Design of Piles for Integral Abutment Bridges, HR-252, 1984

More and more, integral abutment bridges are being used in place of the more traditional bridge designs with expansion releases. In this study, states which use integral abutment bridges were surveyed to determine their current practice in the design of these structures. To study piles in integral abutment bridges, a finite element program for the soil-pile system was developed (1) with materially and geometrically nonlinear, two and three dimensional beam elements and (2) with a nonlinear, Winkler soil model with vertical, horizontal, and pile tip springs. The model was verified by comparison to several analytical and experimental examples. A simplified design model for analyzing piles in integral abutment bridges is also presented. This model grew from previous analytical models and observations of pile behavior. The design model correctly describes the essential behavioral characteristics of the pile and conservatively predicts the vertical load-carrying capacity. Analytical examples are presented to illustrate the effects of lateral displacements on the ultimate load capacity of a pile. These examples include friction and end-bearing piles; steel, concrete, and timber piles; and bending about the weak, strong, and 45° axes for H piles. The effects of cyclic loading are shown for skewed and nonskewed bridges. The results show that the capacity of friction piles is not significantly affected by lateral displacements, but the capacity of end-bearing piles is reduced. Further results show that the longitudinal expansion of the bridge can introduce a vertical preload on the pile.

Investigation of Plastic Pipes for Highway Applications, HR-373A, Phase II, 1997

It is generally accepted that high density polyethylene pipe (HDPE) performs well under live loads with shallow cover, provided the backfill is well compacted. Although industry standards require carefully compacted backfill, poor inspection and/or faulty construction may result in soils that provide inadequate restraint at the springlines of the pipes thereby causing failure. The objectives of this study were: 1) to experimentally define a lower limit of compaction under which the pipes perform satisfactorily, 2) to quantify the increase in soil support as compaction effort increases, 3) to evaluate pipe response for loads applied near the ends of the buried pipes, 4) to determine minimum depths of cover for a variety of pipes and soil conditions by analytically expanding the experimental results through the use of the finite element program CANDE. The test procedures used here are conservative especially for low-density fills loaded to high contact stresses. The failures observed in these tests were the combined effect of soil bearing capacity at the soil surface and localized wall bending of the pipes. Under a pavement system, the pipes' performance would be expected to be considerably better. With those caveats, the following conclusions are drawn from this study. Glacial till compacted to 50% and 80% provides insufficient support; pipe failureoccurs at surface contact stresses lower than those induced by highway trucks. On the other hand, sand backfill compacted to more than 110 pcf (17.3 kN/m3) is satisfactory. The failure mode for all pipes with all backfills is localized wall bending. At moderate tire pressures, i.e. contact stresses, deflections are reduced significantly when backfill density is increased from about 50 pcf (7.9 kN/m^3) to 90 pcf (14.1 kN/m^3). Above that unit weight, little improvement in the soil-pipe system is observed. Although pipe stiffness may vary as much as 16%, analyses show that backfill density is more important than pipe stiffness in controlling both deflections at low pipe stresses and at the ultimate capacity of the soil-pipe system. The rate of increase in ultimate strength of the system increases nearly linearly with increasing backfill density. When loads equivalent to moderate tire pressures are applied near the ends of the pipes, pipe deflections are slighly higher than when loaded at the center. Except for low density glacial till, the deflections near the ends are not excessive and the pipes perform satisfactorily. For contact stresses near the upper limit of truck tire pressures and when loaded near the end, pipes fail with localized wall bending. For flowable fill backfill, the ultimate capacity of the pipes is nearly doubled and at the upper limit of highway truck tire pressures, deflections are negligible. All pipe specimens tested at ambient laboratory room temperatures satisfied AASHTO minimum pipe stiffness requirements at 5% deflection. However, nearly all specimens tested at elevated pipe surface temperatures, approximately 122°F (50°C), failed to meet these requirements. Some HDPE pipe installations may not meet AASHTO minimum pipe stiffness requirements when installed in the summer months (i.e. if pipe surface temperatures are allowed to attain temperatures similar to those tested here). Heating of any portion of the pipe circumference reduced the load carrying capacity of specimens. The minimum soil cover depths, determined from the CANOE analysis, are controlled by the 5% deflection criterion. The minimum soil cover height is 12 in. (305 mm). Pipes with the poor silt and clay backfills with less than 85% compaction require a minimum soil cover height of 24 in. (610 mm). For the sand at 80% compaction, the A36 HDPE pipe with the lowest moment of inertia requires a minimum of 24 in. (610 mm) soil cover. The C48 HDPE pipe with the largest moment of inertia and all other pipes require a 12 in. (305 mm) minimum soil cover.

Embankment Quality: Phase III, TR-401, 2002

This report describes test results from a full-scale embankment pilot study conducted in Iowa. The intent of the pilot project was to field test and refine the proposed soil classification system and construction specifications developed in Phase II of this research and to evaluate the feasibility of implementing a contractor quality control (QC) and Iowa DOT quality assurance (QA) program for earthwork grading in the future. One of the primary questions for Phase III is “Was embankment quality improved?” The project involved a “quality conscious” contractor, well-qualified and experienced Iowa Department of Transportation field personnel, a good QC consultant technician, and some of our best soils in the state. If the answer to the above question is “yes” for this project, it would unquestionably be “yes” for other projects as well. The answer is yes, the quality was improved, even for this project, as evidenced by dynamic cone penetrometer test data and the amount of disking required to reduce the moisture content to within acceptable control limits (approximately 29% of soils by volume required disking). Perhaps as important is that we know what quality we have. Increased QC/QA field testing, however, increases construction costs, as expected. The quality management-earthwork program resulted in an additional $0.03 per cubic meter, or 1.6%, of the total construction costs. Disking added about $0.04 per cubic meter, or 1.7%, to the total project costs. In our opinion this is a nominal cost increase to improve quality. It is envisioned that future contractor innovations have the potential for negating this increase. The Phase III results show that the new soil classification system and the proposed field test methods worked well during the Iowa Department of Transportation soils design phase and during the construction phase. Recommendations are provided for future implementation of the results of this study by city, county, and state agencies.

EPCM-toimitustapamallin kehittäminen Kvaerner Power Oy:n voimalaitostoimituksiin

Tämän diplomityön päämääränäoli laatia suunnitelma voimalaitoksen toimittamiseksi EPCM-toimitustavalla. Työn keskeisiksi tavoitteiksi asetettiin EPCM-toimitustapaan perustuvan toimitustapakonseptin muodostaminen, toimituksiin liittyvien terminologian selkeyttäminen ja harmonisointi sekä voimalaitoksen suhteellisen kustannusrakenteen laatiminen. Työssä tutkittiin voimalaitostoimituksissa tavanomaisesti käytettyjä sopimustyyppejä, kiinteähintaista sopimusta ja kustannusvoittolisäsopimusta sekä harvinaisemmin käytettyjä kattohinta- ja tavoitekustannussopimusta. Vallitsevat toimitustavat, EPC- ja EPCM-toimitustavat sekä monitoimittajatapa, esiteltiin ja niiden vahvuudet sekä heikkoudet selvitettiin. Projektin ominaisuuksilla, markkinoilla ja tilaajan kyvyllä, asiantuntemuksella sekä resursseilla todettiin olevan vaikutusta toimitustavan valintaan. Lisäksi tehtiin katsaus voimalaitostoimitusten kehitystrendeihin ja projektin riskienhallintaan. Voimalaitoksen laitosjärjestelmäjako kehitettiin ja sitä soveltamalla määritettiin voimalaitoksen suhteellinen kustannusrakenne. Kattilaitoksen osuus voimalaitoksen rakentamiskustannuksista todettiin merkittävimmäksi. Laitosjärjestelmien laitekustannusten havaittiin olevan korkeimmat. EPCM-toimitustapamalli kehitettiin teoriaosan pohjalta ja sen rakenne, organisaatio, sopimustyypit ja -suhteetsekä toimituksen riskien jako kuvattiin. Voimalaitoksen rakentamiskustannuksia vertailtiin eri toimitustavoilla ja EPCM-toimitustapamalli todettiin EPC-toimitustapaa edullisemmaksi.

PEC1/AtABCG32 transport function in cuticle biosynthesis

Most aerial parts of the plants are covered by a hydrophobic coating called cuticle. The cuticle is formed of cutin, a complex mixture of esterified fatty acids that are embedded and associated with waxes. The cuticle often appears as a superposition of layers of different composition: The cuticle proper formed of cutin and a mixture of waxes and underneath, the cuticle layer containing cutin, intracuticular waxes and polysaccharides of the cell wall. In addition to its involvement in plant development by preventing organ fusions, the cuticle acts as a barrier to prevent water loss and protect plants against environmental aggressions such as excessive radiation or pathogens attacks. PEC1/AtABCG32 is an ABC transporter from the PDR family involved in cutin biosynthesis. Characterization of the peci mutant in Arabidopsis thaliana showed that PEC1 plays a significant role in the diffusion barrier formation in leaves and petals. The cuticles of leaves and flowers of peci are permeable and the cuticular layer rather than the cuticular proper was altered in the petals, underlining the importance of this particular layer in the maintenance of the diffusion barrier. Chemical analysis on the flower cutin monomer composition of ped mutant revealed a decrease in hydroxylated cutin monomers, suggesting a function of PEC1 in the incorporation of these monomers in the polymer cutin. However, the exact nature of the substrates of PEC1 remained elusive. PEC1 homologues in barley and rice, respectively HvABCG31/EIBI1 and OsABCG31, are also implicated in cuticle biosynthesis. Interestingly, the rice mutant displays more severe phenotypes such as dwarfism and spreading necrosis conducting to the seedling death. In this work, we further characterized osabcg31 mutant and hairpin-RNAi downregulated OsABCG31 plant lines showing reduced growth and cuticle permeability. Our analysis showed a decrease in hydroxylated cutin monomers and severe disruptions in the cuticle, which explain the permeability. Further insights into the function of the cuticle in rice resistance/susceptibility to Pathogens were obtained after inoculation with Magnaporthe oryzae, the fungus responsible for the rice blast disease. Osabcg31 as well as the transgenic lines downregulating OsABCG31 showed increased resistance to the fungus. However, only later steps of infection are reduced . and no impact is obseived on the germination or penetration stages, suggesting that the cuticle disruption per se is not responsible for the resistance. We further investigated the cause of the resistance by analyzing the expression of defense related gene in osabcg31 prior to infection. We found that osabcg31 constitutively express defense related genes, which may explain the resistance, the dwarfism and the cell death. osabcg31 is thus a tool to study the connection between cuticle, plant development and defense signaling networks in rice. The transport function of PEC1 family members is still unknown. In order to link cutin biosynthesis and transport activity, we combined ped mutation with mutations in cutin synthesis related genes. Here, we show that PEC1 acts independently from GPAT4 and GPAT8 pathway and partially overlaps with GPAT6 biosynthesis pathway that leads to the production of hydroxylated C16 cutin precursor 2-Mono(10,16-dihydroxyhexadecanoylJglycerol (2-MHG). In addition, we noticed that despite a comparable cutin monomer composition, ped mutant leaves cuticle are permeable while that of gpat6 mutant are not. This finding raises the possibility of PEC1 being required for the incorporation of C16 hydroxylated monomers and their structural arrangement rather than their direct transport towards the cuticle. A careful investigation of the cuticle permeability, cutin composition and ultrastructure during leave development in Wt plants and ped mutants revealed a possible different regulation of several pathways of cutin biosynthesis and showed the importance of PEC1 function early during leave cuticle maturation. In order to elucidate the transport activity of PEC1, we successfully expressed PEC1 in Nicotiana benthamiana plant system for direct transport experiments. This system will be used to test the PEC 1-dependent transport of potential substrates such as sn-2-monoacylglycerol loaded with a hydroxylated C16 fatty acid. -- Toutes les parties aériennes des plantes sont recouvertes d'une couche hydrophobe appelée «cuticule». Cette cuticule est composée de cutine, un polymère d'acides gras estérifiés, et de cires. La cuticule apparaît souvent sous forme de couches superposées: une première couche extérieure appelée «cuticle proper» formée de cutine et d'un mélange de cires, et une deuxième couche, la «cuticle layer», formée de cutine associée à des cires intracuticulaires et des polysaccharides pariétaux. La cuticule joue le rôle de barrière prévenant contre la perte d'eau et les agressions environnementales. AtABCG32/PEC1 est un transporteur ABC de la famille des PDR impliqué dans la synthèse de la cutine. L'étude du mutant peci d'Arabidopsis thaliana a révélé une fonction de PEC1 dans la formation de la barrière de diffusion. La cuticule des feuilles et fleurs de peci est perméable. Des altérations de la «cuticle layer» ont été démontrées, soulignant son importance dans le maintien de la barrière. L'analyse de la composition de la cutine de peci a montré une réduction spécifique en monomères hydroxylés, suggérant un rôle de PEC1 dans leur incorporation dans la cuticule. Cependant, la nature exacte des substrats de PEC1 n'a pas été identifiée. PEC1 possède deux homologues chez l'orge et le riz, respectivement HvABCG31 et OsABCG31, et qui sont impliqués dans la biosynthèse de la cuticule. Chez le riz, des phénotypes plus sévères ont été observés tels que nanisme et nécroses conduisant à la mort des jeunes plants. Dans cette étude, nous avons continué la caractérisation de osabcg31 ainsi que des lignées de riz sous exprimant le gène OsABCG31 et présentant une cuticule perméable tout en ayant une meilleure croissance. Notre étude a démontré une réduction des monomères hydroxylés de cutine et une désorganisation de la structure de la cuticule, aggravée dans le mutant osabcg31. Ce résultat explique la perméabilité observée. Des mformations P|us approfondies sur l'implication de la cuticule dans la résistance aux pathogènes ont été obtenues après inoculation du mutant osabcg31 et les lignées sous- exprimant OsABCG31 avec une souche virulente de Magnaporthe Oryzae, le champignon responsable de la pyriculariose du riz. Les différentes lignées testées ont démontré une résistance au pathogène. Cependant, seules les étapes tardives de l'infection sont réduites et aucun impact n'est observé sur la germination des spores ou la pénétration du champignon, suggérant que les modifications de la cuticule ne sont pas directement à l'origine de la résistance. L'analyse de l'expression de gènes impliqués dans la résistance à Magnaporthe.oryzae a mis en évidence l'expression constitutive de ces gènes en l'absence de tout contact avec le pathogène. Ceci explique la résistance, le nanisme et la mort cellulaire observés. Ainsi, osabcg31 représente un outil efficace pour l'étude intégrée des systèmes de régulation de la défense, de développement des plantes et la cuticule. La nature des substrats transportés par PEC1/AtABCG32 reste inconnue. Dans le but d'établir une liaison entre biosynthèse de cutine et transport des précurseurs par PEC1, la mutation peci a été combinée avec des mutants impliqués dans différentes voies de biosynthèse. Cette étude a démontré une fonction indépendante de PEC1 de la voie de biosynthèse impliquant les enzymes GPAT4 et GPAT8, et une fonction partiellement indépendante de la voie impliquant GPAT6 qui mène à la production de précurseurs sn-2- monoacylglycerol chargés en acides gras en C16 (2-MHG). De plus, malgré un profil similaire en monomères de cutine, gpat6 conserve une cuticule imperméable alors que celle de PEC1 est perméable. Ceci suggère que PEC1 est nécessaire à l'incorporation des monomères en C16 et leur arrangement structurel plutôt que simplement à leur transport direct. L'étude approfondie de la perméabilité cuticulaire, de la structure ainsi que de la composition en cutine pendant le développement des feuilles de peci et la plante sauvage a révélé l'existence de différentes régulations des voies de biosynthèses des monomères et a démontré l'importance de PEC1 dans les premières étapes de la mise en place de la cuticule. Pour identifier les substrats transportés, l'expression de PEC1 chez le système hétérologue Nicotiana benthamiana a été conduite avec succès. Ce système sera utilisé pour tester le transport de substrats potentiels tels que le sn-2-monoacylglycerol chargé en acide gras en C16.

Severidade de doenças e manutenção da área foliar verde em função da aplicação de micronutrientes e fungicidas em trigo

Na safra agrícola de 2007 foi instalado um experimento com a cultura do trigo com o objetivo de avaliar a influência do zinco, manganês e molibdênio aplicados juntamente com fungicidas sobre a severidade de doenças e duração da área foliar verde. As aplicações dos fungicidas foram realizadas no final do emborrachamento e no florescimento, e a de micronutrientes, somente no florescimento. Foram analisados os teores de micronutrientes nas folhas, severidade das doenças causadas por Drechslera tritici-repentis eSeptoria tritici, índice SPAD (Soil Plant Analysis Development), peso hectolítrico, peso de mil grãos, tamanho de espigas, e rendimento de grãos. O uso do epoxiconazol + piraclostrobina proporcionou o melhor controle de D. tritici-repentis e de S. tritici. Produtos com epoxiconazol e piraclostrobina atuaram na fisiologia da planta, incrementando os teores de micronutrientes nos tecidos e prolongando o tempo que o trigo permaneceu com área foliar fotossinteticamente ativa. Epoxiconazol + piraclostrobina, piraclostrobina e epoxiconazol pulverizados associados ou não a micronutrientes, propiciaram aumento do peso hectolítrico, peso de mil grãos e rendimento, quando comparados à testemunha.

Sistemas de classificações geotécnicas de solos: estudo de caso aplicado à rodovia não pavimentada vcs 346, Viçosa, MG

Este artigo aborda uma contribuição às classificações geotécnicas tradicionais de solos Unified Soil Classification System (USC), Transportation Research Board System (TRB) e a Metodologia Miniatura, Compactado, Tropical (MCT) para um caso aplicado à rodovia municipal não pavimentada VCS 346, no Município de Viçosa, MG, considerando-se várias amostras deformadas de solos coletadas no subleito da referida via. Os principais objetivos deste estudo residem na contribuição de um banco de dados geotécnicos sobre classificações de solos tropicais, bem como na verificação de possíveis agrupamentos entre os sistemas geotécnicos tradicionais de classificação e a metodologia MCT. O programa de laboratório envolveu a realização dos seguintes ensaios: (i) granulometria conjunta; (ii) limites de Atterberg (LL e LP); (iii) massa específica dos grãos do solo; (iv) compactação Mini-MCV; e (v) perda de massa do corpo-de-prova por imersão em água. Os resultados possibilitaram verificar que, após a classificação das amostras, vários agrupamentos entre os sistemas de classificações geotécnicas tradicionais coincidiram com aqueles já apresentados na metodologia MCT e, considerando a pedogênese da região de Viçosa, MG, para o grupo NG', houve a contribuição dos grupos SC, SM e CL do Sistema USC e do grupo A-4 do Sistema TRB.

Regulation of Systemic Acquired Resistance through the Interaction of Arabidopsis thaliana Transcription factors TGAI and TGA2 with NPRI

Arabidopsis thaliana is an established model plant system for studying plantpathogen interactions. The knowledge garnered from examining the mechanism of induced disease resistance in this model system can be applied to eliminate the cost and danger associated with current means of crop protection. A specific defense pathway, known as systemic acquired resistance (SAR), involves whole plant protection from a wide variety of bacterial, viral and fungal pathogens and remains induced weeks to months after being triggered. The ability of Arabidopsis to mount SAR depends on the accumulation of salicylic acid (SA), the NPRI (non-expressor of pathogenesis related gene 1) protein and the expression of a subset of pathogenesis related (PR) genes. NPRI exerts its effect in this pathway through interaction with a closely related class of bZIP transcription factors known as TGA factors, which are named for their recognition of the cognate DNA motif TGACG. We have discovered that one of these transcription factors, TGA2, behaves as a repressor in unchallenged Arabidopsis and acts to repress NPRI-dependent activation of PRJ. TGA1, which bears moderate sequence similarity to TGA2, acts as a transcriptional activator in unchallenged Arabidopsis, however the significance of this activity is J unclear. Once SAR has been induced, TGAI and TGA2 interact with NPRI to form complexes that are capable of activating transcription. Curiously, although TGAI is capable of transactivating, the ability of the TGAI-NPRI complex to activate transcription results from a novel transactivation domain in NPRI. This transactivation domain, which depends on the oxidation of cysteines 521 and 529, is also responsible for the transactivation ability of the TGA2-NPRI complex. Although the exact mechanism preventing TGA2-NPRI interaction in unchallenged Arabidopsis is unclear, the regulation of TGAI-NPRI interaction is based on the redox status of cysteines 260 and 266 in TGAl. We determined that a glutaredoxin, which is an enzyme capable of regulating a protein's redox status, interacts with the reduced form of TGAI and this interaction results .in the glutathionylation of TGAI and a loss of interaction with NPRl. Taken together, these results expand our understanding of how TGA transcription factors and NPRI behave to regulate events and gene expression during SAR. Furthermore, the regulation of the behavior of both TGAI and NPRI by their redox status and the involvement of a glutaredoxin in modulating TGAI-NPRI interaction suggests the redox regulation of proteins is a general mechanism implemented in SAR.

Utilization of aquatic macrophyte Spirodela polyrhiza as phytotoxicological assessment and phytoremediation tool in selected polluted wetland sites in Ernakulam district

One of the objectives of the current investigation was to evaluate the effectiveness of Spirodela polyrhiza to remove heavy metals and other contaminants from the water samples collected from wetland sites of Eloor and Kannamaly under controlled conditions .The results obtained from the current study suggest that the test material S. polyrrhiza should be used in the biomonitoring and phytoremediation of municipal, agricultural and industrial effluents because of their simplicity, sensitivity and cost-effectiveness. The study throws light on the potential of this plant which can be used as an assessment tool in two diverse wetland in Ernakulum district. The results show the usefulness of combining physicochemical analysis with bioassays as such approach ensures better understanding of the toxicity of chemical pollutants and their influence on plant health. The results shows the suitability of Spirodela plant for surface water quality assessment as all selected parameters showed consistency with respect to water samples collected over a 3-monitoring periods. Similarly the relationship between the change in exposure period (2, 4 and 8 days) with the parameters were also studied in detail. Spirodela are consistent test material as they are homogeneous plant material; due to predominantly vegetative reproduction. New fronds are formed by clonal propagation thus, producing a population of genetically homogeneous plants. The result is small variability between treated individuals. It has been observed that phytoremediation of water samples collected from Eloor and Kannamaly using the floating plant system is a predominant method which is economic to construct, requires little maintenance and eco friendly.

Effects of Different Feeding Regimes on the Digestibility and Faecal Excretion of Nitrogen, Soluble Carbohydrates and Fibre Fractions in Water Buffaloes kept under Subtropical Conditions

In the course of the ‘Livestock Revolution’, extension and intensification of, among others, ruminant livestock production systems are current phenomena, with all their positive and negative side effects. Manure, one of the inevitable secondary products of livestock rearing, is a valuable source of plant nutrients and its skillful recycling to the soil-plant interface is essential for soil fertility, nutrient - and especially phosphorus - uses efficiency and the preservation or re-establishment of environmentally sustainable farming systems, for which organic farming systems are exemplarily. Against this background, the PhD research project presented here, which was embedded in the DFG-funded Research Training Group 1397 ‘Regulation of soil organic matter and nutrient turnover in organic agriculture ’ investigated possibilities to manipulate the diets of water buffalo (Bubalus bubalis L.) so as to produce manure of desired quality for organic vegetable production, without affecting the productivity of the animals used. Consisting of two major parts, the first study (chapter 2) tested the effects of diets differing in their ratios of carbon (C) to nitrogen (N) and of structural to non-structural carbohydrates on the quality of buffalo manure under subtropical conditions in Sohar, Sultanate of Oman. To this end, two trials were conducted with twelve water buffalo heifers each, using a full Latin Square design. One control and four tests diets were examined during three subsequent 7 day experimental periods preceded each by 21 days adaptation. Diets consisted of varying proportions of Rhodes grass hay, soybean meal, wheat bran, maize, dates, and a commercial concentrate to achieve a (1) high C/N and high NDF (neutral detergent fibre)/SC (soluble carbohydrate) ratio (HH), (2) low C/N and low NDF/SC ratio (LL); (3) high C/N and low NDF/SC ratio (HL) and (4) low C/N and high NDF/SC (LH) ratio. Effects of these diets, which were offered at 1.45 times maintenance requirements of metabolizable energy, and of individual diet characteristics, respectively, on the amount and quality of faeces excreted were determined and statistically analysed. The faeces produced from diets HH and LL were further tested in a companion PhD study (Mr. K. Siegfried) concerning their nutrient release in field experiments with radish and cabbage. The second study (chapter 3) focused on the effects of the above-described experimental diets on the rate of passage of feed particles through the gastrointestinal tract of four randomly chosen animals per treatment. To this end, an oral pulse dose of 683 mg fibre particles per kg live weight marked with Ytterbium (Yb; 14.5 mg Yb g-1 organic matter) was dosed at the start of the 7 day experimental period which followed 21 days of adaptation. During the first two days a sample for Yb determination was kept from each faecal excretion, during days 3 – 7 faecal samples were kept from the first morning and the first evening defecation only. Particle passage was modelled using a one-compartment age-dependent Gamma-2 model. In both studies individual feed intake and faecal excretion were quantified throughout the experimental periods and representative samples of feeds and faeces were subjected to proximate analysis following standard protocols. In the first study the organic matter (OM) intake and excretion of LL and LH buffaloes were significantly lower than of HH and HL animals, respectively. Digestibility of N was highest in LH (88%) and lowest in HH (74%). While NDF digestibility was also highest in LH (85%) it was lowest in LL (78%). Faecal N concentration was positively correlated (P≤0.001) with N intake, and was significantly higher in faeces excreted by LL than by HH animals. Concentrations of fibre and starch in faecal OM were positively affected by the respective dietary concentrations, with NDF being highest in HH (77%) and lowest in LL (63%). The faecal C/N ratio was positively related (P≤0.001) to NDF intake; C/N ratios were 12 and 7 for HH and LL (P≤0.001), while values for HL and LH were 11.5 and 10.6 (P>0.05). The results from the second study showed that dietary N concentration was positively affecting faecal N concentration (P≤0.001), while there was a negative correlation with the faecal concentration of NDF (P≤0.05) and the faecal ratios of NDF/N and C/N (P≤0.001). Particle passage through the mixing compartment was lower (P≤0.05) for HL (0.033 h-1) than for LL (0.043 h-1) animals, while values of 0.034 h-1 and 0.038 h-1 were obtained for groups LH and HH. At 55.4 h, total tract mean retention time was significantly (P≤0.05) lower in group LL that in all other groups where these values varied between 71 h (HH) and 79 h (HL); this was probably due to the high dietary N concentration of diet LL which was negatively correlated with time of first marker appearance in faeces (r= 0.84, P≤0.001), while the dietary C concentration was negatively correlated with particle passage through the mixing compartment (r= 0.57, P≤0.05). The results suggest that manure quality of river buffalo heifers can be considerably influenced by diet composition. Despite the reportedly high fibre digestion capacity of buffalo, digestive processes did not suppress the expression of diet characteristics in the faeces. This is important when aiming at producing a specific manure quality for fertilization purposes in (organic) crop cultivation. Although there was a strong correlation between the ingestion and the faecal excretion of nitrogen, the correlation between diet and faecal C/N ratio was weak. To impact on manure mineralization, the dietary NDF and N concentrations seem to be the key control points, but modulating effects are achieved by the inclusion of starch into the diet. Within the boundaries defined by the animals’ metabolic and (re)productive requirements for energy and nutrients, diet formulation may thus take into account the abiotically and biotically determined manure turnover processes in the soil and the nutrient requirements of the crops to which the manure is applied, so as to increase nutrient use efficiency along the continuum of the feed, the animal, the soil and the crop in (organic) farming systems.

Genotype x environment interaction in the uptake of Cs and Sr from soils by plants

The soil-plant transfer factors for Cs and Sr were analyzed in relationship to soil properties, crops, and varieties of crops. Two crops and two varieties of each crop: lettuce (Lactuca sativa L.), cv. Salad Bowl Green and cv. Lobjoits Green Cos, and radish (Raphanus sativus L.), cv. French Breakfast 3 and cv. Scarlet Globe, were grown on five different soils amended with Cs and Sr to give concentrations of 1 mg kg(-1) and 50 mg kg(-1) of each element. Soil-plant transfer coefficients ranged between 0.12-19.10 (Cs) and 1.48-146.10 (Sr) for lettuce and 0.09-13.24 (Cs) and 2.99-93.00 (Sr) for radish. Uptake of Cs and Sr by plants depended on both plant and soil properties. There were significant (P less than or equal to 0.05) differences between soil-plant transfer factors for each plant type at the two soil concentrations. At each soil concentration about 60% of the variance in the uptake of the Cs and Sr was due to soil properties. For a given concentration of Cs or Sr in soil, the most important factor effecting soil-plant transfer of these elements was the soil properties rather than the crops or varieties of crops. Therefore, for the varieties considered here, soil-plant transfer of Cs and Sr would be best regulated through the management of soil properties. At each concentration of Cs and Sr, the main soil properties effecting the uptake of Cs and Sr by lettuce and radish were the concentrations of K and Ca, pH and CEC. Together with the concentrations of contaminants in soils, they explained about 80% of total data variance, and were the best predictors for soil-plant transfer. The different varieties of lettuce and radish gave different responses in soil-plant transfer of Cs and Sr in different soil conditions, i.e. genotype x environment interaction caused about 30% of the variability in the uptake of Cs and Sr by plants. This means that a plant variety with a low soil-plant transfer of Cs and Sr in one soil could have an increased soil-plant transfer factor in other soils. The broad implications of this work are that in contaminated agricultural lands still used for plant growing, contaminant-excluding crop varieties may not be a reliable method for decreasing contaminant transfer to foodstuffs. Modification of soil properties would be a more reliable technique. This is particularly relevant to agricultural soils in the former USSR still affected by fallout from the Chernobyl disaster.

Cultura da soja em função da profundidade de semeadura e da carga vertical sobre a fileira de semeadura

A análise do efeito da profundidade de semeadura e carga vertical visando a melhorar o aproveitamento, e a integração entre o solo e a cultura é muito difícil. O objetivo do presente trabalho foi avaliar cargas verticais (0; 98; 196 e 294 N) sobre as rodas compactadoras das semeadoras, combinando com profundidades de semeadura (0,03; 0,05 e 0,07 m) para a cultura da soja. O trabalho foi realizado no DER/UNESP - Jaboticabal, na pista de ensaio do Laboratório de Máquinas e Mecanização Agrícola (LAMMA), utilizando o delineamento experimental em blocos casualizados, no esquema fatorial (4 x 3), com 12 tratamentos e três repetições, totalizando 36 observações. Foram analisados: emergência de plântulas, estandes inicial e final, índice de sobrevivência, área mobilizada e rendimento de grãos. Os resultados evidenciaram que, com exceção da área mobilizada em relação à profundidade de semeadura, todas as demais variáveis não foram influenciadas pelos tratamentos.

Efeito do manejo da entrelinha da seringueira sobre as propriedades químicas do solo, o estado nutricional e o crescimento

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Atributos físicos de um Latossolo Vermelho submetido a diferentes usos

The cultivation of the soil causes changes in physical attributes, depending on the intensity of preparation and management. The objective of this work was to evaluate the degree of modification of some physical properties of soil mid the S index, comparing areas of Pasture of grass Tanzania (Panicum maximum) and native forest with an area under maize (Zea mays L.) irrigated bay, a central pivot. The study was conducted in three areas within the Agency of Technology Agribusiness Paulista (APTA) Regional High Mogiana, located in Colina, SP. The experimental design was split plot in a factorial 3 x 3, with 4 replications, where the plots were installed in areas of Cultivation of corn, pasture and forest in the depths 0-0.1 m, 0.1-0.2 m 0.2-0.3 m. The physical attributes of soil were: resistance to penetration (RP), bulk density (Ds), microporosity (Micro), macroporosity (Macro), total volume of pores (VTP) and water retention in soil. The native forest had the best physical condition of soil in all parameters examined. The use of land and pasture with corn altered the physical structure of it, evidenced by the increase in penetration resistance and soil density and, reduction in macroporosity. The level of degradation of the managed soil was considered low, index S (<0035). The replacement of pasture by the corn crop in the soil tillage system provided a conventional mild improvement in soil physical characteristics.

Nitrogênio em cobertura na cultura do milho em preparo convencional e plantio direto consolidados

O nitrogênio é o nutriente exigido em maior quantidade pela cultura do milho, sendo o que mais frequentemente limita a produtividade de grãos. O objetivo do trabalho foi avaliar, em área com vinte anos (1985-2005) de estudo de sistemas de manejo de solo, na Universidade Estadual Paulista, Campus de Botucatu (SP), a resposta do milho à produtividade, características agronômicas e eficiência de uso de nitrogênio (N), em função da adubação nitrogenada em cobertura, nos sistemas de preparo convencional e plantio direto. O delineamento experimental utilizado foi o de blocos casualizados, em esquema de parcelas subdivididas, com quatro repetições. As parcelas foram representadas por preparo convencional do solo e plantio direto e as subparcelas por doses de adubação nitrogenada em cobertura (0 kg ha-1, 40 kg ha-1, 80 kg ha-1, 120 kg ha-1 e 160 kg ha-1). A adubação nitrogenada de cobertura promoveu acréscimos significativos nas características agronômicas e nutricionais do milho, com a produtividade máxima de grãos obtida com 151 kg ha-1 de N. Nas doses de 90 kg ha-1 e 145 kg ha-1 de N em cobertura, os valores da eficiência agronômica e de recuperação foram semelhantes, para o preparo convencional do solo e plantio direto, respectivamente. As produtividades de grãos e as características agronômicas e nutricionais do milho não foram afetadas pelo tipo de preparo do solo.