Chipless RFID Tag Using Multiple Microstrip Open Stub Resonators

A novel compact RFID tag employing open stubs in a microstrip transmission line is proposed. The prototype of the tag is fabricated on a substrate of dielectric constant 4.4 and loss tangent 0.0018. The tag consists of microstrip open stub resonators and cross polarized transmitting and receiving disc monopole antennas. A prototype of 8 bit data encoded tag is demonstrated in this communication. Method for enhancing the performance of the RFID tag is also proposed. Magnitude or group delay response can be used to decode the tag informations

A compact CPW fed slot antenna for ultra wide band applications

A printed compact coplanar waveguide fed triangular slot antenna for ultra wide band (UWB) communication systems is presented. The antenna comprises of a triangular slot loaded ground plane with a T shaped strip radiator to enhance the bandwidth and radiation. This compact antenna has a dimension of 26mm×26mm when printed on a substrate of dielectric constant 4.4 and thickness 1.6mm. Design equations are implemented and validated for different substrates. The pulse distortion is insignificant and is verified by the measured antenna performance with high signal fidelity and virtually steady group delay. The simulation and experiment reveal that the proposed antenna exhibits good impedance match, stable radiation patterns and constant gain and group delay over the entire operating band

Compact Uniplanar Antenna for Multiband Applications

A dual band RFID applications in 800 900 MHz and 2400 MHz band is presented. The Asymmetric Coplanar Strip (ACS) fed antenna consists of inverted L shaped monopole with a capacitive loading to provide necessary impedance matching and current distribution. The antenna has wide bandwidth from 790 MHz tol050 MHz and from 2350 MHz to 2640 MHz coving the RFID UHF and Microwave frequencies. The uniplanar antenna having overall dimensions of 48 mm x 14 mm is printed on one side of a substrate of dielectric constant 4.4 and height 1.6 mm.

Frequency Coded Chipless RFID Tag using Spurline Resonators

A novel compact chipless RFID tag using spurline resonators is discussed in this paper. The detection of the tag's ID is using the spectral signature of a spurline resonator circuit. The tag has a data capacity of 8-bits in the range 2.38 to 4.04 GHz. The tag consists of a spurline multiresonating circuit and two cross polarized antennas. The prototype of the tag is fabricated on a substrate CMET/ LK4.3 of dielectric constant 4.3 and loss tangent 0.0018. The measured results show that group delay response can also be used to decode the tag’s identity

A Planar Compact Metamaterialinspired Broadband Antenna

An electrically small, broadband-modified, truncated ground metamaterial EZ antenna is presented. This, a modified EZ antenna system, achieves a larger bandwidth of the order of 650 MHz by adjusting the metamaterial-inspired meandered ground element fed by a top loaded monopole. The design is devoid of the large ground planes and the external parasitic elements used in conventional designs for achieving proper impedance matching characteristics. The antenna requires a small foot print of kg/5 3 kg/10, where kg is the guided wavelength corresponding to the lowest frequency of operation, when printed on a substrate of dielectric constant 4.4 and thickness 1.6 mm. The antenna offers a 2:1 VSWR bandwidth from 750 MHz to 1.4 GHz, which covers CDMA, GSM, and ISM bands

Compact CPW-fed uniplanar antenna for multiband wireless applications

A compact coplanar waveguide (CPW) fed uniplanar antenna for Quad-band applications is presented. The Quad-band operation is realized by imposing various current paths in a modified T-shaped radiating element. The antenna covers GSM 900, DCS 1800, IEEE802.11.a, IEEE802.11.b and HiperLAN-2 bands and exhibits good radiation characteristics. This low profile antenna has a dimension of 32mm×31mmwhen printed on a substrate of dielectric constant 4.4 and height 1.6mm. Details of design with experimental and simulated results are presented

CPW-Fed Quad-Band Antenna for Compact Wireless Application

This paper presents the design and development of a compact CPW fed quad band antenna. This low profile antenna has a dimension of 32mmx31mm when printed on a substrate of dielectric constant 4.4 and height 1.6mm. The antenna covers GSM 900, DCS 1800, IEEE802.11.a, IEEE802.11.b and HiperLAN2 bands. The antenna exhibits good radiation characteristics with moderate gain

Low k thin films based on rf plasma-polymerized aniline

Thermally stable materials with low dielectric constant (k < 3.9) are being hotly pursued. They are essential as interlayer dielectrics/intermetal dielectrics in integrated circuit technology, which reduces parasitic capacitance and decreases the RC time constant. Most of the currently employed materials are based on silicon. Low k films based on organic polymers are supposed to be a viable alternative as they are easily processable and can be synthesized with simpler techniques. It is known that the employment of ac/rf plasma polymerization yields good quality organic thin films, which are homogenous, pinhole free and thermally stable. These polymer thin films are potential candidates for fabricating Schottky devices, storage batteries, LEDs, sensors, super capacitors and for EMI shielding. Recently, great efforts have been made in finding alternative methods to prepare low dielectric constant thin films in place of silicon-based materials. Polyaniline thin films were prepared by employing an rf plasma polymerization technique. Capacitance, dielectric loss, dielectric constant and ac conductivity were evaluated in the frequency range 100 Hz– 1 MHz. Capacitance and dielectric loss decrease with increase of frequency and increase with increase of temperature. This type of behaviour was found to be in good agreement with an existing model. The ac conductivity was calculated from the observed dielectric constant and is explained based on the Austin–Mott model for hopping conduction. These films exhibit low dielectric constant values, which are stable over a wide range of frequencies and are probable candidates for low k applications.

Multiferroic Behavior of Gd Based Manganite

Here we report the multiferroic nature of charge ordered manganite Gd0.5Sr0.5MnO3 for the first time. The temperature variation of dielectric constant shows broad relaxor type ferroelectric transition at around 210K and magnetization measurements shows weak ferromagnetism at 50K. The dielectric peak is very close to charge ordering temperature which is an evidence of the link between electronic state and increase of dielectric response. Butterfly variation of capacitance with voltage confirms ferroelectric nature of the sample at room temperature

Microwave exfoliated reduced graphene oxide epoxy nanocomposites for high performance applications

Graphene has captured the attention of scientific community due to recently emerging high performance applications. Hence, studying its reinforcing effects on epoxy resin is a significant step. In this study, microwave exfoliated reduced graphene oxide (MERGO) was prepared from natural graphite for subsequent fabrication of epoxy nanocomposites using triethylenetetramine (TETA) as a curing agent via insitu polymerization. Thermogravimetric analysis (TGA), X-ray diffraction (XRD), Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR), C13 NMR spectroscopy, X-ray photoelectron spectroscopy (XPS) and ultravioletevisible (UVevis) spectroscopy were employed to confirm the simultaneous reduction and exfoliation of graphene oxide. The reinforcing effect of MERGO on epoxy resin was explored by investigating its static mechanical properties and dynamic mechanical analysis (DMA) at MERGO loadings of 0 to 0.5 phr. The micro-structure of epoxy/MERGO nanocomposites was investigated using scanning electron microscope (SEM), transmission electron microscope (TEM) and XRD techniques. The present work reports an enhancement of 32%, 103% and 85% in tensile, impact and flexural strength respectively of epoxy by the addition of even 0.25 phr MERGO. At this loading elastic and flexural moduli also increased by 10% and 65%, respectively. Single-edge-notch three-point-Bending (SEN-TPB) fracture toughness (KIC) measurements were carried out where a 63% increase was observed by the introduction of 0.25 phr MERGO. The interfacial interactions brought about by graphene also benefited the dynamic mechanical properties to a large extent in the form of a significant enhancement in storage modulus and slightly improved glass transition temperature. Considerable improvements were also detected in dielectric properties. The epoxy nanocomposite also attained an ac conductivity of 10 5 S/m and a remarkable increase in dielectric constant. The simple and cost effective way of graphene synthesis for the fabrication of epoxy/MERGO nanocomposites may be extended to the preparation of other MERGO based polymer nanocomposites. This remarkable class of materials has thrown open enormous opportunities for developing conductive adhesives and in microelectronics

Development of selected electro-active polymer-ceramic nanocomposites as pyroelectric thermal/infrared detector materials

The present work emphasises on the synthesis and characterization of electro-active polymer-ceramic nanocomposites which can be used for pyroelectric thermal/infrared detection applications. Two sets of samples belong to polymer-microcrystalline composites have also been investigated in the work. The polymers used in the work have been commercially available ones, but the nanoceramics have been synthesized following simple chemical routes and aqueous organic gel routes. After characterizing the nanoceramics for their structure by powder XRD, they have been dispersed in liquid polymer and sonicated for uniform dispersion. The viscous mixture so formed was cast in the form of films for experimentation. Samples with volume fraction of the ceramic phase varied from 0 to 0.25 have been prepared. Solution growth was followed to prepare microcrystalline samples for the polymer-microcrystalline composites. The physical properties that determine the pyroelectric sensitivity of a material are dielectric constant, dielectric loss, pyroelectric coefficient, thermal conductivity and specific heat capacity. These parameters have been determined for all the samples and compositions reported in this work.The pyroelectric figures of merit for all the samples were determined. The pyroelectric figures of merit that determine the pyroelectric sensitivity of a material are current sensitivity, voltage responsivity and detectivity. All these have been determined for each set of samples and reported in the thesis. In order to assess the flexibility and mouldability of the composites we have measured the Shore hardness of each of the composites by indentation technique and compared with the pyroelectric figures of merit. Some important factors considered during the material fabrication stages were maximum flexibility and maximum figures of merit for pyroelectric thermal/IR detection applications. In order to achieve these goals, all the samples are synthesized as composites of polymers and nano/microcrystalline particles and are prepared in the form of freestanding films. The selected polymer matrices and particle inclusions possess good pyroelectric coefficients, low thermal and dielectric properties, so that good pyroelectric figures of merit could be achieved. The salient features of the work include the particle size of the selected ceramic materials. Since they are in nanometer size it was possible to achieve high flexibility and moldability with high figures of merit for even low volume fractions of inclusions of the prepared nanocrystalline composites. In the case of microcrystalline TGS and DTGS, their composites in PU matrix protect them from fragility and humidity susceptibility and made them for environmental friendly applications.

Fluoreszenz und Lasertätigkeit in dünnen amorphen Schichten von Spirobifluorenderivaten

Es wurden die optischen Eigenschaften einiger Spirooligophenylverbindungen untersucht. Bei den Verbindungen handelte es sich um lineare und verzweigte Derivate des Spirobifluorens. Es wurden dünne amorphe Schichten der Verbindungen mittels spincoating und Vakuumverdampfen (OMBD) auf unterschiedlichen Substraten hergestellt. Mit spektroskopischer Ellipsometrie konnten die Schichtdicken und optische Konstanten der dünnen Schichten bestimmt werden. Dafür sind die Extinktionsspektren mit Tauc-Lorentz-Oszillatoren modelliert worden. Auf diese Weise ließen sich die optischen Konstanten der amorphen Filme besser beschreiben als mit den üblicherweise verwendeten Gauß-Oszillatoren. In dünnen Filmen von Spirosexiphenyl konnte uniaxiale Anisotropie nachgewiesen werden. Im Bereich der pie,pie*-Bande beträgt das Verhältnis des ordentlichen zum außerordentlichen Extinktionskoeffizienten 2.09. Mit einer Integrationskugel wurden die absoluten Quantenausbeuten der Fluoreszenz in festen Filmen bestimmt. Dafür ist ein vereinfachtes Verfahren der Auswertung entwickelt worden. Im Vergleich der untersuchten Substanzen zeigt sich, dass die Verbindungen mit dem Sexiphenyl-Chromophor höhere Quantenausbeuten im Festkörper haben (31 % - 48 %) als die Verbindungen mit Quaterphenyl als Chromophor (15 % - 30 %). In den beiden Klassen haben jeweils die sterisch anspruchsvollen Octopusvarianten die höchsten Festkörperquantenausbeuten. Durch verdünnen mit m,m-Spirosexiphenyl konnte die Quantenausbeute von p,p-Spirosexiphenyl in dünnen festen Filmen bis auf 65 % (95 % m,m- und 5 % p,p-Spirosexiphenyl) gesteigert werden. Eine Korrelation der Quantenausbeuten in Lösung und im festen, unverdünnten Film wurde nicht festgestellt. Als dünne Filme in Wellenleitergeometrie zeigen Spirooligophenyle bei optischer Anregung verstärkte spontane Emission (ASE). Dies manifestiert sich in einer Einengung des Emissionsspektrums mit zunehmender Pumpleistungsdichte. Auch für stimulierte Emission sind die Verbindungen mit Sexiphenylchromophor besser geeignet. Die niedrigste Schwelle in einer unverdünnten Reinsubstanz wurde mit 0.23 µJ/cm² in einer aufgeschleuderten Schicht Spirosexiphenyl gemessen. Auch 4-Spiro³, Spiro-SPO und Octo-2 zeigten niedrige ASE-Schwellen von 0.45 µJ/cm², 0.45 µJ/cm² und 0.5 µJ/cm². Die ASE-Schwellwerte von Spiroquaterphenyl und seinen beiden Derivaten Methoxyspiroquaterphenyl und Octo-1 sind mit 1.8 µJ/cm², 1.4 µJ/cm² und 1.2 µJ/cm² höher als die der Sexiphenylderivate. Im gemischten System aus m,m- und p,p-Spirosexiphenyl konnte die ASE-Schwelle noch weiter gesenkt werden. Bei einer Konzentration von 5 % p,p-Spirosexiphenyl wurde ein Schwellwert von nur 100 nJ/cm² bestimmt. Durch Dotierung mit unterschiedlichen Farbstoffen in Spirosexiphenyl als Matrix konnte ASE fast über den gesamten sichtbaren Spektralbereich gezeigt werden. Mit der „variable Streifenlänge“ (VSL-) -Methode wurden die pumpleistungsabhängigen Gainspektren dünner aufgedampfter Proben gemessen. Hieraus konnten die Wechselwirkungsquerschnitte der stimulierten Emission der Substanzen ermittelt werden. In Übereinstimmung mit den Verhältnissen bei den Festkörperfluoreszenzquantenausbeuten und den Schwellwerten der ASE sind auch bei den Gainkoeffizienten reiner Spirooligophenyle die besten Werte bei den Sexiphenylderivaten gefunden worden. Der Wirkungsquerschnitt der stimulierten Emission beträgt für Methylspiroquaterphenyl und Octo-1 ca. 1.8*10^-17 cm². Für Spiro-SPO und Spirosexiphenyl wurden Wirkungsquerschnitte von 7.5*10^-17 cm² bzw. 9.2*10^-17 cm² bestimmt. Noch etwas größer waren die Werte im gemischten System aus m,m- und p,p-Spirosexiphenyl (1.1*10^-16 cm²) und für DPAVB dotiert in Spirosexiphenyl (1.4*10^-16 cm²). Der höchste Maximalwert des Gainkoeffizienten von 328 cm-1 bei einer absorbierten Pumpenergiedichte von 149 µJ/cm² wurde mit Spirosexiphenyl erreicht. Abschließend wurden DFB-Laser-Strukturen mit reinen und dotierten Spirooligophenylverbindungen als aktiven Materialien vorgestellt. Mit Spiroterphenyl konnte ein DFB-Laser mit der bisher kürzesten Emissionswellenlänge (361.9 nm) in einem organischen Festkörperlaser realisiert werden. Mit reinen Spirooligophenylverbindungen und Mischungen daraus habe ich DFB-Lasing bei Wellenlängen zwischen 361.9 nm und 479 nm aufgezeigt. Durch Dotierung mit DPAVB wurde der Bereich der erreichbaren Wellenlängen bis 536 nm erweitert, bei gleichzeitiger Erniedrigung der Schwellenergiedichten für Lasertätigkeit. Bei Emissionswellenlängen von 495 nm bis 536 nm blieb die Laserschwelle zwischen 0.8 µJ/cm² und 1.1 µJ/cm². Diese Werte sind für DFB-Laser zweiter Ordnung sehr niedrig und geben Anlass zu glauben, dass sich mit DFB-Strukturen erster Ordnung Schwellen im Nanojoule Bereich erzielen lassen. Damit würde man den Bedingungen für elektrisch gepumpten Betrieb nahe kommen.

Radar scattering by aggregate snowflakes

The radar scattering properties of realistic aggregate snowflakes have been calculated using the Rayleigh-Gans theory. We find that the effect of the snowflake geometry on the scattering may be described in terms of a single universal function, which depends only on the overall shape of the aggregate and not the geometry or size of the pristine ice crystals which compose the flake. This function is well approximated by a simple analytic expression at small sizes; for larger snowflakes we fit a curve to Our numerical data. We then demonstrate how this allows a characteristic snowflake radius to be derived from dual wavelength radar measurements without knowledge of the pristine crystal size or habit, while at the same time showing that this detail is crucial to using such data to estimate ice water content. We also show that the 'effective radius'. characterizing the ratio of particle volume to projected area, cannot be inferred from dual wavelength radar data for aggregates. Finally, we consider the errors involved in approximating snowflakes by 'air-ice spheres', and show that for small enough aggregates the predicted dual wavelength ratio typically agrees to within a few percent, provided some care is taken in choosing the radius of the sphere and the dielectric constant of the air-ice mixture; at larger sizes the radar becomes more sensitive to particle shape, and the errors associated with the sphere model are found to increase accordingly.

Conductance and relaxations of gelatin films in the glassy and rubbery states

The dielectric constant, epsilon', and the dielectric loss, epsilon'', for gelatin films were measured in the glassy and rubbery states over a frequency range from 20 Hz to 10 MHz; epsilon' and epsilon'' were transformed into M* formalism (M* = 1/(epsilon' - i epsilon'') = M' + iM''; i, the imaginary unit). The peak of epsilon'' was masked probably due to dc conduction, but the peak of M'', e.g. the conductivity relaxation, for the gelatin used was observed. By fitting the M'' data to the Havriliak-Negami type equation, the relaxation time, tauHN, was evaluated. The value of the activation energy, Etau, evaluated from an Arrhenius plot of 1/tauHN, agreed well with that of Esigma evaluated from the DC conductivity sigma0 both in the glassy and rubbery states, indicating that the conductivity relaxation observed for the gelatin films was ascribed to ionic conduction. The value of the activation energy in the glassy state was larger than that in the rubbery state.

On the concept of electrical impedance for an electrolytic cell

The analysis of the electrical impedance of an electrolytic cell in the shape of a slab is performed. We have solved, numerically, the differential equations governing the phenomenon of the redistribution of the ions in the presence of an external electric field, and compared the results with the ones obtained by solving the linear approximation of these equations. The control parameters in our study are the amplitude and the frequency of the applied voltage, assumed a simple harmonic function of the time. We show that for the large amplitudes of the applied voltage, the actual current is no longer harmonic at low frequencies. From this result it follows that the concept of electrical impedance of a cell is a useful quantity only in the case where the linear approximation of the fundamental equations of problem work well.