(Table 1) Summary of basalt unit thickness, vesicularity, number of flow units, and average porosity at ODP Site 135-839

An inflatable drill-string packer was used at Site 839 to measure the bulk in-situ permeability within basalts cored in Hole 839B. The packer was inflated at two depths, 398.2 and 326.9 mbsf; all on-board information indicated that the packer mechanically closed off the borehole, although apparently the packer hydraulically sealed the borehole only at 398.2 mbsf. Two pulse tests were run at each depth, two constant-rate injection tests were run at the first set, and four were run at the second. Of these, only the constant-rate injection tests at the first set yielded a permeability, calculated as ranging from 1 to 5 * 10**-12 m**2. Pulse tests and constant-rate injection tests for the second set did not yield valid data. The measured permeability is an upper limit; if the packer leaked during the experiments, the basalt would be less permeable. In comparison, permeabilities measured at other Deep Sea Drilling Project and Ocean Drilling Program sites in pillow basalts and flows similar to those measured in Hole 839B are mainly about 10**-13 to 10**-14 m**2. Thus, if our results are valid, the basalts at Site 839 are more permeable than ocean-floor basalts investigated elsewhere. Based on other supporting evidence, we consider these results to be a valid measure of the permeability of the basalts. Temperature data and the geochemical and geotechnical properties of the drilled sediments all indicate that the site is strongly affected by fluid flow. The heat flow is very much less than expected in young oceanic basalts, probably a result of rapid fluid circulation through the crust. The geochemistry of pore fluids is similar to that of seawater, indicating seawater flow through the sediments, and sediments are uniformly underconsolidated for their burial depth, again indicating probable fluid flow. The basalts are highly vesicular. However, the vesicularity can only account for part of the average porosity measured on the neutron porosity well log; the remainder of the measured porosity is likely present as voids and fractures within and between thin-bedded basalts. Core samples, together with porosity, density, and resistivity well-log data show locations where the basalt section is thin bedded and probably has from 15% to 35% void and fracture porosity. Thus, the measured permeability seems reasonable with respect to the high measured porosity. Much of the fluid flow at Site 839 could be directed through highly porous and permeable zones within and between the basalt flows and in the sediment layer just above the basalt. Thus, the permeability measurements give an indication of where and how fluid flow may occur within the oceanic crust of the Lau Basin.

87Sr/86Sr ratios of middle Miocene to Pleistocene planktonic foraminifers from ODP Site 117-722 (Table 3)

Continuous magnetostratigraphy and biostratigraphy made it possible to construct a detailed late Neogene record of 87Sr/86Sr isotopic ratios of ocean water, as measured in the tests of planktonic foraminifers. Sediments recovered during Leg 117, in the western Arabian Sea, provide a continuous, high resolution sedimentary record from the early Miocene to present. The late Miocene to Recent is marked by rapidly increasing 87Sr/86Sr ratios in seawater, which results in a chronostratigraphical resolution varying from 0.2 Ma to 1.5 Ma. The 87Sr/86Sr seawater curve has a stepwise character similar to the one determined by DePaolo on Site 590B, in the Tasman Sea, and to the one determined by McKenzie on Site 653A, in the Mediterranean, confirming its use as a chronostratigraphic tool for this time span. Periods of rapid increase in the 87Sr/86Sr isotopic ratio of seawater are correlated with important changes in tectonic and climatic conditions. Experiments showed that bulk carbonate sediment samples have differing 87Sr/86Sr ratios from those of planktonic and benthic foraminifers from the same depth.

(Table 1) Boron concentration and d11B ratios of ODP Hole 130-803D

The pH of the surface ocean is a sensitive function of its alkalinity and total inorganic carbon concentration, properties which also control the partial pressure of atmospheric carbon dioxide (Broecker and Peng, 1982). Thus, an accurate proxy for past ocean pH could yield information about variations in atmospheric CO2. Recently, it has been suggested that the boron isotopic composition of foraminiferal tests depends on the pH of sea water as well as its isotopic composition (Vengosh et al., 1991, doi:10.1016/0016-7037(91)90139-V; Hemming and Hanson, 1992, doi:10.1016/0016-7037(92)90151-8). Here we present boron isotope and elemental data for sedimentary pore fluids and isotope data for bulk foraminiferal samples from a deep-sea sediment core. The composition of the pore waters implies that sea water boron concentrations and isotopic composition have been constant during the past 21 Myr, allowing us to reconstruct past ocean pH directly from the foraminiferal isotope data. We find that 21 Myr ago, surface ocean pH was only 7.4 ±0.2, but it then increased to 8.2 ±0.2 (roughly the present value) about 7.5 Myr ago. This is consistent with suggestions (Popp et al., 1989; Cerling, 1991; Arthur et al., 1991) that atmospheric CO2 concentrations may have been much higher 21 Myr ago than today.

Oxygen and carbon isotope ratios for six planktonic foraminifer species from different water depth, Ontong-Java Plateau, Pacific (Table 2)

Stable isotope analyses and scanning electron micrographs have been carried out on six planktonic forminifera species, Pulleniatina obliquiloculata, Globorotalia tumida, Sphaeroidinella dehiscens, Globigerinoides ruber, Globigerinoides sacculifer and Globigerinoides quadrilobatus from eleven box-cores taken at increasing depths in the equatorial Ontong-Java Plateau (Pacific). This allows us to describe the way dissolution affects the microstructures of the tests of the different species and to quantify the changes of isotopic composition. We may conclude that: 1) dissolution effects on test morphology and stable isotope compositions are species dependent, species with a similar habitat showing a similar trend; 2) the shallow water, thin-shelled species are the first to disappear: scanning electron microscope (SEM) work shows alteration of outer layers. Deep water, thick-shelled species are present in all samples: SEM work shows breakdown and disparition of inner layers; 3) for all species there is a similar trend towards increasing delta18O values with increasing water depths and increasing dissolution. This effect may be as high as 0.6 ? per thousand meters for Globorotalia tumida; 4) below the lysocline, around 3500 m, it appears that 13C/12C ratios slightly increase towards equilibrium values for thick shelled species: G. tumida, P. obliquiloculata and S. dehiscens. 14C dates and isotope stratigraphy of two box-cores show that all samples are recent in age, and exclude upward mixing of glacial deposits as an important factor.

Permeability tests by the Thiem method /

Mode of access: Internet.

(Table 1) Sample characteristics, test consolidations and calculated elastic parameters of ODP Sites 194-1193 and 194-1196

This study is based on rock mechanical tests of samples from platform carbonate strata to document their petrophysical properties and determine their potential for porosity loss by mechanical compaction. Sixteen core-plug samples, including eleven limestones and five dolostones, from Miocene carbonate platforms on the Marion Plateau, offshore northeast Australia, were tested at vertical effective stress, sigma1', of 0-70 MPa, as lateral strain was kept equal to zero. The samples were deposited as bioclastic facies in platform-top settings having paleo-water depths of <10-90 m. They were variably cemented with low-Mg calcite and five of the samples were dolomitized before burial to present depths of 39-635 m below sea floor with porosities of 8-46%. Ten samples tested under dry conditions had up to 0.22% strain at sigma1' = 50 MPa, whereas six samples tested saturated with brine, under drained conditions, had up to 0.33% strain. The yield strength was reached in five of the plugs. The measured strains show an overall positive correlation with porosity. Vp ranges from 3640 to 5660 m/s and Vs from 1840 to 3530 m/s. Poisson coefficient is 0.20-0.33 and Young's modulus at 30 MPa ranged between 5 and 40 GPa. Water saturated samples had lower shear moduli and slightly higher P- to S-wave velocity ratios. Creep at constant stress was observed only in samples affected by pore collapse, indicating propagation of microcracks. Although deposited as loose carbonate sand and mud, the studied carbonates acquired reef-like petrophysical properties by early calcite and dolomite cementation. The small strains observed experimentally at 50 MPa indicate that little mechanical compaction would occur at deeper burial. However, as these rocks are unlikely to preserve their present high porosities to 4-5 km depth, further porosity loss would proceed mainly by chemical compaction and cementation.

(Table 1) Comparison between bulk ICP-OES measurements and LA-ICP-MS analyses for Mg/Ca and Sr/Ca ratios of Globigerinoides sacculifer from ODP Hole 165-1000A

We constructed a high-resolution Mg/Ca record on the planktonic foraminifer Globigerinoides sacculifer in order to explore the change in sea surface temperature (SST) due to the shoaling of the Isthmus of Panama as well as the impact of secondary factors like diagenesis and large salinity fluctuations. The study covers the latest Miocene and the early Pliocene (5.6-3.9 Ma) and was combined with d18O to isolate changes in sea surface salinity (SSS). Before 4.5 Ma, SSTMg/Ca and SSS show moderate fluctuations, indicating a free exchange of surface ocean water masses between the Pacific and the Atlantic. The increase in d18O after 4.5 Ma represents increasing salinities in the Caribbean due to the progressive closure of the Panamanian Gateway. The increase in Mg/Ca toward values of maximum 7 mmol/mol suggests that secondary influences have played a significant role. Evidence of crystalline overgrowths on the foraminiferal tests in correlation with aragonite, Sr/Ca, and productivity cyclicities indicates a diagenetic overprint on the foraminiferal tests. Laser ablation inductively coupled plasma-mass spectrometry analyses, however, do not show significantly increased Mg/Ca ratios in the crystalline overgrowths, and neither do calculations based on pore water data conclusively result in significantly elevated Mg/Ca ratios in the crystalline overgrowths. Alternatively, the elevated Mg/Ca ratios might have been caused by salinity as the d18O record of Site 1000 has been interpreted to represent large fluctuations in SSS, and cultivating experiments have shown an increase in Mg/Ca with increasing salinity. We conclude that the Mg/Ca record <4.5 Ma can only reliably be considered for paleoceanographical purposes when the minimum values, not showing any evidence of secondary influences, are used, resulting in a warming of central Caribbean surface water masses after 4.5 Ma of ~2°C.

(Table 1) Grain size composition of surface sediments from the Barents Sea shelf

The surface layer of bottom sediments on the Barents Sea shelf has an irregular but generally very low abundance of diatoms. Tests of species belonging to present-day diatom flora were absent in nearly half of samples; their abundance was only a few shells per gram of dry sediment in 30% of the samples, it was up to 100 shells per gram in 9% of the samples, and was in thousands of shells per gram in only 13% of the samples. The lowest abundances of diatom shells were found in sediments of the eastern and northeastern parts of the sea owing to unfavorable sedimentation conditions and deficiency of dissolved silica in water. But distribution of diatom species on the surface of bottom sediments is strictly consistent with their present-day ranges. About 30% of the samples contained re-deposited Cretaceous and Paleogene diatoms indicating that bottom sediments have largely formed by scouring and re-deposition of underlying material.

(Table 2) Age determination of Florida Straits sediment cores

The waters passing through the Florida Straits today reflect both the western portion of the wind-driven subtropical gyre and the northward flow of the upper waters which cross the equator, compensating North Atlantic Deep Water export as part of the large-scale Atlantic meridional overturning circulation. It has been postulated from various lines of evidence that the overturning circulation was weaker during the Younger Dryas cold event of the last deglaciation. We show here that the contrast in the oxygen isotopic composition of benthic foraminiferal tests across the Florida Current is reduced during the Younger Dryas. This most likely reflects a decrease in the density gradient across the channel and a decrease in the vertical shear of the Florida Current. This reduced shear is consistent with the postulated reduction in the Atlantic meridional overturning circulation. We find that the onset of this change in density structure and flow at the start of the Younger Dryas is very abrupt, occurring in less than 70 years.

(Table 3) Mediterranean core-top d18O values for various planktonic foraminiferal species

A box model is presented to simulate changes in Mediterranean long-term average salinity and d18O over the past 20,000 years. Simulations are validated by comparison with observations. Sensitivity tests illustrate robustness with respect to the main assumptions and uncertainties. The results show that relative humidity over the Mediterranean remained relatively constant around 70%, apparently narrowly constrained to the lower end of the range observed globally over sea surfaces by the basin's land-locked character. Isotopic depletion in run off, relative to the present, is identified as the main potential cause of depletions in the Mediterranean d18O record. Also, slight increases in relative humidity (of the order of 5%) might have caused very pronounced isotopic depletions, such as that in sapropel S5 of the penultimate interglacial maximum. The model shows distinctly non proportional responses of d18O and salinity to environmental change, which argues against the use of isotope residuals in Mediterranean paleosalinity reconstructions.

(Table 1) Relarive abundance of foraminiferal species in the surface layer of bottom sediments from the Atlantic Ocean

Quantitative ratios of tests of planktonic foraminiferal species in thanatocoenoses within the surface layer of bottom sediments from Iceland to the Equator are described. Subarctic, boreal, subtropical and tropical types of thanatocoenoses and their subtypes are distinguished. Each subtype corresponds to a 2-3°C interval of mean annual temperature of the upper layer of ocean water. Comparison of fossil thanatocoenoses from Quaternary sediment cores with recent thanatocoenoses offers new potentials for paleotemperature analysis.

Biogenic components, major, trace and rare earth elements of equatorial Pacific Ocean surface sediments (Table 1)

We have analyzed the major, trace, and rare earth element composition of surface sediments collected from a transect across the Equator at 135°W longitude in the Pacific Ocean. Comparing the behavior of this suite of elements to the CaCO3, opal, and Corg fluxes (which record sharp maxima at the Equator, previously documented at the same sampling stations) enables us to assess the relative significance of the various pathways by which trace elements are transported to the equatorial Pacific seafloor. The 1. (1) high biogenic source at the Equator, associated with equatorial divergence of surface water and upwelling of nutrient-rich water, and 2. (2) high aluminosilicate flux at 4°N, associated with increased terrigenous input from elevated rainfall at the Intertropical Convergence Zone (ITCZ) of the tradewinds, are the two most important fluxes with which elemental transport is affiliated. The biogenic flux at the Equator transports Ca and Sr structurally bound to carbonate tests and Mn primarily as an adsorbed component. Trace elements such as Cr, As, Pb, and the REEs are also influenced by the biogenic flux at the Equator, although this affiliation is not regionally dominant. Normative calculations suggest that extremely large fluxes of Ba and P at the Equator are carried by only small proportions of barite and apatite phases. The high terrigenous flux at the ITCZ has a profound effect on chemical transport to the seafloor, with elemental fluxes increasing tremendously and in parallel with Ti. Normative calculations, however, indicate that these fluxes are far in excess of what can be supplied by lattice-bound terrigenous phases. The accumulation of Ba is greater than is affiliated with biogenic transport at the Equator, while the P flux at the ITCZ is only 10% less than at the Equator. This challenges the common view that Ba and P are essentially exclusively associated with biogenic fluxes. Many other elements (including Mn, Pb, As, and REEs) also record greater accumulation beneath the ITCZ than at the Equator. Thus, adsorptive scavenging by terrigenous paniculate matter, or phases intimately associated with them, appears to be an extremely important process regulating elemental transport to the equatorial Pacific seafloor. These findings emphasize the role of vertical transport to the sediment, and provide additional constraints on the paleochemical use of trace elements to track biogenic and terrigenous fluxes.

(Table 1) Radiocarbon ages of Bivalvia shells obtained from core ASV13_1157, Novaya Zemlya Trench

It is shown that sediments accumulated in the Southern Novaya Zemlya Trench at both deglaciation and marine stages. Permanent sea ice sheet existed during the deglaciation, and glacier meltwater was intensely delivered to the bottom layer. Along with the dominant sediment supply from the Southern Island of Novaya Zemlya, southern continental sources also played a noticeable role at that stage. Seasonal sea ice freezing led to the formation of cold brines at the marine stage. Like paleoproductivity, these processes were irregular. Dissolution of calcareous benthic foraminiferal tests considerably intensified after about 7 ka BP owing to a stronger Atlantic water advection into the Western Arctic and consequent increase in paleoproductivity, whereas the relative role of southern sedimentary provenances decreased. Sedimentation rates were constant (45 cm/ka) during the entire marine stage.

(Table 2) Terrigenous, authigenic and biogenic composition of sediments at DSDP Hole 93-603B

Pelagic sedimentation during the Early Cretaceous at Site 603 produced alternations of laminated marly limestone and bioturbated limestone-a facies typical of the "Blake-Bahama Formation" of the western Atlantic. This limestone is a nannofossil micrite, rich in calcified radiolarians, with variable amounts of organic matter, pyritized radiolarian tests, fish debris, and micaceous silt. The laminated marly limestone layers are enriched in organic matter when compared with the intervals of bioturbated limestone. The organic carbon is predominantly terrestrial plant debris; where the organic-carbon content is in excess of 1%, there is also a significant marine-derived component. Laminations can result either from bands of alternately enriched and depleted opaque material and clay, or from bands of elongate lenses (microflasers) of micrite, which could be plastically deformed pellets or diagenetic features. The alternating intervals of laminated and bioturbated structures may have resulted from combined changes in surface productivity, in the influx of terrigenous organic matter, and in the intensity of bottom circulation, which led to episodic oxygen depletion in the bottom water and sediments. Variations in the relative proportions of laminated clay-rich and bioturbated lime-rich limestone and in the development of cycles between these structures make it possible to subdivide the Lower Cretaceous pelagic facies into several subunits which appear to be regional in extent. Bioturbated limestone is dominant in the Berriasian, laminated marly limestone in the Valanginian and Barremian-lower Aptian, and well-developed alternations between these end members in the Hauterivian. The Hauterivian to lower Aptian sediments contain abundant terrigenous clastic turbidites associated with a submarine fan complex. These changes in the general characteristics of the pelagic sediment component of the Blake-Bahama Formation at Site 603 are synchronous with those in the Blake-Bahama Basin (Sites 534 and 391) to the south. Carbonate sedimentation ended in the early Aptian, probably because of a regional shoaling of the carbonate compensation depth.

(Table 1) Temperature and foraminiferal Mg/Ca ratios of samples off Japan

We studied Mg/Ca in high-Mg, shallow-water benthic foraminifera in culture and in samples from natural environments, in order to evaluate the expression of latitudinal and seasonal temperature variability in Mg/Ca in their tests. We cultured Planoglabratella opercularis (d'Orbigny) and Quinqueloculina yabei Asano under controlled temperature (10°-25°C) and salinity (30-38) conditions. Both species show a linear correlation between Mg/Ca and temperature, but they differ in temperature sensitivity. Salinity does not significantly influence Mg/Ca. In the samples collected in nature, Mg/Ca and seawater temperatures are positively correlated, but there are more complexities than in the records for cultured specimens due to such factors as seasonal fluctuations in temperature. We conclude that Mg/Ca ratios in monospecific benthic foraminiferal samples may be used as a reliable temperature proxy, if the lifetime of the species is taken into account.