Processing and compressive strength of Al-Li-SiCp composites fabricated by a compound billet technique

Al-Li-SiCp composites were fabricated by a simple and cost effective stir casting technique. A compound billet technique has been developed to overcome the problems encountered during hot extrusion of these composites. After successful fabrication hardness measurement and room temperature compressive test were carried out on 8090 Al and its composites reinforced with 8, 12 and 18vol.% SiC particles in as extruded and peak aged conditions. The addition of SiC increases the hardness. 0.2% proof stress and compressive strength of Al-Li-8%SiC and Al-Li-12%SiC composites are higher than the unreinforced alloy. in case of the Al-Li-18%SiC composite, the 0.2% proof stress and compressive strength were higher than the unreinforced alloy but lower than those of Al-Li-8%SiC and Al-Li-12%SiC composites. This is attributed to clustering of particles and poor interfacial bonding.

On the wear of aluminium-corundum composites

The effect of corundum particle content on the wear of aluminium was studied. Composites of different corundum contents were tested for their wear characteristics. Hardness and density measurements were made on specimens before and after test. Specimens were examined by scanning electron microscopy in the as-compacted, sintered and worn states. The wear decreased as the oxide content increased, showing an optimum value at a composition range of 25 wt.%–35 wt.% of corundum. The mechanism of reinforcement and its effect on the operative wear mode are discussed.

Graphene-nanocrystalline metal sulphide composites produced by a one-pot reaction starting from graphite oxide

Graphene-nanocrystalline metal sulphide composites were prepared by a one-pot reaction. A dispersion of graphite oxide layers in an aqueous solution of metal ions (Cd2+/Zn2+) was reacted with H2S gas, which acts as a sulphide source as well as a reducing agent, resulting in the formation of metal sulphide nanoparticles and simultaneous reduction of graphite oxide sheets to graphene sheets. The surface defect related emissions shown by free metal sulphide particles are quenched in the composites due to the interaction of the surface of the nanoparticles with graphene sheets.

Survey of dental clinic patients: Smoking and preferences for cessation support

Background: Smoking cessation interventions delivered by dental practitioners can be as effective as those delivered by general medical practitioners. However, concern that addressing smoking may cause offence to their patients is a reason cited by dental practitioners for not regularly addressing patient smoking behaviours, despite believing they should play a role in smoking cessation. This study aimed to elicit the smoking behaviour and smoking cessation preferences of dental patients to determine if these concerns accurately reflect patient attitudes. Methods: We surveyed 726 adult dental patients attending the University of Queensland’s School of Dentistry Dental Clinics, Brisbane Dental Hospital, and four private dental practices in South East Queensland. Results: Most (80%) current daily smokers had tried to quit smoking. Smokers and non-smokers both agreed that dentists should screen for smoking behaviour and are qualified to offer smoking cessation advice (99% and 96% respectively). Almost all participants (96%) said they would be comfortable with their dentist asking about their smoking and that if their smoking was affecting their oral health their dentist should advise them to quit. Conclusions: Patients are receptive to dental practitioners inquiring about smoking behaviour and offering advice on quitting. Smoking patients showed considerable motivation and interest in quitting smoking, particularly in the context of health problems related to smoking being identified. These results should encourage dentists to raise the issue with their patients.

The effect of a self-development coaching program on the psychological health and the academic performance among medical and dental students in Saudi Arabia

Observational studies have shown that medical and dental students have poor psychological health worldwide; however, few interventional studies have been used to test approaches to help students. This thesis used a randomised control trial study design to evaluate the effect of a self-development coaching program on psychological health and the academic performance among medical and dental students in Saudi Arabia. The outcomes indicated that these medical and dental students in Saudi Arabia experienced high levels of depression, anxiety and stress, and that the self-development coaching program was a promising intervention to improve students' psychological health.

On the wear of aluminium-corundum composites

The effect of corundum particle content on the wear of aluminium was studied. Composites of different corundum contents were tested for their wear characteristics. Hardness and density measurements were made on specimens before and after test. Specimens were examined by scanning electron microscopy in the as-compacted, sintered and worn states. The wear decreased as the oxide content increased, showing an optimum value at a composition range of 25 wt.%–35 wt.% of corundum. The mechanism of reinforcement and its effect on the operative wear mode are discussed.

Dry sliding wear behaviour of magnesium alloy based hybrid composites in the longitudinal direction

In the present investigation, the wear behaviour of a creep-resistant AE42 magnesium alloy and its composites reinforced with Saffil short fibres and SiC particles in various combinations is examined in the longitudinal direction i.e., the plane containing random fibre orientation is perpendicular to the steel counter-face. Wear tests are conducted on a pin-on-disc set-up under dry sliding condition having a constant sliding velocity of 0.837 m/s for a constant sliding distance of 2.5 km in the load range of 10-40 N. It is observed that the wear rate increases with increase in load for the alloy and the composites, as expected. Wear rate of the composites is lower than the alloy and the hybrid composites exhibit a lower wear rate than the Saffil short fibres reinforced composite at all the loads. Therefore, the partial replacement of Saffil short fibres by an equal volume fraction of SiC particles not only reduces the cost but also improves the wear resistance of the composite. Microstructural investigation of the surface and subsurface of the worn pin and wear debris is carried out to explain the observed results and to understand the wear mechanisms. It is concluded that the presence of SiC particles in the hybrid composites improves the wear resistance because these particles remain intact and retain their load bearing capacity even at the highest load employed, they promote the formation of iron-rich transfer layer and they also delay the fracture of Saffil short fibres to higher loads. Under the experimental conditions used in the present investigation, the dominant wear mechanism is found to be abrasion for the AE42 alloy and its composites. It is accompanied by severe plastic deformation of surface layers in case of alloy and by the fracture of Saffil short fibres as well as the formation of iron-rich transfer layer in case of composites.

Small nickel metal particles in Ni---Al2O3 metal-ceramic composites

Magnetic measurements have been used in combination with transmission electron microscopy to investigate small nickel metal particles in metal-ceramic composites. Estimates of the average number of atoms in the particles are given for nonmagnetic samples with low Ni content.

Impression creep behaviour of magnesium alloy-based hybrid composites in the transverse direction

The creep behaviour of a creep-resistant AE42 magnesium alloy reinforced with Saffil short fibres and SiC particulates in various combinations has been investigated in the transverse direction, i.e., the plane containing random fibre orientation was perpendicular to the loading direction, in the temperature range of 175-300 degrees C at the stress levels ranging from 60 to 140 MPa using impression creep test technique. Normal creep behaviour, i.e., strain rate decreasing with strain and then reaching a steady state, is observed at 175 degrees C at all the stresses employed, and up to 80 MPa stress at 240 degrees C. A reverse creep behaviour, i.e., strain rate increasing with strain, then reaching a steady state and then decreasing, is observed above 80 MPa stress at 240 degrees C and at all the stress levels at 300 degrees C. This pattern remains the same for all the composites employed. The reverse creep behaviour is found to be associated with fibre breakage. The apparent stress exponent is found to be very high for all the composites. However, after taking the threshold stress into account, the true stress exponent is found to range between 4 and 7, which suggests viscous glide and dislocation climb being the dominant creep mechanisms. The apparent activation energy Q(C) was not calculated due to insufficient data at any stress level either for normal or reverse creep behaviour. The creep resistance of the hybrid composites is found to be comparable to that of the composite reinforced with 20% Saffil short fibres alone at all the temperatures and stress levels investigated. The creep rate of the composites in the transverse direction is found to be higher than the creep rate in the longitudinal direction reported in a previous paper.

Toughness of as-cast and partially crystallized composites of a bulk metallic glass

The deformation and fracture response of a bulk metallic glass (BMG) post-annealing above the glass transition temperature is examined. The toughness of the glass-matrix composite exhibits a sharp transition beyond a critical volume fraction of crystallization to values as low as that of brittle silicate glass. Instrumented indentation tests supplemented by impact tests were used to study this ductile to brittle transition exhibited by the partially crystallized samples. Indentation on the anneal-embrittled specimens shows lateral cracks in addition to cracks along the corners. The applicability of the Poisson's ratio-toughness correlation with respect to partially crystallized samples is also investigated.

Preventive Dentistry and Dental Education in Iran

The present study investigated the preventive orientation of the dental education system in Iran as reflected in the responses of dental school educators and dental students to a questionnaire survey. Two questionnaires, one for dental school educators and one for senior dental students, were designed and piloted. Of the 15 state dental schools in Iran, 7 were selected using a multi-stage sampling approach, and all the dental school educators and senior dental students in these schools were asked to voluntarily fill in the anonymous questionnaires. Totally, 291 educators (80%) and 270 students (82%) participated in the study. In addition to background information, both questionnaires requested information on knowledge of caries prevention, attitudes towards preventive dentistry and oral health behaviour of the respondents. The students' questionnaire also covered items concerning prevention-oriented practice, study motives, and career preferences. Contrary to knowledge and attitudes of the students, those of the educators' were positively associated with some of their academic and personal background characteristics. Women were more likely to report favourable oral self-care habits than men. The other determinants of oral health behaviour were educators' familiarity with the oral public health field, and students' attitudes towards prevention. A higher score on preventive practice among the students was associated with better oral self-care habits and positive attitudes towards prevention. Characteristics of the profession and social status and security were the top-ranked that motivated students to study dentistry, and students mainly preferred to enter postgraduate courses and private practice after graduation. To increase the orientation of Iran's health care system towards prevention, and to cope with current concepts of prevention, corresponding changes should be made in the dental education system. The results of this study support the revision of the dental curriculum by placing more emphasis on prevention-related topics and by integrating prevention-related concepts into all disciplines. Additionally, practicing dentists and dental educators should be provided with opportunities to attend continuing education courses and to conduct seminars and congresses on various aspects of preventive dentistry at home as well as abroad.

Impact of dental insurance on adults’ oral health care in Tehran, Iran.

The aim of the present study was to determine relationships between insurance status and utilization of oral health care and its characteristics and to identify factors related to insured patients’ selection of dental clinic or dentist. The study was based on cross-sectional data obtained through phone interviews. The target population included adults in the city of Tehran. Using a two-stage stratified random technique, 3,200 seven-digit numbers resembling real phone numbers were drawn; when calling, 1,669 numbers were unavailable (busy, no answer, fax, line blocked). Of the 1,531 subjects who answered the phone call, 224 were outside the target age (under 18), and 221 refused to respond, leaving 1,086 subjects in the final sample. The interviews were carried out using a structured questionnaire and covered characteristics of dental visits, the respondent’s reason for selecting a particular dentist or clinic and demographic and socio-economic background (gender, age, level of education, income, and insurance status). Data analysis included the Chi-square test, ANOVA, and logistic regression and the corresponding odds ratios (OR). Of all the 1,086 respondents, 57% were women, 62% were under age 35, 46% had a medium and 34% a high level of education, 13% were under the poverty line, and 70% had insurance coverage; 64% with the public, and 6% with a commercial insurance. Having insurance coverage was more likely for women (OR=1.5), for those in the oldest age group (OR=2.0), and for those with a high level of education (OR=2.5). Of those with dental insurance, 54% reported having had a dental visit within the past 12 months ; more often by those with commercial insurance in comparison with public (65% vs. 53% p<0.001). Check-up as the reason for the most recent visit occurred most frequently among those with commercial insurance (28%) compared with those having public insurance (16%) or being non-insured (13%) (p<0.001). Having had two or more dental visits within the past 12 months was most common among insured respondents, when compared with the non-insured (31% vs. 22% p=0.01). The non-insured respondents reported tooth extractions almost twice as frequently as did the insured ones (p<0.001). Of the 726 insured subjects, 60% selected fully out-of-pocket-paid services (FOP), and 53% were unaware of their insurance benefits. Of those who selected FOP, good interpersonal aspects (OR=4.6), being unaware of dental insurance benefits (OR=4.6), and good technical aspects (OR=2.3) as a reason had greater odds of selecting FOP. The present study revealed that dental insurance was positively related to demand for oral health care as well as to utilization of services, but to the latter with a minor extent. Among insured respondents, despite their opportunity to use fully or highly subsidized oral health care services, good interpersonal relationship and high quality of services were the most important factors when an insured patient selected a dentist or a clinic. The present findings indicate a clear need to modify dental insurance systems in Iran to facilitate optimal use of oral health care services to maximize the oral health of the population. A special emphasis in the insurance schemes should be focused on preventive care.