Nitrogen removal from sludge digester liquids by nitrification/denitrification or partial nitritation/anammox: environmental and economical considerations

In wastewater treatment plants with anaerobic sludge digestion, 15-20% of the nitrogen load is recirculated to the main stream with the return liquors from dewatering. Separate treatment of this ammonium-rich digester supernatant significantly reduces the nitrogen load of the activated sludge system. Two biological applications are considered for nitrogen elimination: (i) classical autotrophic nitrification/heterotrophic denitrification and (ii) partial nitritation/autotrophic anaerobic ammonium oxidation (anammox). With both applications 85-90% nitrogen removal can be achieved, but there are considerable differences in terms of sustainability and costs. The final gaseous products for heterotrophic denitrification are generally not measured and are assumed to be nitrogen gas (N-2). However, significant nitrous oxide (N2O) production can occur at elevated nitrite concentrations in the reactor. Denitrification via nitrite instead of nitrate has been promoted in recent years in order to reduce the oxygen and the organic carbon requirements. Obviously this achievement turns out to be rather disadvantageous from an overall environmental point of view. On the other hand no unfavorable intermediates are emitted during anaerobic ammonium oxidation. A cost estimate for both applications demonstrates that partial nitritation/anammox is also more economical than classical nitrification/denitrification. Therefore autotrophic nitrogen elimination should be used in future to treat ammonium-rich sludge liquors.

Characterizing the physical and chemical properties of a vermicompost filter bed

Vermicompost filtration is a new on-site waste treatment system. Consequently, little is known about the filter medium properties. The aim of this preliminary study was to quantify physical and compositional properties of vermicompost filter beds that had been used to treat domestic solid organic waste and wastewater. This paper presents the trials performed on pilot-scale reactors filled with vermicompost from a full-scale vermicompost filtration system. Household solid organic waste and raw wastewater at the rate of 130 L/m(2)/d was applied to the reactor bed surface over a four-month period. It was found that fresh casts laid on the bed surface had a BOD of 1290 mg/g VS while casts buried to a depth of 10 cm had a BOD of 605 mg/g VS. Below this depth there was little further biodegradation of earthworm casts despite cast ages of up to five years. Solid material in the reactor accounted for only 7-10% of the reactor volume. The total voidage comprised of large free-draining pores, which accounted for 15-20% of the reactor volume and 60-70% micropores, able to hold up water against gravity. It was shown that water could flow through the medium micropores and macropores following a wastewater application. The wastewater flow characteristics were modeled by a two-region model based on the Richards Equation, an equation used to describe porous spatially heterogeneous materials.

Concurrent microscopic observations and activity measurements of cellulose hydrolyzing and methanogenic populations during the batch anaerobic digestion of crystalline cellulose

This study compares process data with microscopic observations from an anaerobic digestion of organic particles. As the first part of the study, this article presents detailed observations of microbial biofilm architecture and structure in a 1.25-L batch digester where all particles are of an equal age. Microcrystalline cellulose was used as the sole carbon and energy source. The digestions were inoculated with either leachate from a 220-Lanaerobic municipal solid waste digester or strained rumen contents from a fistulated cow. The hydrolysis rate, when normalized by the amount of cellulose remaining in the reactor, was found to reach a constant value 1 day after inoculation with rumen fluid, and 3 days after inoculating with digester leachate. A constant value of a mass specific hydrolysis rate is argued to represent full colonization of the cellulose surface and first-order kinetics only apply after this point. Additionally, the first-order hydrolysis rate constant, once surfaces were saturated with biofilm, was found to be two times higher with a rumen inoculum, compared to a digester leachate inoculum. Images generated by fluorescence in situ hybridization (FISH) probing and confocal laser scanning microscopy show that the microbial communities involved in the anaerobic biodegradation process exist entirely within the biofilm. For the reactor conditions used in these experiments, the predominant methanogens exist in ball-shaped colonies within the biofilm. (C) 2005 Wiley Periodicals, Inc.

Structure of a cellulose degrading bacterial community during anaerobic digestion

It is widely accepted that cellulose is the rate-limiting substrate in the anaerobic digestion of organic solid wastes and that cellulose solubilisation is largely mediated by surface attached bacteria. However, little is known about the identity or the ecophysiology of cellulolytic microorganisms from landfills and anaerobic digesters. The aim of this study was to investigate an enriched cellulolytic microbial community from an anaerobic batch reactor. Chemical oxygen demand balancing was used to calculate the cellulose solubilisation rate and the degree of cellulose solubilisation. Fluorescence in situ hybridisation (FISH) was used to assess the relative abundance and physical location of three groups of bacteria belonging to the Clostridium lineage of the Firmicutes that have been implicated as the dominant cellulose degraders in this system. Quantitation of the relative abundance using FISH showed that there were changes in the microbial community structure throughout the digestion. However, comparison of these results to the process data reveals that these changes had no impact on the cellulose solubilisation in the reactor. The rate of cellulose solubilisation was approximately stable for much of the digestion despite changes in the cellulolytic population. The solubilisation rate appears to be most strongly affected by the rate of surface area colonisation and the biofilm architecture with the accepted model of first order kinetics due to surface area limitation applying only when the cellulose particles are fully covered with a thin layer of cells. (c) 2005 Wiley Periodicals, Inc.

Efficient and stable nitritation and denitritation of ammonium-rich sludge dewatering liquor using an SBR with continuous loading

Separate treatment of dewatering liquor from anaerobic sludge digestion significantly reduces the nitrogen load of the main stream and improves overall nitrogen elimination. Such ammonium-rich wastewater is particularly suited to be treated by high rate processes which achieve a rapid elimination of nitrogen with a minimal COD requirement. Processes whereby ammonium is oxidised to nitrite only (nitritation) followed by denitritation with carbon addition can achieve this. Nitrogen removal by nitritation/denitritation was optimised using a novel SBR operation with continuous dewatering liquor addition. Efficient and robust nitrogen elimination was obtained at a total hydraulic retention time of 1 day via the nitrite pathway. Around 85-90% nitrogen removal was achieved at an ammonium loading rate of 1.2 g NH4+-N m(-3) d(-1). Ethanol was used as electron donor for denitritation at a ratio of 2.2gCODg(-1) N removed. Conventional nitritation/denitritation with rapid addition of the dewatering liquor at the beginning of the cycle often resulted in considerable nitric oxide (NO) accumulation during the anoxic phase possibly leading to unstable denitritation. Some NO production was still observed in the novel continuous mode, but denitritation was never seriously affected. Thus, process stability can be increased and the high specific reaction rates as well as the continuous feeding result in decreased reactor size for full-scale operation. (c) 2006 Elsevier Ltd. All rights reserved.

Alquilação de tolueno com propeno, através de complexo ferro (II) ᵦ- diimina homogêneo e heterogeneizado em MCM-41, Al-MCM-41 e SBA-15

This work describes the synthesis and aplication of homogeneous and heterogenized iron catalysts in the alkylation reaction of toluene with propene, empolying experimental design. The homogenous complex was obtained trough the synthesis of the organic ligand folowed by the complexation of the iron(II) chloride. As to the heterogenized complexes, first were synthetized the inorganic supports (SBA-15, MCM-41 and Al-MCM-41). Then, it was synthetized the ligand again, that through funcionalization with chloropropyltrimethoxysilane (CPTMS), was anchored on the support previously calcinated. To these anchored ligands, was complexed the iron(II) chloride, previously solubilizated in tetrahydrofuran (THF). The organic ligand characterization was accomplished trough nuclear magnetic resonance (NMR) and Infrared spectroscopy (IV). The supports were characterized with x-ray diffraction (DRX), texture analysis with nitrogen adsorption/desorption (before and after the anchoring), termogravimetric analysis (TG) and infrared (IV). The metalic content was quantified trough the atomic absorption spectrophotometry (AAS). The complexes were tested in catalytic reactions emolying ethylaluminium sesquichloride (EASC) as co-catalyst in steel reactor, under mecanic stirring. The reaction conditions ranged from 4 to 36 ◦C, with many aluminum/iron ratios. The catalysts were actives in homogeneous and heterogenized ways. The homogenous catalytic complex showed a maximum turnover frequency (TOF) of 8.63 ×103 · h −1 , while, in some conditions, the anchored complexes showed better results, with TOF of until 8.08 ×103 · h −1 . Aditionally, it was possible to determine an equation, to the homogenous catalyst, that describes the product quantity in function of reacional temperature and aluminum/iron ratio.

Remoção de nitratos em água utilizando diferentes materiais e processos

The need to preserve the environment has led to the search for new materials for efficient disposal of chemical compounds that alter the stability of our natural resources. Among these resources, stands in first place the water, as a precious commodity and scarce, leading to the proper use and reuse. As a result, the World Health Organization has established maximum permissible values in drinking water, such as: 50 mg/L, 0, 1 mg/L and 0, 5 mg/L to at-3, at-2, NH 4, respectively. For these reasons, assesses the implementation of new materials and water treatment processes aiming at the removal of these compounds, such as alumina, in the form of powder or as a support for a catalytic system using inorganic membranes capable of supporting more severe conditions of temperature and pressure by opening new possibilities for applications of membrane reactors; and also for electrochemical treatments with doped diamond bobo electrodes (BDD) as anode and copper as cathode. For such purpose, was conducted the study of adsorption of nitrate in different times to assess the time required to achieve equilibrium by employing three commercial alumina called: acidic, basic and neutral alumina, with subsequent treatment only in the acidic alumina impregnating metals (PdCu/Al2O3) for the catalytic reaction. The materials were previously characterized by XRD, SEM techniques and ABET. Aluminas presented a considerable adsortive capacity of nitrate in the first thirty minutes, equivalent to 50% of removal reaching equilibrium in that time. After treatment, using alumina as catalyst for the reaction in batch reactor (Pd-Cu/Al2O3), the results were more favourable, totalling 64% reduction of ion NO3-at the end of three hours. On the other hand, the results for the catalytic reaction using the catalytic support Pd-Cu/TiO2 in membrane reactor proved to be low. -if, in this way, improve the conditions of catalytic system to optimize the process. Already, for the electrochemical tests using DDB1 electrodes as anode, and Cu, as cathode, there was a fairly significant nitrate reduction, approximately 80% of ion removal during three hours and cost viable applications.

Reator de leito estruturado com recirculação submetido à aeração intermitente no tratamento de esgoto sanitário

The release of nitrogen compounds in water bodies can result in many environmental problems, so treat wastewater, such as sewage in order to remove not only organic matter but also nitrogen has been studied a few decades. From the above, the objective of this study was to evaluate the performance of a structured bed reactor, continuous flow, with recirculation, in removing organic matter and nitrogen present in wastewater under different cycles of intermittent aeration (AI) and to evaluate the influence of these cycles in the development of nitrifying bacteria (Oxidizing Bacteria Ammonia - BOA and Bacteria Oxidizing Nitrite - BON) and denitrifying (DESN) adhered (Support Material - MS) and suspension (Effluent - EF and sludge - LD). The reactor used has usable volume of 9.4 L. As support materials (MS) polyurethane foam was used, cut and fixed in PVC rods. 3 were worked aeration phases (AE) and non-aeration (AN) at different stage: Stage 1 (4 h EA / AN 2H); Stage 2 (2H EA / AN 1 h) and Phase 3 (2H EA / AN 2 h). During all hydraulic detention time phases was kept at 16 h and the effluent recirculated at a rate of 3 times the inflow. Were analyzed: pH, total alkalinity, temperature, chemical oxygen demand (COD), Biochemical Oxygen Demand (BOD), nitrogen Kjeldhl Total (NKT), ammonia-N-N-NH4+, nitrito-N-NO2+andnitrato-NO3-. The concentration of BOA, BON and DESN was determined using the number More Provável.gSSV-1 (NMP.gSSV-1). In phase 1 the percentage removal NTK N-NH4+ and NT was 76±10%, 70±21% and 67±10% respectively. In Phase 2 80±15% of removel NKT, 86±15% of N-NH4+ e 68±9% of removel NT e na Fase 3 de 58±20%, 72±28% and 41±6% of NKT, N-NH4+ of NT, respectively. The denitrification efficiency in stage 3 was over 70%, indicating that occurred in the reactor the process of simultaneous nitrification and denitrification (NDS). DQOT the removal percentages were 88 ± 4% in Phase 1, 94 ± 7 in Phase 2 and 90± 11% in Phase 3. The multivariate ANOVA applied to NMP.gSSV-1, it indicated that there was significant (F: 20,2, p <0,01) between the analyzed concentration of organisms AI in different cycles, but the differences between NMP.gSSV-1 depends not only isolated factors but of which means, and phase groups being analysis. From the results it is concluded that the working system is efficient in terms of nitrogen removal and organic matter, and that the stage with the highest availability of Dissolved Oxygen (DO) and C/N ratio (Step 2), was the one obtained the lower concentrations of organic matter effluents and N-NH4+. Hinted that there was a significant difference between the concentration (NMP.100mL-1) of the analyzed organizations (BOA, BON and DESN), but this difference does not depend on factors alone but of which means (MS, EF or LD), stages (1, 2 or 3) and groups (BOA, BON and DESN) is being considered.

Produção de biogás a partir da co-digestão de resíduos da geração de energia

Aplicações de microalgas tem tornado esses micro-organismos importantes em pesquisas com fins tanto comerciais como energéticos. A biofixação de CO2 por microalgas é vista como uma forma economicamente viável e ambientalmente sustentável para mitigar as emissões de CO2 e geração de biomassa para obtenção de bioprodutos de alto valor agregado como os biocombustíveis. Na digestão anaeróbia da biomassa de microalgas a adição de um cosubstrato rico em carbono pode facilitar o processo de produção de biogás. O glicerol possui alta concentração de carbono orgânico e é solúvel em água. Neste sentido, a combinação de ambos os substratos pode solucionar um dos principais problemas para o processo de digestão, que reside no equilíbrio da razão (C/N). Co-digestão anaeróbia consiste na digestão anaeróbia de uma mistura de dois ou mais substratos com composições complementares. O objetivo do estudo foi avaliar a geração de biogás através da co-digestão anaeróbia de biomassa de Spirulina sp. LEB 18 e glicerol bruto. Para a realização do estudo foram construídos e operados sete biorreatores com volume útil de 1,5 L, alimentados com 5, 6, 10, 15 e 20 g.L -1 da mistura de biomassa de Spirulina e glicerol. A adição de diferentes quantidades de glicerol (5 e 10 g.L -1 ) foi utilizada como um suplemento na digestão anaeróbia em sistema de batelada. A razão C/N variou de 3,3×103 a 23,7. Os ensaios foram realizados a 35 °C, em reatores equipados com sistema de coleta de gás, alimentação e retirada do efluente líquido, operados em batelada sequencial. O efluente líquido dos reatores foi analisado quanto ao pH, nitrogênio amoniacal e alcalinidade. O volume de biogás produzido diariamente foi medido em gasômetro de frasco invertido. Em todos os ensaios, os valores médios de pH variaram de 7,0 a 7,3 e nitrogênio amoniacal de 62,02 a 1100,99 mg.L-1 . A alcalinidade do efluente variou entre 1133,37 e 3578,98 mg.L-1 CaCO3. Em todos os ensaios com adição de glicerol houve incremento na produção específica de biogás (0,16 – 0,24 d -1 ) quando comparado ao ensaio em que somente biomassa microalgal era alimentada no processo (0,03 L.d-1 ), demonstrando ser esta uma alternativa interessante para a produção de biocombustível e concomitante agregação de valor ao glicerol residual da produção de biodiesel.

Dinâmica do fósforo em cultivo heterotrófico e produção de compostos celulares por cianobactéria integrado a biorrefinarias agroindustriais

O objetivo desta tese foi avaliar a dinâmica do fósforo em cultivo heterotrófico e produção de compostos celulares por Aphanothece microscopica Nägeli visando avaliar a perspectiva de implementação de uma biorrefinaria microalgal. Desta forma, foi avaliado o comportamento do micro-organismo em estudo no cultivo heterotrófico, utilizando como meio de cultivo o efluente de laticínios. O trabalho foi desenvolvido em 3 etapas. Em um primeiro momento foi avaliada a influência da temperatura (20 e 30°C) e os valores máximos e mínimos de nutrientes, em especial do fósforo dissolvido reativo (PDR), disponíveis no efluente de laticínio, na remoção de nutrientes. Os resultados demonstraram que a concentração inicial de fósforo dissolvido e a temperatura exerceram influência no crescimento celular e na eficiência de remoção de nutrientes. Em termos de otimização de processo os cultivos conduzidos a 20°C e maiores concentrações de PDR (5,5 mg.L-1 ) no efluente de laticínio, foram os mais eficientes na conversão de poluentes em biomassa e remoção de nutrientes. A segunda etapa foi desenvolvida com o objetivo de avaliar a dinâmica de distribuição de fósforo na fase líquida e sólida do reator heterotrófico, quando o efluente de laticínio foi tratado pela Aphanothece microscopica Nägeli, a 20°C e nas máximas concentrações de fósforo dissolvido encontradas no efluente. Foi demonstrado que as formas fosforadas na fase líquida do reator se caracterizam pela predominância da fração dissolvida em comparação à particulada e por apresentar como fração predominante a de fósforo orgânico. No que se refere à fase sólida, ficou demonstrado que a Aphanothece microscopica Nägeli, quando cultivada heterotroficamente apresenta 3,8 vezes mais fósforo que o requerido para o crescimento celular. Ficando demonstrado ainda que a remoção biológica de fósforo por Aphanothece microscopica Nägeli pode resultar em substanciais aportes financeiros para as estações de tratamento de efluentes. Uma terceira etapa foi desenvolvida, a qual teve como objetivo avaliar a estimativa de produção de compostos celulares por Aphanothece microscopica Nägeli, a partir do efluente de laticínio, bem como o efeito da redução de temperatura de cultivo no teor de lipídios , no momento em que é obtida a máxima concentração deste componente celular, nas condições otimizadas.Foi obtido na fase logarítmica de crescimento, concentrações de 41,8 % de proteinas, carboidratos 28,5 %, lipídios 10,4 % e minerais 10,8 %. O maior teor de lipídio registrado a 20°C correspondeu a biomassa analisada na fase logarítmica.Com a redução da temperatura para 5°C por um período de 30 h é possível obter concentrações de lipídios 2,4 vezes superior ao registrado na fase logarítmica a 20 °C. No entanto, não foram indicadas diferenças significativas (p≤0,05) em função da temperatura entre as concentrações de lipídios obtidas para a biomassa a 10°C em 40 h. O perfil de ácidos graxos da biomassa gerada a 20°C, apresentou como ácidos graxos majoritários, os ácidos graxos: palmítico, oléico, γ-linolênico, palmitoleico e esteárico, resultando um aumento na concentração de ácidos graxos saturados as espensa dos insaturados, quando a temperatura é reduzida. Em paralelo,um reator heterotrófico descontinuo foi definido, ficando demonstrado que a extrapolação da operação em batelada para contínua requer um biorreator heterotrófico com volume útil de trabalho de 240,51 m 3 , permitindo tratar 950 m3 diários de efluente, gerando 11,8 kg.d-1 de biomassa útil para produção de compostos celulares por Aphanothece microscopica Nägeli, visando à simultânea remoção de matéria orgânica, nitrogênio total e fósforo total, gerando insumos que podem suportar a implementação de uma biorrefinaria microalgal.

Eliminação/valorização de resíduos de frutas (kiwi) por digestão anaeróbia

Este estudo tem como objetivo a valorização económica de resíduos agroindustriais, nomeadamente resíduos de kiwi, por digestão anaeróbia de forma a otimizar a produção de biogás e a sua qualidade (% CH4). Trata-se de uma pesquisa experimental que consistiu na avaliação da produção de biogás usando diferentes proporções de substrato e inóculo, quatro valores distintos para a razão C:N, inóculo de diferentes digestores e colheita do inóculo em épocas distintas do ano. Os ensaios foram desenvolvidos num reator batch em condições mesofílicas, sendo o processo acompanhado por monitorização dos parâmetros: pH, Alcalinidade, Ácidos Gordos Voláteis (AGV), Sólidos Totais (ST), Sólidos Voláteis (SV), Carência Química de Oxigénio (CQO) e Carbono. Para a totalidade dos ensaios, o valor de pH no reator praticamente não apresentou variação, mantendo-se em torno de 7,0; a alcalinidade do meio, 1500 mg CaCO3/L, revelou-se adequada uma vez que no final do processo de DA a concentração de AGV (400-600 mg/L), nunca excede os valores considerados críticos. Os resultados obtidos apresentam valores interessantes para um número considerável de ensaios. Das 10 experiências realizadas, em duas foram obtidos resultados muito significativos em relação à literatura; o ensaio com 1% de substrato (experiência 2) registou uma produção de biogás de 1628 L/kg SV com uma %CH4 de 57% e o biogás de maior qualidade, 85% de metano, foi obtido no ensaio com 5% de resíduo de kiwi (experiência 10). As experiências em que se avaliou o efeito da razão C:N foram as menos produtivas, possivelmente devido à inibição da atividade da população microbiana pelo KNO3. A qualidade do inóculo revelou-se determinante num conjunto de ensaios, nomeadamente quando a sua colheita foi realizada no inverno, com o digestor a apresentar temperaturas bastante baixas. De acordo com os valores mais favoráveis para a produção de biogás, por tonelada de resíduo de kiwi poderá ser obtido um valor monetário bruto de 102 €, resolvendo-se um problema de eliminação deste resíduo, com valorização energética simultaneamente.

Degradação do PMMA através da reação despolimerização uitlizando catalisadores de óxidos mistos

In this work, mixed oxides were synthesized by two methods: polymeric precursor and gel-combustion. The oxides, Niquelate of Lanthanum, Cobaltate of Lanthanum and Cuprate of Lanthanum were synthesized by the polymeric precursor method, and treated at 300 º C for 2 hours, calcined at 800 º C for 6h in air atmosphere. In gel-combustion method were produced and oxides using urea and citric acid as fuel, forming for each fuel the following oxides Ferrate of Lanthanum, Cobaltato of Lanthanum and Ferrato of Cobalt and Lanthanum, which were submitted to the combustion process assisted by microwave power maximum of 10min. The samples were characterized by: thermogravimetric analysis, X-ray diffraction; fisisorção of N2 (BET method) and scanning electron microscopy. The reactions catalytic of depolymerization of poly (methyl methacrylate), were performed in a reactor of silica, with catalytic and heating system equipped with a data acquisition system and the gas chromatograph. For the catalysts synthesized using the polymeric precursor method, the cuprate of lanthanum was best for the depolymerization of the recycled polymer, obtaining 100% conversion in less time 554 (min), and the pure polymer, was the Niquelate of Lanthanum, with 100% conversion in less time 314 (min). By gel-combustion method using urea as fuel which was the best result obtained Ferrate of Lanthanum for the pure polymer with 100% conversion in less time 657 (min), and the recycled polymer was Cobaltate of Lanthanum with 100 % conversion in less time 779 (min). And using citric acid to obtain the best result for the pure polymer, was Ferrate of Lanthanum with 100% conversion in less time 821 (min and) for the recycled polymer, was Ferrate of Lanthanum with 98.28% conversion in less time 635 (min)

Síntese e caracterização de catalisadores de LaNiO3 não suportados e suportados em Al2O3 e ZrO2 para a reforma a vapor do metano

Ionic oxides with ABO3 structure, where A represents a rare earth element or an alkaline metal and B is a transition metal from group VIII of the periodic table are potential catalysts for oxidation and good candidates for steam reforming reaction. Different methods have been considered for the synthesis of the oxide materials with perovskite structure to produce a high homogeneous material with low amount of impurities and low calcination temperatures. In the current work, oxides with the LaNiO3 formula had been synthesized using the method of the polymeric precursors. The thermal treatment of the materials took place at 300 ºC for 2h. The material supported in alumina and/or zirconia was calcined at 800 ºC temperature for 4h. The samples had been characterized by the following techniques: thermogravimetry; infrared spectroscopy; X-ray diffraction; specific surface area; distribution of particle size; scanning electron microscopy and thermo-programmed reduction. The steam reforming reaction was carried out in a pilot plant using reducing atmosphere in the reactor with a mixture of 10% H2-Argon, a mass about 5g of catalyst, flowing at 50 mL.min-1. The temperature range used was 50 - 1000 oC with a heating rate of 10 oC.min-1. A thermal conductivity detector was used to analyze the gas after the water trapping, in order to permit to quantify the consumption of hydrogen for the lanthanum nickelates (LaNiO3). The results showed that lanthanum nickelate were more efficient when supported in alumina than when supported in zirconia. It was observed that the methane conversion was approximately 100% and the selectivity to hydrogen was about 70%. In all cases were verified low selectivity to CO and CO2

Effect of pH and temperature on the carbonate promoted dissolution of sodium meta-autunite

Release of uranium from Na-autunite, an artificial mineral created as a result of polyphosphate injection in the subsurface at the DOE Hanford Site, takes place during slow dissolution of the mineral structure. Stability information of the uranyl-phosphate phases is limited to conditions involving pH, temperature, and a few aqueous organic materials. The carbonate ion, which creates very strong complexes with uranium, is the predominant ion in the groundwater composition. The polyphosphate technology with the formation of autunite was identified as the most feasible remediation strategy to sequester uranium in contaminated groundwater and soil in situ. The objectives of the experimental work were (i) to quantify the effect of bicarbonate on the stability of synthetic sodium meta-autunite created as a result of uranium stabilization through polyphosphate injection, (ii) calculate the kinetic rate law parameters of the uranium release from Na-autunite during dissolution, and (iii) to compare the process parameters with those obtained for natural calcium meta-autunite. Experiments were conducted using SPTF apparatus, which consists of syringe pumps for controlling flow rate, Teflon reactors and a heating/cooling system. 0.25 grams of synthetic Na-autunite was placed in the reactor and buffer solutions with varying bicarbonate concentrations (0.0005 to 0.003 M) at different pH (6 - 11) were pumped through the reactors. Experiments were conducted at four different temperatures in the range of 5 - 60oC. It was concluded that the rate of release of uranium from synthetic Na-autunite is directly correlated to the bicarbonate concentration. The rate of release of uranium increased from 1.90 x 10-12 at pH 6 to 2.64 x 10-10 (mol m-2 s-1) at pH 11 at 23oC over the bicarbonate concentration range tested. The activation energy values were invariant with the change in the bicarbonate concentration; however, pH is shown to influence the activation energy values. Uranyl hydroxides and uranyl carbonates complexes helped accelerate the dissolution of autunite mineral.

Smantellamento di un reattore di potenza gas-grafite di I generazione: metodologie e tecnologie di rimozione della grafite e smantellamento del nocciolo

Il presente lavoro di tesi ha riguardato lo studio dello smantellamento di un reattore gas grafite di potenza di I Gen. L’indagine è stata focalizzata in particolare al recupero della grafite irraggiata che ne costituisce il core. Viene presentata una descrizione referenziata del reattore e dei suoi componenti per mettere in evidenza la particolare architettura e le specifiche problematiche ad essa correlate. A valle di un’indagine sulle esperienze internazionali in merito al decommissioning e allo smantellamento di questi tipi di reattori, si forniscono una possibile sequenza di accesso alla cavità del reattore e una procedura per il suo smantellamento; si descrivono sommariamente le tecnologie di taglio e di handling, attualmente allo stato dell’arte, considerate come più idonee a questo tipo di applicazione. Vengono descritte le principali criticità della grafite nuclear grade ed illustrati i fenomeni caratteristici che ne determinano l’evoluzione nel reattore. Sulla base dei dati resi disponibili dalla Sogin S.p:A. e ricorrendo ai dati di letteratura per quelli non disponibili, è stato effettuato un assessment della grafite irraggiata costituente il nocciolo del reattore, rivolto in particolare a determinarne le caratteristiche meccaniche e la resistenza residua post-irraggiamento. Per valutare la possibilità di prelevare la grafite dal nocciolo è stato ipotizzato un dispositivo di presa che agganci per attrito i blocchi di grafite del moderatore attraverso il canale assiale. Infine è stata valutata la fattibilità di tale metodo attraverso una serie di simulazioni agli elementi finiti dirette a verificare la resistenza del blocco in varie condizioni di carico e vincolo. Come risultato si è dimostrata la fattibilità, almeno in via preliminare, del metodo proposto, determinando l’inviluppo di utilizzo del dispositivo di presa nonché la compatibilità del metodo proposto con le tecnologie di handling precedentemente individuate.