Characterizing the physical and chemical properties of a vermicompost filter bed

Vermicompost filtration is a new on-site waste treatment system. Consequently, little is known about the filter medium properties. The aim of this preliminary study was to quantify physical and compositional properties of vermicompost filter beds that had been used to treat domestic solid organic waste and wastewater. This paper presents the trials performed on pilot-scale reactors filled with vermicompost from a full-scale vermicompost filtration system. Household solid organic waste and raw wastewater at the rate of 130 L/m(2)/d was applied to the reactor bed surface over a four-month period. It was found that fresh casts laid on the bed surface had a BOD of 1290 mg/g VS while casts buried to a depth of 10 cm had a BOD of 605 mg/g VS. Below this depth there was little further biodegradation of earthworm casts despite cast ages of up to five years. Solid material in the reactor accounted for only 7-10% of the reactor volume. The total voidage comprised of large free-draining pores, which accounted for 15-20% of the reactor volume and 60-70% micropores, able to hold up water against gravity. It was shown that water could flow through the medium micropores and macropores following a wastewater application. The wastewater flow characteristics were modeled by a two-region model based on the Richards Equation, an equation used to describe porous spatially heterogeneous materials.

A study of gas holdup properties of selected non-Newtonian simulants

The U.S. Department of Energy (DOE) needs a design basis to properly design a PJM and ventilation systems for the Waste Treatment Plant vessels. In order to meet DOE's needs for proper ventilation and PJM design technologies, Florida International University's Hemispheric Center for Environmental Technology (FIU-HCET) has studied the properties for gas holdup in selected non Newtonian fluids with physicochemical properties comparable to nuclear waste. The primary purpose of this research was to study the holdup properties of selected non - Newtonian simulants and quantify the level of gas holdup in selected simulants using continuous argon injection in five gallons vessel. Gas holdup tests involved the injection of gas bubbles in simulant waste in scaled prototypic vessels. The holdup was measured as a function of injection rate in the vessel. Tests were performed with both Laponite, Clay 12%, Clay 27% and Qard 13.5. This work showed that the percentage of holdup was about 3% for all simulants despite the significant differences in rheology.

Caracterização e separação física de placas de circuito impresso de computadores obsoletos

The unbridled consumption of electronic equipment associated with fast immersion of new technologies on the market leads to the accelerated growth of electronic waste. Such waste mostly contains printed circuit boards in its structure. Printed circuit boards have many metals, including heavy metals, being highly toxic. Electronic waste is discarded improperly and indiscriminately, usually without any previous treatment and with other municipal waste, contaminating the environment and causing serious problems to human health. Beyond these metals, there are also precious metals and high value-added basis, that can be recovered and recycled, reducing the exploration of natural resources. Thus, due to the high growth potential and reuse of these waste treatment processes, characterization and separation were applied to the printed circuit boards. The printed circuit boards were subjected to physical treatments such as dismantling, crushing, sizing separation, magnetic separation and chemical treatments such as pyrolysis and leaching. Through characterization process (pyrolysis and leaching) the proportions of the components of the granulometric range were determined: 46,08% of metals; 23,32% of polymers and 30,60% of ceramics. It was also observed by particle size separation that metal components tend to concentrate in coarse fractions, while polymeric and ceramic components in fine fractions. From the magnetic separation process was obtained 12,08% of magnetic material and 82,33% of non-magnetic material.

Size, blood organochlorine pesticide concentrations and biochemical indicators measured in hawksbill sea turtles (Eretmochelys imbricata) nesting at Punta Xen (Campeche, Mexico) in August 2010

The impact of environmental pollution on the homeostasis of sea turtles remains scarce, particularly in the southern Gulf of Mexico. As many municipalities do not rely on a waste treatment plant along the coastline of the Yucatan Peninsula, the vulnerability of these specimens could results enhanced. We searched for relationships between presence of organochlorine pesticides (OCP) and the level of several oxidative and pollutant stress indicators of the hawksbill sea turtle (Eretmochelys imbricata) during the egg-laying period 2010 at Punta Xen (Campeche, Mexico). Endosulfans, aldrin related (aldrin, endrin, dieldrin, endrin ketone, endrin aldehyde) and dichlorodiphenyldichloroethylene (DDT) families were detected in 17, 21 and 26 of the 30 sampled sea turtles, respectively. Significant correlation existed between the size of sea turtles with the concentration of methoxychlor, cholinesterase activity in plasma and heptachlors family, and catalase activity and hexachlorohexane family. Cholinesterase activity in washed erythrocytes and lipid peroxidation were positively correlated with glutathione reductase activity. Antioxidant enzyme actions seem adequate as no lipids damages were correlated with any OCPs. Future studies are necessary to evaluate the effect of OCPs on males of the area because of the significant detection of methoxychlor that target endocrine functioning and increase its concentration with size of the sea turtles.

Produção de CDR a partir de resíduos industriais: caso de estudo da Recivalongo

A produção de combustível derivado de resíduos (CDR) resultou de uma decisão política que permitiu a instalação em Portugal de um significativo conjunto de processos, cuja avaliação técnico-económica e ambiental pode já ser feita. Este trabalho faz uma avaliação técnica e ambiental da linha de produção de CDR da Recivalongo. A avaliação técnica consistiu na análise dos caudais de material que entraram na linha de produção, na quantidade de CDR produzido, contabilizando também os gastos de recursos da linha (energia e materiais auxiliares). A avaliação da qualidade de CDR produzido a partir do ensaio laboratorial representou também uma parte muito significativa do trabalho produzido. A avaliação ambiental foi efetuada com base na metodologia da Avaliação de Ciclo de Vida (ACV). Os resultados obtidos permitiram concluir que o processo da Recivalongo transforma 69% do material de entrada, recuperando 2% em metais ferrosos e rejeitando para aterro a restante fração de 29%. As análises efetuadas ao CDR mostraram que apresenta um PCI compreendido entre 17 e 20 MJ/kg; o teor em cloro está compreendido entre 0,2 e 0,8% Conclui-se que neste processo o parâmetro mais difícil de controlar é o teor em cloro no CDR, pois existe uma grande diversidade de resíduos com grandes quantidades de cloro na sua constituição e que por muitas vezes são difíceis de identificar e/ou separar na primeira fase do tratamento dos resíduos. Da análise ciclo de vida efetuada à produção de CDR pode-se afirmar que esta operação de gestão de resíduos apresenta uma mais-valia quando comparada com a deposição dos resíduos em aterro, não sendo a diferença entre destinos tão significativa quanto o esperado. Desta avaliação pode concluir-se que a instalação operou muito abaixo da sua capacidade, sendo esta considerada uma das melhores linhas de produção de CDR a nível nacional.

Procedimiento y dispositivo para el tratamiento integrado de residuos vegetales procedentes de explotaciones agrícolas y de las aguas residuales originadas

Procedimiento y dispositivo para el tratamiento integrado de residuos vegetales procedentes de explotaciones agrícolas y de las aguas residuales originadas. Procedimiento y dispositivo para el tratamiento de residuos vegetales en el que un volumen de residuos se somete a un proceso que integra las siguientes operaciones: (i) cortado mediante cizalla, (ii) homogeneizado mediante vibración, (iii) lavado con surfactantes en cilindro rotatorio, (iv) secado en cinta continua mediante chorro de aire caliente, y (v) secado opcional en tanque giratorio provisto de chorro de aire caliente, en caso de ser necesario reducir la humedad, originándose finalmente un residuo estable, de menor volumen que el inicial apto para uso industrial, y una corriente de aguas de lavado con una elevada concentración de pesticidas, microorganismos, surfactantes y partículas. La corriente de aguas de lavado se filtran y se llevan a un tanque-reactor que por tratamiento oxidativo con ozono y agua oxigenada mineraliza loscontaminantes presentes permitiendo su reutilización.

Generation of a business plan for a logistics service provider

The purpose of this Master’s Thesis was to study the suitability of transportation of liquid wastes to the portfolio of the case company. After the preliminary study the waste types were narrowed down to waste oil and oily waste from ports. The thesis was executed by generating a business plan. The qualitative research of this Master’s Thesis was executed as a case study by collecting information from multiple sources. The business plan was carried out by first familiarizing oneself with literature related to business planning which was then used as a base for the interview of the customer and interviews of the personnel of the case company. Additionally, internet sources and informal conversational interviews with the personnel of the case company were used and these interviews took place during the preliminary study and this thesis. The results of this thesis describe the requirements for the case company that must be met to be able to start operations. Import of waste oil fits perfectly to the portfolio of the case company and it doesn’t require any big investments. Success of the import of waste oil is affected by price of crude oil, exchange rate of ruble and legislation among others. Transportation of oily waste from ports, in turn, is not a core competence of the case company so more actions are required to start operating such as subcontracting with a waste management company.

Valorização de resíduos provenientes da atividade no setor avícola: aplicação do processo de compostagem

O setor avícola, como setor em constante crescimento está associado à produção de elevadas quantidades de resíduos sólidos orgânicos. A crescente taxa de produção de resíduos avícolas leva à necessidade de lhes dar um destino adequado podendo a valorização orgânica, nomeadamente a compostagem, ser uma opção. O presente estudo pretende dar um contributo para o projeto de uma unidade de compostagem numa empresa portuguesa do setor, com valorização dos resíduos produzidos pela mesma, avaliando o potencial de aplicação desta operação de tratamento de resíduos e a qualidade do produto final. Como primeiro passo foi realizada uma caracterização dos resíduos a utilizar de forma a perceber a sua possível influência no processo de degradação. Os ensaios de compostagem foram realizados à escala laboratorial, numa gama de temperatura de 50 a 55ᵒC, utilizando como substrato base uma mistura dos resíduos avícolas, de acordo com os seus quantitativos de produção. Vários potenciais agentes estruturantes foram também testados, como adição ao substrato. A monitorização do processo foi feita com base em análises das fases gasosa (gases de exaustão), sólida (substrato em decomposição) e líquida (lixiviado). A avaliação do processo foi ainda complementada com a caracterização dos produtos finais obtidos, os quais foram ainda sujeitos a testes de fitotoxicidade. Foram observados graus de conversão de matéria orgânica relativamente altos (40-50%), comprovando a aplicabilidade desta operação de tratamento de resíduos. Embora a diferença entre ensaios tenha sido pouco notória, a utilização de uma combinação de cama de aviário e mato destroçado e compostado aparenta ser ligeiramente mais eficiente, enquanto a utilização de casca de eucalipto produziu os piores resultados. Perdas de humidade e de azoto foram as duas situações mais críticas observadas para os vários ensaios, tendo influência tanto sobre o processo como sobre o produto final. Os compostos obtidos revelam baixa qualidade, exibindo valores elevados de pH e condutividade elétrica e elevadas concentrações de metais pesados, tais como cobre e zinco. Supõe-se que as características adversas verificadas estejam associadas à aplicação de quantidades demasiado elevadas de cinza nos substratos, levando à necessidade de redução deste material; estudos adicionais seriam necessários a fim de avaliar as possibilidades de ajuste das quantidades a utilizar, dos diferentes materiais, com o intuito de produzir um produto final com qualidade, respeitando os requisitos legais.

System innovation and life cycle thinking in packaging value chain: the circularity of plastics.

Compared to other, plastic materials have registered a strong acceleration in production and consumption during the last years. Despite the existence of waste management systems, plastic_based materials are still a pervasive presence in the environment, with negative consequences on marine ecosystem and human health. The recycling is still challenging due to the growing complexity of product design, the so-called overpackaging, the insufficient and inadequate recycling infrastructure, the weak market of recycled plastics and the high cost of waste treatment and disposal. The Circular economy package, the European Strategy for plastics in a circular economy and the recent European Green Deal include very ambitious programmes to rethink the entire plastic value chain. As regards packaging, all plastic packaging will have to be 100% recyclable (or reusable) and 55% recycled by 2030. Regions are consequently called upon to set up a robust plan able to fit the European objectives. It takes on greater importance in Emilia Romagna where the Packaging valley is located. This thesis supports the definition of a strategy aimed to establish an after-use plastics economy in the region. The PhD work has set the basis and the instruments to establish the so-called Circularity Strategy with the aim to turn about 92.000t of plastic waste into profitable secondary resources. System innovation, life cycle thinking and participative backcasting method have allowed to deeply analyse the current system, orientate the problem and explore sustainable solutions through a broad stakeholder participation. A material flow analysis, accompanied by a barrier analysis, has supported the identification of the gaps between the present situation and the 2030 scenario. Eco-design for and from recycling (and a mass _based recycling rate (based on the effective amount of plastic wastes turned into secondary plastics), valorized by a value_based indicator, are the key-points of the action plan.

Modelling of the kinetics of municipal solid waste composting in full-scale mechanical-biological treatment plants

A thesis submitted in fulfilment of the requirements for the Degree of Doctor of Philosophy in Sanitary Engineering in the Faculty of Sciences and Technology of the New University of Lisbon

A Tool for optimum design of Waste Water Treatment Plants under uncertainty

L’objectiu principal és presentar un nou prototipus d’eina per al disseny de les plantes de tractament d’aigües residuals utilitzant models mecànics dinàmics quantificant la incertesa

Treatment of ruptured abdominal aortic aneurysm, a permanent challenge or a waste of resources? Prediction of outcome using a multi-organ-dysfunction score.

OBJECTIVES: in a retrospective study, attempts have been made to identify individual organ-dysfunction risk profiles influencing the outcome after surgery for ruptured abdominal aortic aneurysms. METHODS: out of 235 patients undergoing graft replacement for abdominal aortic aneurysms, 57 (53 men, four women, mean age 72 years [s.d. 8.8]) were treated for ruptured aneurysms in a 3-year period. Forty-eight preoperative, 13 intraoperative and 34 postoperative variables were evaluated statistically. A simple multi-organ dysfunction (MOD) score was adopted. RESULTS: the perioperative mortality was 32%. Three patients died intraoperatively, four within 48 h and 11 died later. A significant influence for pre-existing risk factors was identified only for cardiovascular diseases. Multiple linear-regression analysis indicated that a haemoglobin <90 g/l, systolic blood pressure <80 mmHg and ECG signs of ischaemia at admission were highly significant risk factors. The cause of death for patients, who died more than 48 h postoperatively, was mainly MOD. All patients with a MOD score >/=4 died (n=7). These patients required 27% of the intensive-care unit (ICU) days of all patients and 72% of the ICU days of the non-survivors. CONCLUSION: patients with ruptured aortic aneurysms from treatment should not be excluded. However, a physiological scoring system after 48 h appears justifiable in order to decide on the appropriateness of continual ICU support.

Potential of energy and nutrient recovery from biodegradable waste by co-treatment in Lithuania

Biodegradable waste quantities in Lithuania and their potential for the co-treatment in renewable energy and organic fertilizer production are investigated. Two scenarios are formulated to study the differences of the amounts of obtainable energy and fertilizers between different ways of utilization. In the first scenario, only digestion is used, and in the second scenario, other materials than straw are digested, and straw and the solid fraction of sewage sludge digestate are combusted. As a result, the amounts of heat and electricity, as well as the fertilizer amounts in the counties are obtained for both scenarios. Based on this study, the share of renewable energy in Lithuania could be doubled by the co-treatment of different biodegradable materials.

Waste Water Treatment Using Low Cost Natural Adsorbents

Heavy metals are major toxic pollutants with severe health effects on humans. They are released into the environment from a variety of industrial activities. Cadmium, lead, zinc, chromium and copper are the most toxic metals of widespread use in industries such as tanning, electroplating, electronic equipment manufacturing and chemical processing plants. Heavy metals contribute to a variety of adverse health environmental effects due to their acute and chronic exposure through air, water and food chain. Conventional treatment methods of metal removal are often limited by their cost and ineffectiveness at low concentrations. Adsorption, the use of inactivated biomass as adsorbents offers an attractive potential alternative to their conventional methods. Mango peel and Alisma plantago aquatica are naturally occurring and abundant biomass can offer an economical solution for metal removal.The Cd(II), Pb(II), Zn(II), Cr(III) and Cu(II) adsorption by milled adsorbents of mango peel and Alisma plantago aquatica were evaluated in batches.

Supervisory systems in waste water treatment plants: sistematise their implementation

La implantació de Sistemes de Suport a la presa de Decisions (SSD) en Estacions Depuradores d'Aigües Residuals Urbanes (EDAR) facilita l'aplicació de tècniques més eficients basades en el coneixement per a la gestió del procés, assegurant la qualitat de l'aigua de sortida tot minimitzant el cost ambiental de la seva explotació. Els sistemes basats en el coneixement es caracteritzen per la seva capacitat de treballar amb dominis molt poc estructurats, i gran part de la informació rellevant de tipus qualitatiu i/o incerta. Precisament aquests són els trets característics que es poden trobar en els sistemes biològics de depuració, i en conseqüència en una EDAR. No obstant, l'elevada complexitat dels SSD fa molt costós el seu disseny, desenvolupament i aplicació en planta real, pel que resulta determinant la generació d'un protocol que faciliti la seva exportació a EDARs de tecnologia similar. L'objectiu del present treball de Tesi és precisament el desenvolupament d'un protocol que faciliti l'exportació sistemàtica de SSD i l'aprofitament del coneixement del procés prèviament adquirit. El treball es desenvolupa en base al cas d'estudi resultant de l'exportació a l'EDAR Montornès del prototipus original de SSD implementat a l'EDAR Granollers. Aquest SSD integra dos tipus de sistemes basats en el coneixement, concretament els sistemes basats en regles (els quals són programes informàtics que emulen el raonament humà i la seva capacitat de solucionar problemes utilitzant les mateixes fonts d'informació) i els sistemes de raonament basats en casos (els quals són programes informàtics basats en el coneixement que volen solucionar les situacions anormals que pateix la planta en el moment actual mitjançant el record de l'acció efectuada en una situació passada similar). El treball està estructurat en diferents capítols, en el primer dels quals, el lector s'introdueix en el món dels sistemes de suport a la decisió i en el domini de la depuració d'aigües. Seguidament es fixen els objectius i es descriuen els materials i mètodes utilitzats. A continuació es presenta el prototipus de SSD desenvolupat per la EDAR Granollers. Una vegada el prototipus ha estat presentat es descriu el primer protocol plantejat pel mateix autor de la Tesi en el seu Treball de Recerca. A continuació es presenten els resultats obtinguts en l'aplicació pràctica del protocol per generar un nou SSD, per una planta depuradora diferent, partint del prototipus. L'aplicació pràctica del protocol permet l'evolució del mateix cap a un millor pla d'exportació. Finalment, es pot concloure que el nou protocol redueix el temps necessari per realitzar el procés d'exportació, tot i que el nombre de passos necessaris ha augmentat, la qual cosa significa que el nou protocol és més sistemàtic.