Preisach modeling of hysteresis for a pseudoelastic Cu-Zn-Al single crystal

Stress-strain trajectories associated with pseudoelastic behavior of a Cu¿19.4 Zn¿13.1 Al (at.%) single crystal at room temperature have been determined experimentally. For a constant cross-head speed the trajectories and the associated hysteresis behavior are perfectly reproducible; the trajectories exhibit memory properties, dependent only on the values of return points, where transformation direction is reverted. An adapted version of the Preisach model for hysteresis has been implemented to predict the observed trajectories, using a set of experimental first¿order reversal curves as input data. Explicit formulas have been derived giving all trajectories in terms of this data set, with no adjustable parameters. Comparison between experimental and calculated trajectories shows a much better agreement for descending than for ascending paths, an indication of a dissymmetry between the dissipation mechanisms operative in forward and reverse directions of martensitic transformation.

Matriconditioning integrated with gibberellic acid to hasten seed germination and improve stand establishment of pepper and tomato

Emergence and stand establishment of tomato (Lycopersicon lycopersicum (L.) (Karsten ex Farw) and pepper (Capsicum annus L.) seeds are often slow and erratic, particularly under stress conditions. Field emergence trials sometimes have not responded to priming in pepper. This study examined the combined effects of matriconditioning and gibberellin application on the germination and stand establishment of pepper and tomato seeds. Pepper and tomato seeds were conditioned with a solid carrier, Micro Cel E, in the presence of gibberellic acid (GA) for 1, 2 , 3 and 4 days at 15 and 25ºC. The results showed that, in all cases, even under stress conditions, the combination of matriconditioning with GA was effective in improving germination and emergence of pepper and tomato. The germination time was, in average, reduced by 2 to 3 days by primed seeds. Thus, matriconditioning, during which germination is suspended, provides an unique means to rapidly and efficiently digest the endosperm by GA-induced enzymes and reduce the mechanical restraints of endosperm thus providing energy to start and sustain embryo growth.

Työssä jaksaminen. Case: Lappeenrannan kaupunki

Tämän pro gradu –tutkimuksen tarkoituksena on selvittää mitkä tekijät työyhteisössä vaikuttavat työssä jaksamiseen. Tutkimus on kvalitatiivinen ja sen empiirinen aineisto on kerätty haastattelemalla työntekijöitä kolmessa Lappeenrannan kaupungin yksikössä. Työssä jaksaminen kuvaa työntekijän suhtautumista työhönsä. Jaksaminen on tärkeää niin työntekijälle, työnantajalle kuin myös yhteiskunnalle. Olennaisiksi jaksamiseen vaikuttaviksi tekijöiksi katsotaan niin työympäristö ja työolot, itse työ ja sen hallinta sekä osaaminen, työyhteisön toiminta ja sen kehittäminen kuin myös henkinen jaksaminen ja oma fyysinen sekä psyykkinen terveys. Tämän tutkimuksen mukaan työntekijät kokivat työn hyvän hallinnan ja omien vaikutusmahdollisuuksien edesauttavan jaksamista. Samoin toimivat ja läheiset suhteet lähimpiin työtovereihin auttoivat kestämään työpaineita ja stressiä.

Propelente sólido compósito polibutadiênico: I- influência do agente de ligação

In the Brazilian Complete Spacial Mission, the research of Vehicle Satellite Launcher is important. The solid propellant composite used in this vehicle is made with ammonium perchlorate, aluminiun powder and hydroxy terminated polibutadiene resin. In the propellant the bonding agent has a function to promote the interaction between solids and polimeric matrix, improving mechanical properties as stress, strain, aging characteristics and moisture embrittlement. Due its importance in propellant, bonding agent is consider as industrial secret and the literature about it is generic, without greater informations.

Obtenção e caracterização de blendas colágeno-quitosana

Biodegradable polymer blends were obtained using collagen and chitosan. Membranes of collagen and chitosan in different proportions (3:1, 1:1 and 1:3) were prepared by mixing their acetate solutions (pH 3.5) at room temperature. The blends were characterized by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), Fourier Transform infrared (FTIR) spectroscopy, specific viscosity, water absorption and stress-strain assays. The results showed that chitosan did not interfere in the structural arrangement of the collagen triple helix and the properties of the blends can be controlled by varing the proportion of the collagen and the chitosan.

Modelo de comportamiento en sevicio para estructuras reticulares de hormigón. Parte I: Descripción del modelo y ejemplos de aplicación

A general method for instantaneous and time-dependent serviceability analysis of plane concrete frames is presented. The methodology is based in an extension of the classic matrix formulation for bars. The main aspects influencing the behaviour of the structural concrete are considered: cracking, creep, shrinkage or prestress losses. To simulate the effect of cracking a smeared model (developed in Part II) based on the modification of the tensile branch of the concrete stress-strain relationship is adopted. The general approach considered permits the application to different materials and constitutive laws. Sequential construction (sectional and structural), incorporation of reinforcement, consideration of the loads history; placing and removing shores, and restraining or releasing in boundary conditions are considered. Some examples are included to highlight the capabilities of the model

Sintesis de poliuretanos a partir de polioles obtenidos a partir del aceite de higuerilla modificado por transesterificación con pentaeritritol

Castor oil was reacted by transesterification with various percentages in mass of pentaerythritol to obtain different esters of pentaerythritol. Alternatively, glycerol was also used instead of pentaerythritol for the same reaction in order to establish comparative reference products. The products of the reactions were characterized by matrix-assisted laser desorption/ionization time-of-flight mass spectroscopy in order to detect and quantify (in terms of the molecular mass and structural information) the components of the products obtained. Analysis for hydroxyl value, acid value, viscosity and specific gravity were used to complete the characterization of the polyols obtained and also of the original castor oil. The polymer characterization was accomplished by tensile stress-strain tests, Shore A hardness, thermogravimetric analysis and chemical resistance to solvents.

Poliuretanos obtenidos a partir de aceite de higuerilla modificado y poli-isocianatos de lisina: síntesis, propiedades mecánicas y térmicas y degradación in vitro

Biodegradable polyurethanes (PUR) were prepared from polyols derived from castor oil by transesterification of pentaerythritol-modified castor oil and lysine polyisocyanates (LDI and LTI). The polyurethanes obtained were characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis (TGA), and dynamic mechanical thermal analysis (DMTA). The mechanical behavior of the polyurethanes was measured by Shore A hardness and tensile testing (stress-strain curves). The biodegradable nature of the material was determined by contact angle, water absorption tests, and in vitro degradation in PBS solution. This study aims to examine the effect of the structure and functionality of diisocyanate on the mechanical properties and in vitro degradation of the material. The results were compared with homologous materials obtained from isophorone diisocyanate (IPDI) used in previous works. The objective was to evaluate candidate materials that can be potentially used in tissue engineering.

Rasitusten älykäs seuranta

Tässä diplomityössä käsitellään monikappalesysteeminä mallinnetun toimilaitteen tai mekaanisen systeemin kappaleissa vaikuttavien rasitusten, siirtymien ja jännitysten laskentamenetelmiä. Työhön sisällytettyjen menetelmien valinta on toteutettu 2000-luvulla virtuaalisuunnittelua käsittelevissä tiedelehdissä julkaistujen artikkelien pohjalta. Työn tarkoituksena on muodostaa kirjallisuuskatsaus uusien laskentamenetelmien ominaisuuksista ja metodiikasta, mitä voidaan tarvittaessa soveltaa virtuaalisuunnittelun tarpeisiin. Kaksi esiteltävistä menetelmistä on optimointimenetelmiä (RBDO ja ESL). Muissa menetelmissä käsitellään muun muassa venymien rekonstruointia ja hankauskitkasta komponentteihin kohdistuvia jännityksiä. Moving frame-menetelmässä sovelletaan kelluvan koordinaatiston periaatetta, yksi menetelmistä perustuu selkeästi osarakennetekniikkaan ja yhdessä kappaleiden joustokäyttäytymistä mallinnetaan muotofunktioiden avulla. Lisäksi on kolme soveltavaa esimerkkiä rasitusten seurannasta teollisuuskoneissa. Laskentamenetelmät ovat luonteeltaan ja sovelluskelpoisuudeltaan erilaisia. Optimointimenetelmät ovat parhaimmillaan rakenteiden jatkokehitystyössä, siinä missä muut menetelmät soveltuvat joko olemassa olevien rakenteiden mallintamiseen tai kokonaan uusien systeemien suunnittelutyökaluiksi. Tätä eroavuutta voidaan pitää hyvänä asiana, jotta voidaan valita parhaiten omiin tarkoituksiin soveltuva menetelmä.

Defining of the material models for stainless steels to be used in FE modeling

The aim of this work is to study the results of tensile tests for austenitic stainless steel type 304 and make accurate FE-models according to the results of the tests. Tensile tests were made at Central Research Institute of Structural Material, Prometey at Saint Petersburg and Mariyenburg in Russia. The test specimens for the tensile tests were produced at Lappeenranta University of Technology in a Laboratory of Steel Structures. In total 4 different tests were made, two with base material specimens and two with transverse butt weld specimens. Each kind of a specimen was tested at room temperature and at low temperature. By comparing the results of room and low temperature tests of similar test specimen we get to study the results of work hardening that affect the austenitic steels at below room temperature. The produced specimens are to be modeled accurately and then imported for nonlinear FEM- analyzing. Using the data gained from the tensile tests the aim is to get the models work like the specimens did during the tests. By using the analyzed results of the FE-models the aim is to calculate and get the stress-strain curves that correspond to the results acquired from the tensile tests.

Development of finite elements for analysis of biomechanical structures using flexible multibody formulations

The absolute nodal coordinate formulation was originally developed for the analysis of structures undergoing large rotations and deformations. This dissertation proposes several enhancements to the absolute nodal coordinate formulation based finite beam and plate elements. The main scientific contribution of this thesis relies on the development of elements based on the absolute nodal coordinate formulation that do not suffer from commonly known numerical locking phenomena. These elements can be used in the future in a number of practical applications, for example, analysis of biomechanical soft tissues. This study presents several higher-order Euler–Bernoulli beam elements, a simple method to alleviate Poisson’s and transverse shear locking in gradient deficient plate elements, and a nearly locking free gradient deficient plate element. The absolute nodal coordinate formulation based gradient deficient plate elements developed in this dissertation describe most of the common numerical locking phenomena encountered in the formulation of a continuum mechanics based description of elastic energy. Thus, with these fairly straightforwardly formulated elements that are comprised only of the position and transverse direction gradient degrees of freedom, the pathologies and remedies for the numerical locking phenomena are presented in a clear and understandable manner. The analysis of the Euler–Bernoulli beam elements developed in this study show that the choice of higher gradient degrees of freedom as nodal degrees of freedom leads to a smoother strain field. This improves the rate of convergence.

Myocardial contractility of the isovolumetrically beating isolated rat heart

Several indexes of myocardial contractility have been proposed to assess ventricular function in the isovolumetrically beating isolated heart. However, the conclusions reached on the basis of these indexes may be influenced by ventricular geometry rather than contractility itself. The objective of the present study was to assess the performance of widely used contractility indexes in the isovolumetrically beating isolated heart in two experimental models of hypertrophy, the spontaneously hypertensive rat (SHR) and infrarenal aortocava fistula. Compared to normotensive controls (N = 8), SHRs with concentric hypertrophy (N = 10) presented increased maximum rate of ventricular pressure rise (3875 ± 526 vs 2555 ± 359 mmHg/s, P < 0.05) and peak of isovolumetric pressure (187 ± 11 vs 152 ± 11 mmHg, P < 0.05), and decreased developed stress (123 ± 20 vs 152 ± 26 g/cm², P < 0.05) and slope of stress-strain relationship (4.9 ± 0.42 vs 6.6 ± 0.77 g/cm²/%). Compared with controls (N = 11), rats with volume overload-induced eccentric hypertrophy (N = 16) presented increased developed stress (157 ± 38 vs 124 ± 22 g/cm², P < 0.05) and slope of stress-strain relationship (9 ± 2 vs 7 ± 1 g/cm²/%, P < 0.05), and decreased maximum rate of ventricular pressure rise(2746 ± 382 vs 3319 ± 352 mmHg, P < 0.05) and peak of isovolumetric pressure (115 ± 14 vs 165 ± 13 mmHg/s, P < 0.05). The results suggested that indexes of myocardial contractility used in experimental studies may present opposite results in the same heart and may be influenced by ventricular geometry. We concluded that several indexes should be taken into account for proper evaluation of contractile state, in the isovolumetrically beating isolated heart.

Stresses of a boat trailer

In this thesis work, a strength analysis is made for a boat trailer. The studied trailer structure is manufactured from Ruukki’s structural steel S420. The main focus in this work is in the trailer’s frame. The investigation process consists two main stages. These stages are strain gage measurements and finite elements analysis. Strain gage measurements were performed to the current boat trailer in February 2015. Static durability and fatigue life of the trailer are analyzed with finite element analysis and with two different materials. These materials are the current trailer material Ruukki’s structural steel S420 and new option material high strength precision tube Form 800. The main target by using high strength steel in a trailer is weight reduction. The applied fatigue analysis methods are effective notch stress and structural hot spot stress approaches. The target of these strength analyses is to determine if it is reasonable to change the trailer material to high strength steel. The static strengths of the S420 and Form 800 trailers is sufficient. The fatigue strength of the Form 800 trailer is considerably lower than the fatigue strength of the S420 trailer. For future research, the effect of hot dip galvanization to the high strength steel has to be investigated. The effect of hot dip galvanization to the trailer is investigated by laboratory tests that are not included in this thesis.

Finite Element Analysis of Warship Structures

Warships are generally sleek, slender with V shaped sections and block coefficient below 0.5, compared to fuller forms and higher values for commercial ships. They normally operate in the higher Froude number regime, and the hydrodynamic design is primarily aimed at achieving higher speeds with the minimum power. Therefore the structural design and analysis methods are different from those for commercial ships. Certain design guidelines have been given in documents like Naval Engineering Standards and one of the new developments in this regard is the introduction of classification society rules for the design of warships.The marine environment imposes subjective and objective uncertainties on ship structure. The uncertainties in loads, material properties etc.,. make reliable predictions of ship structural response a difficult task. Strength, stiffness and durability criteria for warship structures can be established by investigations on elastic analysis, ultimate strength analysis and reliability analysis. For analysis of complicated warship structures, special means and valid approximations are required.Preliminary structural design of a frigate size ship has been carried out . A finite element model of the hold model, representative of the complexities in the geometric configuration has been created using the finite element software NISA. Two other models representing the geometry to a limited extent also have been created —- one with two transverse frames and the attached plating alongwith the longitudinal members and the other representing the plating and longitudinal stiffeners between two transverse frames. Linear static analysis of the three models have been carried out and each one with three different boundary conditions. The structural responses have been checked for deflections and stresses against the permissible values. The structure has been found adequate in all the cases. The stresses and deflections predicted by the frame model are comparable with those of the hold model. But no such comparison has been realized for the interstiffener plating model with the other two models.Progressive collapse analyses of the models have been conducted for the three boundary conditions, considering geometric nonlinearity and then combined geometric and material nonlinearity for the hold and the frame models. von Mises — lllyushin yield criteria with elastic-perfectly plastic stress-strain curve has been chosen. ln each case, P-Delta curves have been generated and the ultimate load causing failure (ultimate load factor) has been identified as a multiple of the design load specified by NES.Reliability analysis of the hull module under combined geometric and material nonlinearities have been conducted. The Young's Modulus and the shell thickness have been chosen as the variables. Randomly generated values have been used in the analysis. First Order Second Moment has been used to predict the reliability index and thereafter, the probability of failure. The values have been compared against standard values published in literature.

Circulation in the indian ocean in relation to the monsoon circulation of the atmosphere

The present thesis is an attempt by the researcher to Investigate the surface circulation of the Indian Ocean, north of 2095 in relation to the atmospheric circulation over the ocean. The aim is achieved by working out the circu1ation pattern and correlating it with the computed wind stress and its vorticity. The month wise surface circulation is arrived by drawing the streamlines, using freshand method with superimposed isotache. The zonal ad meridional componance of the wind stress and the curl of the wind stress are computed for each month over 2° latitude longitude quadrangle from the bulk aerodynamic formula, using a computer program. The data for drawing the surface circu1ation and for computing the wind stress and its curl have come from the Dutch Atlas.