Evaluation of the pyrolytic and kinetic characteristics of Enteromorpha prolifera as a source of renewable bio-fuel from the Yellow Sea of China

The pyrolytic and kinetic characteristics of Enteromorpha prolifera from the Yellow Sea were evaluated at heating rates of 10, 20 and 50 degrees C min(-1), respectively. The results indicated that three stages appeared during pyrolysis; dehydration, primary devolatilization and residual decomposition. Differences in the heating rates resulted in considerable differences in the pyrolysis of E. prolifera. Specifically, the increase of heating rates resulted in shifting of the initial temperature, peak temperature and the maximum weight loss to a higher value. The average activation energy of E. prolifera was 228.1 kJ mol(-1), the pre-exponential factors ranged from 49.93 to 63.29 and the reaction orders ranged from 2.2 to 3.7. In addition, there were kinetic compensation effects between the pre-exponential factors and the activation energy. Finally, the minimum activation energy was obtained when a heating rate of 20 degrees C min(-1) was used. (C) 2009 The Institution of Chemical Engineers. Published by Elsevier B.V. All rights reserved.

黄土高原全新世风成沉积的岩石磁学性质

Chinese eolian deposits are especially suitable for the studies of paleoclimatic changes, environmental magnetism and remanence acquisition mechanisms. In the past two decades, many studies have documented their magnetic properties. However, some important problems, such as the origin of magnetic minerals, the mechanisms for enhancing magnetic susceptibility and the lock-in effect, remain debatable. Therefore, it is essential to detail the rock-magnetic properties of the eolian deposits. This study shows thermomagnetic analyses, petrographic measurements and soil chemistry methods can be combined to obtain a better understanding of the sequence of magnetic mineral alterations during thermal treatment and of the pedogenic mechanism responsible for the susceptibility enhancement. This helps to further develop the interpretation of paleoclimate records in the Holocene eolian deposits along a NW-SE transect of the loess plateau. A partial heating/cooling method and X-ray diffraction (XRD) analysis were performed on representative samples of the present-day loess, in order to investigate mineralogical changes during thermal treatment. The temperature-dependent susceptibility (TDS) and XRD results show complex alteration of magnetic phases during heating and cooling. The 300 ℃ susceptibility hump in heating curves might be due to the production of maghemite from less magnetic lepidocrocite during heating. Goethite is transformed into hematite when heating to above 300 ℃. The susceptibility decrease from 300 ℃ to 450 ℃ can be interpreted as the conversion of maghemite to hematite. This thermal instability makes it possible to quantatively estimate the maghemite contribution to the pedogenically-enhanced susceptibility in loess or paleosols. Minor occurrence of thermally-stable maghemite in the present-day loess is possible; nevertheless, the TDS measurements show that the degree of the thermally-induced alteration is closely related to pedogenesis. The TDS measurement and XRD analysis results demonstrate that although magnetite and hematite both exist in the Holocene loess eolian deposits and their modern source area, magnetite is the predominant contributor to magnetic susceptibility. Both magnetite and hematite are the primary carriers of the remanent magnetization. Fine-grained maghemite, mainly produced by pedogenesis, is significantly responsible for enhancement of the magnetic susceptibility in the Chinese loess and paleosols. Since the degree of oxidation of magnetite grains depends on climate, the presence of maghemite has paleoclimatic significance, and variations in climate could be reflected as variations in the amount of low-temperature oxidation. If that is the case, the TDS curves can be used to compare the effects of climate at different sampling sites. The TDS results along the studied NW-SE transect suggest that stronger pedogenesis results in higher content of maghemite and greater susceptibility decrease during thermal treatment. This behavior seems to indicate that the final product of pedogenic magnetite in Chinese loess and paleosols is maghemite, which makes significant contributions to the enhanced magnetic susceptibility of Chinese eolian deposits. It is interesting to note that the 510 ℃ Hopkinson/alteration peak is larger in the present-day loess than in the black loam for each section. Obiviously, the Hopkinson/alteration peak of the Holocene eolian deposits is closely related to the degree of pedogenesis, which is a function of climate, and thus the peak itself could be a useful climate indicator. There are three effects that may be important in producing this trend. First, low-temperature oxidation preferentially affects the finer single-domain magnetites responsible for the Hopkinson peak, which is therefore suppressed in the more oxidized loams. Second, the possible production of uniaxial magnetite with shape anisotropy can also lead to a relatively muted Hopkinson peak. There is, additionally, a third alternative, and the one preferred here, that the natural alteration processes involved in pedogenic susceptibility enhancement have probably depleted the supply of iron-bearing precursor phases, so that less new magnetite is formed on heating. In summary, the TDS method is very reliable and highly sensitive in detecting magnetic phase changes in eolian deposits during thermal treatment, which are closely related to pedogenic processes. Thus, the studied NW-SE transect clearly exhibits paleoclimatically-induced mineral- and rock-magnetic variations. It is suggested that TDS can be used as a new method for the analysis of pedogenesis and climatic change.

Vibrato in singing voice: the link between source-filter and sinusoidal models

The application of inverse filtering techniques for high-quality singing voice analysis/synthesis is discussed. In the context of source-filter models, inverse filtering provides a noninvasive method to extract the voice source, and thus to study voice quality. Although this approach is widely used in speech synthesis, this is not the case in singing voice. Several studies have proved that inverse filtering techniques fail in the case of singing voice, the reasons being unclear. In order to shed light on this problem, we will consider here an additional feature of singing voice, not present in speech: the vibrato. Vibrato has been traditionally studied by sinusoidal modeling. As an alternative, we will introduce here a novel noninteractive source filter model that incorporates the mechanisms of vibrato generation. This model will also allow the comparison of the results produced by inverse filtering techniques and by sinusoidal modeling, as they apply to singing voice and not to speech. In this way, the limitations of these conventional techniques, described in previous literature, will be explained. Both synthetic signals and singer recordings are used to validate and compare the techniques presented in the paper.

Microwave curing for high density package

Summary form only given. Currently the vast majority of adhesive materials in electronic products are bonded using convection heating or infra-red as well as UV-curing. These thermal processing steps can take several hours to perform, slowing throughput and contributing a significant portion of the cost of manufacturing. With the demand for lighter, faster, and smaller electronic devices, there is a need for innovative material processing techniques and control methodologies. The increasing demand for smaller and cheaper devices pose engineering challenges in designing a curing systems that minimize the time required between the curing of devices in a production line, allowing access to the components during curing for alignment and testing. Microwave radiation exhibits several favorable characteristics and over the past few years has attracted increased academic and industrial attention as an alternative solution to curing of flip-chip underfills, bumps, glob top and potting cure, structural bonding, die attach, wafer processing, opto-electronics assembly as well as RF-ID tag bonding. Microwave energy fundamentally accelerates the cure kinetics of polymer adhesives. It provides a route to focus heat into the polymer materials penetrating the substrates that typically remain transparent. Therefore microwave energy can be used to minimise the temperature increase in the surrounding materials. The short path between the energy source and the cured material ensures a rapid heating rate and an overall low thermal budget. In this keynote talk, we will review the principles of microwave curing of materials for high density packing. Emphasis will be placed on recent advances within ongoing research in the UK on the realization of "open-oven" cavities, tailored to address existing challenges. Open-ovens do not require positioning of the device into the cavity through a movable door, hence being more suitable for fully automated processing. Further potential advantages of op- - en-oven curing include the possibility for simultaneous fine placement and curing of the device into a larger assembly. These capabilities promise productivity gains by combining assembly, placement and bonding into a single processing step. Moreover, the proposed design allows for selective heating within a large substrate, which can be useful particularly when the latter includes parts sensitive to increased temperatures.

Determination of absolute ion yields from a MALDI source through calibration of an image-charge detector

MALDI (matrix-assisted laser desorption/ionization) is one of the most important techniques used to produce large biomolecular ions in the gas phase. Surprisingly, the exact ionization mechanism is still not well understood and absolute values for the ion yields are scarce. This is in part due to the unknown efficiencies of typical detectors, especially for heavy biomolecular ions. As an alternative, charged particles can be non-destructively detected using an image-charge detector where the output voltage signal is proportional to the total charge within the device. In this paper, we report an absolute calibration which provides the voltage output per detected electronic charge in our experimental arrangement. A minimum of 3 x 10(3) ions were required to distinguish the signal above background noise in a single pass through the device, which could be further reduced using filtering techniques. The calibration results have been applied to raw MALDI spectra to measure absolute ion yields of both matrix and analyte ions.

Hydrothermal synthesis of a continuous zeolite Beta layer by optimization of time, temperature and heating rate of the precursor mixture

Highly crystalline zeolite Beta coatings in a range of Si/Al ratios of 12-23 were synthesized on a surface-modified molybdenum substrate by hydrothermal synthesis. The average thickness of the coatings was ca. 2 mu m corresponding to a coverage of 2.5 gm(-2). The coatings were obtained from a viscous Na, K, and TEAOH containing aluminosilicate precursor mixture with silica sol as reactive silicon source. A mechanism for the in situ growth of zeolite Beta coatings is proposed. According to this mechanism, the deposition of an amorphous gel layer on the substrate surface in the initial stage of the synthesis is an important step for the crystallization of continuous zeolite Beta coatings. The heating rate of the precursor mixture and the synthesis temperature were optimized to control the level of supersaturation and to stimulate the initial formation of a gel layer. At a Si/Al ratio of 23, fast heating and a temperature of 150 degrees C are required to obtain high coverage, while at a Si/Al ratio of 15, hydrothermal synthesis has to be performed with a slow initial heating rate at 140 degrees C. (c) 2007 Elsevier Inc. All rights reserved.

The identification of potential alternative biomarkers of nitrofurazone abuse in animal derived food products

Semicarbazide (SEM) was considered to be a characteristic protein-bound side-chain metabolite of the banned veterinary drug nitrofurazone and used as a marker of nitrofurazone abuse. It was recently discovered that SEM can arise in food from sources other than nitrofurazone. This uncertainty over the source of SEM may be overcome if alternative markers specific to tissue-bound nitrofurazone residues can be determined. The structure of nitrofurazone metabolites in vivo and particular proteins to which they are bound are not known. These proteins with altered structure due to the presence of the drug metabolites can be considered as potential alternative biomarkers of nitrofurazone abuse. The proteins implicated in the in vivo binding of nitrofurazone were separated and identified. A crude mixture of proteins extracted from the liver of a rat treated with the drug was separated using a series of different techniques such as preparative isoelectric focusing and size exclusion HPLC. Multiple fractions were assayed by LC-MS/MS to detect the presence of SEM. The proteins containing SEM residues were identified by peptide mass mapping using trypsin digestion and MALDI-TOF. The first protein identified as containing high concentration of SEM was albumin. It was also shown that low molecular weight species within a protein mixture whose main constituent was glutathione S-transferase contained a high concentration of SEM. The chemical composition of these components is under investigation. Preliminary data suggest the SEM forms part of a nitrofurazone metabolite conjugated to glutathione. (C) 2008 Elsevier Ltd. All rights reserved.

The OpenPMU Platform for Open Source Phasor Measurements

OpenPMU is an open platform for the development of phasor measurement unit (PMU) technology. A need has been identified for an open-source alternative to commercial PMU devices tailored to the needs of the university researcher and for enabling the development of new synchrophasor instruments from this foundation. OpenPMU achieves this through open-source hardware design specifications and software source code, allowing duplicates of the OpenPMU to be fabricated under open-source licenses. This paper presents the OpenPMU device based on the Labview development environment. The device is performance tested according to the IEEE C37.118.1 standard. Compatibility with the IEEE C37.118.2 messaging format is achieved through middleware which is readily adaptable to other PMU projects or applications. Improvements have been made to the original design to increase its flexibility. A new modularized architecture for the OpenPMU is presented using an open messaging format which the authors propose is adopted as a platform for PMU research.

Heating Mechanisms for Intermittent Loops in Active Region Cores from AIA/SDO EUV Observations

We investigate intensity variations and energy deposition in five coronal loops in active region cores. These were selected for their strong variability in the AIA/SDO 94 Å intensity channel. We isolate the hot Fe XVIII and Fe XXI components of the 94 Å and 131 Å by modeling and subtracting the "warm" contributions to the emission. HMI/SDO data allow us to focus on "inter-moss" regions in the loops. The detailed evolution of the inter-moss intensity time series reveals loops that are impulsively heated in a mode compatible with a nanoflare storm, with a spike in the hot 131 Å signals leading and the other five EUV emission channels following in progressive cooling order. A sharp increase in electron temperature tends to follow closely after the hot 131 Å signal confirming the impulsive nature of the process. A cooler process of growing emission measure follows more slowly. The Fourier power spectra of the hot 131 Å signals, when averaged over the five loops, present three scaling regimes with break frequencies near 0.1 min–1 and 0.7 min–1. The low frequency regime corresponds to 1/f noise; the intermediate indicates a persistent scaling process and the high frequencies show white noise. Very similar results are found for the energy dissipation in a 2D "hybrid" shell model of loop magneto-turbulence, based on reduced magnetohydrodynamics, that is compatible with nanoflare statistics. We suggest that such turbulent dissipation is the energy source for our loops

M-L band x-rays (3-3.5 KeV) from palladium coated targets for isochoric radiative heating of thin foil samples

We describe experiments designed to produce a bright M-L band x-ray source in the 3-3.5 keV region. Palladium targets irradiated with a 10(15) W cm(-2) laser pulse have previously been shown to convert up to similar to 2% of the laser energy into M-L band x-rays with similar pulse duration to that of the incident laser. This x-ray emission is further characterized here, including pulse duration and source size measurements, and a higher conversion efficiency than previously achieved is demonstrated (similar to 4%) using more energetic and longer duration laser pulses (200 ps). The emission near the aluminium K-edge (1.465-1.550 keV) is also reported for similar conditions, along with the successful suppression of such lower band x-rays using a CH coating on the rear side of the target. The possibility of using the source to radiatively heat a thin aluminium foil sample to uniform warm dense matter conditions is discussed.

Open source data sensing software for ultrasonic non-invasive temperature estimation

In this paper, an open source solution for measurement of temperature and ultrasonic signals (RF-lines) is proposed. This software is an alternative to the expensive commercial data acquisition software, enabling the user to tune applications to particular acquisition architectures. The collected ultrasonic and temperature signals were used for non-invasive temperature estimation using neural networks. The existence of precise temperature estimators is an essential point aiming at the secure and effective applica tion of thermal therapies in humans. If such estimators exist then effective controllers could be developed for the therapeutic instrumentation. In previous works the time-shift between RF-lines echoes were extracted, and used for creation of neural networks estimators. The obtained estimators successfully represent the temperature in the time-space domain, achieving a maximum absolute error inferior to the threshold value defined for hyperthermia/diathermia applications.

Estudo de viabilidade técnico-económica da instalação de caldeiras a biomassa para o aquecimento central do ISEP

Neste projeto pretende-se utilizar uma fonte energética renovável (nomeadamente a biomassa), no âmbito da produção de água quente para aquecimento central das instalações do Instituto Superior de Engenharia do Porto (ISEP). O objetivo principal remete para a avaliação técnico-económica da substituição das quinze caldeiras existentes, alimentadas a gás natural, por seis caldeiras alimentadas a biomassa, nomeadamente a pellets. Desta forma, permite-se apostar na biomassa como uma alternativa para reduzir a dependência dos combustíveis fósseis. Neste trabalho apresenta-se uma comparação realista do sistema de aquecimento existente face ao novo a implementar, alimentado por um combustível renovável utilizando caldeiras a pellets de 85% de rendimento. Para realizar esta comparação, usou-se as faturas energéticas de gás natural do ISEP, o custo da quantidade equivalente necessária de pellets, os custos de manutenção dos dois tipos de caldeiras e, os custos do consumo de energia elétrica por parte de ambas as caldeiras. Com este estudo, estimou-se uma poupança anual de 84.100,76 €/ano. Determinaram-se experimentalmente, em laboratório, os parâmetros essenciais de uma amostra de pellets, que foram usados para calcular as necessidades energéticas em biomassa no ISEP, bem como a produção de cinzas gerada por parte das caldeiras. Foi proposto um destino ambientalmente adequado para os 788,5 kg/ano de cinzas obtidas – a utilização na compostagem, após tratamento e aprovação de ensaios ecotoxicológicos realizados pela empresa que fará a sua recolha. As caldeiras a pellets terão um consumo mínimo teórico de 16,47 kgpellets/h, consumindo previsivelmente 197,13 tpellets/ano. Para este efeito, serão usadas caldeiras Quioto de 150 kW da marca Zantia. Para comparar distintas possibilidades de investimento para o projeto, avaliaram-se dois cenários: um foi escolhido de forma a cobrir o somatório da potência instalada das caldeiras atuais e o outro de forma a responder aos consumos energéticos em aquecimento atuais. Além disso, avaliaram-se cenários de financiamento do investimento distintos: um dos cenários corresponde ao pagamento do investimento total do projeto no momento da aquisição das caldeiras, enquanto o outro cenário, mais provável de ser escolhido, refere-se ao pedido de um empréstimo ao banco, no valor de 75% do investimento total. Para o cenário mais provável de investimento, obteve-se um VAL de 291.364,93 €/ano, com taxa interna de rentabilidade (TIR) de 17 %, um índice de rentabilidade (IR) de 1,85 e um período de retorno (PBP) de 5 anos. Todos os cenários avaliados registam rentabilidade do projeto de investimento, sem risco para o projeto.

Source spaces and perturbations for cluster complexes

Dans ce travail, nous définissons des objets composés de disques complexes marqués reliés entre eux par des segments de droite munis d’une longueur. Nous construisons deux séries d’espaces de module de ces objets appelés clus- ters, une qui sera dite non symétrique, la version ⊗, et l’autre qui est dite symétrique, la version •. Cette construction permet des choix de perturba- tions pour deux versions correspondantes des trajectoires de Floer introduites par Cornea et Lalonde ([CL]). Ces choix devraient fournir une nouvelle option pour la description géométrique des structures A∞ et L∞ obstruées étudiées par Fukaya, Oh, Ohta et Ono ([FOOO2],[FOOO]) et Cho ([Cho]). Dans le cas où L ⊂ (M, ω) est une sous-variété lagrangienne Pin± mono- tone avec nombre de Maslov ≥ 2, nous définissons une structure d’algèbre A∞ sur les points critiques d’une fonction de Morse générique sur L. Cette struc- ture est présentée comme une extension du complexe des perles de Oh ([Oh]) muni de son produit quantique, plus récemment étudié par Biran et Cornea ([BC]). Plus généralement, nous décrivons une version géométrique d’une catégorie de Fukaya avec seul objet L qui se veut alternative à la description (relative) hamiltonienne de Seidel ([Sei]). Nous vérifions la fonctorialité de notre construction en définissant des espaces de module de clusters occultés qui servent d’espaces sources pour des morphismes de comparaison.

Carboxydothermus hydrogenoformans comme catalyseur biologique pour la conversion du monoxyde de carbone en hydrogène simultanément a la minéralisation de calcium et phosphate

La gazéification est aujourd'hui l'une des stratégies les plus prometteuses pour valoriser les déchets en énergie. Cette technologie thermo-chimique permet une réduction de 95 % de la masse des intrants et génère des cendres inertes ainsi que du gaz de synthèse (syngaz). Le syngaz est un combustible gazeux composé principalement de monoxyde de carbone (CO), d'hydrogène (H2) et de dioxyde de carbone (CO2). Le syngaz peut être utilisé pour produire de la chaleur et de l'électricité. Il est également la pierre angulaire d'un grand nombre de produits à haute valeur ajoutée, allant de l'éthanol à l'ammoniac et l'hydrogène pur. Les applications en aval de la production de syngaz sont dictées par son pouvoir calorifique, lui-même dépendant de la teneur du gaz en H2. L’augmentation du contenu du syngaz en H2 est rendu possible par la conversion catalytique à la vapeur d’eau, largement répandu dans le cadre du reformage du méthane pour la production d'hydrogène. Au cours de cette réaction, le CO est converti en H2 et CO2 selon : CO + H2O → CO2 + H2. Ce processus est possible grâce à des catalyseurs métalliques mis en contact avec le CO et de la vapeur. La conversion catalytique à la vapeur d’eau a jusqu'ici été réservé pour de grandes installations industrielles car elle nécessite un capital et des charges d’exploitations très importantes. Par conséquent, les installations de plus petite échelle et traitant des intrants de faible qualité (biomasse, déchets, boues ...), n'ont pas accès à cette technologie. Ainsi, la seule utilisation de leur syngaz à faible pouvoir calorifique, est limitée à la génération de chaleur ou, tout au plus, d'électricité. Afin de permettre à ces installations une gamme d’application plus vaste de leurs syngaz, une alternative économique à base de catalyseur biologique est proposée par l’utilisation de bactéries hyperthermophiles hydrogénogènes. L'objectif de cette thèse est d'utiliser Carboxydothermus hydrogenoformans, une bactérie thermophile carboxydotrophe hydrogénogène comme catalyseur biologique pour la conversion du monoxyde de carbone en hydrogène. Pour cela, l’impact d'un phénomène de biominéralisation sur la production d’H2 a été étudié. Ensuite, la faisabilité et les limites de l’utilisation de la souche dans un bioréacteur ont été évaluées. Tout d'abord, la caractérisation de la phase inorganique prédominante lorsque C. hydrogenoformans est inoculé dans le milieu DSMZ, a révélé une biominéralisation de phosphate de calcium (CaP) cristallin en deux phases. L’analyse par diffraction des rayons X et spectrométrie infrarouge à transformée de Fourier de ce matériau biphasique indique une signature caractéristique de la Mg-whitlockite, alors que les images obtenues par microscopie électronique à transmission ont montré l'existence de nanotiges cristallines s’apparentant à de l’hydroxyapatite. Dans les deux cas, le mode de biominéralisation semble être biologiquement induit plutôt que contrôlé. L'impact du précipité de CaP endogène sur le transfert de masse du CO et la production d’H2 a ensuite été étudié. Les résultats ont été comparés aux valeurs obtenues dans un milieu où aucune précipitation n'est observée. Dans le milieu DSMZ, le KLa apparent (0.22 ± 0.005 min-1) et le rendement de production d’H2 (89.11 ± 6.69 %) étaient plus élevés que ceux obtenus avec le milieu modifié (0.19 ± 0.015 min-1 et 82.60 ± 3.62% respectivement). La présence du précipité n'a eu aucune incidence sur l'activité microbienne. En somme, le précipité de CaP offre une nouvelle stratégie pour améliorer les performances de transfert de masse du CO en utilisant les propriétés hydrophobes de gaz. En second lieu, la conversion du CO en H2 par la souche Carboxydothermus hydrogenoformans fut étudiée et optimisée dans un réacteur gazosiphon de 35 L. Parmi toutes les conditions opérationnelles, le paramètre majeur fut le ratio du débit de recirculation du gaz sur le débit d'alimentation en CO (QR:Qin). Ce ratio impacte à la fois l'activité biologique et le taux de transfert de masse gaz-liquide. En effet, au dessus d’un ratio de 40, les performances de conversion du CO en H2 sont limitées par l’activité biologique alors qu’en dessous, elles sont limitées par le transfert de masse. Cela se concrétise par une efficacité de conversion maximale de 90.4 ± 0.3 % et une activité spécifique de 2.7 ± 0.4 molCO·g–1VSS·d–1. Malgré des résultats prometteurs, les performances du bioréacteur ont été limitées par une faible densité cellulaire, typique de la croissance planctonique de C. hydrogenoformans. Cette limite est le facteur le plus contraignant pour des taux de charge de CO plus élevés. Ces performances ont été comparées à celles obtenues dans un réacteur à fibres creuses (BRFC) inoculé par la souche. En dépit d’une densité cellulaire et d’une activité volumétrique plus élevées, les performances du BRFC à tout le moins cinétiquement limitées quand elles n’étaient pas impactées par le transfert de masse, l'encrassement et le vieillissement de la membrane. Afin de parer à la dégénérescence de C. hydrogenoformans en cas de pénurie de CO, la croissance de la bactérie sur pyruvate en tant que seule source de carbone a été également caractérisée. Fait intéressant, en présence simultanée de pyruvate et de CO, C. hydrogenoformans n’a amorcé la consommation de pyruvate qu’une fois le CO épuisé. Cela a été attribué à un mécanisme d'inhibition du métabolisme du pyruvate par le CO, faisant ainsi du pyruvate le candidat idéal pour un système in situ de secours.

Marine Bacteria As Source Of Pigment For Application As Dye In Textile Industry

The textile industry is one amongst the rapidly growing industries world wide, which utilizes enormous amounts of synthetic dyes. Consequently, the effluent from these textile industries poses serious threat to the environment which is often very difficult to treat and dispose. This has become a very grave problem in environment conservation and hence natural pigments have drawn the attention of industry as safe alternative. In this context, in the present study an attempt was made to bioprospect marine bacteria towards isolation of a suitable and ideal pigment that could be used as a natural dye. A marine Serratia sp. BTWJ8 was recognized to synthesize enormous amounts of a prodigiosin-like pigment. The pigment was isolated and characterized for various properties. The pigment was evaluated for application as a dye in the textile industry. Results of the studies indicated that this pigment could be used as a natural dye for imparting red-yellow colour to various grades of textile materials. The colour was observed to be stable after wash performance studies