Laser assisted directional solidification of zirconia-based eutectics

Directionally solidified zirconia-based eutectic (DSE) fibres were obtained using the laser floating zone (LFZ) method. Two systems were investigated: zirconia-barium zirconate and zirconia-mullite. The purpose was to take advantage of zirconia properties, particularly as an ionic conductor and a mechanical rein-forcement phase. The influence of processing conditions in the structural and microstructural characteristics and their consequences on the electrical and mechanical behaviour were the focus of this thesis. The novel zirconia-barium zirconate eutectic materials were developed in order to combine oxygen ionic conduction through zirconia with protonic conduction from barium zirconate, promoting mixed ionic conduction behaviour. The mi-crostructure of the fibres comprises two alternated regions: bands having coarser zirconia-rich microstructure; and inter-band regions changing from a homogeneous coupled eutectic, at the lowest pulling rate, to columnar colony microstructure, for the faster grown fibres. The bands inter-distance increases with the growth rate and, at 300 mm/h, zirconia dendrites develop enclosed in a fine-interpenetrated network of 50 vol.% ZrO2-50 vol.% BaZrO3. Both phases display contiguity without interphase boundaries, according to impedance spec-troscopy data. Yttria-rich compositions were considered in order to promote the yttrium incorporation in both phases, as revealed by Raman spectroscopy and corroborated by the elemental chemical analysis in energy dispersive spectros-copy. This is a mandatory condition to attain simultaneous contribution to the mixed ionic conduction. Such results are supported by impedance spectrosco-py measurements, which clearly disclose an increase of total ionic conduction for lower temperatures in wet/reduction atmospheres (activation energies of 35 kJ/mol in N2+H2 and 48 kJ/mol in air, in the range of 320-500 ºC) compared to the dry/oxidizing conditions (attaining values close to 90 kJ/mol, above 500 ºC). At high temperatures, the proton incorporation into the barium zirconate is un-favourable, so oxygen ion conduction through zirconia prevails, in dry and oxi-dizing environments, reaching a maximum of 1.3x10-2 S/cm in dry air, at ~1000 ºC. The ionic conduction of zirconia was alternatively combined with another high temperature oxygen ion conductor, as mullite, in order to obtain a broad elec-trolytic domain. The growth rate has a huge influence in the amount of phases and microstructure of the directionally solidified zirconia-mullite fibres. Their microstructure changes from planar coupled eutectic to dendritic eutectic mor-phology, when the growth rate rises from 1 to 500 mm/h, along with an incre-ment of tetragonal zirconia content. Furthermore, high growth rates lead to the development of Al-Si-Y glassy phase, and thus less mullite amount, which is found to considerably reduce the total ionic conduction of as-grown fibres. The reduction of the glassy phase content after annealing (10h; 1400 ºC) promotes an increase of the total ionic conduction (≥0.01 S/cm at 1370 °C), raising the mullite and tetragonal zirconia contents and leading to microstructural differ-ences, namely the distribution and size of the zirconia constituent. This has important consequences in conductivity by improving the percolation pathways. A notable increase in hardness is observed from 11.3 GPa for the 10 mm/h pulled fibre to 21.2 GPa for the fibre grown at 500 mm/h. The ultra-fine eutectic morphology of the 500 mm/h fibres results in a maximum value of 534 MPa for room temperature bending strength, which decreases to about one-fourth of this value at high temperature testing (1400 ºC) due to the soft nature of the glassy-matrix.

eHealth e a adoção da inovação em assisted living technologies : o caso das demências

RESUMO - Assistimos hoje a um contexto marcado (i) pelo progressivo envelhecimento das sociedades ocidentais, (ii) pelo aumento da prevalência das doenças crónicas, de que as demências são um exemplo, (iii) pelo significativo aumento dos custos associados a estas patologias, (iv) por orçamentos públicos fortemente pressionadas pelo controlo da despesa, (v) por uma vida moderna que dificulta o apoio intergeracional, tornando o suporte proporcionado pelos filhos particularmente difícil, (vi) por fortes expectativas relativamente à prestação de cuidados de saúde com qualidade. Teremos assim de ser capazes de conseguir melhorar os serviços de saúde, ao mesmo tempo que recorremos a menos recursos financeiros e humanos, pelo que a inovação parece ser crítica para a sustentabilidade do sistema. Contudo a difusão das Assistive Living Technologies, apesar do seu potencial, tem sido bastante baixa, nomeadamente em Portugal. Porquê? Hamer, Plochg e Moreira (2012), no editorial do International Journal of Healthcare Management, enquadram a Inovação como “podendo ser imprevisível e mesmo dolorosa, pelo que talvez possamos não ficar surpreendidos se surgirem resistências e que, inovações bastante necessárias, capazes de melhorar os indicadores de saúde, tenham sido de adoção lenta ou que tenham mesmo sido insustentáveis”. Em Portugal não há bibliografia que procure caracterizar o modelo de difusão da inovação em eHealth ou das tecnologias de vivência assistida. A bibliografia internacional é igualmente escassa. O presente projeto de investigação, de natureza exploratória, tem como objetivo principal, identificar barreiras e oportunidades para a implementação de tecnologias eHealth, aplicadas ao campo das demências. Como objetivos secundários pretendemse identificar as oportunidades e limitações em Portugal: mapa de competências nacionais, e propor medidas que possa acelerar a inovação em ALT, no contexto nacional. O projeto seguirá o modelo de um estudo qualitativo. Para o efeito foram conduzidas entrevistas em profundidade junto de experts em ALT, procurando obter a visão daqueles que participam do lado da Oferta- a Indústria; do lado da Procura- doentes, cuidadores e profissionais de saúde; bem como dos Reguladores. O instrumento utilizado para a recolha da informação pretendida foi o questionário não estruturado. A análise e interpretação da informação recolhida foram feitas através da técnica de Análise de Conteúdo. Os resultados da Análise de Conteúdo efetuada permitiram expressar a dicotomia barreira/oportunidade, nas seguintes categorias aqui descritas como contextos (i) Contexto Tecnológico, nas subcategorias de Acesso às Infraestruturas; Custo da Tecnologia; Interoperabilidade, (ii) Contexto do Valor Percecionado, nas subcategorias de Utilidade; Eficiência; Divulgação, (iii) Contexto Político, compreendendo a Liderança; Organização; Regulação; Recursos, (iv) Contexto Sociocultural, incluindo nomeadamente Idade; Literacia; Capacidade Económica, (v) Contexto Individual, incluindo como subcategorias, Capacidade de Adaptação a Novas tecnologias; Motivação; Acesso a equipamentos (vi) Contexto Específico da Doença, nomeadamente o Impacto Cognitivo; Tipologia Heterogénea e a Importância do Cuidador. Foi proposto um modelo exploratório, designado de Modelo de Contextos e Forças, que estudos subsequentes poderão validar. Neste modelo o Contexto Tecnológico é um Força Básica ou Fundamental; o Contexto do Valor Percecionado, constitui-se numa Força Crítica para a adoção de inovação, que assenta na sua capacidade para oferecer valor aos diversos stakeholders da cadeia de cuidados. Temos também o Contexto Político, com capacidade de modelar a adoção da inovação e nomeadamente com capacidade para o acelerar, se dele emitir um sinal de urgência para a mudança. O Contexto Sociocultural e Individual expressam uma Força Intrínseca, dado que elas são características internas, próprias e imutáveis no curto-prazo, das sociedade e das pessoas. Por fim há que considerar o Contexto Específico da Doença, nesta caso o das demências. Das conclusões do estudo parece evidente que as condições tecnológicas estão medianamente satisfeitas em Portugal, com evidentes progressos nos últimos anos (exceção para a interoperabilidade aonde há necessidade de maiores progressos), não constituindo portanto barreira à introdução de ALT. Aonde há necessidade de investir é nas áreas do valor percebido. Da análise feita, esta é uma área que constitui uma barreira à introdução e adoção das ALT em Portugal. A falta de perceção do valor que estas tecnologias trazem, por parte dos profissionais de saúde, doentes, cuidadores e decisores políticos, parece ser o principal entrave à sua adoção. São recomendadas estratégias de modelos colaborativos de Investigação e Desenvolvimento e de abordagens de cocriação com a contribuição de todos os intervenientes na cadeia de cuidados. Há também um papel que cabe ao estado no âmbito das prioridades e da mobilização de recursos, sendo-lhe requerida a expressão do sentido de urgência para que esta mudança aconteça. Foram também identificadas oportunidades em diversas áreas, como na prevenção, no diagnóstico, na compliance medicamentosa, na terapêutica, na monitorização, no apoio à vida diária e na integração social. O que é necessário é que as soluções encontradas constituam respostas àquilo que são as verdadeiras necessidades dos intervenientes e não uma imposição tecnológica que só por si nada resolve. Do estudo resultou também a perceção de que há que (i) continuar a trabalhar no sentido de aproximar a comunidade científica, da clínica e do doente, (ii) fomentar a colaboração entre centros, com vista à criação de escala a nível global. Essa colaboração já parece acontecer a nível empresarial, tendo sido identificadas empresas Portuguesas com vocação global. A qualidade individual das instituições de ensino, dos centros de investigação, das empresas, permite criar as condições para que Portugal possa ser país um piloto e um case-study internacional em ALT, desde que para tal pudéssemos contar com um trabalho colaborativo entre instituições e com decisões políticas arrojadas.

Vascular dysfunction in children conceived by assisted reproductive technologies: underlying mechanisms and future implications.

Epidemiological studies in humans have demonstrated a relationship between pathological events during fetal development and increased cardiovascular risk later in life and have led to the so called "Fetal programming of cardiovascular disease hypothesis". The recent observation of generalised vascular dysfunction in young apparently healthy children conceived by assisted reproductive technologies (ART) provides a novel and potentially very important example of this hypothesis. This review summarises recent data in ART children demonstrating premature subclinical atherosclerosis in the systemic circulation and pulmonary vascular dysfunction predisposing to exaggerated hypoxia-induced pulmonary hypertension. These problems appear to be related to the ART procedure per se. Studies in ART mice demonstrating premature vascular aging and arterial hypertension further demonstrate the potential of ART to increase cardiovascular risk and have allowed to unravel epigenetic alterations of the eNOS gene as an underpinning mechanism. The roughly 25% shortening of the life span in ART mice challenged with a western style high-fat-diet demonstrates the potential importance of these alterations for the long-term outcome. Given the young age of the ART population, data on cardiovascular endpoints will not be available before 20 to 30 years from now. However, already now cohort studies of the ART population are needed to early detect cardiovascular alterations with the aim to prevent or at least optimally treat cardiovascular complications. Finally, a debate needs to be engaged on the future of ART and the consequences of its exponential growth for public health.

Carbon Nanotube Growth Using Ni Catalyst in Different Layouts

Vertically aligned carbon nanotubes have been grown using Ni as catalyst by plasma enhanced chemical vapor deposition system (PECVD) in various pre-patterned substrates. Ni was thermally evaporated on silicon substrates with anodized alumina mask prepared in different methods including 2 step anodization of porous alumina template and interference lithography assisted array of pores. The templates helped to define Ni nanodots inside the pores which in turn catalyzed the growth of carbon nanotubes inside the PECVD system at temperature of 700-750C using mixture of ammonia and acetylene gases. The resulting well-aligned multi-walled carbon nanotubes were further investigated using SEM, TEM and Raman spectroscopy. The size, shape and structure of the grown carbon nanotubes were also discussed.

PCR-based markers diagnostic for spring and winter seasonal growth habit in barley

Toward the ultimate goal of replacing field-based evaluation of seasonal growth habit, we describe the design and validation of a multiplex polymerase chain reaction assay diagnostic for allelic status at the barley (Hordeum vulgare ssp. vulgare L.) vernalization locus, VRN-H1 By assaying for the presence of all known insertion–deletion polymorphisms thought to be responsible for the difference between spring and winter alleles, this assay directly tests for the presence of functional polymorphism at VRN-H1 Four of the nine previously recognized VRN-H1 haplotypes (including both winter alleles) give unique profiles using this assay. The remaining five spring haplotypes share a single profile, indicative of function-altering deletions spanning, or adjacent to, the putative “vernalization critical” region of intron 1. When used in conjunction with a previously published PCR-based assay diagnostic for alleles at VRN-H2, it was possible to predict growth habit in all the 100 contemporary UK spring and winter lines analyzed in this study. This assay is likely to find application in instances when seasonal growth habit needs to be determined without the time and cost of phenotypic assessment and during marker-assisted selection using conventional and multicross population analysis.

Effects of parylene-C photooxidation on serum-assisted glial and neuronal patterning

The increasing use of patterned neural networks in multielectrode arrays and similar devices drives the constant development and evaluation of new biomaterials. Recently, we presented a promising technique to guide neurons and glia reliably and effectively. Parylene-C, a common hydrophobic polymer, was photolithographically patterned on silicon oxide (SiO2) and subsequently activated via immersion in serum. In this article, we explore the effects of ultraviolet (UV)-induced oxidation on parylene's ability to pattern neurons and glia. We exposed parylene-C stripe patterns to increasing levels of UV radiation and found a dose-dependent reduction in the total mass of patterned cells, as well as a gradual loss of glial and neuronal conformity to the patterns. In contrast, nonirradiated patterns had superior patterning results and increased presence of cells. The reduced cell adhesion and patterning after the formation of aldehyde and carboxyl groups on UV-radiated parylene-C supports our hypothesis that cell adhesion and growth on parylene is facilitated by hydrophobic adsorption of serum proteins. We conclude that unlike other cell patterning schemes, our technique does not rely on photooxidation of the polymer. Nonetheless, the precise control of oxygenated groups on parylene could pave the way for the differential binding of proteins and other molecules on the surface, aiding in the adhesion of alternative cell types. © 2010 Wiley Periodicals, Inc. J Biomed Mater Res, 2010

Assessment of DGAT1 and LEP gene polymorphisms in three Nelore (Bos indicus) lines selected for growth and their relationship with growth and carcass traits

The aim of this study was to analyze LEP and DGAT1 gene polymorphisms in 3 Nelore lines selected for growth and to evaluate their effects on growth and carcass traits. Traits analyzed were birth, weaning, and yearling weight, rump height, LM area, backfat thickness, and rump fat thickness obtained by ultrasound. Two SNP in the LEP gene [LEP 1620(A/G) and LEP 305(T/C)] and the K232A mutation in the DGAT1 gene were analyzed. The sample consisted of 357 Nelore heifers from 2 lines selected for yearling weight and a control line, established in 1980, at the Estacao Experimental de Zootecnia de Sertaozinho (Sertaozinho, Brazil). Three genotypes were obtained for each marker. Differences in allele frequencies among the 3 lines were only observed for the DGAT1 K232A polymorphism, with the frequency of the A allele being greater in the control line than in the selected lines. The DGAT1 K232A mutation was associated only with rump height, whereas LEP 1620(A/G) was associated with weaning weight and LEP 305(T/C) with birth weight and backfat thickness. However, more studies, with larger data sets, are necessary before these makers can be used for marker-assisted selection.

Effect of Different Solvent Ratios (Water/Ethylene Glycol) on the Growth Process of CaMoO(4) Crystals and Their Optical Properties

In this paper, calcium molybdate (CaMoO(4)) crystals (meso- and nanoscale) were synthesized by the coprecipitation method using different solvent volume ratios (water/ethylene glycol). Subsequently, the obtained suspensions were processed in microwave-assisted hydrothermal/solvothermal systems at 140 degrees C for 1 h. These meso- and nanocrystals processed were characterized by X-ray diffraction (X R I)), Fourier transform Raman (FT-Raman), Fourier transform infrared (FT-IR). ultraviolet visible (UV-vis) absorption spectroscopies, held-emission gun scanning electron microscopy (FEG-SEM). transmission electron microscopy (TEM). and photoluminescence (PL) measurements. X RI) patterns and FT-Raman spectra showed that these meso- and nanocrystals have a scheelite-type tetragonal structure without the presence of deleterious phases. FT-IR spectra exhibited a large absorption band situated at around 827 cm(-1), which is associated with the Mo-O anti-symmetric stretching vibrations into the [MoO(4)] clusters. FEG-SEM micrographs indicated that the ethylene glycol concentration in the aqueous solution plays an important role in the morphological evolution of CaMoO(4) crystals. High-resolution TEM micrographs demonstrated that the mesocrystals consist of several aggregated nanoparticles with electron diffraction patterns of monocrystal. In addition, the differences observed in the selected area electron diffraction patterns of CaMoO(4) crystals proved the coexistence of both nano- and mesostructures, First-principles quantum mechanical calculations based on the density functional theory at the B3LYP level were employed in order to understand the band structure find density of states For the CaMoO(4). UV-vis absorption measurements evidenced a variation in optical band gap values (from 3.42 to 3.72 cV) for the distinct morphologies. The blue and green PI. emissions observed in these crystals were ascribed to the intermediary energy levels arising from the distortions on the [MoO(4)] clusters clue to intrinsic defects in the lattice of anisotropic/isotropic crystals.

Keratinocyte growth factor: a new mesothelial targeted therapy to reduce postoperative pericardial adhesions

Background: Several methods have been utilized to prevent pericardial and retrosternal adhesions, but none of them evaluated the mesothelial regenerative hypothesis. There are evidences that the mesothelial trauma reduces pericardial fibrinolytic capability and induces an adhesion process. Keratinocyte growth factor (KGF) has proven to improve mesothelial cells proliferation. This study investigated the influence of keratinocyte growth factor in reducing post-surgical adhesions. Methods: Twelve pigs were operated and an adhesion protocol was employed. Following a stratified randomization, the animals received a topical application of KGF or saline. At 8 weeks, intrapericardial adhesions were evaluated and a severity score was established. The time spent to dissect the adhesions and the amount of sharp dissection used, were recorded. Histological sections were stained with sirius red and morphometric analyses were assessed with a computer-assisted image analysis system. Results: The severity score was lower in the KGF group than in the control group (11.5 vs 17, p = 0.005). The dissection time was lower in the KGF group (9.2 +/- 1.4 min vs 33.9 +/- 9.2 min, p = 0.004) and presented a significant correlation with the severity score (r = 0.83, p = 0.001). A significantly less sharp dissection was also required in the KGF group. Also, adhesion area and adhesion collagen were significantly tower in the KGF group than in the control group. Conclusion: The simulation of pericardial cells with KGF reduced the intensity of postoperative adhesions and facilitated the re-operation. This study suggests that the mesothelial regeneration is the new horizon in anti-adhesion therapies. (C) 2008 European Association for Cardio-Thoracic Surgery. Published by Elsevier B.V. All rights reserved.

Synergism Between Keratinocyte Growth Factor and Carboxymethyl Chitosan Reduces Pericardial Adhesions

Background. Mesothelial injury is the pivot in the development of adhesions. An increase in the proliferation of mesothelial cells was verified by in vitro studies with the use of keratinocyte growth factor (KGF). This study investigated the influence of KGF associated with thermo-sterilized carboxymethyl chitosan (NOCCts) in the reduction of pericardial adhesions. Methods. An induction model of pericardial adhesion was carried out in 24 pigs. Animals were randomly allocated to receive topical application of KGF, KGF + NOCCts, NOCCts, or saline (control). At 8 weeks, intra-pericardial adhesions were evaluated and a severity score was established. The time spent to dissect the adhesions and the amount of sharp dissection used, were recorded. Histologic sections were stained with sirius red for a morphometric evaluation using a computer-assisted image analysis system. Cytokeratin AE1/AE3 immunostaining were employed to identify mesothelial cells. Results. The severity score expressed in median (minimum to maximum), in relation to the control group (17 [15 to 18]), was lower in the KGF + NOCCts group (7 [6 to 9], p < 0.01) followed by the KGF group (11.5 [9 to 12], 0.01 < p < 0.05) and the NOCCts group (12 [9 to 14], p > 0.05). The dissection time was significantly lower in the KGF + NOCCts group (7.1 +/- 0.6 vs 33.9 +/- 9.2 minutes, p < 0.001). A significantly less sharp dissection was also required in the KGF + NOCCts group. In the adhesion segment, a decreased collagen proportion was found in the KGF + NOCCts group (p < 0.05). Mesothelial cells were present more extensively in groups in which KGF was delivered (p = 0.01). Conclusions. The use of KGF associated with NOCCts resulted in a synergic action that decreases postoperative pericardial adhesions in a highly significant way. (Ann Thorac Surg 2010; 90: 566-72) (C) 2010 by The Society of Thoracic Surgeons

Tenocyte responses to mechanical loading in vivo : A role for local insulin-like growth factor 1 signaling in early tendinosis in rats

Objective
To investigate tenocyte regulatory events during the development of overuse supraspinatus tendinosis in rats.

Methods
Supraspinatus tendinosis was induced by running rats downhill at 1 km/hour for 1 hour a day. Tendons were harvested at 4, 8, 12, and 16 weeks and processed for brightfield, polarized light, or transmission electron microscopy. The development of tendinosis was assessed semiquantitatively using a modified Bonar histopathologic scale. Apoptosis and proliferation were examined using antibodies against fragmented DNA or proliferating cell nuclear antigen, respectively. Insulin-like growth factor 1 (IGF-1) expression was determined by computer-assisted quantification of immunohistochemical reaction. Local IGF-1 signaling was probed using antibodies to phosphorylated insulin receptor substrate 1 (IRS-1) and ERK-1/2.

Results
Tendinosis was present after 12 weeks of downhill running and was characterized by tenocyte rounding and proliferation as well as by glycosaminoglycan accumulation and collagen fragmentation. The proliferation index was elevated in CD90+ tenocytes in association with tendinosis and correlated with increased local IGF-1 expression by tenocytes and phosphorylation of IRS-1 and ERK-1/2. Both apoptosis and cellular inflammation were absent at all time points.

Conclusion
In this animal model, early tendinosis was associated with local stimulation of tenocytes rather than with extrinsic inflammation or apoptosis. Our data suggest a role for IGF-1 in the load-induced tenocyte responses during the pathogenesis of overuse tendon disorders.

Assisted Living: The Politics of Medicaid and Medicare

In this paper I examine the structure of the current assisted living industry in order to explain how and why it is appealing and effective, as well as look at its limitations. I discuss the politics of Medicaid and Medicare, and how through these programs the federal and state governments are failing to provide adequate care for the nation’s senior population. Like the rest of our health care system, these two public health insurance systems are fragmented, and consequently, financing long-term care is complicated and insufficient. Ultimately, this paper will function as a policy report and I will propose: standardized requirements for assisted living facilities; a stricter and new way to regulate assisted living on the state level; restructured models for the public insurance programs, including Medicaid, Medicare, and the State Children’s Health Insurance Program.

Flux-assisted self-assembly of monodisperse colloids

We have developed a novel method to grow ordered layers of monodisperse colloids on a flat substrate. The evaporation of the colloidal suspension in the presence of the inclined substrate is strengthened by an external gas flux directed on the meniscus. The meniscus oscillations caused by the gas flux have an evident effect on the ordering of the spheres on the substrate. Thick films (more than 150 layers in a single-step deposition) of large area single crystals (1 cm2) can be obtained in a very short time (~1 cm/h maximum growth rate) and from very diluted suspensions (up to 0.022% volume fraction).

Effect of a commercial alcohol ethoxylate surfactant (C11–15E7) on biodegradation of phenanthrene in a saline water medium by Neptunomonas naphthovorans

Biodegradation of poorly soluble polycyclic aromatic hydrocarbons (PAHs) has been a challenge in bioremediation. In recent years, surfactant-enhanced bioremediation of PAH contaminants has attracted great attention in research. In this study, biodegradation of phenanthrene as a model PAHs solubilized in saline micellar solutions of a biodegradable commercial alcohol ethoxylate nonionic surfactant was investigated. The critical micelle concentration (CMC) of the surfactant and its solubilization capacity for phenanthrene were examined in an artificial saline water medium, and a type of marine bacteria, Neptunomonas naphthovorans, was studied for the biodegradation of phenanthrene solubilized in the surfactant micellar solutions of the saline medium. It is found that the solubility of phenanthrene in the surfactant micellar solutions increased linearly with the surfactant concentrations, but, at a fixed phenanthrene concentration, the biodegradability of phenanthrene in the micellar solutions decreased with the increase of the surfactant concentrations. This was attributed to the reduced bioavailability of phenanthrene, due to its increased solubilization extent in the micellar phase and possibly lowered mass transfer rate from the micellar phase into the aqueous phase or into the bacterial cells. In addition, an inhibitory effect of the surfactant on the bacterial growth at high surfactant concentrations may also play a role. It is concluded that the surfactant largely enhanced the solubilization of phenanthrene in the saline water medium, but excess existence of the surfactant in the medium should be minimized or avoided for the biodegradation of phenanthrene by Neptunomonas naphthovorans.