922 resultados para Solução arquitetural


Relevância:

20.00% 20.00%

Publicador:

Resumo:

O uso de cápsulas porosas para extração de solução do solo é interessante por ser um ensaio não-destrutivo. Entretanto, persistem dúvidas sobre a liberação de íons da própria cápsula, que podem contaminar a solução extraída. Foram realizados testes na Faculdade de Ciências Agronômicas/UNESP, Botucatu (SP), com o objetivo de verificar a liberação de Ca e de Mg por cápsulas porosas de porcelana. No primeiro, foram empregados quatro tratamentos: T1 - lavagem das cápsulas com água destilada, forçando sua passagem pelas cápsulas, utilizando uma bomba a vácuo; T2 - lavagem das cápsulas com HCl 0,1 mol L-1, forçando sua passagem pelas cápsulas, utilizando uma bomba a vácuo; T3 - lavagem das cápsulas com água destilada, sem vácuo, e T4 - lavagem das cápsulas com HCl 0,1 mol L-1, sem vácuo, em um tempo de imersão de 24 h (para T3 e T4). No segundo teste, as cápsulas tratadas com HCl 0,1 mol L-1 no primeiro teste foram lavadas com água destilada novamente e deixadas de molho em água destilada e deionizada durante 45 min. Após estes procedimentos, as cápsulas foram imersas em água destilada, tomando-se alícotas desta solução para determinação de pH e dos teores de Ca e Mg após contato com as cápsulas por 0; 0,5; 1,0; 2,0; 4,0 e 24 h. Cada tratamento teve quatro repetições. Não se observou liberação significativa de Ca e Mg das cápsulas porosas para a solução, quando foram preparadas utilizando-se da passagem de HCl 0,1 mol L-1 a vácuo e água destilada, e deixadas, a seguir, em água destilada e deionizada durante 4 h.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

The oil and petrochemical industry is responsable to generate a large amount of waste and wastewater. Among some efluents, is possible find the benzene, toluene, ethilbenze and isomers of xilenes compounds, known as BTEX. These compounds are very volatily, toxic for environment and potencially cancerigenous in man. Oxidative advanced processes, OAP, are unconventional waste treatment, wich may be apply on treatment and remotion this compounds. Fenton is a type of OAPs, wich uses the Fenton s reactant, hydrogen peroxide and ferrous salt, to promove the organic degradation. While the Photo-Fenton type uses the Fenton s reactant plus UV radiation (ultraviolet). These two types of OAP, according to literature, may be apply on BTEX complex system. This project consists on the consideration of the utilization of technologies Fenton and Photo-Fenton in aqueous solution in concentration of 100 ppm of BTEX, each, on simulation of condition near of petrochemical effluents. Different reactors were used for each type of OAP. For the analyticals results of amount of remotion were used the SPME technique (solid phase microextraction) for extraction in gaseous phase of these analytes and the gas chromatography/mass espectrometry The arrangement mechanical of Photo-Fenton system has been shown big loss by volatilization of these compounds. The Fenton system has been shown capable of degradate benzene and toluene compounds, with massic percentage of remotion near the 99%.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Polymer particles in the nanometer range are of fundamental interest today, especially when used as carrier systems in the controlled release of drugs, cosmetics and nutraceuticals, as well as in coating materials with magnetic properties. The main objective of the present study concerns the production of submicron particles of poly (methyl methacrylate) (PMMA) by crystallization of a polymer solution by thermally controlled cooling. In this work, PMMA solutions in ethanol and 1-propanol were prepared at different concentrations (1% to 5% by weight) and crystallized at different cooling rates (0.2 to 0.8 ° C / min) controlled linearly. Analysis of particle size distribution (DLS / CILAS) and scanning electron microscopy (SEM) were performed in order to evaluate the morphological characteristics of the produced particles. The results demonstrated that it is possible to obtain submicron polymer perfectly spherical particles using the technique discussed in this study. It was also observed that, depending on the cooling rate and the concentration of the polymer solution, it is possible to achieve high yield in the formation of submicron particles. In addition, preliminary tests were performed in order to verify the ability of this technique to form particulated carrier material with magnetic properties. The results showed that the developed technique can be an interesting alternative to obtain polymer particles with magnetic properties

Relevância:

20.00% 20.00%

Publicador:

Resumo:

O objetivo deste trabalho foi avaliar a dinâmica de nutrientes na solução do solo após a aplicação, via fertirrigação, de nitrogênio, fósforo e potássio a laranjeiras. O experimento foi realizado entre setembro de 2007 e outubro de 2009, em pomares de laranjeiras 'Valência' e 'Hamlin', enxertadas sobre citrumeleiro 'Swingle'. Foram avaliadas cinco doses de N, P2O5 e K2O (0, 25, 50, 100 e 200% da dose recomendada). A solução do solo foi extraída a 30 e 60 cm de profundidade, com o auxílio de extratores com cápsulas porosas. Foram realizadas 11 avaliações durante o período experimental, com as extrações iniciadas após 12 horas das fertirrigações. O aumento das doses reduziu o pH (pH~3,5, na maior dose), e aumentou a condutividade elétrica (CE~1,5 dS m-1, na maior dose) e os teores de NH4, NO3, P, K, Mn e Zn na solução do solo, nas duas profundidades amostradas. Nos meses com maior precipitação pluvial, houve perda potencial de nutrientes por lixiviação, pois maiores concentrações de NO3, K e B foram observadas à profundidade de 60 cm. A análise da solução do solo, obtida por extratores com cápsula de cerâmica porosa, pode ser considerada ferramenta auxiliar para monitorar e avaliar a disponibilidade de nutrientes às plantas.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Este trabalho foi conduzido com o objetivo de avaliar as características de crescimento e produção de quatro cultivares de gérbera de vaso fertirrigadas com duas soluções nutritivas. O experimento foi realizado em casa-de-vegetação, durante o período de maio a julho de 2006, na UNESP-FCA em Botucatu-SP. O delineamento experimental foi de blocos casualizados e constituído em esquema fatorial 4x2, sendo 4 cultivares de gérbera (Cherry, Golden Yellow, Salmon Rose e Orange) e 2 soluções nutritivas. As plantas foram conduzidas em vasos com volume de 1,3 L, preenchidos com substrato composto de 70% de casca de pinus fina e 30% de terra de subsolo. Avaliou-se o número de folhas e diâmetro de planta semanalmente durante o ciclo da cultura; área foliar e fitomassa seca ao final dos períodos vegetativo e reprodutivo; tempo necessário para a produção, número de inflorescências, diâmetro das inflorescências e hastes e altura de planta, no ponto de comercialização. As cultivares responderam de maneira diferenciada quanto às características de crescimento, Salmon Rose e Cherry apresentaram maior formação de parte aérea; Golden Yellow e Orange foram mais compactas. No ponto de comercialização, somente altura, diâmetro de inflorescência e haste apresentaram variação entre as cultivares. As duas soluções nutritivas foram eficientes para a produção de plantas de qualidade.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Relevância:

20.00% 20.00%

Publicador:

Resumo:

The literary critic Terry Eagleton obtained notoriety in academic circles when he was recognized intellectually for his bestselling book Literary Theory: An Introduction. In this book, the English author boldly proposes the end of literature and literary criticism. However, Eagleton proposed years before, in his book Criticism and Ideology (1976), a scientific system of analysis of literary texts, which seemed less radical, both in theory and in method, than in his later theoretical proposal. Based on this, the objective of this dissertation is to present the English literary critic´s initial method, explaining the reasons that led him to abandon his initial project - of develop a method of analysis of the literary text on a Marxist scientific perspective - and to propose, in the following years, in his most famous book and others, a revolutionary vision that would go beyond textual analysis and make literary texts have a practical intervention in society. Finally, we explain what would be his idea of revolutionary criticism

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Relevância:

20.00% 20.00%

Publicador:

Resumo:

In this work the organosilanes aminopropyltriethoxysilane, 3-mercaptopropyltryethoxisilane and n[-3-(trimetoxisilyl)propyl]ethylenetriamine, as well as tetraethylortosilicate (TEOS), were employed to produce, by sol-gel method, organofuncionalized silicon samples. The prepared samples were characterized by elementar analys by thermogravimetry and infrared spectroscopy. Those samples were employed to adsorb Cd2+, Pb2+, Ni2+ and Zn2+ from aqueous solutions (10, 20, 40, 60 and 80 mg L-1). In typical experiments, 50 mg of the organometrix was suspended in 20 mL of metal cation solutions at four different contact times: 30, 60, 90 and 120 minutes. The total amount of adsorbed cations were measured by atomic absorption spectrometry. To all investigated matrices, the following adsorption capacity was observed: Ni2+ > Zn2+ > Cd2+ > Pb2+. Such sequence is closely related with the cation radius, as well as the cation hardness

Relevância:

20.00% 20.00%

Publicador:

Resumo:

This study aimed to analyze the effect of a saline solution on growth and chemical composition of Atriplex nummularia, shrubby plant, absorbing salts used in the diet of animals and the management of water and saline soils. These plant seedlings were planted and grown in a reserved area at the Federal University of Rio Grande do Norte. The plantation was divided into two blocks, in which one of them was irrigated with saline solution with a concentration of 2840 mgL-1 of NaCl and the second group was irrigated with drinking water. After six months, the plants were collected, harvested and divided into three parts: leaf, thin and thick stem. Monthly, dimension measurements were carried out for cataloging the growth of Atriplex. Ion Chromatography (IC) and Optical Emission Spectroscopy Inductively Coupled Plasma (ICP-OES) were used to analyze the chemical composition of the partition plant parts. The results of these analyses revealed that an absorption process of anions and cations by Atriplex nummularia plant during its growth was achieved, in particular by a higher concentration of sodium and chloride ions. Scanning electron microscopy images showed and confirmed the presence of small crystals on the leaf surface. Electrical conductivity and pH measurements of the aerial parts of the plant were carried out and these results showed that the leaf is the plant part where there is a largest concentration of ions. In addition, measurements of specific surface were obtained from irrigated plants with saline solution, achieving higher surface area, in all cases. Plant dimensions obtained monthly showed that the plants irrigated with water grew 5% more than those plants irrigated with saline solution. Based on results obtained, Atriplex plant showed a higher potential to survive and adapt to environments (aquatic or geological) with high levels of salinity and this property can be used as a tool for removing salts/metals from industrial contaminated soils and effluents.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Combating pollution of soils is a challenge that has concerned researchers from different areas and motivated the search for technologies that aim the recovery of degraded soils. Literature shows numerous processes that have been proposed with the intent of remediating soils contaminated by oils and other by-products of the oil industry, considering that the processes available have, generally, high operating costs, this work proposes a costeffective alternative to the treatment of Diesel-contaminated soils. The washing solutions were prepared using water as aqueous phase, the saponified coconut oil (OCS) as surfactant and n-butanol as co-surfactant. In this study, the soil was characterized by physical and chemical analyses. The study of diesel desorption from the soil was held in bath, using hexane and washing solutions, which had 10 and 20 wt.% active matter (AM - co-surfactant/surfactants) respectively. The study of the influence of active matter concentration and temperature in bath agitated used an experimental planning. The experiment also developed a system of percolation in bed to wash the soil and studied the influence of the concentration of active substance and volume of washing solution using an experimental planning. The optimal times to achieve hexane extraction were 30 and 180 min, while the best results using a 10% AM was 60 min and using a 20% AM was 120 min. The results of the experimental planning on bath showed that the maximum diesel removal was obtained when at a 20 wt.% of AM and under 50 °C, removing 99.92% of the oil. As for experiments in the system of percolation soil bed, the maximum diesel removal was high when the volume of the washing solution was of 5 L and the concentration of 20% AM. This experiment concluded that the concentration of AM and the temperature were vital to bath experiments for diesel removal, while in the system of percolation soil bed only concentration of AM influenced the soil remediation

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Model-oriented strategies have been used to facilitate products customization in the software products lines (SPL) context and to generate the source code of these derived products through variability management. Most of these strategies use an UML (Unified Modeling Language)-based model specification. Despite its wide application, the UML-based model specification has some limitations such as the fact that it is essentially graphic, presents deficiencies regarding the precise description of the system architecture semantic representation, and generates a large model, thus hampering the visualization and comprehension of the system elements. In contrast, architecture description languages (ADLs) provide graphic and textual support for the structural representation of architectural elements, their constraints and interactions. This thesis introduces ArchSPL-MDD, a model-driven strategy in which models are specified and configured by using the LightPL-ACME ADL. Such strategy is associated to a generic process with systematic activities that enable to automatically generate customized source code from the product model. ArchSPLMDD strategy integrates aspect-oriented software development (AOSD), modeldriven development (MDD) and SPL, thus enabling the explicit modeling as well as the modularization of variabilities and crosscutting concerns. The process is instantiated by the ArchSPL-MDD tool, which supports the specification of domain models (the focus of the development) in LightPL-ACME. The ArchSPL-MDD uses the Ginga Digital TV middleware as case study. In order to evaluate the efficiency, applicability, expressiveness, and complexity of the ArchSPL-MDD strategy, a controlled experiment was carried out in order to evaluate and compare the ArchSPL-MDD tool with the GingaForAll tool, which instantiates the process that is part of the GingaForAll UML-based strategy. Both tools were used for configuring the products of Ginga SPL and generating the product source code

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Este artigo busca expor as críticas de Bernardo de Claraval às superfluidades humanas no texto da Apologia, especialmente aquelas referentes à arte arquitetural. em segundo lugar, procura analisar as implicações estéticas do ascetismo cisterciense e bernardiano. As críticas de Bernardo exercem uma influência decisiva na ornamentação e fazem nascer uma nova arquitetura.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Over the years the use of application frameworks designed for the View and Controller layers of MVC architectural pattern adapted to web applications has become very popular. These frameworks are classified into Actions Oriented and Components Oriented , according to the solution strategy adopted by the tools. The choice of such strategy leads the system architecture design to acquire non-functional characteristics caused by the way the framework influences the developer to implement the system. The components reusability is one of those characteristics and plays a very important role for development activities such as system evolution and maintenance. The work of this dissertation consists to analyze of how the reusability could be influenced by the Web frameworks usage. To accomplish this, small academic management applications were developed using the latest versions of Apache Struts and JavaServer Faces frameworks, the main representatives of Java plataform Web frameworks of. For this assessment was used a software quality model that associates internal attributes, which can be measured objectively, to the characteristics in question. These attributes and metrics defined for the model were based on some work related discussed in the document