Use of active personal dosemeters in interventional radiology and cardiology: Tests in laboratory conditions and recommendations - ORAMED project

Active personal dosemeters (APD) have been found to be very efficient tools to reduce occupational doses in many applications of ionizing radiation. In order to be used in interventional radiology and cardiology (IR/IC), APDs should be able to measure low energy photons and pulsed radiation with relatively high instantaneous personal dose equivalent rates. A study concerning the optimization of the use of APDs in IR/IC was performed in the framework of the ORAMED project, a Collaborative Project (2008-2011) supported by the European Commission within its 7th Framework Program. In particular, eight commercial APDs were tested in continuous and pulsed X-ray fields delivered by calibration laboratories in order to evaluate their performances. Most of APDs provide a response in pulsed mode more or less affected by the personal dose equivalent rate, which means they could be used in routine monitoring provided that correction factors are introduced. These results emphasize the importance of adding tests in pulsed mode in type-test procedures for APDs. Some general recommendations are proposed in the end of this paper for the selection and use of APDs at IR/IC workplaces.

The Use of Fly Ash in Highway Construction, HR-1031, 1990

In 1982 the Iowa DOT allowed a successful bidder the option of submitting materials and proportions using fly ash to produce a portland cement concrete (PCC) paving mixture to meet a specified compressive strength. The contractor, Irving F. Jensen, received approval for the use of a concrete mixture utilizing 500 lbs. of portland cement and 88 lbs. of fly ash as a replacement of 88 lbs. of portland cement. The PCC mixture was utilized on the Muscatine County US 61 relocation bypass paved as project F-61-4(32)--20-70. A Class "C" fly ash obtained from the Chillicothe electric generating plant approximately 100 miles away was used in the project. This use of fly ash in lieu of portland cement resulted in a cost savings of $64,500 and an energy savings of approximately 16 billion BTU. The compressive strength of this PCC mixture option was very comparable to concrete mixtures produced without the use of fly ash. The pavement has been performing very well. The substitution of fly ash for 15% of the cement has been allowed as a contractor's option since 1984. Due to the cost savings, it has been used in almost all Iowa PCC paving since that time.

The clinical use of quantitative ultrasound (QUS) in the detection and management of osteoporosis

For the detection and management of osteoporosis and osteoporosis-related fractures, quantitative ultrasound (QUS) is emerging as a relatively low-cost and readily accessible alternative to dual-energy X-ray absorptiometry (DXA) measurement of bone mineral density (BMD) in certain circumstances. The following is a brief, but thorough review of the existing literature with respect to the use of QUS in 6 settings: 1) assessing fragility fracture risk; 2) diagnosing osteoporosis; 3) initiating osteoporosis treatment; 4) monitoring osteoporosis treatment; 5) osteoporosis case finding; and 6) quality assurance and control. Many QUS devices exist that are quite different with respect to the parameters they measure and the strength of empirical evidence supporting their use. In general, heel QUS appears to be most tested and most effective. Overall, some, but not all, heel QUS devices are effective assessing fracture risk in some, but not all, populations, the evidence being strongest for Caucasian females over 55 years old. Otherwise, the evidence is fair with respect to certain devices allowing for the accurate diagnosis of likelihood of osteoporosis, and generally fair to poor in terms of QUS use when initiating or monitoring osteoporosis treatment. A reasonable protocol is proposed herein for case-finding purposes, which relies on a combined assessment of clinical risk factors (CR.F) and heel QUS. Finally, several recommendations are made for quality assurance and control.

The Use of Fly Ash in Highway Construction, HR-1031, Progress Report, 1986

In 1982 the Iowa DOT allowed a successful bidder the option of submitting materials and proportions using fly ash to produce a portland cement concrete (PCC) paving mixture to meet a specified compressive strength. The contractor, Irving F. Jensen, received approval for the use of a concrete mixture utilizing 500 lbs. of portland cement and 88 lbs. of fly ash as a replacement of 88 lbs. of portland cement. The PCC mixture was utilized on the Muscatine County US 61 relocation bypass paved as project F-61-4(32)--20-70. A Class "C" fly ash obtained from the Chillicothe electric generating plant approximately 100 miles away was used in the project. This use of fly ash in lieu of portland cement resulted in a cost savings of $64,500 and an energy savings of approximately 16 billion BTU. The compressive strength of this PCC mixture option was very comparable to concrete mixtures produced without the use of fly ash. The pavement has been performing very well. The substitution of fly ash for 15% of the cement has been allowed as a contractor's option since 1984. Due to the cost savings, it has been used in almost all Iowa PCC paving since that time.

Reduction of Greenhouse Gas Emissions in North-West Russia - Finnish Business Opportunities

Tutkimus suomalaisten yritysten liiketoimintamahdollisuuksista hiilidoksidipäästöjen vähentämisen parissa Luoteis-Venäjällä.

A pilot study on quantification of training load: The use of HRV in training practice.

Recent laboratory studies have suggested that heart rate variability (HRV) may be an appropriate criterion for training load (TL) quantification. The aim of this study was to validate a novel HRV index that may be used to assess TL in field conditions. Eleven well-trained long-distance male runners performed four exercises of different duration and intensity. TL was evaluated using Foster and Banister methods. In addition, HRV measurements were performed 5 minutes before exercise and 5 and 30 minutes after exercise. We calculated HRV index (TLHRV) based on the ratio between HRV decrease during exercise and HRV increase during recovery. HRV decrease during exercise was strongly correlated with exercise intensity (R = -0.70; p < 0.01) but not with exercise duration or training volume. TLHRV index was correlated with Foster (R = 0.61; p = 0.01) and Banister (R = 0.57; p = 0.01) methods. This study confirms that HRV changes during exercise and recovery phase are affected by both intensity and physiological impact of the exercise. Since the TLHRV formula takes into account the disturbance and the return to homeostatic balance induced by exercise, this new method provides an objective and rational TL index. However, some simplification of the protocol measurement could be envisaged for field use.

The reform of the European Energy Tax Directive reform : effect on prices

[spa] Para hacer frente a los riesgos relacionados con la contaminación atmosférica, es ampliamente aceptada la necesidad de instrumentos de política encaminados a reducir las emisiones. La intervención tiene por objeto reducir las conductas contaminantes y incentivar una conducta más respetuosa y el uso de tecnologías más eficientes. La Unión Europea cuenta con dos importantes mecanismos económicos para el control de emisiones a escala europea: la directiva sobre los impuestos energéticos, un instrumento de fiscalidad ambiental aprobado en 2003 que afecta el precio de los productos energéticos, y el sistema de comercio de los derechos de emisiones, introducido en 2005, que afecta directamente a la cantidad de emisiones de CO2. En 2011, la Comisión Europea propuso una nueva versión de la directiva sobre los impuestos energéticos. El objetivo principal de la propuesta es aumentar la eficacia del instrumento a través de una mayor presión fiscal sobre los productos energéticos y de coordinar este instrumento de fiscalidad medioambiental con el sistema de comercio de los derechos de emisiones, para establecer una señal de precio de CO2 coherente para todos los sectores. Sin embargo, en mayo de 2012 el Parlamento Europeo bloqueó la propuesta de la nueva versión del impuesto, y el proceso de actualización se detuvo. La preocupación principal parecía ser el efecto de dicha propuesta en la competitividad, en particular para los sectores que serían los más afectados dado el uso intensivo de los productos energéticos, como el sector del transporte. El objetivo de este estudio es analizar el efecto que la reforma de la directiva sobre los impuestos energéticos podría tener sobre el nivel de precios, en particular en los países de la Unión Europea donde esta reforma implicaría un aumento de los impuestos energéticos. Utilizando datos del proyecto “World Input-Output Database”, la principal conclusión es que el nuevo sistema de impuestos energéticos tendría un impacto muy bajo sobre los precios. Por lo tanto, dado que los precios no serían fuertemente afectados por la reforma, no habrá inconvenientes para la competitividad y implicaciones en términos de distribución, pero, por otro lado, este resultado también implica una baja capacidad de esta reforma para provocar cambios en el consumo y la producción hacia menos presiones ambientales.

The reform of the European Energy Tax Directive reform : effect on prices

[spa] Para hacer frente a los riesgos relacionados con la contaminación atmosférica, es ampliamente aceptada la necesidad de instrumentos de política encaminados a reducir las emisiones. La intervención tiene por objeto reducir las conductas contaminantes y incentivar una conducta más respetuosa y el uso de tecnologías más eficientes. La Unión Europea cuenta con dos importantes mecanismos económicos para el control de emisiones a escala europea: la directiva sobre los impuestos energéticos, un instrumento de fiscalidad ambiental aprobado en 2003 que afecta el precio de los productos energéticos, y el sistema de comercio de los derechos de emisiones, introducido en 2005, que afecta directamente a la cantidad de emisiones de CO2. En 2011, la Comisión Europea propuso una nueva versión de la directiva sobre los impuestos energéticos. El objetivo principal de la propuesta es aumentar la eficacia del instrumento a través de una mayor presión fiscal sobre los productos energéticos y de coordinar este instrumento de fiscalidad medioambiental con el sistema de comercio de los derechos de emisiones, para establecer una señal de precio de CO2 coherente para todos los sectores. Sin embargo, en mayo de 2012 el Parlamento Europeo bloqueó la propuesta de la nueva versión del impuesto, y el proceso de actualización se detuvo. La preocupación principal parecía ser el efecto de dicha propuesta en la competitividad, en particular para los sectores que serían los más afectados dado el uso intensivo de los productos energéticos, como el sector del transporte. El objetivo de este estudio es analizar el efecto que la reforma de la directiva sobre los impuestos energéticos podría tener sobre el nivel de precios, en particular en los países de la Unión Europea donde esta reforma implicaría un aumento de los impuestos energéticos. Utilizando datos del proyecto “World Input-Output Database”, la principal conclusión es que el nuevo sistema de impuestos energéticos tendría un impacto muy bajo sobre los precios. Por lo tanto, dado que los precios no serían fuertemente afectados por la reforma, no habrá inconvenientes para la competitividad y implicaciones en términos de distribución, pero, por otro lado, este resultado también implica una baja capacidad de esta reforma para provocar cambios en el consumo y la producción hacia menos presiones ambientales.

Bone Mineral Accrual in Physically Active Girls. With Special Reference to Reduction in Physical Activity Level and Use of Oral Contraceptives

Adolescence is an important time for acquiring high peak bone mass. Physical activity is known to be beneficial to bone development. The effect of estrogen-progestin contraceptives (EPC) is still controversial. Altogether 142 (52 gymnasts, 46 runners, and 42 controls) adolescent women participated in this study, which is based on two 7-year (n =142), one 6-year (n =140) and one 4-year (n =122) follow-ups. Information on physical activity, menstrual history, sexual maturation, nutrition, living habits and health status was obtained through questionnaires and interviews. The bone mineral density (BMD) and content (BMC) of lumbar spine (LS) and femoral neck (FN) were measured by dual- energy X-ray absoptiometry. Calcaneal sonographic measurements were also made. The physical activity of the athletes participating in this study decreased after 3-year follow-up. High-impact exercise was beneficial to bones. LS and FN BMC was higher in gymnasts than in controls during the follow-up. Reduction in physical activity had negative effects on bone mass. LS and FN BMC increased less in the group having reduced their physical activity more than 50%, compared with those continuing at the previous level (1.69 g, p=0.021; 0.14 g, p=0.015, respectively). The amount of physical activity was the only significant parameter accounting for the calcaneal sonography measurements at 6-year follow-up (11.3%) and reduced activity level was associated with lower sonographic values. Long-term low-dose EPC use seemed to prevent normal bone mass acquisition. There was a significant trend towards a smaller increase in LS and FN BMC among long-term EPC users. In conclusion, this study confirms that high-impact exercise is beneficial to bones and that the benefits are partly maintained even after a clear reduction in training level at least for 4 years. Continued exercise is needed to retain all acquired benefits. The bone mass gained and maintained can possibly be maximized in adolescence by implementing high-impact exercise for youngsters. The peak bone mass of the young women participating in the study may be reached before the age of 20. Use of low-dose EPCs seems to suppress normal bone mass acquisition.

Consumer valuation of energy-saving features of residential air conditioners with hedonic and choice models

The promotion of energy-efficient appliances is necessary to reduce the energetic and environmental burden of the household sector. However, many studies have reported that a typical consumer underestimates the benefits of energy-saving investment on the purchase of household electric appliances. To analyze this energy-efficiency gap problem, many scholars have estimated implicit discount rates that consumers use for energy-consuming durables. Although both hedonic and choice models have been used in previous studies, a comparison between two models has not yet been done. This study uses point of sale data about Japanese residential air conditioners and estimates implicit discounts rates with both hedonic and choice models. Both models demonstrate that a typical consumer underinvests in energy efficiency. Although choice models estimate a lower implicit discount rate than hedonic models, the latter models estimate the values of other product characteristics more consistently than choice models.

Use of sorghum straw (Sorghum bicolor) for second generation ethanol production: pretreatment and enzymatic hydrolysis

Agronomic biomass yields of forage sorghum BRS 655 presented similar results to other energy crops, producing 9 to 12.6 tons/ha (dry mass) of sorghum straw. The objective of this study was to evaluate the lignocellulosic part of this cultivar in terms of its potential in the different unit processes in the production of cellulosic ethanol, measuring the effects of pretreatment and enzymatic hydrolysis. Three types of pre-treatments for two reaction times were conducted to evaluate the characteristics of the pulp for subsequent saccharification. The pulp pretreated by alkali, and by acid followed by delignification, attained hydrolysis rates of over 90%.

The purpose and use of passenger ships in 2058 - Future scenarios generated by the Delphi method

The purpose of the thesis is to generate scenarios of future purposes and of use of ships, suitable for STX Finland Cruise Oy to design and build, over a 50 year time span by applying the Delphi method and an open innovation approach in a future workshop. The scenarios were mapped out with help of two Delphi survey rounds and one future workshop. The number of participants in both surveys and the workshop was some twenty experts in each, representing various fields. On the basis of the first survey round, four different subject areas were selected for analysis: purposes for the use of ships; energy efficiency of cruises and ships; cost efficiency of sea transportation and vacation; and the views and expectations of the customers in the future. As a result of the future workshop, four different themes were established, which were studied further during the second Delphi round. The themes are future service and operation concepts; versatile uses of the space in ships; communication of environmental benefits of ships, future energy solutions and social interaction between passengers onboard. In addition to generating the scenarios, further aim of the thesis is to implement the Delphi method and workshop activity as foresight tools for STX Europe and to produce a chart of a future shipbuilding foresight community to can serve the open innovation processes in the maritime cluster as a whole.

Evaluation of energy efficiency and best available techniques in pumping processes

The potential for enhancing the energy efficiency of industrial pumping processes is estimated to be in some cases up to 50 %. One way to define further this potential is to implement techniques in accordance to definition of best available techniques in pumping applications. These techniques are divided into three main categories: Design, control method & maintenance and distribution system. In the theory part of this thesis first the definition of best available techniques (BAT) and its applicability on pumping processes is issued. Next, the theory around pumping with different pump types is handled, the main stress being in centrifugal pumps. Other components needed in a pumping process are dealt by presenting different control methods, use of an electric motor, variable speed drive and the distribution system. Last part of the theory is about industrial pumping processes from water distribution, sewage water and power plant applications, some of which are used further on in the empirical part as example cases. For the empirical part of this study four case studies on typical pumping processes from older Master’s these were selected. Firstly the original results were analyzed by studying the distribution of energy consumption between different system components and using the definition of BAT in pumping, possible ways to improve energy efficiency were evaluated. The goal in this study was that by the achieved results it would be possible to identify the characteristic energy consumption of these and similar pumping processes. Through this data it would then be easier to focus energy efficiency actions where they might be the most applicable, both technically and economically.

Developing markets of energy biomass – local and global perspectives

The thesis explores global and national-level issues related to the development of markets for biomass for energy. The thesis consists of five separate papers and provides insights on selected issues. The aim of Paper I was to identify methodological and statistical challenges in assessing international solid and liquid biofuels trade and provide an overview of the Finnish situation with respect to the status of international solid and liquid biofuels trade. We found that, for the Finnish case, it is possible to qualify direct and indirect trade volumes of biofuels. The study showed that indirect trade of biofuels has a highly significant role in Finland and may be a significant sector also in global biofuels trade. The purpose of Paper II was to provide a quantified insight into Finnish prospects for meeting the national 2020 renewable energy targets and concurrently becoming a largescale producer of forest-biomass-based second-generation biofuels for feeding increasing demand in European markets. We found that Finland has good opportunities to realise a scenario to meet 2020 renewable energy targets and for large-scale production of wood-based biofuels. The potential net export of transport biofuels from Finland in 2020 would correspond to 2–3% of European demand. Paper III summarises the global status of international solid and liquid biofuels trade as illuminated by several separate sources. International trade of biofuels was estimated at nearly 1 EJ for 2006. Indirect trade of biofuels through trading of industrial roundwood and material by-products comprises the largest proportion of the trading, with a share of about two thirds. The purpose of Paper IV was to outline a comprehensive picture of the coverage of various certification schemes and sustainability principles relating to the entire value-added chain of biomass and bioenergy. Regardless of the intensive work that has been done in the field of sustainability schemes and principles concerning use of biomass for energy, weaknesses still exist. The objective of Paper V was to clarify the alternative scenarios for the international biomass market until 2020 and identify the underlying steps needed toward a wellfunctioning and sustainable market for biomass for energy purposes. An overall conclusion drawn from this analysis concerns the enormous opportunities related to the utilisation of biomass for energy in the coming decades.

Seasonality of net radiation in two sub-basins of Paracatu by the use of modis sensor products

The net radiation (Rn) represents the main source of energy for physical and chemical processes that occur in the surface-atmosphere interface, and it is used for air and soil heating, water transfer, in the form of vapor from the surface to the atmosphere, and for the metabolism of plants, especially photosynthesis. If there is no record of net radiation in certain areas, the use of information is important to help determine it. Among them we can highlight those provided by remote sensing. In this context, this work aims to estimate the net radiation, with the use of products of MODIS sensor, in the sub-basins of Entre Ribeiros creek and Preto River, located between the Brazilian states of Goiás and Minas Gerais. The SEBAL (Surface Energy Balance Algorithm for Land) was used to obtain the Rn in four different days in the period of July to October, 2007. The Rn results obtained were consistent with others cited in the literature and are important because the orbital information can help determine the Rn in areas where there are not automatic weather stations to record the net radiation.