Análise dos resultados do ensaio CBR realizado em condições variadas de umidade pós-compactação

O objetivo deste trabalho é avaliar a influência da variação do teor de umidade no valor do índice de suporte CBR de uma brita estabilizada granulometricamente e de seis solos coletados em rodovias do interior do Estado de São Paulo. Os seis solos estudados foram divididos em três pares, com curvas granulométricas próximas, mesma classificação HRB e USCS, sendo cada par formado por um solo de comportamento laterítico e um solo de comportamento não-laterítico. Os corpos-de-prova foram moldados na umidade ótima e massa específica seca máxima obtidos com os resultados do ensaio de Proctor normal. Os materiais foram analisados sob quatro condições de umidade: sem imersão, após alcançar metade da umidade de estabilização, após quatro e oito dias de imersão. Observou-se a distribuição da umidade interna dos corpos-de-prova para cada uma das situações. Foi analisada a influência do envelhecimento dos materiais solto e compactado por quatro dias e sem imersão, nos resultados dos ensaios de CBR. Com os resultados pôde-se correlacionar a influência da granulometria e da gênese dos materiais nos resultados dos ensaios de índice de suporte CBR nas diversas condições de umidade avaliadas.

Influência do método de lavagem nas características de carvões antracitoso e betuminoso utilizados em meio filtrante

Teve como objetivo verificar e comparar a alteração das características do carvão antracitoso e do carvão betuminoso utilizados em meio filtrante, devido ao efeito abrasivo causado entre os grãos decorrentes de lavagens exclusivamente com água e lavagens independentes com ar e água. Foram estudados dois tipos de carvão antracitoso e um tipo de carvão betuminoso, para os quais foram determinadas suas características químicas e físicas. Os ensaios foram realizados em uma instalação ao piloto montada na escola de engenharia de São Carlos-EESC, USP, na qual foram feitas simulações de lavagens admitindo-se uma lavagem diária durante um ano para cada método, de modo intermitente, em que o meio granular era compactado ao final de cada lavagem, e continuo, sem compactação do meio granular. A velocidade ascensional utilizada para cada simulação de lavagem foi de 0,9 m/min, promovendo expansão no meio granular de 35 a 40%. A taxa de ar utilizada para as simulações de lavagens com aplicação de ar foi de 15 l/sm2. Após o término das 365 lavagens, foram determinados os valores médios do coeficiente de esfericidade e da porosidade do meio granular estratificado e construída a curva de distribuição granulométrica das amostras utilizadas nos ensaios. Conclui-se que o carvão betuminoso apresentou comportamento semelhante ao dos carvões antracitosos e que a metodologia de lavagem continua produz praticamente o mesmo efeito abrasivo comparada a de lavagem intermitente.

Utilização do resíduo grosso do beneficiamento da scheelita em aplicações rodoviárias

Mining is an activity of great economic and social value, assisting in the development of the country. However, it can be extremely harmful to the environment if no proper waste management study exists as mitigation measure its effects. Sample some of these harmful effects are pollution: water, through the seepage of waste into the groundwater; soil; of fauna and flora; sound (due to the noise of machines); visual from the residue stored in the open, changing the local landscape; and air. One way to mitigate environmental impacts caused by mining is the proper management of their waste through their use on highways. To that end, this paper proposes to give an appropriate destination to grit coming from the beneficiation of scheelite, due to mining activity from mining group Tomaz Salustino in Brejuí mine, located in the city of Currais Novos in the state of Rio Grande do Norte. This work was developed in four stages. The first comprised the chemical and mineralogical tests, DRX and FRX in which they sought to discover the composition of the material studied. The next step involved the physical characteristics of the waste by means of specific tests and grinding the solid mass, LL and LP. The third stage included the specific tests applied to the pavement, with the compaction test and test Index Support California. Finally, the fourth stage was the mechanical characterization, represented by direct shear tests, both in the flooded condition and not in flooded condition. The technical feasibility of using the modified energie compacted in layers of subbase power has been verified. In normal and intermediate energies is feasible to use less noble as layers as the subgrade. The incorporation of the waste in layers of road pavements provide an alternative to conventionally used in paving aggregates, providing a proper disposal of tailings from scheelite, as well as environmental preservation

Caracterização de resíduos oriundos do beneficiamento do minério de ferro para uso em pavimentação

Mining in Brazil has a key role in economic and social development, contributing directly to improve the lives of the population. However, the mining activity even if done responsibly and with a proper study of waste management to reduce the impact of its effects, may cause harmful damage to the environment. Other forms of pollution are also caused due to mining activity. The visual pollution caused by the waste storage at open sky, in addition to the noise pollution caused by the excessive noise of the machines both in the extraction of ore, as in processing. An alternative way to lessen the environmental impacts caused by mining is the use of waste in layers that will compose the pavements along the highways. Thus, this work sets out to give a proper disposal of the wastes from the processing of iron ore, resulting from the mining activity of the group of mining Mhag Services and Mining S/A, in the mine of Bonito, located in Jucurutu, a town in the state of Rio Grande do Norte. The residues of the iron ore were stabilized with a granular soil from the city of Macaiba, also in the state of Rio Grande do Norte, which is being used in the duplication of the BR-304 referring to the entitled passage of Reta Tabajara. The present work was developed in three stages, being the first one divided by the chemical and mineralogical tests, by the tests of physical characterization and by the tests of paving for the residues of the iron ore. The second stage corresponds to the same tests being performed for granular soil. The third stage includes the essays abovementioned for three different mixtures of iron ore waste and granular soil, being they: 15% of iron-ore waste and 85% of granular soil, 25% of iron-ore waste and 75% of granular soil, 50% of iron-ore waste and 50% of granular soil. The technical feasibility of using waste from the iron ore beneficiation was checked, compressed in the intermediate energy and modified for use in base layers, sub-base, reinforcement subgrade and subgrade. The incorporation of the residues originating from the improvement of the iron ore in highways will provide an alternative to the use of aggregate conventionally used in the paving, besides preserving the environment.

Avaliação da compactação do solo no crescimento inicial de espécies florestais da caatinga

Despite the importance of the study of roots, little is known about the negative effects of soil compaction in the development of the Caatinga forest species. In this sense, the objective was to evaluate the initial growth of Mimosa caesalpiniifolia, Tabebuia caraiba and Erythina velutina in soil under varying levels of compression. The experiment was conducted in a greenhouse located at the Academic Unit Specialized in Agricultural Sciences, UFRN. To perform the experiment, was used Oxisoil of sandy loam texture, from forest trial Area Agricultural School of Jundiaí (EAJ) of the municipality of Macaíba-RN, in an experimental unit consisting of three overlapping PVC rings, 10 cm in diameter and 25 cm in height, with a central ring which has undergone compression. The experimental design was a randomized block with six replications, being tested four levels of soil compaction (1.35; 1.45; 1.60 and 1.80 kg.dm-³), evaluating the following variables: diameter, height, number of leaves, dry weight of shoot and root system in each layer of the vessels. Overall, the species M. caesalpiniifolia, T. caraiba and E. velutina had initial growth favored by treatment consists of uncompressed soil. The M. caesalpiniifolia and T. caraiba species proved relatively resistant to compaction of the soil does not undergo any significant reduction in root growth density equal to or less than 1.60 kg.dm-³, whereas E. velutina proved susceptible effects of soil compaction, with significant changes in root growth under soil densities equal to or greater than 1.45 kg.dm-³. Increased soil compaction caused the impediment to the expansion of taproot inside the experimental units, promoting the accumulation of roots in the upper layers of the soil for the studied species. The subsoil physical impediment changed the initial aerial growth of M. caesalpiniifolia and E. velutina, but did not influence the growth of air T. caraiba seedlings the tested compression levels.

Análise de microestrutura e de características geotécnicas de misturas de resíduo de polimento de porcelanato e solo

Brazil is a country in development, rich in natural resources. In order to grow sustainably, it is necessary to Brazil to preserve its environment, which is an expressive challenge, especially to industries, such as those producing ceramic materials. This study was developed using Porcelain Tile Polishing Residue (RPP) in blends with soil to build compacted fills. This residue is a slurry generated during the polishing process of porcelain tiles and contains powdery material from the polished tile, the abrasives used during the process and cooling water. The RPP was collected from a private company located in Conde/PB and it was mixed with a sandy-clayey soil, to build the fills. Laboratorial tests were conducted with pure soil, pure RPP and blends in proportions of 5%, 10%, 15% and 20% of RPP in addition to the dry mass of pure soil. The Chemical and Physical Characterization tests performed were: specific solid weight, grain size distribution, laser analysis of grain size distribution, Atterberg limits, X ray fluorescence, X ray diffraction, scanning electron microscopy and soil compaction,. The materials and blends were also compacted and direct shear tests and plate load tests were performed. Plate load tests were conducted using a circular plate with 30 cm diameter, on specimens of pure soil and 5% blend, compacted in a metallic box inside the Soil Mechanics Laboratory of the Federal University of Rio Grande do Norte, Brazil. Both mechanical tests performed were conducted under inundated conditions, willing to reduce the influence of soil suction. An evaluation of the results of the tests performed shows that RPP is a fine material, with grain size distribution smaller than 0,015mm, composed mainly of silica and alumina, and particles in angular shape. The soil was characterized as a clayey sand, geologically known as a lateritic soil, with high percentages of alumina and iron oxide, and particles with rounded shape. Both the Soil and the blends presented low plasticity, while the residue showed a medium plasticity. Direct shear tests showed that the addition of RPP did not cause major changes into blends’ friction angle data, however, it was possible to note that, for the proportions studied, that is a tendency of obtain lower shear stresses for higher percentages of RPP in the blends. Both pure soil and 5% mixture showed a punching disruption for the Plate load test. For this same test, the allowable stress for 5% mixture was 44% higher than the pure soil, and smaller vertical settlement results for all stresses.

Análise de microestrutura e de características geotécnicas de misturas de resíduo de polimento de porcelanato e solo

Brazil is a country in development, rich in natural resources. In order to grow sustainably, it is necessary to Brazil to preserve its environment, which is an expressive challenge, especially to industries, such as those producing ceramic materials. This study was developed using Porcelain Tile Polishing Residue (RPP) in blends with soil to build compacted fills. This residue is a slurry generated during the polishing process of porcelain tiles and contains powdery material from the polished tile, the abrasives used during the process and cooling water. The RPP was collected from a private company located in Conde/PB and it was mixed with a sandy-clayey soil, to build the fills. Laboratorial tests were conducted with pure soil, pure RPP and blends in proportions of 5%, 10%, 15% and 20% of RPP in addition to the dry mass of pure soil. The Chemical and Physical Characterization tests performed were: specific solid weight, grain size distribution, laser analysis of grain size distribution, Atterberg limits, X ray fluorescence, X ray diffraction, scanning electron microscopy and soil compaction,. The materials and blends were also compacted and direct shear tests and plate load tests were performed. Plate load tests were conducted using a circular plate with 30 cm diameter, on specimens of pure soil and 5% blend, compacted in a metallic box inside the Soil Mechanics Laboratory of the Federal University of Rio Grande do Norte, Brazil. Both mechanical tests performed were conducted under inundated conditions, willing to reduce the influence of soil suction. An evaluation of the results of the tests performed shows that RPP is a fine material, with grain size distribution smaller than 0,015mm, composed mainly of silica and alumina, and particles in angular shape. The soil was characterized as a clayey sand, geologically known as a lateritic soil, with high percentages of alumina and iron oxide, and particles with rounded shape. Both the Soil and the blends presented low plasticity, while the residue showed a medium plasticity. Direct shear tests showed that the addition of RPP did not cause major changes into blends’ friction angle data, however, it was possible to note that, for the proportions studied, that is a tendency of obtain lower shear stresses for higher percentages of RPP in the blends. Both pure soil and 5% mixture showed a punching disruption for the Plate load test. For this same test, the allowable stress for 5% mixture was 44% higher than the pure soil, and smaller vertical settlement results for all stresses.

Estudo da sinterização e oxidação anódica na produção de um capacitor eletrolítico de nióbio

It seeks to find an alternative to the current tantalum electrolytic capacitors in the market due to its high cost. Niobium is a potential replacement for be lighter and cheaper than tantalum. They belong to the same table group periodically and thus exhibit several physical and chemical properties similar. Niobium is used in many technologically important applications, and Brazil has the largest reserves, around 96%. These electrolytic capacitors have high specific capacitance, so they can store high energy in small volumes compared to other types of capacitors. This is the main attraction of this type of capacitor because is growing demand in the production of capacitors with capacitance specifies increasingly high, this because of the miniaturization of various devices such as GPS devices, televisions, computers, phones and many others. The production route of the capacitor was made by powder metallurgy. The initial niobium poder was first characterized by XRD, SEM and laser particle size to then be sieved into particle size 400mesh. The powder was then compacted at pressure of 150MPa and sintered at 1400, 1450 and 1500°C using two sintering time 30 and 60min. Sintering is an important part of the process as it affects properties as porosity and surface cleaning of the samples, which greatly affected the quality of the capacitor. After sintering the samples were underwent a process of anodic oxidation (anodizing), which created a thin film of niobium pentoxide over the whole surface of the sample, this film is the dielectric capacitor. The anodizing process variables influenced a lot in film formation and consequently the capacitor. The samples were characterized by electrical measurements of capacitance, loss factor and ESR (equivalent series resistance). The sintering has affected the porosity and in turn the specific area of the samples. The capacitor area is directly related to the capacitance, that is, the higher the specific area is the capacitance. Higher sintering temperatures decrease the surface area but eliminate as many impurities. The best results were obtained at a temperature of 1400°C with 60 minutes. The most interesting results were compared with the specific capacitance and ESR for all samples.

Estudo da sinterização e oxidação anódica na produção de um capacitor eletrolítico de nióbio

It seeks to find an alternative to the current tantalum electrolytic capacitors in the market due to its high cost. Niobium is a potential replacement for be lighter and cheaper than tantalum. They belong to the same table group periodically and thus exhibit several physical and chemical properties similar. Niobium is used in many technologically important applications, and Brazil has the largest reserves, around 96%. These electrolytic capacitors have high specific capacitance, so they can store high energy in small volumes compared to other types of capacitors. This is the main attraction of this type of capacitor because is growing demand in the production of capacitors with capacitance specifies increasingly high, this because of the miniaturization of various devices such as GPS devices, televisions, computers, phones and many others. The production route of the capacitor was made by powder metallurgy. The initial niobium poder was first characterized by XRD, SEM and laser particle size to then be sieved into particle size 400mesh. The powder was then compacted at pressure of 150MPa and sintered at 1400, 1450 and 1500°C using two sintering time 30 and 60min. Sintering is an important part of the process as it affects properties as porosity and surface cleaning of the samples, which greatly affected the quality of the capacitor. After sintering the samples were underwent a process of anodic oxidation (anodizing), which created a thin film of niobium pentoxide over the whole surface of the sample, this film is the dielectric capacitor. The anodizing process variables influenced a lot in film formation and consequently the capacitor. The samples were characterized by electrical measurements of capacitance, loss factor and ESR (equivalent series resistance). The sintering has affected the porosity and in turn the specific area of the samples. The capacitor area is directly related to the capacitance, that is, the higher the specific area is the capacitance. Higher sintering temperatures decrease the surface area but eliminate as many impurities. The best results were obtained at a temperature of 1400°C with 60 minutes. The most interesting results were compared with the specific capacitance and ESR for all samples.

Situación nutricional y antioxidante de un colectivo de escolares españoles. Diferencias en función de la capacidad antioxidante de su dieta y de su composición corporal

La etapa infantil tiene una gran importancia desde el punto de vista nutricional, para el presente y futuro de los individuos. La alimentación equilibrada desempeña un papel fundamental en el crecimiento y desarrollo del niño, permitiendo mantener un estado de salud óptimo y mejorando su calidad de vida. Además, en la edad infantil se establecen gran parte de los hábitos y estilos de vida que persistirán a lo largo de toda la vida, entre ellos se establecen y conforman los hábitos alimentarios y las bases de la educación nutricional. En un metabolismo aeróbico, como el que caracteriza al cuerpo humano, se precisa del oxígeno para la mayoría de los procesos biológicos cuyo fin último es obtener energía, es decir, se produce la oxidación de los diferentes sustratos para obtener dicha energía a través de diferentes rutas metabólicas. Esta utilización de oxígeno en los procesos metabólicos, implica inevitablemente la formación de especies reactivas de oxígeno (ERO) o radicales libres, que favorecen los procesos de oxidación. Para compensar estos procesos, existen en el cuerpo humano una serie de sistemas de protección antioxidante que permiten la eliminación o transformación de las ERO en moléculas estables. Los sistemas biológicos están, por lo tanto, en un estado de equilibrio entre sustancias prooxidantes y su capacidad antioxidante. El desequilibrio a favor de la acción prooxidante es lo que se conoce como "estrés oxidativo", que puede conducir al daño celular y tisular, y finalmente al desarrollo de diferentes enfermedades: cáncer, arteriosclerosis, infarto de miocardio, procesos de isquemia/reperfusión, diabetes mellitus, asfixia neonatal, enfermedades inflamatorias, trastornos del sistema nervioso central, envejecimiento, ... Dentro de la alimentación encontramos nutrientes que median en este equilibrio oxidante-antioxidante, habiendo nutrientes que participan en el sistema de defensa antioxidante (vitamina C y E, carotenoides, flavonoides, melanoidinas, selenio, zinc..) y también sustancias que pueden actuar como prooxidantes (exceso de lípidos, proteínas, hierro o cobre)...

Diagnóstico de enfermagem risco de quedas em pacientes com angina instável

O risco de quedas pode ser reconhecido como fenômeno ou diagnóstico de enfermagem. Pesquisas relacionam diretamente isquemias miocárdicas, como a angina instável e o risco de cair. Objetivou-se analisar o diagnóstico de enfermagem Risco de quedas na ocorrência de angina instável por um estudo transversal realizado em 57 indivíduos internados em um hospitalescola, mediante exame físico e formulário. Para o tratamento estatístico foram utilizados teste qui-quadrado, teste exato de Fisher, Mann-Whitney, teste-t e Coefi ciente Phi (p<0,05). O Risco de quedas foi o diagnóstico de enfermagem mais prevalente (87,71%), sobretudo em homens, mais velhos, com menos anos de estudo e renda inferior. Presença da angina instável, hipertensão arterial, medicação anti-hipertensiva, doença vascular, difi culdades visuais e insônia apresentaram associação com o diagnóstico de enfermagem Risco de quedas. Conclui-se que é imprescindível o desenvolvimento de parâmetros claros e objetivos à mensuração mais acurada do risco de quedas no âmbito hospitalar

Diagnóstico de enfermagem risco de quedas em pacientes com angina instável

O risco de quedas pode ser reconhecido como fenômeno ou diagnóstico de enfermagem. Pesquisas relacionam diretamente isquemias miocárdicas, como a angina instável e o risco de cair. Objetivou-se analisar o diagnóstico de enfermagem Risco de quedas na ocorrência de angina instável por um estudo transversal realizado em 57 indivíduos internados em um hospitalescola, mediante exame físico e formulário. Para o tratamento estatístico foram utilizados teste qui-quadrado, teste exato de Fisher, Mann-Whitney, teste-t e Coefi ciente Phi (p<0,05). O Risco de quedas foi o diagnóstico de enfermagem mais prevalente (87,71%), sobretudo em homens, mais velhos, com menos anos de estudo e renda inferior. Presença da angina instável, hipertensão arterial, medicação anti-hipertensiva, doença vascular, difi culdades visuais e insônia apresentaram associação com o diagnóstico de enfermagem Risco de quedas. Conclui-se que é imprescindível o desenvolvimento de parâmetros claros e objetivos à mensuração mais acurada do risco de quedas no âmbito hospitalar

Reperfusión en pacientes con síndrome coronario agudo con elevación del segmento ST en el Hospital Nacional Rosales

La rápida restauración del flujo coronario es un importante factor determinante de la supervivencia en los pacientes con síndrome coronario agudo con elevación del ST. Esto puede lograrse vía farmacológica (fibrinólisis) o mecánica: intervención coronaria percutánea primaria (ICP); se sugiere la utilización de fármacos fibrinolìticos cuando no se dispone de angioplastia en el centro de atención. Objetivo: conocer los resultados del uso de las distintas modalidades de terapia de reperfusión en los pacientes con síndrome coronario agudo con elevación del segmento ST que consultan al Hospital Nacional Rosales. Materiales y métodos: se realizó un estudio descriptivo, longitudinal, retrospectivo de base documental (expedientes clínicos); donde se evaluó el tipo de terapia de reperfusión coronaria utilizada y la evolución clínica en pacientes que consultaron con infarto agudo al miocardio con elevación del ST (IAMST). Resultados: se incluyeron 128 pacientes. El 64.8% recibió terapia de reperfusión. La fibrinólisis con estreptoquinasa fue la modalidad de reperfusión más utilizada, y cuya efectividad se observó según criterios clínicos y electrocardiográficos en el 55.8%. La Intervención coronaria percutánea primaria (ICP) de rescate se realizó en 7 pacientes. Se encontró una mortalidad global del 20.31% y una tasa de reingreso del 25%. Conclusión: en el Hospital Nacional Rosales el manejo del SCA con elevación del ST no es adecuado en el 100% de los pacientes.

Estudio histopatológico de la evolución temporal de las lesiones

En este trabajo se describen los pasos sucesivos que se observan en el proceso de inflamación y reparación de las lesiones con el objeto de poder identificar, en el estudio histopatológico, el estadio en que se encuentran. Los pasos que se siguen en este proceso son los mismos en todos los órganos, a excepción del sistema nervioso. Intentamos que la descripción de las características microscópicas tenga un sentido práctico y pueda ser aplicada y utilizada en el diagnóstico de la data de las lesiones. Las fotos microscópicas que se han elegido se corresponden con el proceso reparativo de los infartos agudos de miocardio con la finalidad de que mantengan una secuencia lógica; sin embargo, mantienen las mismas características histopatológicas que las que pueden apreciarse en la piel o en cualquier otro órgano.

Microstructural-based approach to the interpretation of clays and transitional soils behaviour

Tese (doutorado)—Universidade de Brasília, Faculdade de Tecnologia, Departamento de Engenharia Civil e Ambiental, 2016.