Adaptive multiscale principal components analysis for online monitoring of wastewater treatment

Fault detection and isolation (FDI) are important steps in the monitoring and supervision of industrial processes. Biological wastewater treatment (WWT) plants are difficult to model, and hence to monitor, because of the complexity of the biological reactions and because plant influent and disturbances are highly variable and/or unmeasured. Multivariate statistical models have been developed for a wide variety of situations over the past few decades, proving successful in many applications. In this paper we develop a new monitoring algorithm based on Principal Components Analysis (PCA). It can be seen equivalently as making Multiscale PCA (MSPCA) adaptive, or as a multiscale decomposition of adaptive PCA. Adaptive Multiscale PCA (AdMSPCA) exploits the changing multivariate relationships between variables at different time-scales. Adaptation of scale PCA models over time permits them to follow the evolution of the process, inputs or disturbances. Performance of AdMSPCA and adaptive PCA on a real WWT data set is compared and contrasted. The most significant difference observed was the ability of AdMSPCA to adapt to a much wider range of changes. This was mainly due to the flexibility afforded by allowing each scale model to adapt whenever it did not signal an abnormal event at that scale. Relative detection speeds were examined only summarily, but seemed to depend on the characteristics of the faults/disturbances. The results of the algorithms were similar for sudden changes, but AdMSPCA appeared more sensitive to slower changes.

Productivity growth in Australian manufacturing sector: some new evidence

This article examines the productivity performance of Australia's manufacturing sector by decomposing its output growth into input growth, technological progress and gains in technical efficiency. This three-way decomposition is done with an improved version of the stochastic frontier model using eight, two-digit industry level data from 1968/9 to 1994/5. Empirical evidence shows that input growth fueled output growth from 1968/9 to 1973/4, but since then, total factor productivity (TFP) growth has been the main contributor of output growth. While the trend of TFP growth was found to be promising for most industries with positive and increasing technological progress, the negative gains from technical efficiency over time is however cause for concern.

Productivity growth in pre-1990 Mongolian agriculture: Spiralling disaster or emerging success?

The reasons for the spectacular collapse of so many centrally-planned economies are a source of ongoing debate. In this paper, we use detailed farm-level data to measure total factor productivity (TFP) changes in Mongolian grain and potato farming during the 14-year period immediately preceding the 1990 economic reforms. We measure TFP growth using stochastic frontier analysis (SFA) and data envelopment analysis (DEA) methods. Our results indicate quite poor overall performance, with an average annual TFP change of - 1.7% in grain and 0.8% in potatoes, over the 14-year period. However, the pattern of TFP growth changed substantially during this period, with TFP growth exceeding 7% per year in the latter half of this period. This suggests that the new policies of improved education, greater management autonomy, and improved incentives, which were introduced in final two planning periods in the 1980s, were beginning to have a significant influence upon the performance of Mongolian crop farming. Crown Copyright (C) 2002 Published by Elsevier Science B.V. All rights reserved.

Analysis of genetic diversity within Australian lucerne cultivars and implications for future genetic improvement

Lucerne (Medicago sativa L.) is autotetraploid, and predominantly allogamous. This complex breeding structure maximises the genetic diversity within lucerne populations making it difficult to genetically discriminate between populations. The objective of this study was to evaluate the level of random genetic diversity within and between a selection of Australian-grown lucerne cultivars, with tetraploid M. falcata included as a possible divergent control source. This diversity was evaluated using random amplified polymorphic DNA (RAPDs). Nineteen plants from each of 10 cultivars were analysed. Using 11 RAPD primers, 96 polymorphic bands were scored as present or absent across the 190 individuals. Genetic similarity estimates (GSEs) of all pair-wise comparisons were calculated from these data. Mean GSEs within cultivars ranged from 0.43 to 0.51. Cultivar Venus (0.43) had the highest level of intra-population genetic diversity and cultivar Sequel HR (0.51) had the lowest level of intra-population genetic diversity. Mean GSEs between cultivars ranged from 0.31 to 0.49, which overlapped with values obtained for within-cultivar GSE, thus not allowing separation of the cultivars. The high level of intra- and inter-population diversity that was detected is most likely due to the breeding of synthetic cultivars using parents derived from a number of diverse sources. Cultivar-specific polymorphisms were only identified in the M. falcata source, which like M. sativa, is outcrossing and autotetraploid. From a cluster analysis and a principal components analysis, it was clear that M. falcata was distinct from the other cultivars. The results indicate that the M. falcata accession tested has not been widely used in Australian lucerne breeding programs, and offers a means of introducing new genetic diversity into the lucerne gene pool. This provides a means of maximising heterozygosity, which is essential to maximising productivity in lucerne.

Yield response of rice (Oryza sativa L.) genotypes to different types of drought under rainfed lowlands - Part 1. Grain yield and yield components

Responses of rice genotypes to drought stress may be different when characteristics of the drought stress environments differ. The performance of 128 genotypes was examined under irrigation and four different types of drought stress, to determine genotypic consistency in yield and factors determining yields under different drought stress conditions. The different drought conditions were mild drought during grain filling, short and severe drought at flowering, prolonged severe drought during the reproductive to grain filling, and prolonged mild drought during vegetative and grain filling. Genotypic grain yield under mild stress conditions was associated with yield under irrigated conditions, indicating the importance of potential yield in environments where the yield reduction was less than 50%. However, yields under irrigated conditions differed over time and locations. Under prolonged or severe drought conditions, flowering time was an important determinant of grain yield. Earlier flowering genotypes escaped the severe stress and had higher grain yields indicating large genotype by environment (G x E) interactions which have implications for plant breeding even for mild stress. It is suggested that variations in flowering time, potential yields and drought patterns need to be considered for development of drought-resistant cultivars using specific physiological traits. (C) 2002 Elsevier Science B.V. All rights reserved.

Effects of seawater components on immature Culicoides molestus (Skuse) (Diptera : Ceratopogonidae)

Following analysis of beach sites and an indication that seawater components might influence larval occurrence, we studied the impact of increasing salinity and seawater concentration on survival of fourth-instar larvae of the canal biting midge, Culicoides molestus . While NaCl had little effect on immature survival, increasing the concentration of seawater increased mortality prior to the adult stage. Seawater at three and four times the normal concentration killed all immatures. Artificial elevation of seawater concentration in the sandy substrate preferred by larvae, therefore, has the potential to reduce immature midge survival. Diet also affected survival, with higher mortality of immatures that were fed fish-food flakes compared with those that were fed live nematodes.

Tool support for testing concurrent Java components

Concurrent programs are hard to test due to the inherent nondeterminism. This paper presents a method and tool support for testing concurrent Java components. Too[ support is offered through ConAn (Concurrency Analyser), a too] for generating drivers for unit testing Java classes that are used in a multithreaded context. To obtain adequate controllability over the interactions between Java threads, the generated driver contains threads that are synchronized by a clock. The driver automatically executes the calls in the test sequence in the prescribed order and compares the outputs against the expected outputs specified in the test sequence. The method and tool are illustrated in detail on an asymmetric producer-consumer monitor. Their application to testing over 20 concurrent components, a number of which are sourced from industry and were found to contain faults, is presented and discussed.

A yield architecture framework to explain adaptation of pearl millet to environmental stress

Functional knowledge of the physiological basis of crop adaptation to stress is a prerequisite for exploiting specific adaptation to stress environments in breeding programs. This paper presents an analysis of yield components for pearl millet, to explain the specific adaptation of local landraces to stress environments in Rajasthan, India. Six genotypes, ranging from high-tillering traditional landraces to low-tillering open-pollinated modern cultivars, were grown in 20 experiments, covering a range of nonstress and drought stress patterns. In each experiment, yield components (particle number, grain number, 100 grain mass) were measured separately for main shoots, basal tillers, and nodal tillers. Under optimum conditions, landraces had a significantly lower grain yield than the cultivars, but no significant differences were observed at yield levels around 1 ton ha(-1). This genotype x environment interaction for grain yield was due to a difference in yield strategy, where landraces aimed at minimising the risk of a crop failure under stress conditions, and modem cultivars aimed at maximising yield potential under optimum conditions. A key aspect of the adaptation of landraces was the small size of the main shoot panicle, as it minimised (1) the loss of productive tillers during stem elongation; (2) the delay in anthesis if mid-season drought occurs; and (3) the reduction in panicle productivity of the basal tillers under stress. In addition, a low investment in structural panicle weight, relative to vegetative crop growth rate, promoted the production of nodal tillers, providing a mechanism to compensate for reduced basal tiller productivity if stress occurred around anthesis. A low maximum 100 grain mass also ensured individual grain mass was little affected by environmental conditions. The strategy of the high-tillering landraces carries a yield penalty under optimum conditions, but is expected to minimise the risk of a crop failure, particularly if mid-season drought stress occurs. The yield architecture of low-tillering varieties, by contrast, will be suited to end-of-season drought stress, provided anthesis is early. Application of the above adaptation mechanisms into a breeding program could enable the identification of plant types that match the prevalent stress patterns in the target environments. (C) 2003 E.J. van Oosterom. Published by Elsevier Science B.V. All rights reserved.

Variabilidade espacial do estado nutricional do cafeeiro conilon utilizando índice DRIS

A combinação da agricultura de precisão e do Sistema Integrado de Recomendação Foliar (DRIS) possibilita monitorar espacialmente o balanço nutricional dos cafezais para fornecer recomendações de adubação mais equilibradas e mais ajustadas economicamente. O objetivo deste trabalho foi avaliar a variabilidade espacial do estado nutricional do cafeeiro conilon, utilizando o Índice de Balanço Nutricional (IBN) e sua relação com a produtividade. A produtividade das plantas em cada ponto amostral foi determinada e construiu-se o seu mapa considerando a variabilidade espacial; determinou-se o Índice de Equilíbrio Nutricional (IBN) das plantas em cada ponto amostral e construiu-se o seu mapa; e utilizou-se a análise de componentes principais (ACP) para estimar o IBN do cafeeiro por cokrigagem. Os dados do cafeeiro conilon foram coletados em fazenda experimental, no município de Cachoeiro de Itapemirim-ES. O IBN do cafeeiro e a sua produtividade foram analisados por meio de geoestatística, com base nos modelos e parâmetros dos semivariogramas, utilizando o método de interpolação krigagem ordinária para estimar valores para locais não amostrados. O índice de Balanço Nutricional da lavoura do cafeeiro conilon apresentou dependência espacial, porém não apresentou correlação linear e nem espacial com a produtividade. A lavoura em estudo se encontra em desequilíbrio nutricional, sendo que entre os macronutrientes, o Potássio foi o que apresentou maior desequilíbrio na área, entre os micronutrientes, o Zinco e o Ferro foram os que apresentaram menores concentrações nas folhas. A confecção dos mapas possibilitou a distinção de regiões com maior e menor desequilíbrio nutricional e produtividade, o que possibilita adotar o manejo de forma diferenciada e localizada. A análise multivariada baseada em componentes principais fornece componentes com alta correlação com as variáveis originais P, Ca, Zn , Cu, K e B. A cokrigagem utilizando as componentes principais permite estimar o IBN e a produtividade da área.

Gender wage and productivity differentials in the Portuguese tourism industry

The objective of this paper is to provide empirical evidence on the determinants of gender wage inequality in the Portuguese tourism industry. Relying on firm level wage equations and production functions, gender wage and productivity differentials are estimated and then compared in order to infer whether observed gender disparities are justifiable on the grounds that women are relatively less productive than men, or instead disparities are due to gender wage discrimination. This approach is applied to tourism industry data gathered in the matched employer-employee data set Quadros de Pessoal (Employee Records). The main findings indicate that female employees in the tourism industry in Portugal are less productive than their male colleagues and that gender differences in wages are fully explained by gender differences in productivity.

Gender, wages, and productivity: an analysis of the tourism industry in northern Portugal

Tourism represents a major economic activity in Portugal, with an enormous wealth and employment growth potential. A significant proportion of jobs in the industry tourism are occupied by women, given that this industry is characterized by a relatively higher percentage of female employees. Despite the evidence of female progress with regard to their role in the Portuguese labor market, women continue to earn less than their male counterparts. This is clearly the case of the tourism industry, where statistics reveal a persistent gender wage gap. The objective of this paper is to provide empirical evidence on the determinants of gender wage inequality in the tourism industry in northern Portugal. Relying on firm-level wage equations and production functions, gender wage and productivity differentials are estimated and then compared. The comparison of these differentials allows inferring whether observed wage disparities are attributable to relatively lower female productivity, or instead disparities are due to gender wage discrimination. This approach is applied to tourism industry data gathered in the matched employer-employee data set Quadros de Pessoal (Employee Records). The main findings indicate that female employees in the tourism industry in northern Portugal are less productive than their male colleagues and that gender differences in wages are fully explained by gender differences in productivity.

Response of rice cultivars to nitrogen in upland conditions

Against the background of a growing world population, rice (Oryza sativa L.) consumption is expected to grow faster than its production. Therefore, an appropriate question would be: how to increase productivity in the short-term? In this respect, it becomes important the implementation of modern agricultural production systems, such as upland rice with supplemental sprinkler irrigation. Additional information is needed to maximize the available resources, with special attention given to research on the use of nitrogen. This study aimed to evaluate the agronomic performance of commercial rice cultivars with different plant characteristics in upland conditions with supplemental sprinkler irrigation, when subjected to nitrogen in topdress application at the R1 stage (panicle differentiation). The experiment was arranged in a randomized block with split plot design, with 65 treatments, consisting of the combination of 13 cultivars in the plots, and five nitrogen levels in the subplots (0, 40, 80, 120 and 160 kg ha-1), with four replications. Genetic variability was detected among rice cultivars and the agronomic performance in response to the applied nitrogen. The topdressing application of nitrogen increases, in general, the production components and grain yield in rice. Cultivars BRS Primavera, Caiapó and IAC 202 stood out for grain yield, followed by Baldo, Carnaroli, BRS Curinga and IAC 500 with lower yields.

Agronomic performance of 27 cocoa progenies and plant selection based on productivity, self-compatibility and disease resistance

The objective of the present work was to evaluate 27 progenies of cocoa crosses considering the agronomic traits and select F1 plants within superior crosses. The experiment was installed in March 2005, in the Experimental Station Joaquim Bahiana (ESJOB), in Itajuipe, Bahia. The area of the experiment is of approximately 3 ha, with a total of 3240 plants. Thirteen evaluations of vegetative brooms, five of cushion brooms and 15 of number of pods per plant were accomplished. Thirty pollinations were made for each selected plant to test for self-compatibility. The production, based on the number of pods per plant, and resistance to witches´ broom indicated CEPEC 94 x CCN 10, RB 39 x CCN 51 and CCN 10 x VB 1151 as superior progenies. All selections tested were self-compatible. The analyses of progenies and individual tree data, associated to visual field observations, allowed the selection of 17 plants which were included in a network of regional tests to determine the phenotypic stability.