Soil microbial biomass under different management and tillage systems of permanent intercropped cover species in an orange orchard

To mitigate soil erosion and enhance soil fertility in orange plantations, the permanent protection of the inter-rows by cover species has been suggested. The objective of this study was to evaluate alterations in the microbial biomass, due to different soil tillage systems and intercropped cover species between rows of orange trees. The soil of the experimental area previously used as pasture (Brachiaria humidicola) was an Ultisol (Typic Paleudult) originating from Caiuá sandstone in the northwestern part of the State of Paraná, Brazil. Two soil tillage systems were evaluated: conventional tillage (CT) in the entire area and strip tillage (ST) (strip width 2 m), in combination with different ground cover management systems. The citrus cultivar 'Pera' orange (Citrus sinensis) grafted onto 'Rangpur' lime rootstock was used. Soil samples were collected after five years of treatment from a depth of 0-15 cm, under the tree canopy and in the inter-row, in the following treatments: (1) CT and an annual cover crop with the leguminous species Calopogonium mucunoides; (2) CT and a perennial cover crop with the leguminous peanut Arachis pintoi; (3) CT and an evergreen cover crop with Bahiagrass Paspalum notatum; (4) CT and a cover crop with spontaneous Brachiaria humidicola grass vegetation; and (5) ST and maintenance of the remaining grass (pasture) of Brachiaria humidicola. Soil tillage and the different cover species influenced the microbial biomass, both under the tree canopy and in the inter-row. The cultivation of brachiaria increased C and N in the microbial biomass, while bahiagrass increased P in the microbial biomass. The soil microbial biomass was enriched in N and P by the presence of ground cover species and according to the soil P content. The grass species increased C, N and P in the soil microbial biomass from the inter-row more than leguminous species.

Seasonal patterns op biomass variation of Ruppia cirrhosa (Petagna) Grande and Potamageton pectinatus L. in a coastal logoon

Coastal lagoons where salinity varies within a wide range during the year are colonized by euryhaline macrophytes which can develop extensive beds. Seasonal changes in biomass of Ruppia cirrhosa and Potamogeton pectinatus were studied in Tancada Lagoon (Ebro Delta, NE Spain) in order to reveal the environmental factors controlling their population development. Ruppia cirrhosa occupy a larger area of the lagoon than Potarnogeton pectinatus. Their maximum above ground biomasses are also different (495 g m-2 and 351 g m-2 ash free dry weight, respectively). Below ground biomass of Ruppia cirrhosa is between 9 and 53 % of the above ground biomass, while it is 3-40 % for Potamogeton pectinatus. Chlorophyll a contents show fluctuations similar to biomass. Low salinity and high turbidity caused by freshwater inflows favour Potamogeton expansion, while Ruppia development is favoured by high salinity and transparent water.

Identification and functional characterization of auxiliary enzymes of the β-oxidation in " Arabidopsis thaliana "

Abstract: The ß-oxidation is the universal pathway that allows living organisms to degrade fatty acids. leading to lipid homeostasis and carbon and energy recovery from the fatty acid molecules. This pathway is centred on four core enzymatic activities sufficient to degrade saturated fatty acids. Additional auxiliary enzymes of the ß-oxidation are necessary for the complete degradation of a larger array of molecules encompassing the unsaturated fatty acids. The main pathways of the ßoxidation of fatty acids have been investigated extensively and auxiliary enzymes are well-known in mammals and yeast. The comparison of the established ß-oxidation systems suggests that the activities that are required to proceed to the full degradation of unsaturated fatty acids are present regardless of the organism and rely on common active site templates. The precise identity of the plant enzymes was unknown. By homology searches in the genome of Arabidopsis thaliana, I identified genes. encoding for proteins that could be orthologous to the yeast or animal auxiliary enzymes Δ 3, Δ 2-enoyl-CoA isomerase, Δ 3,5, Δ 2,4 -dienoyl-CoA isomerase, and type 2 enoyl-CoA hydratase. I established that these genes are expressed in Arabidopsis and that their expression can be correlated to the expression of core ß-oxidation genes. Through the observation of chimeric fluorescent protein fusions, I demonstrated that the identified proteins are localized in the peroxisóme, the only organelle where the ß-oxidation occurs in plants. Enzymatic assays were performed with the partially purified enzymes to demonstrate that the identified enzymes can catalyze the same in vitro reactions as their non-plant orthologs. The activities in vivo of the plant enzymes were demonstrated by heterologous complementation of the corresponding yeast Saccharomyces cerevisiae mutants. The complementation was visualized using the artificial polyhydroxyalkanoate (PHA) production in yeast peroxisomes. The recombinant strains, expressing a Pseudomonas aeruginosa PHA synthase modified for a peroxisomal localization, produce this polymer that serves as a trap for the 3-hydroxyacyl-CoA intermediaries of the ßoxidation and that reflects qualitatively and quantitatively the array of molecules that are processed through the ß-oxidation. This complementation demonstrated the implication of the plant Δ 3, Δ 2-enoyl-CoA isomerases and Δ3,5, Δ2,4-dienoyl-CoA isomerase in the degradation of odd chain position unsaturated fatty acids. The presence of a monofunctional type 2 enoyl-CoA hydratase is a novel in eukaryotes. Downregulation of the corresponding gene expression in an Arabidopsis line, modified to produce PHA in the peroxisome, demonstrated thàt this enzyme participates in vivo to the conversion of the intermediate 3R-hydroxyacyl-CoA, generated by the metabolism of fatty acids with a cis (Z)-unsaturated bond on an even-numbered carbon, to the 2Eenoyl-CoA for further degradation through the core ß-oxidation cycle. Résumé: La ß-oxydation est une voie universelle de dégradation des acides gras qui permet aux organismes vivants d'assurer une homéostasie lipidique et de récupérer l'énergie et le carbone contenus dans les acides gras. Le coeur de cette voie est composé de quatre réactions enzymatiques suffisantes à la dégradation des acides gras saturés. La présence des enzymes auxiliaires de la ß-oxydation est nécessaire à la dégradation d'une gamme plus étendue de molécules comprenant les acides gras insaturés. Les voies principales de la ß-oxydation des acides gras ont été étudiées en détail et les enzymes auxiliaires sont déterminées chez les mammifères et la levure. La comparaison entre les systèmes de ß-oxydation connus suggère que les activités requises pour la dégradation complète des acides gras insaturés reposent sur la présence de site actifs similaires. L'identité précise des enzymes auxiliaires chez les plantes était inconnue. En cherchant par homologie dans le génome de la plante modèle Arabidopsis thaliana, j'ai identifié des gènes codant pour des protéines pouvant être orthologues aux enzymes auxiliaires Δ3 Δ2-enoyl-CoA isomérase, Δ 3,5 Δ 2,4-dienoyl-CoA isomérase et enoyl-CoA hydratase de type 2 d'origine fongique ou mammalienne. J'ai établi la corrélation de l'expression de ces gènes dans Arabidopsis avec celle de gènes des enzymes du coeur de la ß-oxydation. En observant des chimères de fusion avec des protéines fluorescentes, j'ai démontré que les protéines identifiées sont localisées dans le péroxysomes, le seul organelle où la ß-oxydation se déroule chez les plantes. Des essais enzymatiques ont été conduits avec ces enzymes partiellement purifiées pour démontrer que les enzymes identifiées sont capables de catalyser in vitro les mêmes réactions que leurs orthologues non végétaux. Les activités des enzymes végétales in vivo ont été .démontrées par complémentation hétérologue des mutants de délétion correspondants de levure Saccharomyces cerevisiae. La visualisation de la complémentation est rendue possible par la synthèse de polyhydroxyalcanoate (PHA) dans les péroxysomes de levure. Les souches recombinantes expriment la PHA synthase de Pseudomonas aeruginosa modifiée pour être localisée dans le péroxysome produisent ce polymère qui sert de piège pour les 3-hydroxyacylCoAs intermédiaires de la ß-oxydation et qui reflète qualitativement et quantitativement la gamme de molécules qui subit la ß-oxydation. Cette complémentation a permis de démontrer que les Δ3, Δ2-enoyl-CoA isomérases, et la Δ3.5, Δ2,4-dienoyl-CoA isomérase végétales sont impliquées dans la dégradation des acides gras insaturés en position impaire. L'enoyl-CoA hydratase de type 2 monofonctionelle est une enzyme nouvelle chez les eucaryotes. La sous-expression du gène correspondant dans une lignée d'Arabidopsis modifiée pour produite du PHA dans le péroxysome a permis de démontrer que cette enzyme participe in vivo à la dégradation des acides gras ayant une double liaison en conformation cis (Z) en position paire.

Distribution profile of zwitterions and hydrolysis of esters derived from N-benzylpiperazine

Résumé Les esters sont des agents thérapeutiques largement utilisés comme médicaments et prodrogues. Leurs dégradation est chimique et enzymatique. Le Chapitre IV de cette thèse a comme objet l'hydrolyse chimique de plusieurs dérivés esters du 2,3-dimethoxyphenol. Des composés modèles ont été synthétisés dans le but de déterminer leur mécanismes de dégradation. Les profils d'ionisation et d'hydrolyse de ces composés ont permis d'identifier la présence d'une catalyse intramoléculaire basique par un atome d'azote non-protoné. Les effets électroniques exercés par les groupes phenylethenyle et phenylcyclopropyle influencent également la vitesse d'hydrolyse des esters. La résolution des problèmes liés à l'adsorption et la perméation est devenue à nos jours l'étape limitante dans la conception de nouveaux médicaments car de trop nombreux candidats prometteurs ont échoué à cause d'une mauvaise biodisponibilité. La lipophilie décrit le partage d'un médicament entre une membrane lipidique et son environnement physiologique aqueux, et de ce fait elle influence sa pharmacocinétique. Des études récents ont mis en évidence l'importance de la détermination de la lipophilie des espèces ionisées vu leur considérable impact biologique. Le Chapitre V de cette thèse est centré sur une classe particulière de composés ionisables, les zwitterions. Plusieurs methoxybenzylpiperazines de nature zwitterionique ont été étudiées. Leurs profils d'ionisation ont montré que dans un large intervalle de pH, l'espèce prédominante est le zwitterion. Les profils de lipophilie ont montré que leur lipophilie est plus élevée que celles des zwitterions courants. Une interaction électrostatique entre l'oxygène du carboxylate et l'azote protoné est responsable de ce profil et rend la plupart des zwitterions non-donneurs de liaison hydrogène. Ces deux aspects peuvent favoriser le passage de la barrière hémato-éncephalique. Les données biologiques ont par la suite confirmé cette hypothèse pour un certain nombre de composés. Résumé large public Les esters sont des composés souvent rencontrés en chimie thérapeutique. Ils sont dégradés en milieu aqueux par une réaction d'hydrolyse, avec ou sans la participation d'enzymes. Dans ce travail de thèse, une série d'esters ont été étudiés dans le but d'établir une relation entre leur structure et les mécanismes responsables de leur dégradation chimique. Il a été prouvé que la dégradation est accélérée par un atome d'azote non-protoné. D'autres mécanismes peuvent intervenir en fonction du pH du milieu. La présence d'une liaison simple ou double ou d'un groupe phenylcyclopropyle peut également influencer la vitesse de dégradation. Il est essentiel, dans la conception de nouveaux médicaments, d'optimiser les étapes qui influencent leur distribution dans le corps. Ce dernier peut être visualisé comme une série infinie de compartiments aqueux séparés par des membranes lipidiques. La lipophilie est une propriété moléculaire importante qui décrit le passage des barrières rencontrées par les médicaments. Des études récentes ont mis en évidence l'importance de déterminer la lipophilie des espèces ionisées vu leur considérable impact biologique. Dans ce travail de thèse a été étudiée une série particulière de composés ionisables , les zwitterions. Une relation a été établie entre leur structure et leur proprietés physico-chimiques. Une lipophilie plus élevée par rapport à celle des zwitterions courants a été trouvée. Une interaction entre les groupes chargés des zwitterions étudiés est responsable de ce comportement inattendu et rend la plupart d'entre eux non-donneurs de liaison hydrogène. Ces deux facteurs peuvent favoriser la pénétration cérébrale. Les données biologiques ont confirmé cette hypothèse pour un certain nombre de composés. Summary Esters are often encountered in medicinal chemistry. Their hydrolysis may be chemical as well as enzymatic. Chapter IV of this manuscript provides a mechanistic insight into the chemical hydrolysis of a particular series of basic esters derived from 2,3-dimethoxyphenol. Their ionization and pH-rate profiles allowed to identify the presence of an intramolecular base catalysis by a non-protonated nitrogen atom. Electronic effects exerted by the phenylethenyl and phenylcyclopropyl groups that are present in the structure of the esters also influenced their rate of hydrolysis. Numerous works in the literature witness of the importance of lipophilicity in determining the fate of a drug. Most published partition coefficients are those of neutral species. In contrast, no exhaustive treatment of the lipophilicity of charged molecules is available at present, and a lack of information characterizes in particular zwitterions. Chapter V of this manuscript provides an insight into the physicochemical parameters of a series of zwitterionic methoxybenzylpiperazines. Their ionization profiles showed that they exist predominantly in the zwitterionic form in a broad pH-range. An electrostatic interaction between the oxygen of the carboxylate and the protonated nitrogen atom is increases the lipophilicity of the investigated zwitterions, and prevents the majority of them to express their hydrogen-bonding capacity. These two aspects may favor the crossing of the blood-brain barrier. The available ratios PSt/PSf measured in vitro have confirmed this point for a number of compounds.

The design and characterization of receptor-selective APRIL variants.

A proliferation-inducing ligand (APRIL), a member of the TNF ligand superfamily with an important role in humoral immunity, is also implicated in several cancers as a prosurvival factor. APRIL binds two different TNF receptors, B cell maturation antigen (BCMA) and transmembrane activator and cylclophilin ligand interactor (TACI), and also interacts independently with heparan sulfate proteoglycans. Because APRIL shares binding of the TNF receptors with B cell activation factor, separating the precise signaling pathways activated by either ligand in a given context has proven quite difficult. In this study, we have used the protein design algorithm FoldX to successfully generate a BCMA-specific variant of APRIL, APRIL-R206E, and two TACI-selective variants, D132F and D132Y. These APRIL variants show selective activity toward their receptors in several in vitro assays. Moreover, we have used these ligands to show that BCMA and TACI have a distinct role in APRIL-induced B cell stimulation. We conclude that these ligands are useful tools for studying APRIL biology in the context of individual receptor activation.

Wet Oxidation of Concentrated Wastewaters: Process Combination and Reaction Kinetic Modeling

The accumulation of aqueous pollutants is becoming a global problem. The search for suitable methods and/or combinations of water treatment processes is a task that can slow down and stop the process of water pollution. In this work, the method of wet oxidation was considered as an appropriate technique for the elimination of the impurities present in paper mill process waters. It has been shown that, when combined with traditional wastewater treatment processes, wet oxidation offers many advantages. The combination of coagulation and wet oxidation offers a new opportunity for the improvement of the quality of wastewater designated for discharge or recycling. First of all, the utilization of coagulated sludge via wet oxidation provides a conditioning process for the sludge, i.e. dewatering, which is rather difficult to carry out with untreated waste. Secondly, Fe2(SO4)3, which is employed earlier as a coagulant, transforms the conventional wet oxidation process into a catalytic one. The use of coagulation as the post-treatment for wet oxidation can offer the possibility of the brown hue that usually accompanies the partial oxidation to be reduced. As a result, the supernatant is less colored and also contains a rather low amount of Fe ions to beconsidered for recycling inside mills. The thickened part that consists of metal ions is then recycled back to the wet oxidation system. It was also observed that wet oxidation is favorable for the degradation of pitch substances (LWEs) and lignin that are present in the process waters of paper mills. Rather low operating temperatures are needed for wet oxidation in order to destruct LWEs. The oxidation in the alkaline media provides not only the faster elimination of pitch and lignin but also significantly improves the biodegradable characteristics of wastewater that contains lignin and pitch substances. During the course of the kinetic studies, a model, which can predict the enhancements of the biodegradability of wastewater, was elaborated. The model includes lumped concentrations suchas the chemical oxygen demand and biochemical oxygen demand and reflects a generalized reaction network of oxidative transformations. Later developments incorporated a new lump, the immediately available biochemical oxygen demand, which increased the fidelity of the predictions made by the model. Since changes in biodegradability occur simultaneously with the destruction of LWEs, an attempt was made to combine these two facts for modeling purposes.

Formation and Control of Trace Metal Emissions in Co-Firing of Biomass, Peat, and Wastes in Fluidised Bed Combustors

Environmentally harmful consequences of fossil fuel utilisation andthe landfilling of wastes have increased the interest among the energy producers to consider the use of alternative fuels like wood fuels and Refuse-Derived Fuels, RDFs. The fluidised bed technology that allows the flexible use of a variety of different fuels is commonly used at small- and medium-sized power plants ofmunicipalities and industry in Finland. Since there is only one mass-burn plantcurrently in operation in the country and no intention to build new ones, the co-firing of pre-processed wastes in fluidised bed boilers has become the most generally applied waste-to-energy concept in Finland. The recently validated EU Directive on Incineration of Wastes aims to mitigate environmentally harmful pollutants of waste incineration and co-incineration of wastes with conventional fuels. Apart from gaseous flue gas pollutants and dust, the emissions of toxic tracemetals are limited. The implementation of the Directive's restrictions in the Finnish legislation is assumed to limit the co-firing of waste fuels, due to the insufficient reduction of the regulated air pollutants in the existing flue gas cleaning devices. Trace metals emission formation and reduction in the ESP, the condensing wet scrubber, the fabric filter, and the humidification reactor were studied, experimentally, in full- and pilot-scale combustors utilising the bubbling fluidised bed technology, and, theoretically, by means of reactor model calculations. The core of the model is a thermodynamic equilibrium analysis. The experiments were carried out with wood chips, sawdust, and peat, and their refuse-derived fuel, RDF, blends. In all, ten different fuels or fuel blends were tested. Relatively high concentrations of trace metals in RDFs compared to the concentrations of these metals in wood fuels increased the trace metal concentrations in the flue gas after the boiler ten- to hundred-folds, when RDF was co-fired with sawdust in a full-scale BFB boiler. In the case of peat, lesser increase in trace metal concentrations was observed, due to the higher initial trace metal concentrations of peat compared to sawdust. Despite the high removal rate of most of the trace metals in the ESP, the Directive emission limits for trace metals were exceeded in each of the RDF co-firing tests. The dominat trace metals in fluegas after the ESP were Cu, Pb and Mn. In the condensing wet scrubber, the flue gas trace metal emissions were reduced below the Directive emission limits, whenRDF pellet was used as a co-firing fuel together with sawdust and peat. High chlorine content of the RDFs enhanced the mercuric chloride formation and hence the mercury removal in the ESP and scrubber. Mercury emissions were lower than theDirective emission limit for total Hg, 0.05 mg/Nm3, in all full-scale co-firingtests already in the flue gas after the ESP. The pilot-scale experiments with aBFB combustor equipped with a fabric filter revealed that the fabric filter alone is able to reduce the trace metal concentrations, including mercury, in the flue gas during the RDF co-firing approximately to the same level as they are during the wood chip firing. Lower trace metal emissions than the Directive limits were easily reached even with a 40% thermal share of RDF co-firing with sawdust.Enrichment of trace metals in the submicron fly ash particle fraction because of RDF co-firing was not observed in the test runs where sawdust was used as the main fuel. The combustion of RDF pellets with peat caused an enrichment of As, Cd, Co, Pb, Sb, and V in the submicron particle mode. Accumulation and release oftrace metals in the bed material was examined by means of a bed material analysis, mass balance calculations and a reactor model. Lead, zinc and copper were found to have a tendency to be accumulated in the bed material but also to have a tendency to be released from the bed material into the combustion gases, if the combustion conditions were changed. The concentration of the trace metal in the combustion gases of the bubbling fluidised bed boiler was found to be a summary of trace metal fluxes from three main sources. They were (1) the trace metal flux from the burning fuel particle (2) the trace metal flux from the ash in the bed, and (3) the trace metal flux from the active alkali metal layer on the sand (and ash) particles in the bed. The amount of chlorine in the system, the combustion temperature, the fuel ash composition and the saturation state of the bed material in regard to trace metals were discovered to be key factors affecting therelease process. During the co-firing of waste fuels with variable amounts of e.g. ash and chlorine, it is extremely important to consider the possible ongoingaccumulation and/or release of the trace metals in the bed, when determining the flue gas trace metal emissions. If the state of the combustion process in regard to trace metals accumulation and/or release in the bed material is not known,it may happen that emissions from the bed material rather than the combustion of the fuel in question are measured and reported.

Efficacy of the fluorescent dyes Fast Blue, Fluoro-Gold, and Diamidino Yellow for retrograde tracing to dorsal root ganglia after subcutaneous injection

The present study was designed to investigate the efficacy of the fluorescent dyes Fast Blue (FB), Fluoro-Gold (FG), and Diamidino Yellow (DY) for retrograde tracing of lumbar dorsal root ganglia after their subcutaneous injection into different hindlimb digits. Injection of equal volumes (0.5 mu l) of 5% FB or 2% FG resulted in similar mean numbers of sensory neurones labelled by each tracer. Injection of equal volumes (0.5 mu l) of FB or FG in a single digit followed 10 days later by a second injection of the same volume of 5% DY into the same digit resulted in similar mean numbers of labelled sensory neurones for each of the three tracers. Furthermore, on average, 75% of all the FB-labelled cells and 74% of all FC-labelled cells also contained DY. Repeating the same experiment with an increased volume of DY (1.5 mu l) resulted in an increase in the mean number of double-labelled profiles to 82 and 84% for FB and FG, respectively. The results show that FB, FG and DY label similar numbers of cutaneous afferents and that a high level of double labelling may be obtained after sequential injections in digits. These properties make them suitable candidates in investigations where a combination of tracers with similar labelling efficacies is needed.

Market of biomass fuels in Finland : IEA Bioenergy Task 40 and EUBIONET III - Country report of Finland 2009

This study considered the current situation of solid and liquid biomass fuels in Finland. The fact that industry consumes more than half of the total primary energy, widely applied combined heat and power production and a high share of solid biomass fuels in the total energy consumption are specific to the Finnish energy system. Wood is the most important source of bioenergy in Finland, representing 20% of the total energy consumption in 2007. Almost 80% of the woodbased energy is recovered from industrial by-products and residues. As a member of the European Union, Finland has committed itself to the Union’s climate and energy targets, such as reducing its overall emissions of green house gases to at least 20% below 1990 levels by 2020, and increasing the share of renewable energy in the gross final consumption. The renewable energy target approved for Finland is 38%. The present National Climate and Energy Strategy was introduced in November 2008. The strategy covers climate and energy policy measures up to 2020, and in brief thereafter, up to 2050. In recent years, the actual emissions have exceeded the Kyoto commitment and the trend of emissions is on the increase. In 2007, the share of renewable energy in the gross final energy consumption was approximately 25% (360 PJ). Without new energy policy measures, the final consumption of renewable energy would increase to 380 PJ, which would be approximately only 31% of the final energy consumption. In addition, green house gas emissions would exceed the 1990 levels by 20%. Meeting the targets will need the adoption of more active energy policy measures in coming years. The international trade of biomass fuels has a substantial importance for the utilisation of bioenergy in Finland. In 2007, the total international trading of solid and liquid biomass fuels was approximately 77 PJ, of which import was 62 PJ. Most of the import is indirect and takes place within the forest industry’s raw wood imports. In 2007, as much as 21% of wood energy was based on foreign-origin wood. Wood pellets and tall oil form the majority of export streams of biomass fuels. The indirect import of wood fuels peaked in 2006 to 61 PJ. The foreseeable decline in raw wood import to Finland will decrease the indirect import of wood fuels. In 2004– 2007, the direct trade of solid and liquid biomass fuels has been on a moderate growth path. In 2007, the import of palm oil and export of bio-diesel emerged, as a large, 170 000 t/yr biodiesel plant came into operation in Porvoo.

Influence of chloride-mediated oxidation on the electrochemical degradation of the direct black 22 dye using boron-doped diamond and β-PbO2 anodes

The Direct Black 22 dye was electrooxidized at 30 mA cm-2 in a flow cell using a BDD or β-PbO2 anode, varying pH (3, 7, 11), temperature (10, 25, 45 °C), and [NaCl] (0 or 1.5 g L-1). In the presence of NaCl, decolorization rates were similar for all conditions investigated, but much higher than predicted through a theoretical model assuming mass-transport control; similar behavior was observed for COD removal (at pH 7, 25 °C), independently of the anode. With no NaCl, COD removals were also higher than predicted with a theoretical model, which suggests the existence of distinct dye degradation pathways.

Wet oxidation of recalcitrant lignin waters: Experimental and kinetic studies

The dissertation is based on four articles dealing with recalcitrant lignin water purification. Lignin, a complicated substance and recalcitrant to most treatment technologies, inhibits seriously pulp and paper industry waste management. Therefore, lignin is studied, using WO as a process method for its degradation. A special attention is paid to the improvement in biodegradability and the reduction of lignin content, since they have special importance for any following biological treatment. In most cases wet oxidation is not used as a complete ' mineralization method but as a pre treatment in order to eliminate toxic components and to reduce the high level of organics produced. The combination of wet oxidation with a biological treatment can be a good option due to its effectiveness and its relatively low technology cost. The literature part gives an overview of Advanced Oxidation Processes (AOPs). A hot oxidation process, wet oxidation (WO), is investigated in detail and is the AOP process used in the research. The background and main principles of wet oxidation, its industrial applications, the combination of wet oxidation with other water treatment technologies, principal reactions in WO, and key aspects of modelling and reaction kinetics are presented. There is also given a wood composition and lignin characterization (chemical composition, structure and origin), lignin containing waters, lignin degradation and reuse possibilities, and purification practices for lignin containing waters. The aim of the research was to investigate the effect of the operating conditions of WO, such as temperature, partial pressure of oxygen, pH and initial concentration of wastewater, on the efficiency, and to enhance the process and estimate optimal conditions for WO of recalcitrant lignin waters. Two different waters are studied (a lignin water model solution and debarking water from paper industry) to give as appropriate conditions as possible. Due to the great importance of re using and minimizing the residues of industries, further research is carried out using residual ash of an Estonian power plant as a catalyst in wet oxidation of lignin-containing water. Developing a kinetic model that includes in the prediction such parameters as TOC gives the opportunity to estimate the amount of emerging inorganic substances (degradation rate of waste) and not only the decrease of COD and BOD. The degradation target compound, lignin is included into the model through its COD value (CODligning). Such a kinetic model can be valuable in developing WO treatment processes for lignin containing waters, or other wastewaters containing one or more target compounds. In the first article, wet oxidation of "pure" lignin water was investigated as a model case with the aim of degrading lignin and enhancing water biodegradability. The experiments were performed at various temperatures (110 -190°C), partial oxygen pressures (0.5 -1.5 MPa) and pH (5, 9 and 12). The experiments showed that increasing the temperature notably improved the processes efficiency. 75% lignin reduction was detected at the lowest temperature tested and lignin removal improved to 100% at 190°C. The effect of temperature on the COD removal rate was lower, but clearly detectable. 53% of organics were oxidized at 190°C. The effect of pH occurred mostly on lignin removal. Increasing the pH enhanced the lignin removal efficiency from 60% to nearly 100%. A good biodegradability ratio (over 0.5) was generally achieved. The aim of the second article was to develop a mathematical model for "pure" lignin wet oxidation using lumped characteristics of water (COD, BOD, TOC) and lignin concentration. The model agreed well with the experimental data (R2 = 0.93 at pH 5 and 12) and concentration changes during wet oxidation followed adequately the experimental results. The model also showed correctly the trend of biodegradability (BOD/COD) changes. In the third article, the purpose of the research was to estimate optimal conditions for wet oxidation (WO) of debarking water from the paper industry. The WO experiments were' performed at various temperatures, partial oxygen pressures and pH. The experiments showed that lignin degradation and organics removal are affected remarkably by temperature and pH. 78-97% lignin reduction was detected at different WO conditions. Initial pH 12 caused faster removal of tannins/lignin content; but initial pH 5 was more effective for removal of total organics, represented by COD and TOC. Most of the decrease in organic substances concentrations occurred in the first 60 minutes. The aim of the fourth article was to compare the behaviour of two reaction kinetic models, based on experiments of wet oxidation of industrial debarking water under different conditions. The simpler model took into account only the changes in COD, BOD and TOC; the advanced model was similar to the model used in the second article. Comparing the results of the models, the second model was found to be more suitable for describing the kinetics of wet oxidation of debarking water. The significance of the reactions involved was compared on the basis of the model: for instance, lignin degraded first to other chemically oxidizable compounds rather than directly to biodegradable products. Catalytic wet oxidation of lignin containing waters is briefly presented at the end of the dissertation. Two completely different catalysts were used: a commercial Pt catalyst and waste power plant ash. CWO showed good performance using 1 g/L of residual ash gave lignin removal of 86% and COD removal of 39% at 150°C (a lower temperature and pressure than with WO). It was noted that the ash catalyst caused a remarkable removal rate for lignin degradation already during the pre heating for `zero' time, 58% of lignin was degraded. In general, wet oxidation is not recommended for use as a complete mineralization method, but as a pre treatment phase to eliminate toxic or difficultly biodegradable components and to reduce the high level of organics. Biological treatment is an appropriate post treatment method since easily biodegradable organic matter remains after the WO process. The combination of wet oxidation with subsequent biological treatment can be an effective option for the treatment of lignin containing waters.

Effect of extracts from citric biomass, rusted coffee leaves and coffee berry husks on Phoma costarricencis of coffee plants

Phoma leaf spot, caused by Phoma costarricensis poses a serious threat to coffee (Coffea arabica) production, especially in the highlands of the state of Minas Gerais, Brazil. Extracts of citric biomass, coffee berry husks and coffee leaves severely affected by rust caused by Hemileia vastatrix, were evaluated against P. costarricensis. In an in vitro assay, aqueous extracts of rusted leaves and berry husks plus the commercial extracts based on citric biomass named Ecolife® and Agromil® were tested at various dilutions on the mycelial growth inhibition of P. costarricensis. In vivo, coffee seedlings maintained in glasshouse, were sprayed with these extracts seven days before inoculation of P. costarricensis. Only extracts from citric biomass had inhibitory effects on the fungus. In vivo, Ecolife® (5 ml/l), Agromil® (5 g/l) and the aqueous extract of rusted coffee leaves (dilution 1:6) reduced Phoma leaf spot. Both, Ecolife® and the extract of rusted coffee leaves were significantly more effective in reducing the area under the lesion progress curve when applied at lower doses, indicating a possible effect on the induction of resistance.

Use of preclinical and early clinical data for dose selection of a selective estrogen receptor modulator toremifene in treatment of breast cancer

In development of human medicines, it is important to predict early and accurately enough the disease and patient population to be treated as well as the effective and safe dose range of the studied medicine. This is pursued by using preclinical research models, clinical pharmacology and early clinical studies with small sample sizes. When successful, this enables effective development of medicines and reduces unnecessary exposure of healthy subjects and patients to ineffectice or harmfull doses of experimental compounds. Toremifene is a selective estrogen receptor modulator (SERM) used for treatment of breast cancer. Its development was initiated in 1980s when selection of treatment indications and doses were based on research in cell and animal models and on noncomparative clinical studies including small number of patients. Since the early development phase, the treatment indication, the patient population and the dose range were confirmed in large comparative clinical studies in patients. Based on the currently available large and long term clinical study data the aim of this study was to investigate how the early phase studies were able to predict the treatment indication, patient population and the dose range of the SERM. As a conclusion and based on the estrogen receptor mediated mechanism of action early studies were able to predict the treatment indication, target patient population and a dose range to be studied in confirmatory clinical studies. However, comparative clinical studies are needed to optimize dose selection of the SERM in treatment of breast cancer.

A new climatic periodisation of the Gold and Guinea Coasts in West Africa, 1750-1798 : a reconstruction of the climate during the slave trade era, including an analysis of the climatically facilitated Trans-Atlantic slave trade

Avsikten med studien är att producera den första rekonstruktionen av det västafrikanska klimatet mellan 1750 och 1798. Kunskapen om det västafrikanska klimatet före 1800-talet är till dags dato bristfällig, vilket gör det svårare att förstå framtida klimatvariationer. Det är bristen på instrumentell meteorologisk data (temperatur, regnmängd, och lufttryck), vilket i princip bara täcker det senaste århundradet, som är orsaken till att tidigare klimat är bristfälligt kartlagda. Klimatet och miljön är även sådana att proxydata från ’naturens arkiv’ (såsom t.ex. trädringar) har begränsad användning. Således är historiska dokument, främst från gästande kulturer/nationer/intressenter, innehållande deskriptiv information om vädret och klimatet, klimatforskarens viktigaste källa. Genom att använda tidigare, för det här syftet, oanvända källor påvisade den här undersökningen att klimatet i västra Afrika och Guldkusten (Ghana) har ändrats sedan 1700-talet. Monsunregnen var svagare och kortvarigare, speciellt den sekundära regnperioden under hösten var betydligt svagare än idag. Det förekom kraftiga årliga variationer i monsunregnen, men sett ur längre tidsperspektiv utmärktes torrare och blötare perioder. Studien kunde också visa en viss korrelation mellan det globala väderfenomenet El Niño och regnperiodens intensitet längs med kusten. Flera torrperioder sammanföll med tidigare registrerade El Niño sekvenser. Speciellt slutet av 1760-talet påverkades kraftigt av El Niño och även det globala klimatet verkar ha genomgått graftiga förändringar just dessa år. På basis av den nya klimatrekonstruktionen genomfördes också en jämförelse av klimatets inverkan på den transatlantiska slavhandeln från 1750 till 1798, en fråga som historikerna gjort anspelningar på i över 30 år. Utförseln av slavar från västra Afrika var som kraftigast under 1700-talets andra hälft. Analysen visade att slavhandeln delvis tilltog i samband med klimatanomalierna.