Influence of A-type Zeolite on Methane Hydrate Formation

The porous medium has an important effect on hydrate formation. In this paper, the formation process and the gas storage capacity of the methane hydrate were investigated with A-type zeolite and Sodium Dodecyl Sulfate (SDS) existing in the system. The results show that A-type zeolite can influence methane hydrate formation. At the temperature of 273.5 K and pressure of 8.3 MPa, the distilled water with A-type zeolite can form methane hydrate with gaseous methane in 12 hours. The formation process of the system with A-type zeolite was quite steady and the amount of A-type zeolite can influence the gas storage capacity significantly. The adding of A-type zeolite with 0.067 g.(g water)(-1) into 2 x 10(-3) g.g(-1) SDS-water solution can increase the gas storage capacity, and the maximum increase rate was 31%. Simultaneously the promotion effect on hydrate formation of 3A-type zeolite is much more obvious than that of 5A-type zeolite when the water adding amounts are 0.033 g.g(-1) and 0.067 g.g(-1) at the experimental conditions.

Molecular Dynamics Simulation on Characteristics of Decomposition of Methane Hydrate in the Presence of Hydrogen Peroxide Solution

In this work, the characteristics of the decomposition of methane hydrate Structure I (SI) in the presence of hydrogen peroxide solution is investigated using the molecular dynamics simulation. The mechanism of the transformation process from the solid hydrate to the liquid is analyzed with the effect of hydrogen peroxide (HP) solution. In addition, the effect of ethylene glycol (EG) with the same molar concentration with HP on the methane hydrate dissociation is also studied. The results illustrate that both HP and EG promote well the hydrate dissociation. The work provides the important reference value for the experimental investigation into the promotion effect of HP on the hydrate dissociation.

The methane hydrate formation and the resource estimate resulting from free gas migration in seeping seafloor hydrate stability zone

It is a typical multiphase flow process for hydrate formation in seeping seafloor sediments. Free gas can not only be present but also take part in formation of hydrate. The volume fraction of free gas in local pore of hydrate stable zone (HSZ) influences the formation of hydrate in seeping seafloor area, and methane flux determines the abundance and resource of hydrate-bearing reservoirs. In this paper, a multiphase flow model including water (dissolved methane and salt)-free gas hydrate has been established to describe this kind of flow-transfer-reaction process where there exists a large scale of free gas migration and transform in seafloor pore. In the order of three different scenarios, the conversions among permeability, capillary pressure, phase saturations and salinity along with the formation of hydrate have been deducted. Furthermore, the influence of four sorts of free gas saturations and three classes of methane fluxes on hydrate formation and the resource has also been analyzed and compared. Based on the rules drawn from the simulation, and combined information gotten from drills in field, the methane hydrate(MH) formation in Shenhu area of South China Sea has been forecasted. It has been speculated that there may breed a moderate methane flux below this seafloor HSZ. If the flux is about 0.5 kg m-2 a-1, then it will go on to evolve about 2700 ka until the hydrate saturation in pore will arrive its peak (about 75%). Approximately 1.47 109 m3 MH has been reckoned in this marine basin finally, is about 13 times over preliminary estimate.

Methane hydrate growth velocity in seepage system of Qiongdongnan Basin, South China Sea

The occurrences of diapirs, gas-filled zones and gas plumes in seawater in Qiongdongnan Basin of South China Sea indicate that there may exist seepage system gas-hydrate reservoirs. Assuming there has a methane venting zone of 1500 m in diameter, and the methane flux is 1000 kmol/a, and the temperature of methane hydrate-bearing sediments ranges from 3 degrees C to 20 degrees C, then according to the hydrate film growth theory, by numerical simulation, this paper computes the temperatures and velocities in 0 mbsf, 100 mbsf, 200 mbsf, 425 mbsf over discrete length, and gives the change charts. The results show that the cementation velocity in sediments matrix of methane hydrate is about 0.2 nm/s, and the seepage system will evolve into diffusion system over probably 35000 years. Meanwhile, the methane hydrate growth velocity in leakage system is 20 similar to 40 times faster than in diffusion system.

Molecular Dynamics Simulation of Methane Hydrate Dissociation Process in the Presence of Thermodynamic Inhibitor

The dissociation of methane hydrate in the presence of ethylene glycol (11.45 mol.L-1) at 277.0 K was studied using canonical ensemble (NVT) molecular dynamics simulations. Results show that hydrate dissociation starts from the surface layer of the solid hydrate and then gradually expands to the internal layer. Thus, the solid structure gradually shrinks until it disappears. A distortion of the hydrate lattice structure occurs first and then the hydrate evolves from a fractured frame to a fractional fragment. Finally, water molecules in the hydrate construction exist in the liquid state. The inner dissociating layer is, additionally, coated by a liquid film formed from outer dissociated water molecules outside. This film inhibits the mass transfer performance of the inner molecules during the hydrate dissociation process.

Experimental Investigation into the Production Behavior of Methane Hydrate in Porous Sediment with Hot Brine Stimulation

The gas production behavior from methane hydrate in porous sediment by injecting the brine with the salinity of 0−24 wt % and the temperature of −1 to 130 °C was investigated in a one-dimensional experimental apparatus. The results show that the gas production process consists of three periods: the free gas production, the hydrate dissociation, and the general gas reservoir production. The hydrate dissociation accompanies the temperature decrease with the injection of the brine (NaCl solution), and the dissociation duration is shortened with the increase of the salinity. With the injection of hot brine, instantaneous hydrate dissociation rate also increases with the increase of the salinity. However, while the NaCl concentration is beyond a certain value, the rate has no longer continued increasing. Thermal efficiency and energy ratio for the hydrate production can be enhanced by injecting hot brine, and the enhanced effectiveness is quite good with the injection of high salinity at lower temperature.

Replacement of methane from quartz sand-bearing hydrate with carbon dioxide-in-water emulsion

The replacement of CH4 from its hydrate in quartz sand with 90:10, 70:30, and 50:50 (W-CO2:W-H2O) carbon dioxide-in-water (C/W) emulsions and liquid CO2 has been performed in a cell with size of empty set 36 x 200 mm. The above emulsions were formed in a new emulsifier, in which the temperature and pressure were 285.2 K and 30 MPa, respectively, and the emulsions were stable for 7-12 h. The results of replacing showed that 13.1-27.1%, 14.1-25.5%, and 14.6-24.3% of CH4 had been displaced from its hydrate with the above emulsions after 24-96 It of replacement, corresponding to about 1.5 times the CH4 replaced with high-pressure liquid CO2. The results also showed that the replacement rate of CH4 with the above emulsions and liquid CO2 decreased from 0.543, 0.587, 0.608, and 0.348 1/h to 0.083, 0.077, 0.069, and 0.063 1/h with the replacement time increased from 24 to 96 h. It has been indicated by this study that the use of CO2 emulsions is advantageous compared to the use of liquid CO2 in replacing CH4 from its hydrate.

Use of electrical resistance to detect the formation and decomposition of methane hydrate

The changes of electrical resistance (R) were studied experimentally in the process of CH4 hydrate formation and decomposition, using temperature and pressure as the auxiliary detecting methods simultaneously. The experiment results show that R increases with hydrate formation and decreases with hydrate decompositon. R is more sensitive to hydrate formation and decompositon than temperature or pressure, which indicates that the detection of R will be an effective means for detecting natural gas hydrate (NGH) quantitatively.

Determination of appropriate condition on replacing methane from hydrate with carbon dioxide

This paper is intended to determine the appropriate conditions for replacing CH4 from NGH with CO2. By analyzing the hydration equilibrium graphs and geotherms, the HSZs of NGH and CO2 hydrate, both in permafrost and under deep sea, were determined. Based on the above analysis and experimental results, it is found that to replace CH4 from NGH with gaseous CO2, the appropriate experimental condition should be in the area surrounded by four curves: the geotherm, (H-V)(CO2), (L-V)(CO2) and (H-V)(CH4), and to replace CH4 from NGH with liquid CO2, the condition should be in the area surrounded by three curves: (L-V)(CO2), (H-L)(CO2) and (H-V)CH4. For conditions in other areas, either CO2 can not form a hydrate or CH4 can release little from its hydrate, which are not desirable results.

Experimental investigation of production behavior of methane hydrate under ethylene glycol injection in unconsolidated sediment

This article investigates the gas production behavior from methane hydrate (MH) in porous sediment by injecting ethylene glycol (EG) solution with the different concentrations and the different injection rates in an one-dimensional experimental apparatus. The results suggest that the gas production process can be divided into the four stages: (1) the initial injection, (2) the EG diluteness, (3) the hydrate dissociation, and (4) the remained gas output. Nevertheless, the water production rate keeps nearly constant during the whole production process. The production efficiency is affected by both the EG concentration and the EG injection rate, and it reaches a maximum with the EG concentration of 60 wt %.

Clathrate Dissociation Conditions for Methane + Tetra-n-butyl Ammonium Bromide (TBAB) + Water

Hydrate equilibrium data of the CH4 + tetra-n-butyl ammonium bromide (TBAB) + water have been measured by using the isothermal pressure search method for four components of TBAB aqueous solutions. The three-phase equilibrium lines obtained in the present study are shifted to the low-temperature or high-pressure side from that of the stoichiometric TBAB solution. Moreover, methane uptake into semi-clathrates is confirmed by a shift in the clathrate regions when methane is present. The experiments are carried out in the pressure range of (0.5 to 11) MPa and in the temperature range of (281.15 to 295.15) K.

Study on methane hydration process in a semi-continuous stirred tank reactor

The methane hydration process is investigated in a semi-continuous stirred tank reactor. Liquid temperatures and reaction rates without stirrer are compared with those occurring with stirrer, while at the same time better stirring conditions of the methane hydration process are given by the experiments. Some basic data of fluid mechanics, for example, stirring Reynolds number, Froucle number and stirrer power, are calculated during the methane hydration process, which can be applied to evaluate stirrer capacity and provide some basic data for a scaled up reactor. Based on experiment and calculations in this work, some conclusions are drawn. First, the stirrer has great influence on the methane hydration process. Batch stirring is helpful to improve the mass transfer and heat transfer performances of the methane hydration process. Second, induction time can be shortened effectively by use of the stirrer. Third, in this paper, the appropriate stirring velocity and stirring time were 320 rpm and 30 min, respectively, at 5.0 MPa, for which the storage capacity and reaction time were 159.1 V/V and 370 min, respectively. Under the condition of the on-flow state, the initial stirring Reynolds number of the fluid and the stirring power were 12,150 and 0.54 W, respectively. Fourth, some suggestions, for example, the use of another type of stirrer or some baffles, are proposed to accelerate the methane hydration process. Comparing with literature data, higher storage capacity and hydration rate are achieved in this work. Moreover, some fluid mechanics parameters are calculated, which can provide some references to engineering application.