Aseptic Processing of Meat Products

Aseptic processing involves sterilising the product (most meat products being low-acid foods containing particulates) and package separately, and filling under sterile conditions. Advantages include better product quality compared with canned products, lower transport and storage costs compared with frozen products, and virtually no restriction on package size. Problems include ensuring adequate heat penetration into the particles to ensure sterility, preventing separation of particles from the carrier liquid, and retention of particle structure and shape. Particulate foods can be sterilised in scraped-surface heat exchangers. Other methods involve heating the particles separately, and combining them during filling. The effects of aseptic processing on meat product quality (colour, flavour, texture, and mutrition) are outlined in this paper.

Field assessment of the resistance of timber products to termite (Isoptera) damage: Results can change with the amount of bait wood

Whether or not termites initiate damage to timber via the end grain may determine the need for spot-treating the exposed untreated cut ends of envelope-treated softwood framing material. Australian Coptotermes acinaciformis (Froggatt) were field-tested for their ability to initiate feeding via the end grain of timber (35 × 90 mm) treated with a repellent Tanalith® T envelope. Specimens of commercial radiata pine Pinus radiata D.Don framing timber (untreated) and slash pine Pinus elliottii Englem. (untreated and envelope-treated) were partially clad in fine stainless steel mesh. Clad and unclad specimens were exposed to C. acinaciformis near Townsville, North Queensland, Australia, for four months. Results showed that this species of termite can indeed damage timber via the end grain, including exposed untreated cut ends of envelope-treated material as demonstrated earlier for different populations of C. acinaciformis. Differences between the test conditions in field trials carried out at different times (where C. acinaciformis either did or did not damage timber via the end grain) are discussed. Clearly, outcomes from field studies with preservative-treated materials are dependent upon experimental conditions. Notably, the amount of bait wood (highly termite-susceptible timber substrate) offered in a given method can strongly influence the termite response. Further investigation is required to standardise this aspect of conditions in protocols for the assessment of wood preservatives.

Microbial susceptibility of condensation products of carboxy-terminated polybutadiene and glycerol

Keeping in view the prospects of biodegradable polymers, a polymer was synthesized by the condensation of carboxy-terminated polybutadiene (CTPB) of Mnsim-5000 with glycerol and tested for its microbial susceptibility. The results of end group estimations and viscosity measurements indicated a quantitative reaction between the two reactants under experimental conditions. The clear-zone method was employed in this investigation to test biodegradability. Two strains of Serratia and three strains of Staphylococcus did show a clear zone surrounding the colony. However, the microbial growth was found to diminish after 4 or 5 days.

Building better information products by assessing the information needs of growers of subtropical strawberries in Queensland

Timely access to effective technical information is a key ingredient of profitable strawberry production. Through the Better Berries Program, a joint RD&E initiative of government and industry, a number of information products and services have been provided in recent years to Australia's subtropical strawberry industry, centred in southern Queensland. However, there is a lack of knowledge of how well these are meeting the information needs of growers, both in content and delivery. To better understand grower information use and needs, a stratified sample of 25 growers was interviewed on-farm during the 2004 season. Growers were asked about how they currently accessed information, what they thought of a range of information products and ideas on show, and what advice they would provide for information development in the future. Results indicated that information sought by growers and the style in which it is best presented, varied considerably with grower experience, but little with farm size. New growers had a wide range of needs while the needs of experienced growers were focused mainly on problem identification and new production development. Interestingly, the overwhelming majority across all sectors still preferred paper-based information products despite their extensive use of computers for business purposes. The findings were used to develop a strategy for an improved range of technical information products and services that are more accessible, easier to use, more timely, and more relevant to the needs of growers.

A reply to a discussion by D.J. Cook of the paper a reaction product of lime and silica from rice husk asha star, open

Abstract is not available.

Cannibalism contributes significantly to the diet of cultured sand crabs, Portunus pelagicus (L.): A dual stable isotope study

The significance of cannibalism in the diet of juvenile pond-cultured blue swimmer crabs (Portunus pelagicus (L.)) was investigated using dual stable isotope analysis of carbon and nitrogen. In a laboratory feeding experiment, δ15N demonstrated a constant trophic shift (Δδ15N ≈+ 1.6‰), and therefore seemed to be a reliable indicator for assessing trophic position for P. pelagicus. This agrees with previously reported trends. Difference in growth rate did not seem to influence δ15N values. In contrast, δ13C did not display consistent shifts between trophic levels (range of Δδ13C: + 1 to + 1.7‰). The results from the pond experiment showed that larger individuals had a more enriched δ15N than smaller individuals, which, when compared to the results from the laboratory experiment, indicates that larger individuals were at a higher trophic level. This is most likely due to cannibalism prevailing in the pond rather than a direct result of faster growth rate. Cannibalistic behaviour might further increase growth, resulting in the observed positive correlation between size and δ15N.

Effects of hooking damage and hook type on post-release survival of sand flathead (Platycephalus bassensis)

This study examined post-release survival in sand flathead (Platycephalus bassensis) and whether there were survival benefits from the use of circle hooks over conventional hook patterns. Anatomical hooking location was the major factor contributing to mortality, with an almost 100% survival rate for fish hooked in the lip, mouth or eye (shallow-hooked) compared with around 64% for fish hooked in the throat or gut (deep-hooked). Mortality in deep-hooked fish was generally associated with injuries to vital organs (gills, heart, liver) and survival was significantly lower if bleeding was associated with injury (54% compared with 85% for non-bleeders). Circle hooks resulted in significantly lower deep-hooking rates (1%) compared with conventional hook types (4-9%) and, based on catch rates, were at least as effective as conventional hook patterns. Estimated survival rates for line-caught sand flathead were high, over 99% for circle hooks and between 94 and 97% for conventional hooks. These findings support the efficacy of management strategies based on size and bag limits and the practice of catch-and-release fishing for sand flathead, as well as a potential conservation benefit from the use of circle hooks.

Bearing capacity of square footings on geosynthetic reinforced sand

The results from laboratory model tests and numerical simulations on square footings resting on sand are presented. Bearing capacity of footings on geosynthetic reinforced sand is evaluated and the effect of various reinforcement parameters like the type and tensile strength of geosynthetic material, amount of reinforcement, layout and configuration of geosynthetic layers below the footing on the bearing capacity improvement of the footings is studied through systemati model studies. A steel tank of size 900 x 900 x 600 mm is used for conducting model tests. Four types of grids, namely strong biaxial geogrid, weak biaxial geogrid, uniaxial geogrid and a geonet, each with different tensile strength, are used in the tests. Geosynthetic reinforcement is provided in the form of planar layers, varying the depth of reinforced zone below the footing, number of geosynthetic layers within the reinforced zone and the width of geosynthetic layers in different tests. Influence of all these parameters on the bearing capacity improvement of square footing and its settlement is studied by comparing with the test on unreinforced sand. Results show that the effective depth of reinforcement is twice the width of the footing and optimum spacing of geosynthetic layers is half the width of the footing. It is observed that the layout and configuration of reinforcement play a vital role in bearing capacity improvement rather than the tensile strength of the geosynthetic material. Experimental observations are supported by the findings from numerical analyses.

Vertical uplift capacity of two interfering horizontal anchors in sand using an upper bound limit analysis

The vertical uplift resistance of two interfering rigid rough strip anchors embedded horizontally in sand at shallow depths has been examined. The analysis is performed by using an upper bound theorem o limit analysis in combination with finite elements and linear programming. It is specified that both the anchors are loaded to failure simultaneously at the same magnitude of the failure load. For different clear spacing (S) between the anchors, the magnitude of the efficiency factor (xi(gamma)) is determined. On account of interference, the magnitude of xi(gamma) is found to reduce continuously with a decrease in the spacing between the anchors. The results from the numerical analysis were found to compare reasonably well with the available theoretical data from the literature.

Development and testing of an evaluation procedure for commercial manure additive products.

Manure additive products can be used to reduce odour emissions (OE) from livestock farms. The standardised evaluation of these manure additive products under specific farm conditions is important. In this study, the efficacy of a manure additive (WonderTreat(TM), CKLS, Inc., Hong-Kong) was assessed under Australian conditions utilising a combination of laboratory and field-scale evaluation techniques. As a first step, the efficacy of the manure additive was assessed in a laboratory-scale trial using a series of uniformly managed digesters and standard odour, liquor ammonia and hydrogen sulphide concentration measurement procedures. This showed that the addition of WonderTreat(TM) at the 'low dose rate' (LDR) (102.6 g m-2) used during the trial significantly, but only marginally (30%; P = 0.02) reduced the OE rate (mean 13.9 OU m-2 s-1) of anaerobic pig liquor relative to an untreated control (UC) (19.9 OU m-2 s-1). However, the 'high dose rate' (HDR) (205.3 g m-2) also assessed during the trial preformed similarly (19.7 OU m-2 s-1) to the UC. No statistically significant difference in the concentrations of a range of measured water quality variables at the 5% level was observed between the treatments or controls digesters. As a second step, a field-scale assessment of the manure additive was undertaken at a commercial piggery. Two piggery manure lagoons (each with approximately 2500 m2 surface area) were included in the study; one was treated with WonderTreat(TM) while the other was used as control. The efficacy of the treatment was assessed using olfactometric evaluation of odour samples collected from the surface of the pond using a dynamic wind tunnel and ancillary equipment. No statistically significant reduction in OE rate could be demonstrated (P = 0.35), partially due to the limited number of samples taken during the assessment. However, there was a numerical reduction in the average OE rate of the treatment pond (29 OU m-2 s-1 at 1 m s-1) compared to the control lagoon (38 OU m-2 s-1 at 1 m s-1).

Food-borne pathogens and pig waste products - the spoke in the wheel?

Food-borne pathogens are present in normal healthy pigs and thus are also present in pig wastes and by-products. The presence of these pathogens can be viewed negatively (i.e. 'a spoke in the wheel') or as simply another issue that requires the adoption of appropriate guidelines and management procedures. A key component in the development of appropriate, effective guidelines and management practices is a solid basis of knowledge on which pathogens are present as well as the levels of these pathogens. This paper reviews Australian Pork Limited (APL) funded projects carried out in our laboratories that have provided a solid base of Australian data for the pig industry. These data will ensure that pathogens are not 'a spoke in the wheel' but rather an issue - like many others that confront the industry - that can be managed to ensure that there is no unacceptable risk to either public health or the environment.

Prevalence, persistence and control of Salmonella and Listeria in shrimp and shrimp products: A review.

Shrimp are an important commodity in the international fisheries trade and there is an indication of an increase in worldwide consumption of this crustacean. Salmonella and Listeria have been isolated from shrimps and shrimp products on a regular basis since the 1980s. The continued reporting of the presence of these pathogens in fresh and frozen shrimps, and even in the lightly preserved and ready-to-eat products, indicates that the existing practices used by the manufacturers or processors are insufficient to eliminate these pathogens. This paper reviews the information available on Salmonella and Listeria in shrimp and makes recommendations on control options and avenues for future research in order to improve shrimp safety and quality.

Stream power criterion and design of sand bed channels at incipient motion

The critical stream power criterion may be used to describe the incipient motion of cohesionless particles of plane sediment beds. The governing equation relating ``critical stream power'' to ``shear Reynolds number'' is developed by using the present experimental data as well as the data from several other sources. Simultaneously, a resistance equation, relating the ``particle Reynolds number'' to the``shear Reynolds number'' is developed for plane sediment beds in wide channels with little or no transport. By making use of these relations, a procedure is developed to design plane sediment beds such that any two of the four design variables, including particle size, energy/friction slope, flow depth, and discharge per unit width in the channel should be known to predict the remaining two variables. Finally, a straightforward design procedure using design tables/design curves and analytical methods is presented to solve six possible design problems.

Queensland Coastal Wetland Resources: Sand Bay to Keppel Bay.

Protection of coastal wetland environments is an important prerequisite to effective and sustainable inshore fisheries management and conservation of habitats for use by future generations. Mangroves, saltmarshes, seagrasses and non vegetated habitats directly support local and regional inshore and offshore fisheries through the provision of food, shelter, breeding and nursery grounds. As such, these wetland environments have significant economic value as well as their intrinsic aesthetic and ecological values. This report summarises the results of the mapping undertaken in the Central Queensland Coast from Sand Bay to Keppel Bay (hereafter referred to as the Study Area). The study was undertaken in order to: 1. document and map the coastal wetland communities along the Queensland coastline from Sand Bay (20.93°S, 149.04°E) to Keppel Bay (23.65°S, 151.07°E); 2. document levels of existing disturbance to and protection of the wetlands; 3. examine existing recreational and commercial fisheries in the region; and 4. evaluate the conservation values of the areas investigated from the viewpoint of fisheries productivity and as habitat for important and/or threatened species. Dataset URL Link: Queensland Coastal Wetlands Resources Mapping data. [Dataset]

Radish sprouts versus broccoli sprouts: a comparison of anti-cancer potential based on glucosinolate breakdown products.

Radish sprouts and broccoli sprouts have been implicated in having a potential chemoprotective effect against certain types of cancer. Each contains a glucosinolate that can be broken down to an isothiocyanate capable of inducing chemoprotective factors known as phase 2 enzymes. In the case of broccoli, the glucosinolate, glucoraphanin, is converted to an isothiocyanate, sulforaphane, while in radish a similar glucosinolate, glucoraphenin, is broken down to form the isothiocyanate, sulforaphene. When sprouts are consumed fresh (uncooked), however, the principal degradation product of broccoli is not the isothiocyanate sulforaphane, but a nitrile, a compound with little anti-cancer potential. By contrast, radish sprouts produce largely the anti-cancer isothiocyanate, sulforaphene. The reason for this difference is likely to be due to the presence in broccoli (and absence in radish) of the enzyme cofactor, epithiospecifier protein (ESP). In vitro induction of the phase 2 enzyme, quinone reductase (QR), was significantly greater for radish sprouts than broccoli sprouts when extracts were self-hydrolysed. By contrast, boiled radish sprout extracts (deactivating ESP) to which myrosinase was subsequently added, induced similar QR activity to broccoli sprouts. The implication is that radish sprouts have potentially greater chemoprotective action against carcinogens than broccoli sprouts when hydrolysed under conditions similar to that during human consumption.