Analysis of clogging in constructed wetlands using magnetic resonance

In this work we demonstrate the potential of permanent magnet based magnetic resonance sensors to monitor and assess the extent of pore clogging in water filtration systems. The performance of the sensor was tested on artificially clogged gravel substrates and on gravel bed samples from constructed wetlands used to treat wastewater. Data indicate that the spin lattice relaxation time is linearly related to the hydraulic conductivity in such systems. In addition, within biologically active filters we demonstrate the ability to determine the relative ratio of biomass to abiotic solids, a measurement which is not possible using alternative techniques. © 2011 The Royal Society of Chemistry.

A nanoliter volume nuclear magnetic resonance (NMR) system using tunneling magneto-resistive (TMR) sensors to recognize biomolecules

The need to incorporate advanced engineering tools in biology, biochemistry and medicine is in great demand. Many of the existing instruments and tools are usually expensive and require special facilities.^ With the advent of nanotechnology in the past decade, new approaches to develop devices and tools have been generated by academia and industry. ^ One such technology, NMR spectroscopy, has been used by biochemists for more than 2 decades to study the molecular structure of chemical compounds. However, NMR spectrometers are very expensive and require special laboratory rooms for their proper operation. High magnetic fields with strengths in the order of several Tesla make these instruments unaffordable to most research groups.^ This doctoral research proposes a new technology to develop NMR spectrometers that can operate at field strengths of less than 0.5 Tesla using an inexpensive permanent magnet and spin dependent nanoscale magnetic devices. This portable NMR system is intended to analyze samples as small as a few nanoliters.^ The main problem to resolve when downscaling the variables is to obtain an NMR signal with high Signal-To-Noise-Ratio (SNR). A special Tunneling Magneto-Resistive (TMR) sensor design was developed to achieve this goal. The minimum specifications for each component of the proposed NMR system were established. A complete NMR system was designed based on these minimum requirements. The goat was always to find cost effective realistic components. The novel design of the NMR system uses technologies such as Direct Digital Synthesis (DDS), Digital Signal Processing (DSP) and a special Backpropagation Neural Network that finds the best match of the NMR spectrum. The system was designed, calculated and simulated with excellent results.^ In addition, a general method to design TMR Sensors was developed. The technique was automated and a computer program was written to help the designer perform this task interactively.^

Modelagem e análise dinâmica de um sistema de conversão de energia eólica dotado de gerador síncrono de imã permanente utilizando a plataforma ATP

Human development requires a broad balance between ecological, social and economic factors in order to ensure its own sustainability. In this sense, the search for new sources of energy generation, with low deployment and operation costs, which cause the least possible impact to the environment, has been the focus of attention of all society segments. To do so, the reduction in exploration of fossil fuels and the encouragement of using renewable energy resources for distributed generation have proved interesting alternatives to the expansion of the energy matrix of various countries in the world. In this sense, the wind energy has acquired an increasingly significant role, presenting increasing rates of power grid penetration and highlighting technological innovations such as the use of permanent magnet synchronous generators (PMSG). In Brazil, this fact has also been noted and, as a result, the impact of the inclusion of this source in the distribution and sub-transmission power grid has been a major concern of utilities and agents connected to Brazilian electrical sector. Thus, it is relevant the development of appropriate computational tools that allow detailed predictive studies about the dynamic behavior of wind farms, either operating with isolated load, either connected to the main grid, taking also into account the implementation of control strategies for active/reactive power generation and the keeping of adequate levels of voltage and frequency. This work fits in this context since it comprises mathematical and computational developments of a complete wind energy conversion system (WECS) endowed with PMSG using time domain techniques of Alternative Transients Program (ATP), which prides itself a recognized reputation by scientific and academic communities as well as by electricity professionals in Brazil and elsewhere. The modeling procedures performed allowed the elaboration of blocks representing each of the elements of a real WECS, comprising the primary source (the wind), the wind turbine, the PMSG, the frequency converter, the step up transformer, the load composition and the power grid equivalent. Special attention is also given to the implementation of wind turbine control techniques, mainly the pitch control responsible for keeping the generator under the maximum power operation point, and the vector theory that aims at adjusting the active/reactive power flow between the wind turbine and the power grid. Several simulations are performed to investigate the dynamic behavior of the wind farm when subjected to different operating conditions and/or on the occurrence of wind intensity variations. The results have shown the effectiveness of both mathematical and computational modeling developed for the wind turbine and the associated controls.

Entwicklung eines Lineardirektantriebs für Transportbänder

Transportbandsyteme werden im Bereich der Intralogistik zur Förderung von Stück- sowie leichten Schüttgütern eingesetzt. Der Antrieb der Transportbänder erfolgt dabei üblicherweise kraftschlüssig über die Antriebstrommel. Der Einsatz von Lineardirektantrieben ermöglicht als Antriebsalternative die Erzeugung der Vorschubkräfte und die Krafteinleitung in das Transportband über der Länge des Lineardirektantriebs verteilt. Dadurch lässt sich die Transportbandvorspannung erheblich reduzieren und damit auch ein leichteres und kostengünstigeres Transportband im Vergleich zu konventionellen Antriebskonzepten verwenden. Basierend auf vorherigen Untersuchungen wurde ein Lineardirektantrieb auf Basis eines Hybridmotors entwickelt, welcher die Vorteile permanentmagneterregter Maschinen mit denen der Reluktanzmotorprinzipien vereint. Auf Grundlage der durch Simulation ermittelten Kraftentfaltkungscharakteristik des Linearmotors auf die Läuferelemente wurden verschiedene Konzepte zur Befestigung dieser Läuferelemente entwickelt, untersucht und erprobt. Aufgrund der Elastizität von Transportbändern sind zudem alternative Führungskonzepte erforderlich, da geometrische Abweichungen der am Transportband befestigten Läuferelemente zu hohen Verlusten durch Reibung führen. Unterschiedliche Führungskonzepte, belegt durch Messungen, geben einen Ausblick auf den linearmotorischen Antrieb.

Sistema de emulação de aerogeradores para aplicação em geração distribuída de energia elétrica

Power generation from alternative sources is at present the subject of numerous research and development in science and industry. Wind energy stands out in this scenario as one of the most prominent alternative in the generation of electricity, by its numerous advantages. In research works, computer reproduction and experimental behavior of a wind turbine are very suitable tools for the development and study of new technologies and the use of wind potential of a given region. These tools generally are desired to include simulation of mechanical and electrical parameters that directly affect the energy conversion. This work presents the energy conversion process in wind systems for power generation, in order to develop a tool for wind turbine emulation testing experimental, using LabVIEW® software. The purpose of this tool is to emulate the torque developed in an axis wind turbine. The physical setup consists of a three phase induction motor and a permanent magnet synchronous generator, which are evaluated under different wind speed conditions. This tool has the objective to be flexible to other laboratory arrangements, and can be used in other wind power generation structures in real time. A modeling of the wind power system is presented, from the turbine to the electrical generator. A simulation tool is developed using Matlab/Simulink® with the purpose to pre-validate the experiment setup. Finally, the design is implemented in a laboratory setup.

Desenvolvimento de magnetizador para tratamento magnético da água

Dissertação (mestrado)—Universidade de Brasília, Faculdade Gama, Programa de Pós-Graduação em Engenharia Biomédica, 2015.

Obtenção de nanopartículas de hexaferrita de bário pelo método pechini

In this study barium hexaferrite was (general formulae BaFe12O19) was synthesized by the Pechini method under different conditions of heat treatment. Precursors like barium carbonate and iron nitrate were used. These magnetic ceramic, with magnetoplumbite type structure, are widely used as permanent magnet because of its excellent magnetic properties, such as: high Curie temperature, good magnetic anisotropy, high coercivity and corrosion resistance. The samples were characterized by thermal analysis (DTA and TG), X- ray Diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), Scanning Electron Microscopy (SEM) end Vibrating sample Magnetometer (VSM). The results confirm the expected phase, which was reinforced according to our analysis. A single phase powder at relatively high temperatures with particle sizes around 100 nm was obtained. The characteristic magnetic behavior one of the phases has been noted (probably superparamagnetic material), while another phase was identified as a ferrimagnetic material. The ferrimagnetic phase showed vortex configuration with two central and slightly inclined plateaus. In general, increase of heat treatment temperature and time, directly influenced the technological properties of the samples

A low frequency MEMS energy harvester scavenging energy from magnetic field surrounding an AC current-carrying wire

This paper reports on a low frequency piezoelectric energy harvester that scavenges energy from a wire carrying an AC current. The harvester is described, fabricated and characterized. The device consists of a silicon cantilever with integrated piezoelectric capacitor and proof-mass that incorporates a permanent magnet. When brought close to an AC current carrying wire, the magnet couples to the AC magnetic field from a wire, causing the cantilever to vibrate and generate power. The measured average power dissipated across an optimal resistive load was 1.5 μW. This was obtained by exciting the device into mechanical resonance using the electro-magnetic field from the 2 A source current. The measurements also reveal that the device has a nonlinear response that is due to a spring hardening mechanism.

Simulation by discrete mass modeling of offshore wind turbine system with DC link

This paper presents an integrated model for an offshore wind turbine taking into consideration a contribution for the marine wave and wind speed with perturbations influences on the power quality of current injected into the electric grid. The paper deals with the simulation of one floating offshore wind turbine equipped with a permanent magnet synchronous generator, and a two-level converter connected to an onshore electric grid. The use of discrete mass modeling is accessed in order to reveal by computing the total harmonic distortion on how the perturbations of the captured energy are attenuated at the electric grid injection point. Two torque actions are considered for the three-mass modeling, the aerodynamic on the flexible part and on the rigid part of the blades. Also, a torque due to the influence of marine waves in deep water is considered. Proportional integral fractional-order control supports the control strategy. A comparison between the drive train models is presented.

Blade pitch control malfunction simulation in a wind energy conversion system with MPC five-level converter

This paper is on a wind energy conversion system simulation of a transient analysis due to a blade pitch control malfunction. The aim of the transient analysis is the study of the behavior of a back-to-back multiple point clamped five-level full-power converter implemented in a wind energy conversion system equipped with a permanent magnet synchronous generator. An alternate current link connects the system to the grid. The drive train is modeled by a three-mass model in order to simulate the dynamic effect of the wind on the tower. The control strategy is based on fractional-order control. Unbalance voltages in the DC-link capacitors are lessen due to the control strategy, balancing the capacitor banks voltages by a selection of the output voltage vectors. Simulation studies are carried out to evaluate not only the system behavior, but also the quality of the energy injected into the electric grid.

Offshore Wind Energy Conversion System Connected to the Electric Grid: Modeling and Simulation

This paper is on modeling and simulation for an offshore wind system equipped with a semi-submersible floating platform, a wind turbine, a permanent magnet synchronous generator, a multiple point clamped four level or five level full-power converter, a submarine cable and a second order filter. The drive train is modeled by three mass model considering the resistant stiffness torque, structure and tower in deep water due to the moving surface elevation. The system control uses PWM by space vector modulation associated with sliding mode and proportional integral controllers. The electric energy is injected into the electric grid either by an alternated current link or by a direct current link. The model is intend to be a useful tool for unveil the behavior and performance of the offshore wind system, especially for the multiple point clamped full-power converter, under normal operation or under malfunctions.

HVDC Power Transmission Simulation for Offshore Wind System with Three-Level Converter

An integrated mathematical model for the simulation of an offshore wind system performance is presented in this paper. The mathematical model considers an offshore variable-speed turbine in deep water equipped with a permanent magnet synchronous generator using multiple point full-power clamped three-level converter, converting the energy of a variable frequency source in injected energy into the electric network with constant frequency, through a HVDC transmission submarine cable. The mathematical model for the drive train is a concentrate two mass model which incorporates the dynamic for the blades of the wind turbine, tower and generator due to the need to emulate the effects of the wind and the floating motion. Controller strategy considered is a proportional integral one. Also, pulse width modulation using space vector modulation supplemented with sliding mode is used for trigger the transistors of the converter. Finally, a case study is presented to access the system performance.

Design, production and testing of innovative key components of HEV/BEV powertrains

Through modelling activity, experimental campaigns, test bench and on-field validation, a complete powertrain for a BEV has been designed, assembled and used in a motorsport competition. The activity can be split in three main subjects, representing the three key components of an BEV vehicle. First of all a model of the entire powertrain has been developed in order to understand how the various design choices will influence the race lap-time. The data obtained was then used to design, build and test a first battery pack. After bench tests and track tests, it was understood that by using all the cell charac-teristics, without breaking the rules limitations, higher energy and power densities could have been achieved. An updated battery pack was then designed, produced and raced with at Motostudent 2018 re-sulting in a third place at debut. The second topic of this PhD was the design of novel inverter topologies. Three inverters have been de-signed, two of them using Gallium Nitride devices, a promising semiconductor technology that can achieve high switching speeds while maintaining low switching losses. High switching frequency is crucial to reduce the DC-Bus capacitor and then increase the power density of 3 phase inverters. The third in-verter uses classic Silicon devices but employs a ZVS (Zero Voltage Switching) topology. Despite the in-creased complexity of both the hardware and the control software, it can offer reduced switching losses by using conventional and established silicon mosfet technology. Finally, the mechanical parts of a three phase permanent magnet motor have been designed with the aim to employ it in UniBo Motorsport’s 2020 Formula Student car.

Power sharing e controllo modulare di macchine elettriche multi-trifase

La costante ricerca e lo sviluppo nel campo degli azionamenti e dei motori elettrici hanno portato ad una loro sempre maggiore applicazione ed utilizzo. Tuttavia, la crescente esigenza di sistemi ad alta potenza sempre più performanti da una parte ha evidenziato i limiti di certe soluzioni, dall’altra l’affermarsi di altre. In questi sistemi, infatti, la macchina elettrica trifase non rappresenta più l’unica soluzione possibile: negli ultimi anni si è assistito ad una sempre maggiore diffusione di macchine elettriche multifase. Grazie alle maggiori potenzialità che sono in grado di offrire, per quanto alcune di queste siano ancora sconosciute, risultano già essere una valida alternativa rispetto alla tradizionale controparte trifase. Sicuramente però, fra le varie architetture multifase, quelle multi-trifase (ovvero quelle con un numero di fasi multiplo di tre) rappresentano una soluzione particolarmente vantaggiosa in ambito industriale. Infatti, se impiegate all’interno di architetture multifase, la profonda conoscenza dei tradizionali sistemi trifase consente di ridurre i costi ed i tempi legati alla loro progettazione. In questo elaborato la macchina elettrica multi-trifase analizzata è una macchina sincrona esafase con rotore a magneti permanenti superficiali. Questa particolare tipologia di macchina elettrica può essere modellizzata attraverso due approcci completamente differenti: uno esafase ed uno doppio trifase. Queste possibilità hanno portato molti ricercatori alla ricerca della migliore strategia di controllo per questa macchina. L’obiettivo di questa tesi è di effettuare un’analisi comparativa tra tre diverse strategie di controllo applicate alla stessa macchina elettrica multi-trifase, analizzandone la risposta dinamica in diverse condizioni di funzionamento.

Axis control optimization: autotuning techniques and frequency response analysis of industrial mechatronic systems

In the field of industrial automation, there is an increasing need to use optimal control systems that have low tracking errors and low power and energy consumption. The motors we are dealing with are mainly Permanent Magnet Synchronous Motors (PMSMs), controlled by 3 different types of controllers: a position controller, a speed controller, and a current controller. In this thesis, therefore, we are going to act on the gains of the first two controllers by going to find, through the TwinCAT 3 software, what might be the best set of parameters. To do this, starting with the default parameters recommended by TwinCAT, two main methods were used and then compared: the method of Ziegler and Nichols, which is a tabular method, and advanced tuning, an auto-tuning software method of TwinCAT. Therefore, in order to analyse which set of parameters was the best,several experiments were performed for each case, using the Motion Control Function Blocks. Moreover, some machines, such as large robotic arms, have vibration problems. To analyse them in detail, it was necessary to use the Bode Plot tool, which, through Bode plots, highlights in which frequencies there are resonance and anti-resonance peaks. This tool also makes it easier to figure out which and where to apply filters to improve control.