizza inoltre files ASCII per filtri e display dei dati. Conseguenza diretta e’ ad esempio, il fatto che le informazioni non sono automaticamente aggiornate, ma hanno bisogno di ricaricare la pagina. Ulteriori inputs per una nuova versione della GEMS MMI vengono da diversi comportamenti anomali riportati durante l’uso quotidiano del software. La tesi si concentra sulla definizione di nuovi requisiti per una nuova versione della GEMS MMI (v. 4.4) da parte della divisione ingegneristica e di manutenzione di operazioni di EUMETSAT. Per le attivita’ di supporto, i test sono stati condotti presso Solenix. Il nuovo software permettera’ una migliore applicazione web, con tempi di risposta piu’ rapidi, aggiornamento delle informazioni automatico, utilizzo totale del database di GEMS e le capacita’ di filtri, insieme ad applicazioni per telefoni cellulari per il supporto delle attivita’ di reperibilita’. La nuova versione di GEMS avra’ una nuova Graphical User Interface (GUI) che utilizza tecnologie moderne. Per un ambiente di operazioni come e’ quello di EUMETSAT, dove l’affidabilita’ delle tecnologie e la longevita’ dell’approccio scelto sono di vitale importanza, non tutti gli attuali strumenti a disposizione sono adatti e hanno bisogno di essere migliorati. Allo stesso tempo, un’ interfaccia moderna, in termini di visual design, interattivita’ e funzionalita’, e’ importante per la nuova GEMS MMI.

Firmware development and testing for L1/L2 IBL upgrade

Il lavoro di questa tesi riguarda principalmente l'upgrade, la simulazione e il test di schede VME chiamate ReadOut Driver (ROD), che sono parte della catena di elaborazione ed acquisizione dati di IBL (Insertable B-Layer). IBL è il nuovo componente del Pixel Detector dell'esperimento ATLAS al Cern che è stato inserito nel detector durante lo shut down di LHC; fino al 2012 infatti il Pixel Detector era costituito da tre layer, chiamati (partendo dal più interno): Barrel Layer 0, Layer 1 e Layer 2. Tuttavia, l'aumento di luminosità di LHC, l'invecchiamento dei pixel e la richiesta di avere misure sempre più precise, portarono alla necessità di migliorare il rivelatore. Così, a partire dall'inizio del 2013, IBL (che fino a quel momento era stato un progetto sviluppato e finanziato separatamente dal Pixel Detector) è diventato parte del Pixel Detector di ATLAS ed è stato installato tra la beam-pipe e il layer B0. Questa tesi fornirà innanzitutto una panoramica generale dell'esperimento ATLAS al CERN, includendo aspetti sia fisici sia tecnici, poi tratterà in dettaglio le varie parti del rivelatore, con particolare attenzione su Insertable B-Layer. Su quest'ultimo punto la tesi si focalizzerà sui motivi che ne hanno portato alla costruzione, sugli aspetti di design, sulle tecnologie utilizzate (volte a rendere nel miglior modo possibile compatibili IBL e il resto del Pixel Detector) e sulle scelte di sviluppo e fabbricazione. La tesi tratterà poi la catena di read-out dei dati, descrivendo le tecniche di interfacciamento con i chip di front-end, ed in particolare si concentrerà sul lavoro svolto per l'upgrade e lo sviluppo delle schede ReadOut Drivers (ROD) introducendo le migliorie da me apportate, volte a eliminare eventuali difetti, migliorare le prestazioni ed a predisporre il sistema ad una analisi prestazionale del rivelatore. Allo stato attuale le schede sono state prodotte e montate e sono già parte del sistema di acquisizione dati del Pixel Detector di ATLAS, ma il firmware è in continuo aggiornamento. Il mio lavoro si è principalmente focalizzato sul debugging e il miglioramento delle schede ROD; in particolare ho aggiunto due features: - programmazione parallela delle FPGA} delle ROD via VME. IBL richiede l'utilizzo di 15 schede ROD e programmandole tutte insieme (invece che una alla volta) porta ad un sensibile guadagno nei tempi di programmazione. Questo è utile soprattutto in fase di test; - reset del Phase-Locked Loop (PLL)} tramite VME. Il PLL è un chip presente nelle ROD che distribuisce il clock a tutte le componenti della scheda. Avere la possibilità di resettare questo chip da remoto permette di risolvere problemi di sincronizzazione. Le ReadOut Driver saranno inoltre utilizzate da più layer del Pixel Detector. Infatti oltre ad IBL anche i dati provenienti dai layer 1 e 2 dei sensori a pixel dell’esperimento ATLAS verranno acquisiti sfruttando la catena hardware progettata, realizzata e testata a Bologna.

Screening and testing for endocrine disruption in fish-biomarkers as "signposts," not "traffic lights," in risk assessment

Biomarkers are currently best used as mechanistic "signposts" rather than as "traffic lights" in the environmental risk assessment of endocrine-disrupting chemicals (EDCs). In field studies, biomarkers of exposure [e.g., vitellogenin (VTG) induction in male fish] are powerful tools for tracking single substances and mixtures of concern. Biomarkers also provide linkage between field and laboratory data, thereby playing an important role in directing the need for and design of fish chronic tests for EDCs. It is the adverse effect end points (e.g., altered development, growth, and/or reproduction) from such tests that are most valuable for calculating adverseNOEC (no observed effect concentration) or adverseEC10 (effective concentration for a 10% response) and subsequently deriving predicted no effect concentrations (PNECs). With current uncertainties, biomarkerNOEC or biomarkerEC10 data should not be used in isolation to derive PNECs. In the future, however, there may be scope to increasingly use biomarker data in environmental decision making, if plausible linkages can be made across levels of organization such that adverse outcomes might be envisaged relative to biomarker responses. For biomarkers to fulfil their potential, they should be mechanistically relevant and reproducible (as measured by interlaboratory comparisons of the same protocol). VTG is a good example of such a biomarker in that it provides an insight to the mode of action (estrogenicity) that is vital to fish reproductive health. Interlaboratory reproducibility data for VTG are also encouraging; recent comparisons (using the same immunoassay protocol) have provided coefficients of variation (CVs) of 38-55% (comparable to published CVs of 19-58% for fish survival and growth end points used in regulatory test guidelines). While concern over environmental xenoestrogens has led to the evaluation of reproductive biomarkers in fish, it must be remembered that many substances act via diverse mechanisms of action such that the environmental risk assessment for EDCs is a broad and complex issue. Also, biomarkers such as secondary sexual characteristics, gonadosomatic indices, plasma steroids, and gonadal histology have significant potential for guiding interspecies assessments of EDCs and designing fish chronic tests. To strengthen the utility of EDC biomarkers in fish, we need to establish a historical control database (also considering natural variability) to help differentiate between statistically detectable versus biologically significant responses. In conclusion, as research continues to develop a range of useful EDC biomarkers, environmental decision-making needs to move forward, and it is proposed that the "biomarkers as signposts" approach is a pragmatic way forward in the current risk assessment of EDCs.

On the specification and testing of inverters for stand-alone PV systems

Inverter features are reviewed from a PV systems perspective, with a view to contributing to possible codes, procurement specifications and testing procedures, in order to assure the technical quality of these systems. A laboratory testing campaign has been carried out on a representative set of sixteen currently available inverters and a set of the most common AC appliances. The results of the tests are discussed with the aim of divulging the particular features of operating AC appliances in PV systems and the provisions to be taken into account in PV system design. The development of testing procedures has followed the motto ?keep it as simple as possible?, in order to make their application easier in conventional laboratories in developing countries.

Development and testing of a link from HP calculator to PDP11. Final report.

National Highway Traffic Safety Administration, Vehicle Research and Test Center, East Liberty, Ohio

Successful development and testing of a Method for Aggregating The Reporting of Interventions in Complex Studies (MATRICS)

Objectives: To develop a tool for the accurate reporting and aggregation of findings from each of the multiple methods used in a complex evaluation in an unbiased way. Study Design and Setting: We developed a Method for Aggregating The Reporting of Interventions in Complex Studies (MATRICS) within a gastroenterology study [Evaluating New Innovations in (the delivery and organisation of) Gastrointestinal (GI) endoscopy services by the NHS Modernisation Agency (ENIGMA)]. We subsequently tested it on a different gastroenterology trial [Multi-Institutional Nurse Endoscopy Trial (MINuET)]. We created three layers to define the effects, methods, and findings from ENIGMA. We assigned numbers to each effect in layer 1 and letters to each method in layer 2. We used an alphanumeric code based on layers 1 and 2 to every finding in layer 3 to link the aims, methods, and findings. We illustrated analogous findings by assigning more than one alphanumeric code to a finding. We also showed that more than one effect or method could report the same finding. We presented contradictory findings by listing them in adjacent rows of the MATRICS. Results: MATRICS was useful for the effective synthesis and presentation of findings of the multiple methods from ENIGMA. We subsequently successfully tested it by applying it to the MINuET trial. Conclusion: MATRICS is effective for synthesizing the findings of complex, multiple-method studies.

Formal verification and testing of software architectural models

Ensuring the correctness of software has been the major motivation in software research, constituting a Grand Challenge. Due to its impact in the final implementation, one critical aspect of software is its architectural design. By guaranteeing a correct architectural design, major and costly flaws can be caught early on in the development cycle. Software architecture design has received a lot of attention in the past years, with several methods, techniques and tools developed. However, there is still more to be done, such as providing adequate formal analysis of software architectures. On these regards, a framework to ensure system dependability from design to implementation has been developed at FIU (Florida International University). This framework is based on SAM (Software Architecture Model), an ADL (Architecture Description Language), that allows hierarchical compositions of components and connectors, defines an architectural modeling language for the behavior of components and connectors, and provides a specification language for the behavioral properties. The behavioral model of a SAM model is expressed in the form of Petri nets and the properties in first order linear temporal logic.^ This dissertation presents a formal verification and testing approach to guarantee the correctness of Software Architectures. The Software Architectures studied are expressed in SAM. For the formal verification approach, the technique applied was model checking and the model checker of choice was Spin. As part of the approach, a SAM model is formally translated to a model in the input language of Spin and verified for its correctness with respect to temporal properties. In terms of testing, a testing approach for SAM architectures was defined which includes the evaluation of test cases based on Petri net testing theory to be used in the testing process at the design level. Additionally, the information at the design level is used to derive test cases for the implementation level. Finally, a modeling and analysis tool (SAM tool) was implemented to help support the design and analysis of SAM models. The results show the applicability of the approach to testing and verification of SAM models with the aid of the SAM tool.^

Formal verification and testing of software architectural models

Ensuring the correctness of software has been the major motivation in software research, constituting a Grand Challenge. Due to its impact in the final implementation, one critical aspect of software is its architectural design. By guaranteeing a correct architectural design, major and costly flaws can be caught early on in the development cycle. Software architecture design has received a lot of attention in the past years, with several methods, techniques and tools developed. However, there is still more to be done, such as providing adequate formal analysis of software architectures. On these regards, a framework to ensure system dependability from design to implementation has been developed at FIU (Florida International University). This framework is based on SAM (Software Architecture Model), an ADL (Architecture Description Language), that allows hierarchical compositions of components and connectors, defines an architectural modeling language for the behavior of components and connectors, and provides a specification language for the behavioral properties. The behavioral model of a SAM model is expressed in the form of Petri nets and the properties in first order linear temporal logic. This dissertation presents a formal verification and testing approach to guarantee the correctness of Software Architectures. The Software Architectures studied are expressed in SAM. For the formal verification approach, the technique applied was model checking and the model checker of choice was Spin. As part of the approach, a SAM model is formally translated to a model in the input language of Spin and verified for its correctness with respect to temporal properties. In terms of testing, a testing approach for SAM architectures was defined which includes the evaluation of test cases based on Petri net testing theory to be used in the testing process at the design level. Additionally, the information at the design level is used to derive test cases for the implementation level. Finally, a modeling and analysis tool (SAM tool) was implemented to help support the design and analysis of SAM models. The results show the applicability of the approach to testing and verification of SAM models with the aid of the SAM tool.

Development and testing of a safety module for diagnostics and protection from hazards in secondary woodworking machinery

The main theme covered by this dissertation is safety, set in the context of automatic machinery for secondary woodworking. The thesis describes in detail the project of a software module for CNC machining centers to protect the operator against hazards and to report errors in the machine safety management. Its design has been developed during an internship at SCM Group technical department. The development of the safety module is addressed step by step in a detailed way: first the company and the reference framework are introduced and then all the design choices are explained and justified. The discussion begins with a detailed analysis of the standards concerning woodworking machines and safety-related software. In this way, a clear and linear procedure can be established to develop and implement the internal structure of the module, its interface, and its application to specific safety-critical conditions. Afterwards, particular attention is paid to software testing, with the development of a comprehensive test procedure for the module, and to diagnostics, especially oriented towards signal management in IoT mode. Finally, the safety module is used as an anti-regression tool to initiate a design improvement of the machine control program. The refactoring steps performed in the process are explained in detail and the SCENT approach is introduced to test the result.

Estimating HIV-1 incidence using the serologic testing algorithm for recent HIV infections at HIV counseling and testing centers in the city of São Paulo, Brazil

The network of HIV counseling and testing centers in São Paulo, Brazil is a major source of data used to build epidemiological profiles of the client population. We examined HIV-1 incidence from November 2000 to April 2001, comparing epidemiological and socio-behavioral data of recently-infected individuals with those with long-standing infection. A less sensitive ELISA was employed to identify recent infection. The overall incidence of HIV-1 infection was 0.53/100/year (95% CI: 0.31-0.85/100/year): 0.77/100/year for males (95% CI: 0.42-1.27/100/year) and 0.22/100/ year (95% CI: 0.05-0.59/100/year) for females. Overall HIV-1 prevalence was 3.2% (95% CI: 2.8-3.7%), being 4.0% among males (95% CI: 3.3-4.7%) and 2.1% among females (95% CI: 1.6-2.8%). Recent infections accounted for 15% of the total (95% CI: 10.2-20.8%). Recent infection correlated with being younger and male (p = 0.019). Therefore, recent infection was more common among younger males and older females.