Heterogeneous error-resilient scheme for spectral analysis in ultra-low power wearable electrocardiogram devices

Wearable devices performing advanced bio-signal analysis algorithms are aimed to foster a revolution in healthcare provision of chronic cardiac diseases. In this context, energy efficiency is of paramount importance, as long-term monitoring must be ensured while relying on a tiny power source. Operating at a scaled supply voltage, just above the threshold voltage, effectively helps in saving substantial energy, but it makes circuits, and especially memories, more prone to errors, threatening the correct execution of algorithms. The use of error detection and correction codes may help to protect the entire memory content, however it incurs in large area and energy overheads which may not be compatible with the tight energy budgets of wearable systems. To cope with this challenge, in this paper we propose to limit the overhead of traditional schemes by selectively detecting and correcting errors only in data highly impacting the end-to-end quality of service of ultra-low power wearable electrocardiogram (ECG) devices. This partition adopts the protection of either significant words or significant bits of each data element, according to the application characteristics (statistical properties of the data in the application buffers), and its impact in determining the output. The proposed heterogeneous error protection scheme in real ECG signals allows substantial energy savings (11% in wearable devices) compared to state-of-the-art approaches, like ECC, in which the whole memory is protected against errors. At the same time, it also results in negligible output quality degradation in the evaluated power spectrum analysis application of ECG signals.

Compression Efficiency Analysis of Wyner-Ziv Video Coding with Motion Compensated Side Information Interpolation

The Wyner-Ziv video coding (WZVC) rate distortion performance is highly dependent on the quality of the side information, an estimation of the original frame, created at the decoder. This paper, characterizes the WZVC efficiency when motion compensated frame interpolation (MCFI) techniques are used to generate the side information, a difficult problem in WZVC especially because the decoder only has available some reference decoded frames. The proposed WZVC compression efficiency rate model relates the power spectral of the estimation error to the accuracy of the MCFI motion field. Then, some interesting conclusions may be derived related to the impact of the motion field smoothness and the correlation to the true motion trajectories on the compression performance.

Mass spectral studies of some pentafluorophenyl derivatives of group V /|nby Andrew Tanner Rake. -- 260 St. Catharines, Ont. : [s. n.],

The mass spectra of compounds of t he series (C6F5 )3-n MP~ (n = 1,2,3, M = P and As ), (C6F5>3Sb, Ph) Sb and (C6F5 )2SbPh have been studied in detail and the important modes of fragmentation were e1ucidated, a ided by metastable ions. Various trends attributed to the central atom and or the . substituent groups have been noted and, where applicable, compared to recent studies on related phenyl and pentafluorophenyl compounds of groups IV and V. The mass spectra of fluorine containing organometallic compounds exhibit characteristic migrations of fluorine to t he central atom, giving an increasing abundance of MF+, MF2+' and RMF+ (R = Ph or C6F5) ions on descending the group_ The mass spectra of pentafluorophenyl , antimony, and arsenic compounds show a greater fragmentation of the aromatic ring than those of phosphorus. The mixed phenyl pentafluorophenyl derivatives show a characteristic pattern depending on the number of phenyl grm.lps present but show t he general characteristics of both the tris(phenyl) and tris(pentafluorophenyl) compounds. The diphenyl pentafluorophenyl der ivatives show the loss of biphenyl ion as the most import ant step, the los s of phenyl t o give the i on PhMC6F5 + being of secondary importance. The ,bis(pentafluorophenyl) phenyl derivatives fragment primarily by loss of PhC6F5 to give C6F5M+ ions, the abundance of t hese increasing r apidly from phosphorus to arsenic. This species then, exhibits a characteristic fragmentation observed in the tris(penta- fluorophenyl ) compounds. However, the abundance of (C6F5)2M+ species in these compounds i s small. I ons of the type C6H4MC6F4 + and tetrafluorobiphenylene ions C6H4C6F4 + also are observed on substitution of a phenyl group for a penta- fluorophenyl group. The fully fluorinated species (C6F4)2M+ is not observed, although octafluorobiphenylene ions , (C6F4)2+' are evident in several spectra . The appearance potentials of the major ions were obtatned from the ionisation efficiency curves. Attempts were made to correlate these to the effect of the central atom in substituent groups, but the large errors involved prevented the reaching of quantitative conclusions, although it would appear that the electron is removed from the ligand in the ionisation of t he parent molecule .

Spectral clustering independent component analysis for tissue classification from brain MRI

A spectral angle based feature extraction method, Spectral Clustering Independent Component Analysis (SC-ICA), is proposed in this work to improve the brain tissue classification from Magnetic Resonance Images (MRI). SC-ICA provides equal priority to global and local features; thereby it tries to resolve the inefficiency of conventional approaches in abnormal tissue extraction. First, input multispectral MRI is divided into different clusters by a spectral distance based clustering. Then, Independent Component Analysis (ICA) is applied on the clustered data, in conjunction with Support Vector Machines (SVM) for brain tissue analysis. Normal and abnormal datasets, consisting of real and synthetic T1-weighted, T2-weighted and proton density/fluid-attenuated inversion recovery images, were used to evaluate the performance of the new method. Comparative analysis with ICA based SVM and other conventional classifiers established the stability and efficiency of SC-ICA based classification, especially in reproduction of small abnormalities. Clinical abnormal case analysis demonstrated it through the highest Tanimoto Index/accuracy values, 0.75/98.8%, observed against ICA based SVM results, 0.17/96.1%, for reproduced lesions. Experimental results recommend the proposed method as a promising approach in clinical and pathological studies of brain diseases

Revised IR spectrum, radiative efficiency and global warming potential of nitrogen trifluoride

Nitrogen trifluoride (NF3) is an industrial gas used in the semiconductor industry as a plasma etchant and chamber cleaning gas. NF3 is an alternative to other potent greenhouse gases and its usage has increased markedly over the last decade. In recognition of its increased relevance and to aid planning of future usage we report an updated radiative efficiency and global warming potentials for NF3. Laboratory measurements give an integrated absorption cross section of 7.04 x 10(-17) cm(2) molecule(-1) cm(-1) over the spectral region 200 2000 cm(-1). The radiative efficiency is calculated to be 0.21 Wm(-2) ppbv(-1) and the 100 year GWP, relative to carbon dioxide, is 17200. These values are approximately 60% higher than previously published estimates, primarily reflecting the higher infrared absorption cross-sections reported here.

Fast and accurate SCFT calculations for periodic block-copolymer morphologies using the spectral method with Anderson mixing

We study the numerical efficiency of solving the self-consistent field theory (SCFT) for periodic block-copolymer morphologies by combining the spectral method with Anderson mixing. Using AB diblock-copolymer melts as an example, we demonstrate that this approach can be orders of magnitude faster than competing methods, permitting precise calculations with relatively little computational cost. Moreover, our results raise significant doubts that the gyroid (G) phase extends to infinite $\chi N$. With the increased precision, we are also able to resolve subtle free-energy differences, allowing us to investigate the layer stacking in the perforated-lamellar (PL) phase and the lattice arrangement of the close-packed spherical (S$_{cp}$) phase. Furthermore, our study sheds light on the existence of the newly discovered Fddd (O$^{70}$) morphology, showing that conformational asymmetry has a significant effect on its stability.

Can we measure terrestrial photosynthesis from space directly, using spectral reflectance and fluorescence?

Attempts to estimate photosynthetic rate or gross primary productivity from remotely sensed absorbed solar radiation depend on knowledge of the light use efficiency (LUE). Early models assumed LUE to be constant, but now most researchers try to adjust it for variations in temperature and moisture stress. However, more exact methods are now required. Hyperspectral remote sensing offers the possibility of sensing the changes in the xanthophyll cycle, which is closely coupled to photosynthesis. Several studies have shown that an index (the photochemical reflectance index) based on the reflectance at 531 nm is strongly correlated with the LUE over hours, days and months. A second hyperspectral approach relies on the remote detection of fluorescence, which is a directly related to the efficiency of photosynthesis. We discuss the state of the art of the two approaches. Both have been demonstrated to be effective, but we specify seven conditions required before the methods can become operational.

Modeling ocean primary production: sensitivity to spectral resolution of attenuation and absorption of light

Modeling the vertical penetration of photosynthetically active radiation (PAR) through the ocean, and its utilization by phytoplankton, is fundamental to simulating marine primary production. The variation of attenuation and absorption of light with wavelength suggests that photosynthesis should be modeled at high spectral resolution, but this is computationally expensive. To model primary production in global 3d models, a balance between computer time and accuracy is necessary. We investigate the effects of varying the spectral resolution of the underwater light field and the photosynthetic efficiency of phytoplankton (α∗), on primary production using a 1d coupled ecosystem ocean turbulence model. The model is applied at three sites in the Atlantic Ocean (CIS (∼60°N), PAP (∼50°N) and ESTOC (∼30°N)) to include the effect of different meteorological forcing and parameter sets. We also investigate three different methods for modeling α∗ – as a fixed constant, varying with both wavelength and chlorophyll concentration [Bricaud, A., Morel, A., Babin, M., Allali, K., Claustre, H., 1998. Variations of light absorption by suspended particles with chlorophyll a concentration in oceanic (case 1) waters. Analysis and implications for bio-optical models. J. Geophys. Res. 103, 31033–31044], and using a non-spectral parameterization [Anderson, T.R., 1993. A spectrally averaged model of light penetration and photosynthesis. Limnol. Oceanogr. 38, 1403–1419]. After selecting the appropriate ecosystem parameters for each of the three sites we vary the spectral resolution of light and α∗ from 1 to 61 wavebands and study the results in conjunction with the three different α∗ estimation methods. The results show modeled estimates of ocean primary productivity are highly sensitive to the degree of spectral resolution and α∗. For accurate simulations of primary production and chlorophyll distribution we recommend a spectral resolution of at least six wavebands if α∗ is a function of wavelength and chlorophyll, and three wavebands if α∗ is a fixed value.

Partial spectral projected gradient method with active-set strategy for linearly constrained optimization

A method for linearly constrained optimization which modifies and generalizes recent box-constraint optimization algorithms is introduced. The new algorithm is based on a relaxed form of Spectral Projected Gradient iterations. Intercalated with these projected steps, internal iterations restricted to faces of the polytope are performed, which enhance the efficiency of the algorithm. Convergence proofs are given and numerical experiments are included and commented. Software supporting this paper is available through the Tango Project web page: http://www.ime.usp.br/similar to egbirgin/tango/.

Spectral absorption properties of aerosol particles from 350-2500nm

The aerosol spectral absorption efficiency (alpha(a) in m(2)/g) is measured over an extended wavelength range (350-2500 nm) using an improved calibrated and validated reflectance technique and applied to urban aerosol samples from Sao Paulo, Brazil and from a site in Virginia, Eastern US, that experiences transported urban/industrial aerosol. The average alpha(a) values (similar to 3m(2)/g at 550 nm) for Sao Paulo samples are 10 times larger than a a values obtained for aerosols in Virginia. Sao Paulo aerosols also show evidence of enhanced UV absorption in selected samples, probably associated with organic aerosol components. This extra UV absorption can double the absorption efficiency observed from black carbon alone, therefore reducing by up to 50% the surface UV fluxes, with important implications for climate, UV photolysis rates, and remote sensing from space. Citation: Martins, J.V., P. Artaxo, Y.J. Kaufman, A.D. Castanho, and L.A. Remer (2009), Spectral absorption properties of aerosol particles from 350-2500nm, Geophys. Res. Lett., 36, L13810, doi: 10.1029/2009GL037435.

Use of high resolution digital multi-spectral imagery to assess the distribution of disease caused by Phytophthora cinnamomi on heathland at Anglesea, Victoria

Disease caused by the soilborne plant pathogen Phytophthora cinnamomi causes long-term floristic and structural changes in native vegetation communities in Australia. Key components of the management of this disease are to know where it occurs and the rate at which it spreads. The distribution of P. cinnamomi has generally been assessed as locality points of infestation and mapping the extent of diseased vegetation in any area is difficult and costly. This study was undertaken in P. cinnamomi-infested heathland communities in southern Victoria, Australia, where the symptoms of P. cinnamomi arise as a mosaic within healthy vegetation. We investigated the potential to improve the efficiency and effectiveness of mapping and monitoring vegetation affected by P. cinnamomi using digital multi-spectral imaging. This technique was developed for the purposes of monitoring vegetation and provides a single, seamless ortho-rectified digital image over the total area of interest. It is used to spatially quantify small differences in the characteristics of vegetation. In this study, the symptoms of disease caused by P. cinnamomi infestation were related to differences in the imagery and were used to map areas of infestation. Comparison of the digital multi-spectral imaging indications with on-ground observations gave moderate accuracy between the datasets (κ = 0.49) for disease and healthy indications. This study demonstrates the ability of the technique to determine disease extent over broad areas in native vegetation and provides a non-invasive, cost effective tool for management.

Spectral element modelling of wave propagation with boundary and structural discontinuity reflections

Spectral element method is very efficient in modelling high-frequency stress wave propagation because it works in the frequency domain. It does not need to use very fine meshes in order to capture high frequency wave energy as the time domain methods do, such as finite element method. However, the conventional spectral element method requires a throw-off element to be added to the structural boundaries to act as a conduit for energy to transmit out of the system. This makes the method difficult to model wave reflection at boundaries. To overcome this limitation, imaginary spectral elements are proposed in this study, which are combined with the real structural elements to model wave reflections at structural boundaries. The efficiency and accuracy of this proposed approach is verified by comparing the numerical simulation results with measured results of one dimensional stress wave propagation in a steel bar. The method is also applied to model wave propagation in a steel bar with not only boundary reflection, but also reflections from single and multiple cracks. The reflection and transmission coefficients, which are obtained from the discrete spring model, are adopted to quantify the discontinuities. Experimental tests of wave propagation in a steel bar with one crack of different depths are also carried out. Numerical simulations and experimental results show that the proposed method is effective and reliable in modelling wave propagation in one-dimensional waveguides with reflections from boundary and structural discontinuities. The proposed method can be applied to effectively model stress wave propagation for structural damage detection.

Nanostructured hybrid films containing nanophosphor: Fabrication and electronic spectral properties

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Efficiency of extrinsic and intrinsic charge-carrier photogeneration processes obtained from the steady-state photocurrent action spectra of poly(p-phenylene vinylene) derivatives

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Spectral redistribution of waveguided emission in BEH-PPV films

We report on spectral redistribution of the photoluminescence (PL) emission from the edge of thin-film planar waveguides of the conjugated polymer BEH-PPV [Poly(2,5-bis(2'-ethyl-hexyl)-1,4-phenylenevinylene] induced by self-absorption in the polymer film. The PL spectra present drastic changes and displace to longer wavelengths with increasing self-absorption. We observe an enhancement of the absolute PL intensity at longer wavelengths, which was interpreted as due to re-emission of self-absorbed photons. The significant efficiency for the PL re-emission suggests the use of self-absorption as a mechanism for tuning the emission into the near infrared.