Chirped fibre Bragg grating based multiplexer and demultiplexer for DWDM applications

A multiplexer/demultiplexer for 100 GHz channel spacing based on chirped fibre Bragg gratings with different bandwidths and optical circulators is presented. The spectral characteristics, specifications and operation of these passive devices are described, showing its potential use in dense wavelength division multiplexing (DWDM) applications. © 2004 Elsevier Ltd. All rights reserved.

Generation and performance of localised surface plasmons utilising nano-scale structured multi-layered thin films deposited upon D-shaped optical fiber

A new generation of surface plasmonic optical fibre sensors is fabricated using multiple coatings deposited on a lapped section of a single mode fibre. Post-deposition UV laser irradiation using a phase mask produces a nano-scaled surface relief grating structure, resembling nano-wires. The overall length of the individual corrugations is approximately 14 μm with an average full width half maximum of 100 nm. Evidence is presented to show that these surface structures result from material compaction created by the silicon dioxide and germanium layers in the multi-layered coating and the surface topology is capable of supporting localised surface plasmons. The coating compaction induces a strain gradient into the D-shaped optical fibre that generates an asymmetric periodic refractive index profile which enhances the coupling of the light from the core of the fibre to plasmons on the surface of the coating. Experimental data are presented that show changes in spectral characteristics after UV processing and that the performance of the sensors increases from that of their pre-UV irradiation state. The enhanced performance is illustrated with regards to change in external refractive index and demonstrates high spectral sensitivities in gaseous and aqueous index regimes ranging up to 4000 nm/RIU for wavelength and 800 dB/RIU for intensity. The devices generate surface plasmons over a very large wavelength range, (visible to 2 μm) depending on the polarization state of the illuminating light. © 2013 SPIE.

Chirped fibre Bragg grating based multiplexer and demultiplexer for DWDM applications

A multiplexer/demultiplexer for 100 GHz channel spacing based on chirped fibre Bragg gratings with different bandwidths and optical circulators is presented. The spectral characteristics, specifications and operation of these passive devices are described, showing its potential use in DWDM applications.

Gratings in novel fibre geometry for applications in shape sensing

A long period grating (LPG) fabricated in progressive three-layered (PTL) fibre is described. The grating with a period of 391µm, had dual attenuation bands associated with a particular cladding mode. The dual attenuation bands have been experimentally characterised for their spectral sensitivity to bending, which resulted in the highest sensitivity to bending seen for this particular fibre and temperature. The spectral characteristics of the fibre have been modelled giving good agreement to the experimental data as well as showing that the attenuation bands are both associated with the second order HE/EH2,n cladding mode.

Soliton switching using cascaded nonlinear-optical loop mirrors

We demonstrate multiple-peaked switching in a nonlinear-optical loop mirror and present an experimental investigation of device cascading in the soliton regime based on a sequence of two independent nonlinear-optical loop mirrors. Cascading leads to an enhanced switching response with sharper switching edges, flattened peaks, and increased interpeak extinction ratios. We observe that pulses emerging from the cascade retain the sech2 temporal profile of a soliton with minimal degradation in the spectral characteristics.

Long period grating in multicore optical fiber:an ultra-sensitive vector bending sensor for low curvatures

Long period grating was UV inscribed into a multicore fiber consisting of 120 single mode cores. The multicore fiber that hosts the grating was fusion spliced into a single mode fiber at both ends. The splice creates a taper transition between the two types of fiber that produces a nonadiabatic mode evolution; this results in the illumination of all the modes in the multicore fiber. The spectral characteristics of this fiber device as a function of curvature were investigated. The device yielded a significant spectral sensitivity as high as 1.23 nm/m-1 and 3.57 dB/m-1 to the ultra-low curvature values from 0 to 1 m-1. This fiber device can also distinguish the orientation of curvature experienced by the fiber as the long period grating attenuation bands producing either a blue or red wavelength shift. The finite element method (FEM) model was used to investigate the modal behavior in multicore fiber and to predict the phase-matching curves of the long period grating inscribed into multicore fiber. © 2014 Optical Society of America.

Chemical sensor using Mach-Zehnder interferometer based on a pair of largely tilted fiber gratings

We propose an in-fiber Mach-Zehnder interferometer formed by a pair of largely tilted fiber gratings. The interference spectral characteristics have been investigated. The experimental results using this device as a chemical sensor have a sensitivity as high as 719nm/RIU. © 2012 OSA.

Development of New Structural Health Monitoring Techniques

During the past two decades, many researchers have developed methods for the detection of structural defects at the early stages to operate the aerospace vehicles safely and to reduce the operating costs. The Surface Response to Excitation (SuRE) method is one of these approaches developed at FIU to reduce the cost and size of the equipment. The SuRE method excites the surface at a series of frequencies and monitors the propagation characteristics of the generated waves. The amplitude of the waves reaching to any point on the surface varies with frequency; however, it remains consistent as long as the integrity and strain distribution on the part is consistent. These spectral characteristics change when cracks develop or the strain distribution changes. The SHM methods may be used for many applications, from the detection of loose screws to the monitoring of manufacturing operations. A scanning laser vibrometer was used in this study to investigate the characteristics of the spectral changes at different points on the parts. The study started with detecting a load on a plate and estimating its location. The modifications on the part with manufacturing operations were detected and the Part-Based Manufacturing Process Performance Monitoring (PbPPM) method was developed. Hardware was prepared to demonstrate the feasibility of the proposed methods in real time. Using low-cost piezoelectric elements and the non-contact scanning laser vibrometer successfully, the data was collected for the SuRE and PbPPM methods. Locational force, loose bolts and material loss could be easily detected by comparing the spectral characteristics of the arriving waves. On-line methods used fast computational methods for estimating the spectrum and detecting the changing operational conditions from sum of the squares of the variations. Neural networks classified the spectrums when the desktop – DSP combination was used. The results demonstrated the feasibility of the SuRE and PbPPM methods.

Development of New Structural Health Monitoring Techniques

During the past two decades, many researchers have developed methods for the detection of structural defects at the early stages to operate the aerospace vehicles safely and to reduce the operating costs. The Surface Response to Excitation (SuRE) method is one of these approaches developed at FIU to reduce the cost and size of the equipment. The SuRE method excites the surface at a series of frequencies and monitors the propagation characteristics of the generated waves. The amplitude of the waves reaching to any point on the surface varies with frequency; however, it remains consistent as long as the integrity and strain distribution on the part is consistent. These spectral characteristics change when cracks develop or the strain distribution changes. The SHM methods may be used for many applications, from the detection of loose screws to the monitoring of manufacturing operations. A scanning laser vibrometer was used in this study to investigate the characteristics of the spectral changes at different points on the parts. The study started with detecting a load on a plate and estimating its location. The modifications on the part with manufacturing operations were detected and the Part-Based Manufacturing Process Performance Monitoring (PbPPM) method was developed. Hardware was prepared to demonstrate the feasibility of the proposed methods in real time. Using low-cost piezoelectric elements and the non-contact scanning laser vibrometer successfully, the data was collected for the SuRE and PbPPM methods. Locational force, loose bolts and material loss could be easily detected by comparing the spectral characteristics of the arriving waves. On-line methods used fast computational methods for estimating the spectrum and detecting the changing operational conditions from sum of the squares of the variations. Neural networks classified the spectrums when the desktop – DSP combination was used. The results demonstrated the feasibility of the SuRE and PbPPM methods.

Silicon photonic device for wavelength sensing and monitoring

Over the last decade advances and innovations from Silicon Photonics technology were observed in the telecommunications and computing industries. This technology which employs Silicon as an optical medium, relies on current CMOS micro-electronics fabrication processes to enable medium scale integration of many nano-photonic devices to produce photonic integrated circuitry. ^ However, other fields of research such as optical sensor processing can benefit from silicon photonics technology, specially in sensors where the physical measurement is wavelength encoded. ^ In this research work, we present a design and application of a thermally tuned silicon photonic device as an optical sensor interrogator. ^ The main device is a micro-ring resonator filter of 10 μm of diameter. A photonic design toolkit was developed based on open source software from the research community. With those tools it was possible to estimate the resonance and spectral characteristics of the filter. From the obtained design parameters, a 7.8 × 3.8 mm optical chip was fabricated using standard micro-photonics techniques. In order to tune a ring resonance, Nichrome micro-heaters were fabricated on top of the device. Some fabricated devices were systematically characterized and their tuning response were determined. From measurements, a ring resonator with a free-spectral-range of 18.4 nm and with a bandwidth of 0.14 nm was obtained. Using just 5 mA it was possible to tune the device resonance up to 3 nm. ^ In order to apply our device as a sensor interrogator in this research, a model of wavelength estimation using time interval between peaks measurement technique was developed and simulations were carried out to assess its performance. To test the technique, an experiment using a Fiber Bragg grating optical sensor was set, and estimations of the wavelength shift of this sensor due to axial strains yield an error within 22 pm compared to measurements from spectrum analyzer. ^ Results from this study implies that signals from FBG sensors can be processed with good accuracy using a micro-ring device with the advantage of ts compact size, scalability and versatility. Additionally, the system also has additional applications such as processing optical wavelength shifts from integrated photonic sensors and to be able to track resonances from laser sources.^

Variability of marine climate on the North Icelandic Shelf in a 1357-year proxy archive based on growth increments in the bivalve Arctica islandica

A multicentennial and absolutely-dated shell-based chronology for the marine environment of the North Icelandic Shelf has been constructed using annual growth increments in the shell of the long-lived bivalve clam Arctica islandica. The region from which the shells were collected is close to the North Atlantic Polar Front and is highly sensitive to the varying influences of Atlantic and Arctic water masses. A strong common environmental signal is apparent in the increment widths, and although the correlations between the growth increment indices and regional sea surface temperatures are significant at the 95% confidence level, they are low (r ~ 0.2), indicating that a more complex combination of environmental forcings is driving growth. Remarkable longevities of individual animals are apparent in the increment-width series used in the chronology, with several animals having lifetimes in excess of 300 years and one, at 507 years, being the longest-lived non-colonial animal so far reported whose age at death can be accurately determined. The sample depth is at least three shells after AD 1175, and the time series has been extended back to AD 649 with a sample depth of one or two by the addition of two further series, thus providing a 1357-year archive of dated shell material. The statistical and spectral characteristics of the chronology are investigated by using two different methods of removing the age-related trend in shell growth. Comparison with other proxy archives from the same region reveals several similarities in variability on multidecadal timescales, particularly during the period surrounding the transition from the Medieval Climate Anomaly to the Little Ice Age.

Stable isotopes of benthic foraminifera from Site ODP 184-1146

We generated a high resolution (~8 ky) benthic record from a West Pacific marginal basin to investigate the detailed structure and spectral characteristics of deep water isotope fluctuations during the middle Miocene. The benthic record from ODP Site 1146 allows unprecedented resolution of the structure of the middle Miocene delta13C excursion, as well as tighter control on the chronology of climatic events. Spectral analysis of the variance in the delta18O and delta13C records from ODP Site 1146 reveals spectral power concentrated in the eccentricity band (400-, ~100-ky) over the time interval between 13 and 17 Ma. The amplitude evolution in the 400-ky band is strikingly similar to that of the long eccentricity in Laskar's solution. There is an abrupt switch to the obliquity band in the delta18O record at -14.9 Ma, suggesting a shift in the ocean/climate response to orbital forcing (from low latitude eccentricity to high latitude obliquity forcing). The obliquity signal is pervasive in the delta18O record until -13.9 Ma, when a sharp increase in delta18O values indicates a major climatic transition. Comparison of delta18O and delta13C profiles from DSDP Site 588 (SW Pacific Ocean), ODP Site 761 (E Indian Ocean) and ODP Site 1146 (South China Sea) reveals significantly cooler deep water in the NE Indian Ocean throughout the middle Miocene and a restricted deep water exchange between the Pacific Ocean and Indian Ocean.

Laser IInduced Liinear and Nonlliinear Optiicall Studiies on Certaiin Metall Halliides and Tartrate Crystalls ffor Photoniic Applliicatiions

Nonlinear optics is a broad field of research and technology that encompasses subject matter in the field of Physics, Chemistry, and Engineering. It is the branch of Optics that describes the behavior of light in nonlinear media, that is, media in which the dielectric polarization P responds nonlinearly to the electric field E of the light. This nonlinearity is typically only observed at very high light intensities. This area has applications in all optical and electro optical devices used for communication, optical storage and optical computing. Many nonlinear optical effects have proved to be versatile probes for understanding basic and applied problems. Nonlinear optical devices use nonlinear dependence of refractive index or absorption coefficient on the applied field. These nonlinear optical devices are passive devices and are referred to as intelligent or smart materials owing to the fact that the sensing, processing and activating functions required for optical processes are inherent to them which are otherwise separate in dynamic devices.The large interest in nonlinear optical crystalline materials has been motivated by their potential use in the fabrication of all-optical photonic devices. Transparent crystalline materials can exhibit different kinds of optical nonlinearities which are associated with a nonlinear polarization. The choice of the most suitable crystal material for a given application is often far from trivial; it should involve the consideration of many aspects. A high nonlinearity for frequency conversion of ultra-short pulses does not help if the interaction length is strongly limited by a large group velocity mismatch and the low damage threshold limits the applicable optical intensities. Also, it can be highly desirable to use a crystal material which can be critically phasematched at room temperature. Among the different types of nonlinear crystals, metal halides and tartrates have attracted due to their importance in photonics. Metal halides like lead halides have drawn attention because they exhibit interesting features from the stand point of the electron-lattice interaction .These materials are important for their luminescent properties. Tartrate single crystals show many interesting physical properties such as ferroelectric, piezoelectric, dielectric and optical characteristics. They are used for nonlinear optical devices based on their optical transmission characteristics. Among the several tartrate compounds, Strontium tartrate, Calcium tartrate and Cadmium tartrate have received greater attention on account of their ferroelectric, nonlinear optical and spectral characteristics. The present thesis reports the linear and nonlinear aspects of these crystals and their potential applications in the field of photonics.

On the quality of acoustical measures when evaluating fruits quality

International audience

Caracterização ambiental de bancos areno-lamosos nos campos petrolíferos de Macau e Serra (RN), como subsídio às medidas mitigadoras ao processo erosivo

On Rio Grande do Norte northern coast the process of sediment transport are intensely controlled by wind and sea (waves and currents) action, causing erosion and shoreline morphological instability. Due to the importance of such coastal zone it was realized the multi-spectral mapping and physical-chemical characterization of mudflats and mangroves aiming to support the mitigating actions related to the containment of the erosive process on the oil fields of Macau and Serra installed at the study area. The multi-spectral bands of 2000 and 2008 LANDSAT 5 TM images were submitted on the several digital processing steps and RGB color compositions integrating spectral bands and Principal Components. Such processing methodology was important to the mapping of different units on surface, together with field works. It was possible to make an analogy of the spectral characteristics of wetlands with vegetations areas (mangrove), showing the possibility to make a restoration of this area, contributing with the environmental monitoring of that ecosystem. The maps of several units were integrated in GIS environment at 1:60,000 scale, including the classification of features according to the presence or absence of vegetation cover. Thus, the strategy of methodology established that there are 10.13 km2 at least of sandy-muddy and of these approximately 0.89 km2 with the possibility to be used in a reforestation of typical flora of mangrove. The physical-chemical characterization showed areas with potential to introduce local species of mangrove and they had a pH above neutral with a mean of 8.4. The characteristic particle size is sand in the fine fractions, the high levels of carbonate, organic matter and major and trace element in general are concentrated where the sediment had the less particles size, showing the high correlation that those elements have with smaller particles of sediment. The application of that methodological strategy is relevant to the better understanding of features behavior and physical-chemical data of sediment samples collected on field allow the analysis of efficiency/capability of sandy-muddy to reforestation with local mangrove species for mitigation of the erosive action and coastal processes on the areas occupied by the oil industry