Highly conductive and transparent ZnO thin film using Chemical Spray Pyrolysis technique: Effect of doping and deposition parameters

In the present work we report the preparation details studies on ZnO thin films. ZnO thin films are prepared using cost effective deposition technique viz., Chemical Spray Pyrolysis (CSP). The method is very effective for large area preparation of the ZnO thin film. A new post-deposition process could also be developed to avoid the adsorption of oxygen that usually occurs after the spraying process i.e., while cooling. Studies were done by changing the various deposition parameters for optimizing the properties of ZnO thin film. Moreover, different methods of doping using various elements are also tried to enhance the conductivity and transparency of the film to make these suitable for various optoelectronic applications.

Studies on polymer blends with special reference to NBR/PVC and CR/PVC blends

The study is undertaken on PVC blends because of their all-round importance-One of the most prominent needs of PVC in application end-use is permanent plasticizationlo. Butadiene-acrylonitrile rubber (NBR) has been utilized as permanent plasticizer for PVC since the 1940s for wire and cable insulation, food contact, and pondliners used for oil containment23'24. Also plasticized PVC has been added to vulcanizable nitrile rubber, to yield improved ozone, thermal ageing, and chemical resistance resulting in applications including fuel hose covers, gaskets, conveyor belt covers, and printing roll covers. This blend is miscible in the range of 23 to 45 per cent acrylonitrile content in the butadiene-acrylqnitrile copolymerzs. The first phase of the study was directed towards modification blends. These blends, in addition to the polymers, require a host of additives like curatives for the NBR phase and stabilizers for the PVC phase26of the existing PVC blends, especially NBR/PVC. The second phase of the study was directed towards the development of novel PVC based blends. Chloroprene rubber (polychloroprene) (CR) is structurally similar to PVC and hence is likely to form successful blends with PVC32.

Reliable and Damage-Free Estimation of Resistivity of ZnO Thin Films for Photovoltaic Applications Using Photoluminescence Technique

This work projects photoluminescence (PL) as an alternative technique to estimate the order of resistivity of zinc oxide (ZnO) thin films. ZnO thin films, deposited using chemical spray pyrolysis (CSP) by varying the deposition parameters like solvent, spray rate, pH of precursor, and so forth, have been used for this study. Variation in the deposition conditions has tremendous impact on the luminescence properties as well as resistivity. Two emissions could be recorded for all samples—the near band edge emission (NBE) at 380 nm and the deep level emission (DLE) at ∼500 nm which are competing in nature. It is observed that the ratio of intensities of DLE to NBE ( DLE/ NBE) can be reduced by controlling oxygen incorporation in the sample. - measurements indicate that restricting oxygen incorporation reduces resistivity considerably. Variation of DLE/ NBE and resistivity for samples prepared under different deposition conditions is similar in nature. DLE/ NBE was always less than resistivity by an order for all samples.Thus from PL measurements alone, the order of resistivity of the samples can be estimated.

Estabilidade e eficácia de fotoprotetores contendo filtros inorgânicos e quercetina

A exposição ao sol traz benefícios à saúde, no entanto, o excesso pode ocasionar danos cutâneos dentre os quais se destacam as neoplasias. A fotoproteção é um método para a prevenção dos efeitos danosos da radiação ultravioleta (UV) e a biodiversidade Brasileira é campo fértil para pesquisas nesta área. Dessa forma, os objetivos deste estudo envolveram o desenvolvimento de formulações fotoprotetoras contendo quercetina (composto bioativo) e filtros solares físicos (dióxido de titânio e óxido de zinco), com posterior caracterização das formulações e avaliação da sua estabilidade. As formulações contendo o composto bioativo, isolado ou em associação com os filtros físicos, possuíram valores de pH biocompatíveis com a pele,intervalo de viscosidade aparente entre 10550 e 23600 cP; fator de proteção solar (FPS) estimado entre 2.1 e 22.5; e amplo espectro de proteção, com comprimentos de onda crítico acima de 379 nm. Constatou-se que não foi adequado utilizar a quercetina associada aos filtros solares físicos devido às interações negativas que ocorreram entre o composto e os metais, somente identificadas ao longo do estudo de estabilidade. No entanto, em função da eficácia estimada in vitro apresentada pelo flavonoide, seu uso ainda pode ser explorado como substituto alternativo aos filtros solares clássicos.

Photocatalytic degradation of humic acid in saline waters part 2. Effects of various photocatalytic materials

The present study explores for the first time, the effectiveness of photocatalytic oxidation of. humic acid (HA) in the increasingly important highly saline water. TiO2 (Degussa P25), TiO2 (Anatase), TiO2 (Rutile), TiO2 (Mesoporous) and ZnO dispersions were used as catalysts employing a medium pressure mercury lamp. The effect of platinum loading on P25 and zinc oxide was also investigated. The zinc oxide with 0.3% platinum loading was the most efficient catalyst. The preferred medium for the degradation of HA using ZnO is alkaline, whereas for TiO2 it is acidic. In addition, a comparative study of HA decomposition in artificial seawater (ASW) and natural seawater (NSW) is reported, and the surface areas and band gaps of the catalysts employed were also determined. A spectrophotometric method was used to estimate the extent of degradation of HA. (C) 2003 Elsevier Science B.V. All rights reserved.

Direct pulp capping with a self-etching adhesive system: Histopathologic evaluation in dogs` teeth

Objective. This study evaluated histopathologically the response of pulp and periradicular tissues after pulp capping with an all-in-one self-etching adhesive system in dogs` teeth. Study design. Forty teeth of 4 dogs were assigned to 3 groups according to the pulp capping material: G1 (n = 20): self-etching adhesive system; G2 (n = 10): Ca(OH)(2); G3 (n = 10): zinc oxide-eugenol. The animals were killed 7 and 70 days after pulp capping. The pieces containing the pulp-capped teeth were removed and processed for histologic analysis. Results. At 7 days, no dentin bridge formation was observed; G1 and G3 exhibited inflammatory pulpal alterations, whereas G2 presented only mild inflammatory infiltrate in the pulp tissue adjacent to the capping material, the remainder being intact. At 70 days, no specimen in G1 or G3 presented dentin bridge formation. The remaining pulp tissue exhibited severe inflammatory alterations and areas of necrosis. In G2, all specimens showed dentin bridge formation and absence of inflammation and mineralized tissue resorption. No bacteria were identified using Brown and Brenn staining techniques in all 3 groups at any observation period. Conclusion. According to the conditions of this study, direct pulp capping with the self-etching adhesive system did not allow pulp tissue repair and failed histopathologically in 100% of the cases. (Oral Surg Oral Med Oral Pathol Oral Radiol Endod 2009; 108: e34-e40)

Biomechanical effects of environmental and engineered particles on human airway smooth muscle cells

The past decade has seen significant increases in combustion-generated ambient particles, which contain a nanosized fraction (less than 100 nm), and even greater increases have occurred in engineered nanoparticles (NPs) propelled by the booming nanotechnology industry. Although inhalation of these particulates has become a public health concern, human health effects and mechanisms of action for NPs are not well understood. Focusing on the human airway smooth muscle cell, here we show that the cellular mechanical function is altered by particulate exposure in a manner that is dependent upon particle material, size and dose. We used Alamar Blue assay to measure cell viability and optical magnetic twisting cytometry to measure cell stiffness and agonist-induced contractility. The eight particle species fell into four categories, based on their respective effect on cell viability and on mechanical function. Cell viability was impaired and cell contractility was decreased by (i) zinc oxide (40-100 nm and less than 44 mu m) and copper(II) oxide (less than 50 nm); cell contractility was decreased by (ii) fluorescent polystyrene spheres (40 nm), increased by (iii) welding fumes and unchanged by (iv) diesel exhaust particles, titanium dioxide (25 nm) and copper(II) oxide (less than 5 mu m), although in none of these cases was cell viability impaired. Treatment with hydrogen peroxide up to 500 mu M did not alter viability or cell mechanics, suggesting that the particle effects are unlikely to be mediated by particle-generated reactive oxygen species. Our results highlight the susceptibility of cellular mechanical function to particulate exposures and suggest that direct exposure of the airway smooth muscle cells to particulates may initiate or aggravate respiratory diseases.

Zn(0.97)M(0.03)O (M = Co, Fe, and V) pigments: thermal, structural, and optical characterization

Zinc oxide is a widely used white inorganic pigment. Transition metal ions are used as chromophores and originate the ceramic pigments group. In this context, ZnO particles doped with Co, Fe, and V were synthesized by the polymeric precursors method, Pechini method. Differential scanning calorimetry (DSC) and thermogravimetry (TG) techniques were used to accurately characterize the distinct thermal events occurring during synthesis. The TG and DSC results revealed a series of decomposition temperatures due to different exothermal events, which were identified as H(2)O elimination, organic compounds degradation and phase formation. The samples were structurally characterized by X-Ray diffractometry revealing the formation of single phase, corresponding to the crystalline matrix of ZnO. The samples were optically characterized by diffuse reflectance measurements and colorimetric coordinates L*, a*, b* were calculated for the pigment powders. The pigment powders presented a variety of colors ranging from white (ZnO), green (Zn(0.97)Co(0.03)O), yellow (Zn(0.97)Fe(0.03)O), and beige (Zn(0.97)V(0.03)O).

CuO and CuO-ZnO catalysts supported on CeO(2) and CeO(2)-LaO(3) for low temperature water-gas shift reaction

This paper describes an investigation on CuO and CuO-ZnO catalysts supported on CeO(2) and CeO(2)-La(2)O(3) oxides, which were designed for the low temperature water-gas shift reaction (WGSR). Bulk catalysts were prepared by co-precipitation of metal nitrates and characterized by energy-dispersive spectroscopy (EDS), X-ray diffraction (XRD), surface area (by the BET method), X-ray photoelectron spectroscopy (XPS), and in situ X-ray absorption near edge structure (XANES). The catalysts` activities were tested in the forward WGSR, and the CuO/CeO(2) catalyst presented the best catalytic performance. The reasons for this are twofold: (1) the presence of Zn inhibits the interaction between Cu and Ce ions, and (2) lanthanum oxide forms a solid solution with cerium oxide, which will cause a decrease in the surface area of the catalysts. Also the CuO/CeO(2) catalyst presented the highest Cu content on the surface, which could influence its catalytic behavior. Additionally, the Cu and Cu(1+) species could influence the catalytic activity via a reduction-oxidation mechanism, corroborating to the best catalytic performance of the Cu/Ce catalyst. (c) 2010 Elsevier B.V. All rights reserved.

Efeito de preparações de produtos naturais (cravo da índia e tomate) e de um produto sintético na marcação de constituintes sangüineos com tecnécio-99m e na morfologia de hemácias isoladas de sangue de ratos wistar

There are strong interests in the evaluation of the biological effects of natural and synthetic products. Blood constituents labeled with technetium-99m (99mTc) are used in nuclear medicine. The aim of this work was to study the effects of Clove (Caryophyllus aromaticas L.) and OZE (preparation used in the Health Sciences) on the labeling blood constituents with 99mTc and on the morphologic red blood cells (RBC) and the action of an extract of tomato (TO) on the labeling of blood constituents Blood samples were incubated with clove or OZE or TO, stannous chloride and 99mTc. Plasma (P), blood cells (BC), insoluble fractions (IF) of plasma and blood cells were separated. The radioactivity was counted and percentage of radioactivity (%ATI) to each blood fraction was calculated. The shape and morphometric parameter (perimeter/area ratio) were evaluated in the studies with clove and OZE. Clove extract and OZE altered significantly (p<0.05) the %ATI of blood constituents and the shape of red blood cells. However, clove extract not altered the red blood cells perimeter/area ratio. The tomato extract used at the highest concentrations reduced significantly (p<0.05) the %ATI in IF-P, although this extract did not modify the radiolabeling on BC, neither the radioactivity fixation on IFBC. The results indicate that these chemical compounds would have oxidative/chelating actions

Desenvolvimento de microemulsões contendo fotoprotetores inorgânicos nanoparticulador

The inorganic actives, represented mainly by microfine zinc oxide and titanium dioxide, have shown great potential to protect against large UV spectrum. The aim of this study is the development, characterization and analysis of stability in the short term of microemulsions containing inorganic fotoprotection agents. The microemulsions identified by the phases diagram containing the metallic oxides were produced by two different methods and subjected to the centrifugation test and thermal stress cycles, and subsequently characterized by macroscopic evaluation, test dilution, electrical conductivity, pH, particle size, and zeta potential. This study highlights the influence of the metal oxides addition in the structure and distribution of micelles in the microemulsions

Avaliação da interação de nutrientes na aplicação de zinco em sementes de arroz

The efficient fertilizer use contend micronutrient depends, also, of the interactions that occur with some nutrients. The objective was to study the interaction of zinc with the excessively nutrient ones in function of the application of different doses and sources of Zn saw seed in the culture of the rice. The experiment was carried through in conditions of vegetation house, in the FCAV/Unesp. The used experimental delineation was entirely cazualized, with three repetitions. The treatments had been five doses: 0; 1,0; 2,0; 4,0 and 8,0 g of Zn for kg of seed; e two zinc sources; sulphate of zinc (22% of Zn) and zinc oxide (50% of Zn). The experimental unit was a translucent polyethylene tray, filled with 5 washed thick sand, where 50 seeds of rice had been sown (to var. Caiapo). To the 30 days after the sowing, effected the cut of the plants, separating them in aerial part and roots. From the results of the dry substance and text of nutrients of the aerial part and root of the rice, the accumulation of the nutrients in the respective agencies of the plants was calculated. Becoming fullfilled it variance analysis and the when necessary unfoldings. It had effect of the interactions in distinguishing way between root and aerial part of rice, with regard to the doses and sources.

Concentração foliar de manganês e zinco em laranjeiras adubadas com óxidos e carbonatos via foliar

Dentre os micronutrientes, o Zn e o Mn limitam a produção dos citros, no Brasil. A aplicação foliar tem sido a forma tradicional de fornecimento, contudo, a eficiência desta adubação depende de uma série de fatores, entre eles o tipo de fertilizante. Foram realizados dois experimentos em pomar com laranjeiras Pêra, enxertadas em limão cravo, com sete anos de idade, em Botucatu, SP. No primeiro experimento foram avaliadas três fontes de Mn via foliar: carbonato de manganês A, carbonato de manganês B e sulfato manganoso, em duas doses para cada fertilizante, correspondente a 250 e 500 g ha-1 de Mn, mais o controle, pulverizado somente com água. No segundo experimento foram testadas três fontes de Zn para aplicação foliar: óxido de zinco A, óxido de zinco B e sulfato de zinco, em duas doses para cada fertilizante, correspondente a 375 e 750 g ha-1 de Zn, mais o controle. As amostragens de folhas foram realizadas mensalmente, iniciando aos 30 dias após aplicação dos tratamentos. A aplicação foliar com carbonato de manganês B, na dose de 500 g ha-1 Mn, e com óxido de zinco B, na dose de 750 g ha-1, proporcionaram, respectivamente, níveis nutricionais adequados de Mn e Zn nas folhas de laranjeira. Na ausência de chuvas, os teores adequados de Mn e Zn no solo, não permitem suprir satisfatoriamente as laranjeiras Pêra enxertadas em limoeiro cravo.

ZnO-TiO2 composite formed by mixed oxides via polyol

Among the researches on preparation and test of nanostructured materials, titanium dioxide and zinc oxide have been the most frequent studied oxides. In order to extend their properties, composites have been prepared using three different methods: Polyol Method, Sol-gel Process and a combination of the two processes (hybrid process). Recent research showed best properties in composite materials than in pure oxides. In this work is presented the preparation and the structural characterization of ZnO-TiO2 composite nanostructures to be tested for their performance in electrocatalysis and in further trial on photovoltaic cells.

Síntese e caracterização de óxidos de zinco e de magnésio suportados em A1SBA-15 para produção de biodiesel

To overcome the challenge of meeting growing energy demand in a sustainable way, biodiesel has shown very promising as alternative energy can replace fossil fuels, even partially. Industrially, the biodiesel is produced by homogeneous transesterification reaction of vegetable oils in the presence of basic species used as catalysts. However, this process is the need for purification of the esters obtained and the removal of glycerin formed after the reaction. This context, the alternative catalysts have that can improve the process of biodiesel production, aiming to reduce costs and facilitate its production. In this study, the AlSBA-15 support with Si / Al ratio = 50 was synthesized, as like as the heterogeneous catalysts of zinc oxide and magnesium supported on mesoporous AlSBA-15 silica, in the concentrations of 5, 10, 15 and 30 %, relative to the support. The textural properties and structural characterization of catalysts and supports were determined by techniques: X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) coupled to the chemical analyzer, adsorption / desorption of N2, thermal analysis (TG / DTG), absorption spectroscopy in the infrared (FTIR) and X-ray photoelectron spectroscopy (XPS). Characterization results indicated that the support AlSBA-15 retained the hexagonal ordered after the incorporation of zinc oxide and magnesium oxide in the holder. For heterogeneous catalysts, ZnO-AlSBA-15, that was observed the presence of zinc oxide nanoparticles dispersed in the surface and interior channels of the mesoporous and microporous support. The catalytic activity was evaluated by the transesterification reaction of sunflower oil via methylic route, and some reaction parameters were optimized with the most active catalyst in biodiesel production by sunflower oil. For the series of heterogeneous catalysts, the sample with 30 % ZnO supported on AlSBA-15 showed a better conversion of triglyceride to methyl esters, about 95.41 % of reaction conditions: temperature 175 °C, with molar ratio of 42:1, stirring at 200 rpm and under a pressure of 14 bar for 6 h. The catalyst MgO-AlSBA-15 showed no catalytic activity in the studied reactions