Interactions between Building Integrated Photovoltaics and microclimate in urban environments

BIPV(Building Integrated Photovoltaics) has progressed in the past years and become an element to be considered in city planning. BIPV has influence on microclimate in urban environments and the performance of BIPV is also affected by urban climate. The effect of BIPV on urban microclimate can be summarized under the following four aspects. The change of absorptivity and emissivity from original building surface to PV will change urban radiation balance. After installation of PV, building cooling load will be reduced because of PV shading effect, so urban anthropogenic heat also decreases to some extent. Because PV can reduce carbon dioxide emissions which is one of the reasons for urban heat island, BIPV is useful to mitigate this phenomena. The anthropogenic heat will alter after using BIPV, because partial replacement of fossil fuel means to change sensible heat from fossil fuel to solar energy. Different urban microclimate may have various effects on BIPV performance that can be analyzed from two perspectives. Firstly, BIPV performance may decline with the increase of air temperature in densely built areas because many factors in urban areas cause higher temperature than that of the surrounding countryside. Secondly, the change of solar irradiance at the ground level under urban air pollution will lead to the variation of BIPV performance because total solar irradiance usually is reduced and each solar cell has a different spectral response characteristic. The thermal model and performance model of ventilated BIPV according to actual meteorologic data in Tianjin(China) are combined to predict PV temperature and power output in the city of Tianjin. Then, using dynamic building energy model, cooling load is calculated after BIPV installation. The calculation made based in Tianjin shows that it is necessary to pay attention to and further analyze interaction between them to decrease urban pollution, improve BIPV Performance and reduce colling load. Copyright © 2005 by ASME.

Autoignition of alcohols and ethers in a rapid compression machine

The autoignition characteristics of methanol, ethanol and MTBE (methyl tert-butyl ether) have been investigated in a rapid compression machine at pressures in the range 20-40 atm and temperatures within 750-1000 K. All three oxygenated fuels tested show higher autoignition temperatures than paraffins, a trend consistent with the high octane number of these fuels. The autoignition delay time for methanol was slightly lower than predicted values using reported reaction mechanisms. However, the experimental and measured values for the activation energy are in very good agreement around 44 kcal/mol. The measured activation energy for ethanol autoignition is in good agreement with previous shock tube results (31 kcal/mol), although ignition times predicted by the shock tube correlation are a factor of three lower than the measured values. The measured activation energy for MTBE, 41.4 kcal/mol, was significantly higher than the value previously observed in shock tubes (28.1 kcal/mol). The onset of preignition, characterized by a slow energy release prior to early ignition was observed in some instances. Possible reasons for these ocurrences are discussed. © Copyright 1993 Society of Automotive engineers, Inc.

A combined nonfertile and UO2 PWR fuel assembly for actinide waste minimization

A new combined Non Fertile and Uranium (CONFU) fuel assembly is proposed to limit the actinides that need long-term high-level waste storage from the pressurized water reactor (PWR) fuel cycle. In the CONFU assembly concept, ∼20% of the UO2 fuel pins are replaced with fertile free fuel hosting the transuranic elements (TRUs) generated in the previous cycle. This leads to a fuel cycle sustainable with respect to net TRU generation, and the amount and radiotoxicity of the nuclear waste can be significantly reduced in comparison with the conventional once-through UO2 fuel cycle. It is shown that under the constraints of acceptable power peaking limits, the CONFU assembly exhibits negative reactivity feedback coefficients comparable in values to those of the reference UO2 fuel. Feasibility of the PWR core operation and control with complete TRU recycle has been shown based on full-core three-dimensional neutronic simulation. However, gradual buildup of small amounts of Cm and Cf challenges fuel reprocessing and fabrication due to the high spontaneous fission rates of these nuclides and heat generation by some Pu, Am, and Cm isotopes. Feasibility of the processing steps becomes more attainable if the time between discharge and reprocessing is 20 yr or longer.

Spray flame structure of rapeseed biodiesel and Jet-A1 fuel

The spray combustion characteristics of rapeseed methyl esters (RME) were compared to Jet-A1 fuel using a gas turbine type combustor. The swirling spray flames for both fuels were established at a constant power output of 6 kW. The main swirling air flow was preheated to 350 C prior to coaxially enveloping the airblast-atomized liquid fuel spray at atmospheric pressure. Investigation of the fundamental spray combustion was performed via measurements of the fuel droplet sizes and velocities, gas phase flow fields and flame reaction zones. The spray flame droplets and flow fields in the combustors were characterised using phase Doppler anemometry (PDA) and particle imaging velocimetry (PIV) respectively. Flame chemiluminescence imaging was employed to identify the flame reaction zones. The highest droplet concentration zone extends along a 30 angle from the symmetry axis, inside the flame zone. Only small droplets(<17 μ) (<17 μm)are found around the centreline region, while larger droplets are found at the edge of the spray outside the flame reaction zone. RME exhibits spray characteristics similar to Jet-A1 but with droplet concentration and volume fluxes four times higher, consistent with the expected longer droplet evaporation timescale. The flow field characteristics for both RME and Jet-A1 spray flames are very similar despite the significantly different visible characteristics of the flame reaction zones. © 2013 Elsevier Ltd. All rights reserved.

A screening study on persistent bioaccumulation toxins (PBT) in fuel combustion soot

Persistent bioaccumulative toxins (PBTs) are organic substances that are persistent, bioaccumulative and can cause severe toxic effects (e.g. potential oncogens, mutagenic, endocrine disrupters) to human health or environment which are the ones that need special attention. PBT chemicals could be released to the environment from several types of sources and are ubiquitous in environment. However, fast and efficiency monitoring and assessment methods to investigate PBTs in environment are still lacking. In this study, a cleaning-up procedure of analyzing PBTs in fuels combustion soot was developed and its performance was assessed through comparing the chromatograms of crude extracts with their cleaned extracts after the cleaning-up procedure. The results showed that polycyclic aromatic compounds (PACs) were the main components in fuel combustion soot and the clean-up procedure developed in this paper can be well used as the method of analyzing PBTs in fuels combustion soot.

Synthesis of novel P-ketimine bidentate ferrocenyl ligands with central and planar chirality and comparsion in the catalytic activity between P-ketimine and P-aldimine

A series of novel ferrocenylphosphine-ketimine ligands 6 were prepared by reaction of (R,S-p)-PPFNH2-R or (S,S-p)-PPFNH2 with a variety of m-substituted acetophenones. A different catalytic activity was observed between ferrocenylphosphine-ketimine ligands and corresponding aldimine ligands. The efficiency and diastereomeric impact of these ferrocenylphosphine-ketimine ligands in Pd-catalyzed asymmetric allylic alkylation were first investigated, and higher enantioselectivity of over 98% e.e. with 95% yield was obtained by the use of ferrocenylphosphine-ketimine ligands. However, in Rh-catalyzed asymmetric hydrosilylation of aryl ketones, only 42% e.e. was obtained by the use of ferrocenylphosphine-ketimine ligands compared to 90% e.e. with the use of aldimine ligands. (C) 2003 Elsevier Ltd. All rights reserved.

SYNTHESIS AND PHOTOCHROMISM IN SOLUTION OF PHENOXYNAPHTHACENEQUINONE DERIVATIVES

Two new phenoxynaphthacenequinone derivatives, 6-[4-(2-(4-hydroxyphenyl)isopropyl)phenoxy] -5,12-naphthacenequinone (7) and 6-[4-(potassium sulfophenylazo)phenoxy]-5,12-naphthacenequinone (8), were synthesized, and their photochromism in solution was investigated and compared with that of 6-phenoxy-5,12-naphthacenequinone (1). On the basis of the spectral data and the selective irreversible reaction of ammonia with the colored phenoxy-ana-naphthacenequinone, the concentrations of the ana forms at the photostationary state (PSS), achieved by 365 nm UV irradiation, and the molar extinction coefficients of the pure ana forms at 481-482 nm of compounds 1, 7 and 8 in dimethylsulfoxide (DMSO) were found to be 83 mol.% and 1.70x10(4) mol(-1) dm(3) cm(-1), 82 mol.% and 1.62x10(4) mol(-1) dm(3) cm(-1) and 16 mol.% and approximately 1.34x10(4) mol(-1) dm(3) cm(-1) respectively; the absorption spectra of the colored ana forms of 7 and 1 in DMSO were estimated; the rate;constants of photoconversion induced by 365 nm light were obtained. The results show the strong effect of the structure of the phenoxynaphthacenequinones on their photochromism in solution. In addition to DMSO solution, compound 7 exhibited normal photochromism in toluene, benzene, chloroform and a DMSO-ethanol mixed solvent, but not in dimethylformamide (DMF) in which a photoinduced reaction occurred between 7 and DMF or impurities.

Modeling of a compact plate-fin reformer for methanol steam reforming in fuel cell systems

The characteristics of a compact plate-fin reformer (PFR) which integrates endothermic and exothermic reactions into one unit have been investigated by experiment as well as by numerical simulation. One reforming chamber was integrated with two vaporization chambers and two combustion chambers to constitute a single unit of PFR. In the PFR, which is based on a plate-fin beat exchanger, catalytic combustion of the reforming gas is used to simulate the fuel cell anode off gas (AOG) which supplies the necessary heat for the methanol steam reforming. Temperature distributions in all chambers and composition distribution in reforming chamber have been studied, and the effect of the ratio of H2O/CH3OH on the performance of the PFR has also been investigated. A model of the PFR was derived using a three-dimensional numerical model for a cross-current flow arrangement. Theoretical predictions of the temperature distributions in the PFR were in good agreement with experimental values. In addition, the numerical model was able to accurately predict the methanol conversion and the reformate composition in reforming chamber. © 2005 Elsevier B.V. All rights reserved.

Size-controllable synthesis of monodispersed SnO2 nanoparticles and application in electrocatalysts

Size-controllable tin oxide nanoparticles are prepared by heating ethylene glycol solutions containing SnCl2 at atmospheric pressure. The particles were characterized by means of transmission electron microscopic (TEM), X-ray diffraction (XRD) studies. TEM micrographs show that the obtained material are spherical nanoparticles, the size and size distribution of which depends on the initial experimental conditions of pH value, reaction time, water concentration, and tin precursor concentration. The XRD pattern result shows that the obtained powder is SnO2 with tetragonal crystalline structure. On the basis of UV/vis and FTIR characterization, the formation mechanism of SnO2 nanoparticles is deduced. Moreover, the SnO2 nanoparticles were employed to synthesize carbon-supported PtSnO2 catalyst, and it exhibits surprisingly high promoting catalytic activity for ethanol electrooxidation.

Analysis of the mechanism and regulation of lactose transport and metabolism in Clostridium acetobutylicum ATCC 824.

Although the acetone-butanol-ethanol (ABE) fermentation of Clostridium acetobutylicum is currently uneconomic, the ability of the bacterium to metabolise a wide range of carbohydrates offers the potential for revival based on the use of cheap, low grade substrates. We have investigated the uptake and metabolism of lactose, the major sugar in industrial whey waste, by C. acetobutylicum ATCC 824. Lactose is taken up via a phosphoenolpyruvate (PEP)-dependent phosphotransferase system (PTS) comprising both soluble and membrane-associated components, and the resulting phosphorylated derivative is hydrolysed by a phospho--galactosidase. These activities are induced during growth on lactose, but are absent in glucose-grown cells. Analysis of the C. acetobutylicum genome sequence identified a gene system, lacRFEG, encoding a transcriptional regulator of the DeoR family, IIA and IICB components of a lactose PTS, and phospho--galactosidase. During growth in medium containing both glucose and lactose, C. acetobutylicum exhibited a classical diauxic growth, and the lac operon was not expressed until glucose was exhausted from the medium. The presence upstream of lacR of a potential catabolite responsive element (cre) encompassing the transcriptional start site is indicative of the mechanism of carbon catabolite repression characteristic of low-GC Gram-positive bacteria. A pathway for the uptake and metabolism of lactose by this industrially important organism is proposed.