Soil water evaporation under densities of coverage with vegetable residue

This study was conducted at the Agronomic Institute of Paraná (IAPAR) in Londrina, State of Paraná (PR), Brazil (latitude 23º18'S, longitude 51º09'W and average altitude of 585 m). The local climate, according to the classification of Köeppen, is Cfa type, i.e., humid subtropical climate, with rain in all seasons and can occur dry seasons during the winter. It was determined soil evaporation (E) under different coverage densities with residue from the wheat crop. The treatments were installed in weighting lysimeters of 2.66 m² and 1.3 m deep, which allows to determine E by the mass difference with measuring precision of 0.1mm at one hour intervals. Treatments consisted of 0; 2.5; 5 and 10 t ha-1 of wheat crop residues, placed evenly over each lysimeter. In the first cycle (September 22nd to October 20th, 2008), the reduction of E, as compared to a bare soil, was 4; 15 and 24%, while in the second cycle (December 1st to 30th, 2008), the reduction was of 15; 22 and 25%, respectively, for the treatments of 2.5; 5 and 10 t ha-1.

Energetic analysis of landrace varieties and hybrids of corn produced in different technological levels of management

The aim of this study was to analyze, under the energetic point of view, the cultivation of corn in three management systems (low, medium and high-tech), using two landrace varieties ('Argentino' and 'BR da Várzea'), a double hybrid cultivar (SHS 4080) and a simple hybrid (IAC 8333). Five performance indicators were used: energy efficiency, liquid cultural energy, cultural efficiency, energy balance and productive energy efficiency. From the perspective of family farming, it was verified the largest social importance of the systems under low and medium levels of technology, due to the increase employment capacity of rural labor. The liquid cultural energy and energy balance were more favorable for the system under high technological level, unlike cultural efficiency and productive energy efficiency, which were significantly higher for medium and low technological levels. The variety 'Argentino' showed lower productive energy efficiency. The variety 'BR da Várzea', on the other hand, presented the potential to generate energy as much as the hybrids. In general, the biggest sustainability in the corn crop was achieved when the management system under medium and lower levels of technology were used.

Technological development of 40mg furosemide tablets: equivalence and bioavaibility study in dogs

Furosemide (40mg) was administered to 20 street dogs, 10 males and 10 females, in two different pharmaceutical forms: (1) compressed furosemide 40mg formulated at the Federal University of Pernambuco (UFPE-tablet), and (2) a commercial formulation with equal bioequivalence produced by the Laboratory for Pharmaceutical Technology of Pernambuco State (LAFEPE), the LAFEPE-furosemide. The study aimed to evaluate the kinetics of dissolution of the UFPE-tablet in order to analyze the behavior of bioavailability of the best formulation for veterinary use. The plasmatic concentrations of furosemide for the determination of parameters of pharmacological kinetics were analyzed by high-performance liquid chromatographic method (HPLC). The in vitro study accomplished through physiochemical analyses demonstrated that the formulas of the furosemide tablets attained the pharmaceutical requirements in agreement with USP 23 and the Brazilian Pharmacopoeia. The evaluation accomplished in dogs with UFPE-tablets given in only dose demonstrated uniformity in blood levels indicating stability in maintenance of the pharmaceutical formulation and efficiency in absorption of the active compound. These values are not significantly different in relation to the 5% confidence limit. Regarding maximum concentration (Tmax) time and global bioavaibility assessed by AUC means, there were no considerable differences as well. UFPE-furosemide displayed 743.492µg/mL.h as AUC average value whereas LAFEPE-furosemide had an average of 537.284µg/mL.h.

Technological level and epidemiological aspects of sheep husbandry in Minas Gerais, southeastern Brazil

Epidemiological and health aspects of sheep husbandry were assessed on 213 sheep flocks in 142 municipalities from the state of Minas Gerais, southeastern Brazil. An updated questionnaire was filled out for each flock, requesting data on the farm, the flock and the farmer by the veterinarians of the State Government Agency for Animal Health (Instituto Mineiro de Agropecuária). Thirteen important variables were selected and scored to determine the technological level of the 117 farms; 0.9% of them was classified as high technological level, 45.3% as medium technological level and 53.0% as low technological level. Lamb production was the main objective of the farms and the main features were low-frequencies of individual identification of animals (16.9%), technical assistance (31.9%), use of quarantine for newly acquired animals (0.9%) the separation of animals by age group (3.7%) and requeste the sanitary certificate at purchasing of animals (11.7%). The main health problems reported were abortion (23.9%), keratoconjunctivitis (17.9%), contagious ecthyma (13.6%), pneumonia (10.3%), diarrhea (9.3%) and caseous lymphadenitis (6.1%). Information of the epidemiological situation and the mainly health measures used in the sheep farms are important to improve the productivity and quality of the lamb.

Weeds infestation in corn intercropped with forages at different planting densities

Corn is planted in the Center West region of Brazil as a second crop, following soybeans or beans. Intercropping of Brachiaria species with corn as a second crop increases the mulching in the cropping system. This study aimed to evaluate the weeds infestation in soybeans following corn/forages intercrop, as a function of corn plant structure, forage species and density. Experiments were conducted in a completely randomized blocks design with four replications, in Ponta Porã and Dourados municipalities, Mato Grosso do Sul state, Brazil, in 2010/2011. Treatments consisted of three corn hybrids with distinct plant architectures intercropped with three forage species: Brachiaria ruziziensis, B. brizantha and B.decumbens, at five densities, and the resulting dry mass was maintained throughout the winter. During the following cropping season, forages were desiccated prior to planting soybeans, and the dry mass of weeds, dry mass of the mulching, soil coverage by weeds, and the broadleaf/grass weed species index (WPI) were determined 15 days after soybean emergence, submitted to an F-test, and analyzed either by regression or by multiple mean comparison, according to the nature of the data. When intercropping corn with species of Brachiaria, a reduction in the overall weeds infestation may always be expected; among the studied forage species, more problems with weeds may be anticipated in areas with a less competitive species, e.g. B.ruziziensis. Under the conditions of the trials, B.brizantha and B.decumbens were more capable of inhibiting the emergence of weed species in the winter.

Variations in weed population densities, rate of change and community diversity in RR-soybeans and RR-maize strip crops under two herbicide strategies

Concerns about the sustainability of large-scale, direct-drilled RR-soybeans (Glycine max), and RR-maize (Zea mays) under monoculture in central Argentina are growing steadily. An experiment was conducted during three consecutive years to determine the effects of crops and systems (monocultures and strips) and herbicide strategy on weed density, population rate of change (l), b community diversity (H´), crop yields and Land Equivalent Ratio (LER). Not only crops but also crop systems differentially influenced weed densities along their growth and development. For crop harvests, weed densities increased in both maize crop systems as compared to in the one for soybeans, but the lowest increase occurred in soybean strips. Differences were leveled by both herbicide strategies, which achieved 73% efficacy during the critical periods in both crops. l of annual monocotyledonous increased, thus shifting the weed community composition. Species richness and H´ were not affected by crop systems, but both herbicide strategies, particularly POST, either in soybeans in monoculture or in maize strips, significantly enhanced H´. Crop yields significantly increased in the maize-strip system with POST (Year 1) or PRE (Years 2 and 3) strategies, thus increasing LER above 1. Herbicide Environmental Load treatments fall within very low or low field use rating.

Weeds under the canopies of tree species submitted to different planting densities and intercropping

Assessing the growth and floristic composition of species that grow under the canopy of trees is important for weed control (WC). The objective of this study was to assess two experiments (E1 and E2), when the trees were two years and one year of age, respectively. In E1, sabiá (S) and gliricidia (G) were submitted to planting densities from 400 to 1.200 plants ha-1. In E2, growing systems consisting of S, G, and neem (N) combinations were compared: SSS, GGG, NNN, GSG, NSN, SGS, NGN, SNS, and GNG (each letter represents a row of plants). A random block design was adopted, with three (E1) and four (E2) replicates. In E1, treatments were arranged as split-plots (species in plots). In E2, the degrees of freedom for treatments (8) were partitioned into growing systems (treatments that involved the same species) and between growing system groups (2). Twenty-one weed species were found in E1. Gliricidia attained greater plant height than sabiá, but these species did not differ in canopy diameter, number of weed species per plot, and weed green and dry biomass of the shoot. Higher planting densities resulted in the reduction of all those traits. Twenty-six weed species were found in E2. Growing systems that included gliricidia showed canopies with greater diameters than growing systems that included neem. There were no differences between growing systems for number of weed species per plot and for weed green and dry biomass of the shoot.

Sourgrass densities affecting the initial growth and macronutrient content of coffee plants

The objective of this work was to evaluate the coexistence effects of coffee (Coffea arabica) with densities of sourgrass (Digitaria insularis) on crop macronutrient content and plant growth. The experiment was conducted in plots where one coffee plant was maintained in coexistence with 0 (weed-free check), 1, 2, 4, 8, and 16 sourgrass plants, using a completely randomized design with three replicates. Reduction of coffee growth and macronutrient content, except P that increased, started when the coexistence occurred with sourgrass plants in a density of 1 plant per plot. In general, macronutrient content was reduced by 18-50%, while growth characteristics were reduced by 9-41%, when coffee plants coexisted with 16 plants of sourgrass. Thus, sourgrass competition for nutrients was a strong factor limiting coffee plant growth.

Anatomy and physiology of Cattail as related to different population densities

The objective of this work was to evaluate the effects of the population density of Typha angustifolia plants in the anatomical and physiological characteristics. Plants were collected from populations of high density (over 50% of colonization capacity) and low density (less than 50% of colonization capacity) and cultivated under controlled greenhouse conditions. Plants from both populations were grown in plastic trays containing 4 L of nutritive solution for 60 days. At the end of this period, the relative growth rate, leaf area ratio, net assimilatory rate, root/shoot ratio, leaf anatomy, root anatomy, and catalase and ascorbate peroxidase activities were evaluated. Plants from high density populations showed increased growth rate and root/shoot ratio. Low density populations showed higher values of stomatal index and density in leaves, as well as increased palisade parenchyma thickness. Root epidermis and exodermis thickness as well as the aerenchyma proportion of high density populations were reduced, these plants also showed increased vascular cylinder proportion. Only catalase activity was modified between the high and low density populations, showing increased values in low density populations. Therefore, different Typha angustifolia plants show differences in its anatomy and physiology related to its origins on high and low density conditions. High density population plants shows increased growth capacity related to lower apoplastic barriers in root and this may be related to increased nutrient uptake capacity.

Lightweight, liquid-cooled, direct-drive generator for highpower wind turbines: motivation, concept, and performance

Thesis: A liquid-cooled, direct-drive, permanent-magnet, synchronous generator with helical, double-layer, non-overlapping windings formed from a copper conductor with a coaxial internal coolant conduit offers an excellent combination of attributes to reliably provide economic wind power for the coming generation of wind turbines with power ratings between 5 and 20MW. A generator based on the liquid-cooled architecture proposed here will be reliable and cost effective. Its smaller size and mass will reduce build, transport, and installation costs. Summary: Converting wind energy into electricity and transmitting it to an electrical power grid to supply consumers is a relatively new and rapidly developing method of electricity generation. In the most recent decade, the increase in wind energy’s share of overall energy production has been remarkable. Thousands of land-based and offshore wind turbines have been commissioned around the globe, and thousands more are being planned. The technologies have evolved rapidly and are continuing to evolve, and wind turbine sizes and power ratings are continually increasing. Many of the newer wind turbine designs feature drivetrains based on Direct-Drive, Permanent-Magnet, Synchronous Generators (DD-PMSGs). Being low-speed high-torque machines, the diameters of air-cooled DD-PMSGs become very large to generate higher levels of power. The largest direct-drive wind turbine generator in operation today, rated just below 8MW, is 12m in diameter and approximately 220 tonne. To generate higher powers, traditional DD-PMSGs would need to become extraordinarily large. A 15MW air-cooled direct-drive generator would be of colossal size and tremendous mass and no longer economically viable. One alternative to increasing diameter is instead to increase torque density. In a permanent magnet machine, this is best done by increasing the linear current density of the stator windings. However, greater linear current density results in more Joule heating, and the additional heat cannot be removed practically using a traditional air-cooling approach. Direct liquid cooling is more effective, and when applied directly to the stator windings, higher linear current densities can be sustained leading to substantial increases in torque density. The higher torque density, in turn, makes possible significant reductions in DD-PMSG size. Over the past five years, a multidisciplinary team of researchers has applied a holistic approach to explore the application of liquid cooling to permanent-magnet wind turbine generator design. The approach has considered wind energy markets and the economics of wind power, system reliability, electromagnetic behaviors and design, thermal design and performance, mechanical architecture and behaviors, and the performance modeling of installed wind turbines. This dissertation is based on seven publications that chronicle the work. The primary outcomes are the proposal of a novel generator architecture, a multidisciplinary set of analyses to predict the behaviors, and experimentation to demonstrate some of the key principles and validate the analyses. The proposed generator concept is a direct-drive, surface-magnet, synchronous generator with fractional-slot, duplex-helical, double-layer, non-overlapping windings formed from a copper conductor with a coaxial internal coolant conduit to accommodate liquid coolant flow. The novel liquid-cooling architecture is referred to as LC DD-PMSG. The first of the seven publications summarized in this dissertation discusses the technological and economic benefits and limitations of DD-PMSGs as applied to wind energy. The second publication addresses the long-term reliability of the proposed LC DD-PMSG design. Publication 3 examines the machine’s electromagnetic design, and Publication 4 introduces an optimization tool developed to quickly define basic machine parameters. The static and harmonic behaviors of the stator and rotor wheel structures are the subject of Publication 5. And finally, Publications 6 and 7 examine steady-state and transient thermal behaviors. There have been a number of ancillary concrete outcomes associated with the work including the following. X Intellectual Property (IP) for direct liquid cooling of stator windings via an embedded coaxial coolant conduit, IP for a lightweight wheel structure for lowspeed, high-torque electrical machinery, and IP for numerous other details of the LC DD-PMSG design X Analytical demonstrations of the equivalent reliability of the LC DD-PMSG; validated electromagnetic, thermal, structural, and dynamic prediction models; and an analytical demonstration of the superior partial load efficiency and annual energy output of an LC DD-PMSG design X A set of LC DD-PMSG design guidelines and an analytical tool to establish optimal geometries quickly and early on X Proposed 8 MW LC DD-PMSG concepts for both inner and outer rotor configurations Furthermore, three technologies introduced could be relevant across a broader spectrum of applications. 1) The cost optimization methodology developed as part of this work could be further improved to produce a simple tool to establish base geometries for various electromagnetic machine types. 2) The layered sheet-steel element construction technology used for the LC DD-PMSG stator and rotor wheel structures has potential for a wide range of applications. And finally, 3) the direct liquid-cooling technology could be beneficial in higher speed electromotive applications such as vehicular electric drives.

Lactobacillus plantarum AJ2 isolated from naturally fermented sausage and its effects on the technological properties of Milano-type salami

L. plantarum, strain AJ2, was isolated from naturally fermented sausage manufactured in the Southern region of Brazil and inoculated in Milano-type salami. The lactic culture exhibited the ability of growing in the product, decreasing pH in the first seven days of fermentation/maturation and the residual levels of nitrite and nitrate, as well as peroxide and TBARS values. The inoculated sausage had the highest intensity for brightness and red color, but did not present a difference in chemical composition and fatty acid composition, compared to the control.

Lactobacillus plantarum strains isolated from naturally fermented sausages and their technological properties for application as starter cultures

In the present study, technological properties of L. plantarum strains isolated from naturally fermented sausages manufactured in the South region of Brazil were investigated in order to obtain a starter culture. The technological properties evaluated were the following: ability to growth at different pH values, at different temperatures, in different salt concentrations and in the presence of commercial curing salt, fast production of acid, determination of D - and L - lactic acid; nitrate reductase activity; antagonistic activity and stability of the isolated cultures after fermentation, concentration, and freeze-drying process. The isolated strains showed effectiveness to improve technological properties as starter cultures.