Continuous polyacrylonitrile nanofiber yarns: Preparation and dry-drawing treatment for carbon nanofiber production

Precursor fibers with diameters in nanometer scale and highly aligned polymer chains in fibers are highly promising for the preparation of high-performance carbon nanofibers, but are challenging to make. In this study, we demonstrate for the first time that a carbon nanofiber precursor can be prepared by the electrospinning of polyacrylonitrile into a nanofiber yarn and by the subsequent drawing treatment of the yarn in dry conditions. The yarn shows excellent drawing performance, which can be drawn evenly up to 6 times of its original length without breaking. The drawing treatment improves the yarn and fiber uniformity, polymer chain orientation within the fibers, as well as yarn tension and modules, but shows decreased yarn and fiber diameter and elongation at break. The drawing temperature and force show influences on the drawing behavior. The highest strength and modules (362 ± 37 MPa and 9.2 ± 1.4 GPa, respectively) are found on the yarn drawn by 5 times its length, which increased by 800% and 1800% when compared to the as-spun yarn. Through un-optimized stabilization and carbonization treatments, we further demonstrate that the carbonized nanofiber yarn shows comparable tensile properties as the commercial carbon fibers. Electrospun nanofiber yarns may form next generation precursors for making high performance carbon fibers. This journal is

Electrospinning of nanofibre yarns using rotating ring collector

 In this project, a novel ring collector was used to convert newly electrospun nanofibres into yarn. This setup has been designed to separate electrospinning from yarn drafting/twisting in two distinct zones. Three different types of electrospinning systems, i.e. needle, needleless, and needle/needleless hybrid, were utilized to produce nanofibre yarns.

The influence of fiber diameter, fabric attributes and environmental conditions on wetness sensations of next-to-skin knitwear

This study investigated the relationships between the sensations of sweaty, damp, muggy and clingy, as assessed by human response from wearer trial garment assessment, and fiber type, fiber, yarn and fabric properties and instrumental fabric measurements of next-to-skin knitwear. Wearer trial assessment of 48 fabrics followed a strict 60 minute protocol including a range of environmental conditions and levels of exercise. Adjusted mean weighted scores were determined using linked garments. Instrumental fabric handle measurements were determined with the Wool HandleMeter (WHM) and Wool ComfortMeter. Data were analyzed using forward stepwise general linear modeling. Mean fiber diameter (MFD) affected the sweaty, damp, muggy and clingy sensation responses accounting for between 23.5% and 56.2% of the variance of these sensations. In all cases, finer fibers were associated with lower sensation scores (preferred). There were also effects of fiber type upon sweaty, muggy and clingy scores, with polyester fiber fabrics having higher scores (less preferred) compared with fabrics composed of wool, particularly for peak sweaty scores in hot and active environments. Attributes such as fabric density, yarn linear density, knitting structure and finishing treatments, but not fabric thickness, accounted for some further variance in these attributes once MFD had been taken into account. This is explained as finer fibers have a greater surface area for any given mass of fiber and so finer fibers can act as a more effective sink for moisture compared with coarser fibers. No fabric handle parameter or other attribute of fiber diameter distribution was significant in affecting these sensation scores.

Fabric handle properties of superfine wool fabrics with different fibre curvature, cashmere content and knitting tightness

The handle properties of single jersey fabrics composed of superfine wools (17 μm) of different fibre curvature (114 vs. 74 °/mm) in blends with cashmere (fibre curvature 49 °/mm) were investigated. There were four blend ratios of cashmere (0, 25, 50, 75%) plus 100% cashmere. Each of the nine fibre blend combinations were replicated three times, and each was knitted into three tightness factors. The 81 fabrics were evaluated using the Wool HandleMeter, which measures seven primary handle attributes and Overall handle, and have been calibrated using a panel of experts and a wide variety of commercial fabrics. Results were analysed by ANOVA and general linear modelling. Tightness factor significantly affected all Wool HandleMeter attribute values, with the effect of tightness factor varying according to handle attribute. The Wool HandleMeter was able to detect differences between fabrics composed of superfine wool differing in fibre curvature, with lower fibre curvature wool fabrics having more preferred Overall handle and softer, looser, cooler, lighter and less dry handle attributes at some or all tightness factors compared with fabrics composed of higher fibre curvature superfine wool. Progressively blending cashmere with wool significantly improved Overall handle, increased soft and smooth handle, reduced dry, heavy and tight handle. Linear regression modelling indicated that fabric mass per unit area explained more than 50% of the variance in overall fabric handle and in combination with variations in fabric thickness and yarn elongation could explain 71% of the variance in Overall handle.

Effects of fibre parameters on the ultraviolet protection of fibre assemblies

Ultraviolet (UV) radiation protection is becoming increasingly necessary for human health, and textiles play an important role. The interaction between UV light and textiles is a complex one, involving fibre, yarn and fabric parameters. In this study, an optical model is presented for examining the influences of fibre parameters on the UV protection offered by a bundle of fibres with a given mass. The effects of mean fibre diameter and fibre type on UV absorption were examined. The model was verified with results of UV–visible diffuse reflectance measurements on natural and synthetic fibres. When the mass of fibres was kept constant, within the measurement range in this study, a bundle of fibres with coarser fibres had a lower UV reflectance than that with finer ones. The model accurately predicted factors influencing UV protection, including fibre diameter, fibre transmittance, porosity and refractive index.

Direct electrospinning of nanofibre yarns using a rotating ring collector

Nanofibres prepared by electrospinning typically have randomly oriented fibrous structure. They have large surface-to-volume (or weight) ratio and excellent porous characteristic, which have shown enormous potential in diverse applications. However, electrospun nanofibres are often prepared in the form of randomly orientated fibrous web, which are fragile and difficult to be tailored in fibrous structures. Herein, we demonstrate a novel yarn electrospinning method which uses a rotating ring collector to convert newly electrospun nanofibres directly into a continuous yarn. The use of ring collector separates the yarn formation from the electrospinning zone. The deposition of later-spun nanofibres to the inner surface of fibrous cone eliminates hooked or curled nanofibres in the final yarn. The effects of polymer concentration and operating parameters on nanofibre and yarn morphology, diameter and the ring collector on yarn twist feature were examined. The nanofibre yarns had a surface twist angle up to 54.4°, and tensile strength as high as 93.6 MPa (elongation at break 242.6%). Increasing twist levels improves tensile strength and strain values.

UV protection performance of textiles affected by fiber cross-sectional shape

Abstract
In this study, a model was set up for simulating the effects of varying fiber cross-sectional shapes on ultraviolet protection of fibers. The fiber diameter and fiber type were also involved in the model setting. Experiments of diffuse reflectance spectra measurement on natural (wool, cotton, silk), regenerated (bamboo viscose) and synthetic (polyester, nylon) fibers were conducted to verify the model predicted results. When a more complex shape was assumed as the fiber cross-section for model calculation, the predicted results have a better agreement with the actual results. The effects on ultraviolet absorption from fibers with different cross-sectional shapes were investigated at a single fiber, fiber bundle and yarn levels. With the same material, when the fiber cross-sectional area and the areal coverage of a single fiber were constant, the triangular shape had the lowest ultraviolet transmittance and the highest ultraviolet reflectance for a single fiber and also for a fiber bundle. The difference of fiber cross-sectional shapes was also significant in the ultraviolet protection of a single yarn.

Highly-twisted, continuous nanofibre yarns prepared by a hybrid needle-needleless electrospinning technique

Nanofibres prepared by electrospinning have shown enormous potential for various applications. They are obtained predominantly in the form of nonwoven fibre webs. The 2-dimensional nonwoven feature and fragility have considerably confined their further processing into fabrics through knitting or weaving. Nanofibre yarns, which are nanofibre bundles with continuous length and a twist feature, show improved tensile strength, offering opportunities for making 3-dimensional fibrous materials with precisely controlled fibrous architecture, porous features and fabric dimensions. Despite a few techniques having been developed for electrospinning nanofibre yarns, they are chiefly based on the needle electrospinning technique, which often has low nanofibre productivity. In this study, we for the first time report a nanofibre yarn electrospinning technique which combines both needle and needleless electrospinning. A rotating intermediate ring collector was employed to directly collect freshly-electrospun nanofibres into a fibrous cone, which was further drawn and twisted into a nanofibre yarn. This novel system was able to produce high tenacity yarn (tensile strength 128.9 MPa and max strain 222.1%) at a production rate of 240 m h^-1, with a twist level up to 4700 twists per metre. The effects of various parameters, e.g. position of the electrospinning units, operating conditions and polymer concentration, on nanofibre and yarn production were examined.

Knitted strain sensor textiles of highly conductive all-polymeric fibers

A scaled-up fiber wet-spinning production of electrically conductive and highly stretchable PU/PEDOT:PSS fibers is demonstrated for the first time. The PU/PEDOT:PSS fibers possess the mechanical properties appropriate for knitting various textile structures. The knitted textiles exhibit strain sensing properties that were dependent upon the number of PU/PEDOT:PSS fibers used in knitting. The knitted textiles show sensitivity (as measured by the gauge factor) that increases with the number of PU/PEDOT:PSS fibers deployed. A highly stable sensor response was observed when four PU/PEDOT:PSS fibers were co-knitted with a commercial Spandex yarn. The knitted textile sensor can distinguish different magnitudes of applied strain with cyclically repeatable sensor responses at applied strains of up to 160%. When used in conjunction with a commercial wireless transmitter, the knitted textile responded well to the magnitude of bending deformations, demonstrating potential for remote strain sensing applications. The feasibility of an all-polymeric knitted textile wearable strain sensor was demonstrated in a knee sleeve prototype with application in personal training and rehabilitation following injury.

O projeto politico pedagógico de enfermagem e o sistema único de saúde: a visão de discentes

This research aims to analyze, in the view of students, the pedagogic project of undergraduate nursing course, of UFRN, and its articulation with the SUS, in an attempt to understand the issues that permeate the teaching and learning of nursing. This is a qualitative study that used the focus group technique as a tool to collect empirical data. There were three meetings, where we had the collaboration of 23 graduating students from the eighth period of the semester 2009.1. For the analysis of information, we use a theoretical framework based on curriculum guidelines and basic principles of the SUS, making the analogy of the results with the metaphor of Greek mythology, Ariadne's thread, in dialogue with authors who discuss education as a transformative practice. Thus, the texture of the yarn was built of five thematic fields: joint the pedagogic project with the SUS; the teaching/service and theory/practice relation; interdisciplinarity or transdisciplinarity; didactic/methodological and relational approaches; and co-participation of students in the pedagogic project. According to the discussions, we find many difficulties in the teaching and learning process of undergraduate nursing in UFRN to strengthen the SUS, including: dislocation of educational institutions with services, professionals, managers and community; dichotomy between theory and practice; reality of services as a learning field and working process in health; posture adopted by professionals, teachers and other subjects included in the process of health education; decontextualization and fragmentation of teaching with the practice in health and nursing; excessive use of very illustrative methodologies, but little problem-solving; difficult and precarious situation in the relations between teachers and between teachers/students, regarding the acceptance of differences; absence of participation of students in the evaluation process and conduct of the educational project in progress. In this sense, we understand the need an auto-reflexive act of teaching and conducting collective pedagogical course with a view to achieving the SUS. Thus, it is necessary to support practices motivated by the polyphonic dialogue and the exercise of symbiosis and autopoiesis of subjects/actors jointly responsible for the ongoing process of learning for life.

Análise tribológica das malhas multifuncionais obtidas por multicamadas

The present work consists in the analysis of tribologycal properties of basic and multifunctional knitted fabrics. This knowledge has fundamental importance for the textile industry since it can quantify, in an objective way, the tactil. The fabrics used were characterized by friction and mechanical tests for determining the viscoelastic region, wear resistance and friction coefficient of the fabrics used. The stress-strain curve was obtained by the method Kawabata, KES-FB1. Wear tests performed with the aid of equipment Martindale. The measurement of friction coefficient, two methods were used and analyzed comparatively. The first was a method already established worldwide known as KES-FB4 and the second was an innovative method called FRICTORQ, developed by the University of Minho. These two methods were compared taking into account the relative motion between the tribologycal pairs are different from each method. While the first motion is translational, the second is rotational. It was formal that the knitted had a multifunctional fabrics tribologycal performance which was better than the basic knitted fabrics, as the viscoelastic region, was laager highlighting a multifunctional structure, with greater wear resistance mainly on the back side of the knitted fabrics and lower friction coefficient. Performing a comparative analysis between two methods used to measure the friction coefficient, it was formal that both methods were consistent in terms of results. In operational terms, the FRICTORQ showed ease of operation and increased reproducibility of results

Variação de temperatura e umidade e suas influências nas características físicas e mecânicas dos fios de algodão

Cotton is a hydrofilic textile fiber and, for this reason, it changes its properties according to the environment changes. Moisture and Temperature are the two most important factors that lead a cotton Spinning sector and influence its quality. Those two properties can change the entire Spinning process. Understanding this, moisture and temperature must be kept under control when used during the Spinning process, once the environment is hot and dry, the cotton yarns absorb moisture and lose the minimal consistency. According to this information, this paper was developed testing four types of cotton yarns, one kind of cotton from Brazil and the others from Egypt. The yarns were exposed to different temperatures and moisture in five different tests and in each test, six samples that were examined through physical and mechanical tests: resistance, strength, tenacity, yarn´s hairness, yarn´s evenness and yarn´s twisting. All the analysis were accomplished at Laboratório de Mecânica dos Fluídos and at COATS Corrente S.A., where, it was possible to use the equipments whose were fundamental to develop this paper, such as the STATIMAT ME that measures strength, tenacity, Zweigler G566, that measure hairiness in the yarn, a skein machine and a twisting machine. The analysis revealed alterations in the yarn´s characteristics in a direct way, for example, as moisture and temperature were increased, the yarn´s strength, tenacity and hairness were increased as well. Having the results of all analysis, it is possible to say that a relatively low temperature and a high humidity, cotton yarns have the best performance

Evaluation of stitched fabric composite processed by RTM in quasi-static test

Stitched fabrics have been widely studied for potential application in aircraft structures since stitch yarns offer improvements in the out-of-plane mechanical properties and also can save time in the lay up process. The down side of stitch yarns came up in the manufacturing process of fabric in which defects introduced by the needle movement creating fiber-free-zones, fiber breakage and misalignment of fibers. The dry stitched carbon fabric preform has mainly been used in the Resin Transfer Molding (RTM) process which high fiber content is aimed, those defects influence negatively the injection behavior reducing the mechanical properties of final material. The purpose of this research work focused on testing in quasi-static mechanical mode (in-plane tension) of a monocomponent resin CYCOM (R) 890 RTM/carbon fiber anti-symmetric quadriaxial fabric stitched by PE 80Dtex yarn processed by RTM. The evaluation consisted in comparing the scatter of the quasi-static test with the attenuation of ultrasonic maps, which show the path of the resin and possible dry spots considering that interference of yarn in resin flow is detectable in ultrasonic measurement. Microscopic analysis was also considered for further evaluation in case of premature failure. (C) 2011 Published by Elsevier Ltd. Selection and peer-review under responsibility of ICM11

Hypertension favors the inflammatory process in rats with experimentally induced periodontitis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Movimento de gaveta em joelhos de cães submetidos à estabilização extracapsular após secção do ligamento cruzado cranial in vitro

A técnica TightRope, que procura aperfeiçoar a estabilização extra-capsular com sutura lateral, por meio da realização de mínimas incisões e criação de túneis ósseos em pontos isométricos, que permitem a inserção de mecanismo que anula o movimento de gaveta, além de reduzir a ocorrência de complicações graves. Dessa forma, objetivou-se avaliar a modificação da técnica TightRope em joelhos de cadáveres caninos com a finalidade de disponibilizar um procedimento simples e de custo reduzido para tratamento da Ruptura do ligamento cruzado cranial (RLCCr). Experimentalmente, foram utilizados 20 membros pélvicos de dez cadáveres caninos, provenientes do setor de patologia da Universidade Norte do Paraná, os quais pesavam entre 6,3 e 24kg. Para estabilização do LCCr, rompido intencionalmente, foi adotada a técnica de TightRope modificada utilizando fio de poliamida, cavilha e emprego de um parafuso ortopédico para proporcionar a fixação óssea. Comparando os valores de deslocamento obtidos durante a realização do movimento de gaveta previamente à ruptura do LCCr e após a realização do procedimento cirúrgico, observou-se que a modificação da técnica TightRope promoveu estabilidade significativa para a maioria (12 de 20) dos joelhos testados (P=0,0033). Contudo, essa estabilidade foi inferior, quando comparada à estabilidade do ligamento intacto.