High performance PP/SEBS/CNF composites: evaluation of mechanical, thermal degradation, and crystallization properties

Nanocomposites comprising carbon nanofibers (CNF) were prepared and evaluated in terms of morphology, mechanical performance, thermal stability and crystallization properties. It was found that addition of CNF reinforced polypropylene (PP) matrix by marginally increasing the strength and modulus, but at the expense of toughness and ductility. To improve the toughness of the composites, polystyrene-block-poly(ethylene-ran-butylene)-block-polystyrene (SEBS) was used. Presence of SEBS remarkably improved the toughness and ductility of the composites. The optimum level of reinforcement was observed at 0.1 wt% of CNF in the composites. Phase morphology studies revealed that at this concentration, CNF were well dispersed in polymer phases and beyond it, agglomeration occurred. PP/SEBS/CNF (0.1 wt%) nanocomposites exhibited good strength, excellent toughness and decent modulus, which make them suitable for cost effective, light-weight, tough and stiff material for engineering applications. It was observed that thermal stability of composites is only marginally improved whereas crystallinity of PP drastically reduced by the addition of CNF.

Energy saving in electric heater of carbon fiber stabilization oven

Carbon fiber is an advanced material with high tensile strength and modulus, ideally suited for light weight applications. Carbon fiber properties are directly dependent on all aspects of production, especially the process step of thermal stabilization. Stabilization is considered to be one of the most critical process steps. Moreover, the stabilization process is the most energy consuming, time consuming and costly step. As oxidation is an exothermic process, constant airflow to uniformly remove heat from all tows across the towband is indispensable. Our approach is to develop an intelligent computational system that can construct an optimal Computational Fluid Dynamics (CFD) solution. In this study, an electrical heater has been designed by CFD modeling and intelligently controlled. The model results show that the uniform airflow and minimum turbulence kinetic energy can be achieved by combining intelligent system technology with CFD analysis strategy.

Development and validation of a miniature programmable tDCS device

Research is being conducted on the use of transcranial direct current stimulation (tDCS) for therapeutic effects, and also on the mechanisms through which such therapeutic effects are mediated. A bottleneck in the progress of the research has been the large size of the existing tDCS systems which prevents subjects from performing their daily activities. To help research into the principles, mechanisms, and benefits of tDCS, reduction of size and weight, improvement in simplicity and user friendliness, portability, and programmability of tDCS systems are vital. This paper presents a design for a low-cost, light-weight, programmable, and portable tDCS device. The device is head-mountable and can be concealed in a hat and worn on the head by the subject while receiving the stimulation. The strength of the direct current stimulation can be selected through a simple user interface. The device is constructed and its performance evaluated through bench and in vivo tests. The tests validated the operation of the device in inducing neuromodulatory changes in primary motor cortex, M1, through measuring excitability of dominant M1 of resting right first dorsal interosseus muscle by transcranial magnetic stimulation induced motor evoked potentials. It was observed that the tDCS device induced comparable neuromodulatory effects in M1 as the existing bulky tDCS systems.

Age-Dependent Fragility and Life-Cycle Cost Analysis of Timber and Steel Distribution Poles Subjected to Hurricanes

Power distribution systems are susceptible to extreme damage from natural hazards especially hurricanes. Hurricane winds can knock down distribution poles thereby causing damage to the system and power outages which can result in millions of dollars in lost revenue and restoration costs. Timber has been the dominant material used to support overhead lines in distribution systems. Recently however, utility companies have been searching for a cost-effective alternative to timber poles due to environmental concerns, durability, high cost of maintenance and need for improved aesthetics. Steel has emerged as a viable alternative to timber due to its advantages such as relatively lower maintenance cost, light weight, consistent performance, and invulnerability to wood-pecker attacks. Both timber and steel poles are prone to deterioration over time due to decay in the timber and corrosion of the steel. This research proposes a framework for conducting fragility analysis of timber and steel poles subjected to hurricane winds considering deterioration of the poles over time. Monte Carlo simulation was used to develop the fragility curves considering uncertainties in strength, geometry and wind loads. A framework for life-cycle cost analysis is also proposed to compare the steel and timber poles. The results show that steel poles can have superior reliability and lower life-cycle cost compared to timber poles, which makes them suitable substitutes.

Leakage Temperature Dependency Aware Real-Time Scheduling for Power and Thermal Optimization

Catering to society’s demand for high performance computing, billions of transistors are now integrated on IC chips to deliver unprecedented performances. With increasing transistor density, the power consumption/density is growing exponentially. The increasing power consumption directly translates to the high chip temperature, which not only raises the packaging/cooling costs, but also degrades the performance/reliability and life span of the computing systems. Moreover, high chip temperature also greatly increases the leakage power consumption, which is becoming more and more significant with the continuous scaling of the transistor size. As the semiconductor industry continues to evolve, power and thermal challenges have become the most critical challenges in the design of new generations of computing systems. In this dissertation, we addressed the power/thermal issues from the system-level perspective. Specifically, we sought to employ real-time scheduling methods to optimize the power/thermal efficiency of the real-time computing systems, with leakage/ temperature dependency taken into consideration. In our research, we first explored the fundamental principles on how to employ dynamic voltage scaling (DVS) techniques to reduce the peak operating temperature when running a real-time application on a single core platform. We further proposed a novel real-time scheduling method, “M-Oscillations” to reduce the peak temperature when scheduling a hard real-time periodic task set. We also developed three checking methods to guarantee the feasibility of a periodic real-time schedule under peak temperature constraint. We further extended our research from single core platform to multi-core platform. We investigated the energy estimation problem on the multi-core platforms and developed a light weight and accurate method to calculate the energy consumption for a given voltage schedule on a multi-core platform. Finally, we concluded the dissertation with elaborated discussions of future extensions of our research.

Determination of molecular weight and molecular sizes of polymers by high temperature gel permeation chromatography with a static and dynamic laser light scattering detector

Flow-mode static and dynamic laser light scattering (SLS/DLS) studies of polymers, including polystyrene, polyethylene, polypropylene and poly(dimethylsiloxane) (PDMS), in 1,2,4-trichlorobenzene (TCB) at 150 degreesC were performed on a high temperature gel permeation chromatography (GPC) coupled with a SLS/DLS detector. Both absolute molecular weight (M) and molecular sizes (radius of gyration, R-g and hydrodynamic radius, R-h) of polymers eluting from the GPC columns were obtained simultaneously. The conformation of different polymers in TCB at 150 degreesC were discussed according to the scaling relationships between R-g, R-h and M and the rho-ratio (p = R-g/R-h). Flow-mode DLS results of PDMS were verified by batch-mode DLS study of the same sample. The presented technique was proved to be a convenient and quick method to study the shape and conformation of polymers in solution at high temperature. However, the flow-mode DLS was only applicable for high molecular weight polymers with a higher refractive index increment such as PDMS.

Laser light scattering of the molecular weight distribution of unfractionated phenolphthalein poly(aryl ether sulfone)

Two unfractionated samples of phenolphthalein poly( aryl ether sulfone) (PES-C) were characterized in CHCl3 at 25 degrees C by applying a recently developed laser light-scattering (LLS) procedure. The Laplace inversion of precisely measured intensity-intensity time correlation function lead us first to an estimate of the characteristic line-width distribution G(Gamma) and then to the translational diffusion coefficient distribution G(D). A combination of static and dynamic LLS results enabled us to determine D = (2.69 x 10(-4))M(-0.553), which agrees with the calibration of D = (2.45 x 10(-4))M(-0.55) previously established by a set of narrowly distributed PES-C samples. Using this newly obtained scaling between D and M, we were able to convert G(D) into a differential weight distribution f(w)(M) for the two PES-C samples. The weight-average molecular weights calculated from f(w)(M) are comparable to that obtained directly from static LLS. Our results showed that using two broadly distributed samples instead of a set of narrowly distributed samples have provided not only similar final results, but also a more practical method for the PES-C characterization. (C) 1997 John Wiley & Sons, Inc.

Dynamic light-scattering characterization of the molecular weight distribution of a broadly distributed phenolphthalein poly(aryl ether ketone)

Using a recently developed laser light-scattering (LLS) procedure, we accomplished the characterization of a broadly distributed unfractionated phenolphthalein poly(aryl ether ketone) (PEK-C) in CHCl3 at 25 degrees C. The laplace inversion of precisely measured intensity-intensity time correlation function from dynamic LLS leads us first to an estimate of the characteristic line-width distribution G(Gamma) and then to the translational diffusion coefficient distribution G(D). By using a previously established calibration of D (cm(2)/s) = 2.37 X 10(-4)M(-0.57), were able to convert G(D) into a differential weight distribution f(w)(M). The weight-average molecular weight M(w) calculated from f(w)(M) agrees well with that directly measured in static LLS. Our results indicate that both the calibration and LLS procedure used in this study are ready to be applied as a routine method for the characterization of the molecular weight distribution of PEK-C. (C) 1996 John Wiley & Sons, Inc.

Early light reduction for preventing retinopathy of prematurity in very low birth weight infants

BackgroundRetinopathy of prematurity (ROP) is a complex condition of the developing retinal blood vessels and is one of the leading causes of preventable childhood blindness. Several risk factors for ROP have been studied over the past 50 years. Among them, general immaturity (low birth weight and low gestational age) and prolonged oxygen therapy have been consistently related to disease onset. However, it is understood that the progression of the disease is multifactorial and may be associated with others risk factors, such as multiple gestation, apnoea, intracranial haemorrhage, anaemia, sepsis, prolonged mechanical ventilation, multiple transfusions and light exposure. Furthermore, the precise role of these individual factors in the development of the disease has not yet been well established.ObjectivesTo determine whether the reduction of early environmental light exposure reduces the incidence of retinopathy of prematurity (ROP) or poor ROP outcomes among very low birth weight infants.Search methodsWe searched the following databases: the Cochrane Neonatal Group Specialised Register, CENTRAL (The Cochrane Library), MEDLINE, EMBASE, CINAHL, HealthSTAR, Science Citation Index Database, CANCERLIT, the Oxford Database of Perinatal Trials and www.clinicaltrials.gov. We also searched previous reviews including cross-references, abstracts, conference and symposia proceedings, and contacted expert informants. This search was updated in October 2012.Selection criteriaRandomised or quasi-randomised controlled trials that reduced light exposure to premature infants within the first seven days following birth were considered for this review. We also considered cluster-randomised controlled trials.Data collection and analysisData on clinical outcomes including any acute ROP and poor ROP outcome were extracted by both review authors independently and consensus reached. We conducted data analysis according to the standards of the Cochrane Neonatal Review Group.Main resultsData from four randomised trials with a total of 897 participants failed to show any reduction in acute ROP or poor ROP outcome with the reduction of ambient light to premature infants' retinas. The overall methodological quality of the included studies was about evenly split between those in which the classification was unclear and those in which the studies were categorised as low risk of bias. There was no report on the secondary outcomes considered in this review: quality of life measures; and time of exposure to oxygen.Authors' conclusionsThe evidence shows that bright light is not the cause of retinopathy of prematurity and that the reduction of exposure of the retinas of premature infants to light has no effect on the incidence of the disease.

1980 and 1979 Ford F-150 light truck weight and manufacturing cost analysis. Final report.

National Highway Traffic Safety Administration, Washington, D.C.

1980 and 1979 Ford F-150 light truck weight and material analysis. Final report.

National Highway Traffic Safety Administration, Washington, D.C.

Weight reduction potential of automobiles and light truck. 1980 summary source document. Final report.

National Highway Traffic Safety Administration, Office of Research and Development, Washington, D.C.

Light duty truck weight reduction evaluation. Final report.

National Highway Traffic Safety Administration, Office of Research and Development, Washington, D.C.

Weight reduction potential of automobiles and light trucks, 1979 summary source document. Final report.

National Highway Traffic Safety Administration, Office of Research and Development, Washington, D.C.