Characterization of wood biochar and evaluation of its adsorption potential for removal of sulphate from produced water in offshore oil and gas industry

This thesis analyses the potential of wood biochar as an adsorbent in removal of sulphate from produced water. In worldwide offshore oil and gas industry, a large volume of waste water is generated as produced water. Sulphur compounds present in these produced water streams can cause environmental problems, regulatory problems and operational issues. Among the various sulphur removal technologies, the adsorption technique is considered as a suitable method since the design is simple, compact, economical and robust. Biochar has been studied as an adsorbent for removal of contaminants from water in a number of studies due to its low cost, potential availability, and adsorptive characteristics. In this study, biochar produced through fast pyrolysis of bark, hardwood sawdust, and softwood sawdust were characterized through a series of tests and were analysed for adsorbent properties. Treating produced water using biochar sourced from wood waste is a two-fold solution to environmental problems as it reduces the volume of these wastes. Batch adsorption tests were carried out to obtain adsorption capacities of each biochar sample using sodium sulphate solutions. The highest sulphur adsorption capacities obtained for hardwood char, softwood char and bark char were 11.81 mg/g, 9.44 mg/g, and 7.94 mg/g respectively at 10 °C and pH=4. The adsorption process followed the second order kinetic model and the Freundlich isotherm model. Adsorption reaction was thermodynamically favourable and exothermic. The overall analysis concludes that the wood biochar is a feasible, economical, and environmental adsorbent for removal of sulphate from produced water.

2003 Habitat Maps derived from Grey Nurse Shark (GNS) Project of Wolf Rock, Double Island Point, Queensland, Australia

Surveying habitats critical to the survival of grey nurse sharks in South-East Queensland has mapped critical habitats, gathered species inventories and developed protocols for ecological monitoring of critical habitats in southern Queensland. This information has assisted stakeholders with habitat definition and effective management. In 2002 members of UniDive applied successfully for World Wide Fund for Nature, Threatened Species Network funds to map the critical Grey Nurse Shark Habitats in south east Queensland. UniDive members used the funding to survey, from the boats of local dive operators, Wolf Rock at Double Island Point, Gotham, Cherub's Cave, Henderson's Rock and China Wall at North Moreton and Flat Rock at Point Look Out during 2002 and 2003. These sites are situated along the south east Queensland coast and are known to be key Grey Nurse Shark aggregation sites. During the project UniDive members were trained in mapping and survey techniques that include identification of fish, invertebrates and substrate types. Training was conducted by experts from the University of Queensland (Centre of Marine Studies, Biophysical Remote Sensing) and the Queensland Parks and Wildlife Service who are also UniDive members. The monitoring methods (see methods) are based upon results of the UniDive Coastcare project from 2002, the international established Reef Check program and research conducted by Biophysical Remote Sensing and the Centre of Marine Studies. Habitats were mapped using a combination of towed GPS photo transects, aerial photography, bathymetry surveys and expert knowledge. This data provides georeferenced information regarding the major features of each of Sites mapped including Wolf Rock

From F energy rating to Nearly ZEB: project of energy retrofit and architectural upgrade of a brick terraced house in Co. Dublin, Ireland

Questo progetto è stato sviluppato durante un periodo di ricerca presso il Dipartimento di Ingegneria Civile del Trinity College e continuato presso l’Università di Bologna. Il progetto ha l’obiettivo di analizzare le soluzioni per l’ampliamento, la sostituzione degli impianti e l’ottimizzazione energetica di un tipico edificio residenziale Irlandese, una end of terrace in mattoni costruita negli anni ’20, collocata a Blackrock (Dublino). Diversi studi sostengono che lo stock abitativo irlandese è il peggiore del nord Europa per quanto riguarda la performance energetica. Questa tesi consta di una prima parte di studio del contesto e delle tecniche costruttive tradizionali irlandesi; è presente un capitolo di approfondimento sulle leggi riguardanti le costruzioni e gli incentivi forniti dal governo irlandese per interventi di retrofit energetico. Il terzo capitolo è un’analisi dell'esistente, con disegni del rilievo geometrico, immagini dell’edificio originale, termogrammi e dati riguardanti l’attuale performance energetica. Vengono poi mostrate diverse ipotesi di progetto e, una volta determinata la disposizione degli spazi interni, vengono considerate due soluzioni simili, ma costruite con pacchetti costruttivi diversi. Nel Progetto A l’involucro dell’addizione ha una struttura in muratura, nel Progetto B la struttura è in X-lam. Le performance energetiche delle due proposte vengono confrontate tramite una simulazione attuata grazie all'utilizzo del software dinamico IES-VE. Viene valutata l’applicazione di energie rinnovabili, quali l’energia solare e eolica e l’apporto che queste possono dare al bilancio energetico. Infine viene fatta un’analisi dei costi, valutando possibili suddivisioni dei lavori e ipotizzando un piano di ritorno dell’investimento, anche in combinazione con l’applicazione di energie rinnovabili. Alla fine del progetto si trova una valutazione quantitativa dei miglioramenti dell’edificio e un’analisi critica dei limiti del progetto.

INTERACTIVE EFFECTS OF CLIMATE CHANGE AND FUNGAL COMMUNITIES ON THE DECOMPOSITION OF WOOD-DERIVED CARBON IN FOREST SOILS

Soils are the largest sinks of carbon in terrestrial ecosystems. Soil organic carbon is important for ecosystem balance as it supplies plants with nutrients, maintains soil structure, and helps control the exchange of CO2 with the atmosphere. The processes in which wood carbon is stabilized and destabilized in forest soils is still not understood completely. This study attempts to measure early wood decomposition by different fungal communities (inoculation with pure colonies of brown or white rot, or the original microbial community) under various interacting treatments: wood quality (wood from +CO2, +CO2+O3, or ambient atmosphere Aspen-FACE treatments from Rhinelander, WI), temperature (ambient or warmed), soil texture (loamy or sandy textured soil), and wood location (plot surface or buried 15cm below surface). Control plots with no wood chips added were also monitored throughout the study. By using isotopically-labelled wood chips from the Aspen-FACE experiment, we are able to track wood-derived carbon losses as soil CO2 efflux and as leached dissolved organic carbon (DOC). We analyzed soil water for chemical characteristics such as, total phenolics, SUVA254, humification, and molecular size. Wood chip samples were also analyzed for their proportion of lignin:carbohydrates using FTIR analysis at three time intervals throughout 12 months of decomposition. After two years of measurements, the average total soil CO2 efflux rates were significantly different depending on wood location, temperature, and wood quality. The wood-derived portion soil CO2 efflux also varied significantly by wood location, temperature, and wood quality. The average total DOC and the wood-derived portion of DOC differed between inoculation treatments, wood location, and temperature. Soil water chemical characteristics varied significantly by inoculation treatments, temperature, and wood quality. After 12 months of decomposition the proportion of lignin:carbohydrates varied significantly by inoculation treatment, with white rot having the only average proportional decrease in lignin:carbohydrates. Both soil CO2 efflux and DOC losses indicate that wood location is important. Carbon losses were greater from surface wood chips compared with buried wood chips, implying the importance of buried wood for total ecosystem carbon stabilization. Treatments associated with climate change also had an effect on the level of decomposition. DOC losses, soil water characteristics, and FTIR data demonstrate the importance of fungal community on the degree of decomposition and the resulting byproducts found throughout the soil.

When the virtual influences reality. The conservation project of the toledo gate in ciudad real (Spain)

The Toledo Gate of Ciudad Real, Spain, constructed between the late 13th and early 14th centuries, is the last remaining portion of a once complete medieval city wall. It represents the long history of the city and constitutes its main heritage symbol, dividing the historic city centre from the later 19th and 20th century expansions. In October 2012, the Town Hall and the Montemadrid Foundation started the conservation works to preserve this important monument. The preliminary phase of this project included an in-depth series of scientific studies which were carried out by a multidisciplinary team focusing on archival research, historic investigations, archaeological excavations as well as material composition analysis and main treatment application tests. As a result of these studies a series of virtual 3D models were created to inform, discuss and study the monument. A first digital model permitted visualization of the gate in the 19th century and how the main entrance to the city was integrated as a fundamental part of the city walls. This virtual reconstruction also became an important part of the campaign to raise awareness among the citizens towards a monument that had remained in the shadows for the last century, isolated in a roundabout after the systematic demolition of the city walls in the late 19th century. Over the last three years and as a result of these archaeological and historic investigations and subsequent virtual models, surprisingly new and interesting data were brought to light thus permitting the establishment and corroboration of a new and updated hypothesis of the Toledo Gate that goes beyond the previous ideas. As a result of these studies a new architectural typology with construction techniques of has been suggested. This paper describes how the results of this continuous and interdisciplinary documentation process have benefitted from a computer graphic reconstruction of the gate. It highlights how virtual reconstruction can be a powerful tool for conservation decision making and awareness raising. Furthermore, the interesting results of the final reconstruction hypothesis convinced the technical team responsible for the conservation to alter some aspects of the final project physical interventions in order to focus on some of the features and conclusions discovered through the virtual model study.

Lighting ambiances and materialities of wood in architecture: a comparative evaluation of the quality of spaces in relation to interior finishes

Le bois est un matériau souvent utilisé par les architectes pour améliorer l’ambiance générale d’un espace, mais peu de recherches en présentent l’impact réel du matériau sur les impressions visuelles et les effets lumineux. Cette recherche étudie l’influence de la matérialité du bois par rapport à la création d’ambiances d’éclairage spécifiques dans l’architecture. Plus particulièrement, elle se concentre sur l’impact des panneaux décoratifs en bois à générer de la diversité lumineuse dans les espaces intérieurs et son potentiel à améliorer la satisfaction environnementale et l’efficacité énergétique. La recherche utilise des maquettes à l’échelle pour leur précision dans la représentation des ambiances lumineuses d’espaces éclairés naturellement ainsi que les technologies récentes d’imagerie digitale pour capturer et analyser les résultats. La méthodologie permet la comparaison entre les différents réglages des espaces intérieurs créés par une sélection des types de matérialités du bois: la réflectance (valeur), la couleur et la réflectivité. Les modalités spatiales sont comparées en présence d’ensoleillement direct et sous des conditions de ciel couvert puisque les modèles d’éclairage et les ambiances diffèrent considérablement. Les résultats permettent d’établir une discussion sur les ambiances en termes de brillance et de contraste, sur la couleur ainsi que la répartition des zones lumineuses dans l’espace. La recherche souligne le rôle des matérialités que peuvent prendre le bois pour optimiser la diversité lumineuse et la création d’ambiances visuellement confortables, ainsi que ses possibilités d’améliorer les ambiances architecturales par rapport à la lumière.

Performance and quality of wood in a clone of Eucalyptus in monoculture and silvipastoral system.

Este trabalho foi desenvolvido com o objetivo de avaliar e comparar o desempenho e as variações na qualidade da madeirade árvores de eucalipto implantadas em sistema silvipastoril e em monocultivo. Os dados foram coletados em 13 árvores amostras aos 36 meses de idade, selecionadas em função do intervalo de confiança da média dos diâmetros a altura do peito (DAP), e da posição das árvores na faixa de plantio no sistema silvipastoril, com face de exposição sul, norte e central. Foram avaliadas as variáveis DAP, altura total e altura comercial, volume e conicidade do tronco, densidade básica e deslocamento da medula. Concluiu-se que no sistema silvipastoril as árvores apresentaram maior DAP, menor altura total e maior conicidade do tronco que no monocultivo. O DAP não diferiu em relação à posição na faixa de plantio, porém as árvores com face de exposição norte foram mais baixas e cônicas. A densidade básica e o deslocamento da medula não foram influenciados pelo sistema de cultivo.

Influence of the wood mechanical properties in the dovetail joint behavior

The force distribution inside a dovetail joint is complex. Wood is simultaneously loaded in different directions in the several connected surfaces. The analytical solutions available for the analysis of the behavior of those carpentry joints rely on the mechanical properties of wood. In particular, the stiffness properties of wood under compression are crucial for the forces equilibrium. Simulations showed that the stiffness values considered in each of the springs normally assumed in the analytical models, have great influence in the bearing capacity and stiffness of the dovetail joints, with important consequence on the stress distribution over the overall structure. In a wide experimental campaign, the properties under compression of the most common wood species of existing timber structures have been determined. Then, a solved example of a dovetail joint is presented assuming different wood species and the corresponding strength and stiffness properties values obtained in the tests.

Cutting of Frozen Wood

The objective of this master's thesis was to develop a system for measuring the cutting forces of frozen wood. In northern parts of the world cuttingof frozen wood is one of the major problem. During winter and early spring the temperature inside the wood cells will fall below Zero degrees that strongly influences on the properties of the wood. These variations of properties will effects on the blade nomenclature while cutting the frozen wood. However the end results will cause uneven cutting forces. Cutting forces, Chip formation, wearing of the blade and the quality of the machined surface are difficult task. In this project we are attempting to find the variation of cutting forces and properties of frozen wood at four different temperatures (-20 , -10, 0 and + 10 degrees). The linear planning machine was used for measuring the cuttingforces. The cutting was done parallel to the long axis of wood due to the nature of pine wood and the structure of the plane. A considerable amount of work andtime was used for collecting and processing the numerical information from the sensors of the measuring system. There were some alterations suggested to the construction of the plane and the sensor system.

Conditions and practices in the commercialisation of innovations in wood industry

The report 'Conditions and practices in the commercialisation of innovation in wood industry' has been written as a part of the Wood Academy project. The report analyses the commercialisation conditions and practices of wood industry by utilising product categorisation based on a conceptual schema which combines the aspects of the transfer of the procession of utility and the degree of form/service utility (or value-added) created or provided by the company. Open innovation approaches help to perceive the possible new product and service innovations as well as the new business models and earning logics in the industry. The report also contains brief company cases to demonstrate theory-to-practice and showcase company examples from successful Finnish companies.

Comparison of mechanical properties of tension and opposite wood in Populus

In this paper we focused on the differences of mechanical properties of tension and normal wood of 1-year-old poplar trees, artificially tilted. Elastic and fracture properties have been measured and linked to the anatomy. Tension wood is well known because it prevents good surface finishing and leads to difficulties with sawing. We studied three main mechanical properties: young modulus, energy of cutting and longitudinal residual strain of maturation (with strain gauges) because of their importance in wood technology. Moreover, this work takes place in a larger project of study, the phenomena of axes re-orientation in trees (allowing by the production of reaction wood), where these data are required for biomechanical modelling. The results show that tension wood has a higher young modulus, needs a higher energy to be cut and exhibited a higher level of longitudinal residual strain of maturation than those of normal wood. The results suggest that these differences require deeper analysis of the wood than anatomy: measurement of microfibril orientation in the S2 layer and also the lignin composition in monomeric units.

Effects of elevated atmospheric CO2 and O3 on wood density, antomical proerties and decomposition of Northern Hardwoods

Anthropogenic activities continue to drive atmospheric CO2 and O3 concentrations to levels higher than during the pre-industrial era. Accumulating evidence indicates that both elevated CO2 and elevated O3 could modify the quantity and biochemistry of woody plant biomass. Anatomical properties of woody plants are largely influenced by the activity of the cambium and the growth characteristics of wood cells, which are in turn influenced by a range of environmental factors. Hence, alterations in the concentrations of atmospheric CO2 and / or O3 could also impact wood anatomical properties. Many fungi derive their metabolic resources for growth from plant litter, including woody tissue, and therefore modifications in the quantity, biochemistry and anatomical properties of woody plants in response to elevated CO2 and / or O3 could impact the community of wood-decaying fungi and rates of wood decomposition. Consequently carbon and nutrient cycling and productivity of terrestrial ecosystem could also be impacted. Alterations in wood structure and biochemistry of woody plants could also impact wood density and subsequently impact wood quality. This dissertation examined the long term effects of elevated CO2 and / or O3 on wood anatomical properties, wood density, wood-decaying fungi and wood decomposition of northern hardwood tree species at the Aspen Free-Air CO2 and O3 Enrichment (Aspen FACE) project, near Rhinelander, WI, USA. Anatomical properties of wood varied significantly with species and aspen genotypes and radial position within the stem. Elevated CO2 did not have significant effects on wood anatomical properties in trembling aspen, paper birch or sugar maple, except for marginally increasing (P < 0.1) the number of vessels per square millimeter. Elevated O3 marginally or significantly altered vessel lumen diameter, cell wall area and vessel lumen area proportions depending on species and radial position. In line with the modifications in the anatomical properties, elevated CO2 and O3, alone, significantly modified wood density but effects were species and / or genotype specific. However, the effects of elevated CO2 and O3, alone, on wood anatomical properties and density were ameliorated when in combination. Wood species had a much greater impact on the wood-decaying fungal community and initial wood decomposition rate than did growth or decomposition of wood in elevated CO2 and / or O3. Polyporales, Agaricales, and Russulales were the dominant orders of fungi isolated. Based on the current results, future higher levels of CO2 and O3 may have moderate effects on wood quality of northern hardwoods, but for utilization purposes these may not be considered significant. However, wood-decaying fungal community composition and decomposition of northern hardwoods may be altered via shifts in species and / or genotype composition under future higher levels of CO2 and O3.

An investigation of contaminant distribution in subsurface marine wood waste at Mill-A South Terminal, Port of Everett, Washington

This project investigates the correlation between contaminants and the wood waste present in marine sediments off the shore of the Port of Everett in the former Weyerhaeuser Mill-A pulp mill site. The investigation includes the results of two field studies, which tested contaminant levels in 22 boreholes as well as several surface samples. The contaminants include heavy metals and wood waste byproducts. These results, along with 14 other bore logs, provide the framework for a three-dimensional site model, interpolating the full extent of the depositional units and organic and inorganic chemicals found at Mill-A. The sediments of interest are divided into five depositional units defined by the percent wood content and type of wood: native material (<5% wood), intermediate (<30% wood), sawdust (<30% wood), woodchips (<30% wood), and poorly sorted sands with silt (SM-SP) (0% wood). The contaminants include arsenic, 2,4-dimethylphenol, and total organic carbon. Three-dimensional modeling software, RockWorks, interpolated the discrete borehole data of sediment and contaminants assuming horizontal continuity between sampling locations. The sediment distribution was calculated within concentration ranges for each contaminant of concern. The lowest detection limits, the screening levels, and the cleanup levels defined these ranges. Total organic carbon served as a proxy to estimate the quantity of wood waste in the sediment. As a known byproduct of wood decomposition, 2,4-dimethylphenol was expected to be more prevalent in the depositional units with more wood waste. Finally, arsenic was a proxy for other contaminants to determine if contaminants at Mill-A are dominant in sediments with high percentages of wood waste. The volumetric distribution established that high levels of total organic carbon are present in the sediment with higher percentages of wood waste. This correlation was stronger in the decomposing sawdust-rich sediment than the woodchip-rich sediment. The 2,4-dimethylphenol concentrations above cleanup standards were dominant in the sawdust-rich, intermediate and native sediments. Concentrations of 2,4-dimethylphenol below cleanup levels characterized the native sediment. The distribution of arsenic showed no statistically significant correlation to wood content in sediment. These results do not support the hypothesis of contaminant-rich wood waste, as many of the high concentrations of contaminants were not in the wood-rich sediments. This suggests that the contaminants are more distributed among all depositional units at Mill-A rather than focused within sediments with a high percent of wood waste. Understanding the distribution of potentially toxic compounds with wood waste is important for restoring the Puget Sound waterways to a more habitable environment. Future studies should include new data to validate these results and to limit the uncertainty of the extent of contaminants. Future studies may also find motive in looking for a correlation between contaminants and grain size based on previous studies linking these characteristics. These investigations will benefit the current cleanup effort as well as future cleanup efforts at similarly contaminated waterways.

The structural and mechanical integrity of historic wood

Little is known about historic wood as it ages naturally. Instead, most studies focus on biological decay, as it is often assumed that wood remains otherwise stable with age. This PhD project was organised by Historic Scotland and the University of Glasgow to investigate the natural chemical and physical aging of wood. The natural aging of wood was a concern for Historic Scotland as traditional timber replacement is the standard form of repair used in wooden cultural heritage; replacing rotten timber with new timber of the same species. The project was set up to look at what differences could exist both chemically and physically between old and new wood, which could put unforeseen stress on the joint between them. Through Historic Scotland it was possible to work with genuine historic wood from two species, Oak and Scots pine, both from the 1500’s, rather than relying on artificial aging. Artificial aging of wood is still a debated topic, with consideration given to whether it is truly mimicking the aging process or just damaging the wood cells. The chemical stability of wood was investigated using Fourier-transform infrared (FTIR) microscopy, as well as wet chemistry methods including a test for soluble sugars from the possible breakdown of the wood polymers. The physical properties assessed included using a tensile testing machine to uncover possible differences in mechanical properties. An environmental chamber was used to test the reaction to moisture of wood of different ages, as moisture is the most damaging aspect of the environment to wooden cultural objects. The project uncovered several differences, both physical and chemical, between the modern and historic wood which could affect the success of traditional ‘like for like’ repairs. Both oak and pine lost acetyl groups, over historic time, from their hemicellulose polymers. This chemical reaction releases acetic acid, which had no effect on the historic oak but was associated with reduced stiffness in historic pine, probably due to degradation of the hemicellulose polymers by acid hydrolysis. The stiffness of historic oak and pine was also reduced by decay. Visible pest decay led to loss of wood density but there was evidence that fungal decay, extending beyond what was visible, degraded the S2 layer of the pine cell walls, reducing the stiffness of the wood by depleting the cellulose microfibrils most aligned with the grain. Fungal decay of polysaccharides in pine wood left behind sugars that attracted increased levels of moisture. The degradation of essential polymers in the wood structure due to age had different impacts on the two species of wood, and raised questions concerning both the mechanism of aging of wood and the ways in which traditional repairs are implemented, especially in Scots pine. These repairs need to be done with more care and precision, especially in choosing new timber to match the old. Within this project a quantitative method of measuring the microfibril angle (MFA) of wood using polarised Fourier transform infrared (FTIR) microscopy has been developed, allowing the MFA of both new and historic pine to be measured. This provides some of the information needed for a more specific match when selecting replacement timbers for historic buildings.