Análise microestrutural de tubos API P110, para prospecção de petróleo e gás, soldados pelo processo HF/ERW

On the grounds of the great advances achieved over recent years, the process HF/ERW (High-Frequency/Electric Resistance Welding)welded pipe have played an active role in the oil and gas industry for deep water applications, at high and extremely low temperatures, under high pressure and in highly corrosive environments, gradually replacing manufactured pipes by other processes. However, studies have shown that defects in the welded joints are a the leading causes of pipelines failures, which has required the determination of toughness values in this region, in compliance with the strict recommendations of the codes and standards with manufacturers and construction companies, on the oil and gas sector. As part of the validation process required toughness values, this research project focuses on a microstructural analysis in HF / ERW tubes microalloyed, steel grade API 5CT P110, designed to explore oil and gas in deep waters, the subject of strategic relevance to the country because of the recent discoveries in the Santos mega fields: Tupi and Libra (pre-salt). In this scientific work will be presented and discussed the results of mechanical tensile and Charpy, a few CTOD tests curves (showing the trend of toughness values to be obtained), and the microstructures of the base material obtained by optical microscopy, with special emphasis on the formation of nonmetallic inclusions in the welded joint

Estudo do comportamento em fadiga de uma chapa de aço microligado, grau API 5L X70

In engineering, for correct designing the structural components required for cyclical stresses, it is necessary to determine a limit of resistance to fatigue, which is the maximum amplitude of the applied tension under which the fatigue failure does not occurs after a certain number cycles. The marine environment is hostile, not only by the high pressure, corrosion, but also by low temperatures. Petrol Production units, composed of the risers (pipelines connecting the oil well to the ship), are dimensioned to remain installed for periods of 20 up to 30 years, and must therefore be prepared to support various efforts, such as tidal, wind currents and everything that is related. This paper focuses on a study on the fatigue behavior of microalloyed steel, API 5L Grade X70, used to transport oil and gas by pipelines. For analysis, we obtained the curves S-N (stress vs. number of cycles) using laboratory data collected from cylindrical longitudinal and transverse specimens used in axial fatigue test in accordance with ASTM E466. The tensile tests and microhardness were performed to characterize the mechanical properties of the samples, and it was found that the values meet the specifications of the standard API 5L. To characterize microstructurally the material, it was also made a metallographic analysis of the steel under study, and the origin of the fatigue crack was investigated with the support of a scanning electron microscope (SEM).

Phenolic compounds, carotenoids, tocopherols and fatty acids present in oils extracted from palm fruits

This review aimed to discuss the main bioactive compounds present in oils extracted from palm trees, indicating possible applications for the same. The bioactive compounds approached were: phenolic compounds, carotenoids, tocopherols, mono and polyunsaturated fatty acids. It is growing the search for food, especially from plant origin, characterized by the presence of such substances due to their benefi ts. Many studies show palm species as important sources of bioactive compounds and essential fatty acids. Therefore it is important to study the fruit characterization and composition of the oil from palm species of different regions that are still poorly investigated, seeking the possibility of its application in industry or the development of functional foods.

Análise microestrutural de tubos API N80 soldados pelo processo HF/ERW para prospecção de petróleo e gás

On the grounds of the great advances achieved over recent years, the process HF/ERW (High-Frequency/Electric Resistance Welding)welded pipe have played an active role in the oil and gas industry for deep water applications, at high and extremely low temperatures, under high pressure and in highly corrosive environments, gradually replacing manufactured pipes by other processes. However, studies have shown that defects in the welded joints are a the leading causes of pipelines failures, which has required the determination of toughness values in this region, in compliance with the strict recommendations of the codes and standards with manufacturers and construction companies, on the oil and gas sector. As part of the validation process required toughness values, this research project focuses on a microstructural analysis in HF / ERW tubes microalloyed, steel grade API 5CT N80, designed to explore oil and gas in deep waters, the subject of strategic relevance to the country because of the recent discoveries in the Santos mega fields: Tupi and Libra (pre-salt). In this scientific work will be presented and discussed the results of mechanical tensile and Charpy, a few CTOD tests curves (showing the trend of toughness values to be obtained), and the microstructures of the base material obtained by optical microscopy, with special emphasis on the formation of non-metallic inclusions in the welded joint

Atividade antioxidante e determinação de fenóis totais, carotenoides, betacarotenos, licopeno e zinco em variedades branca, amarela e rosada de Manihot Esculenta Crantz

There are cassava varieties that present compounds as carotenoids, beta-carotene, lycopene and minerals important for human and animal health. The present study evaluated the antioxidant activity of the white, yellow and pinkish varieties of Manihot esculenta, by mean of the DPPH test and by the ferrous ion-chelating activity. Furthermore, the total phenols, carotenoids, beta-carotene, lycopene and zinc contents were also determined. Utilizing the DPPH test it was possible to find that extracts of boiled samples presented higher antioxidant activity (89.53% - pinkish) in comparison to the fresh samples (1.97% - white). For the ferrous ion-chelating test, the highest activity was found for the boiled pinkish variety extract (63.43%) and the lowest was for fresh yellow extract (17.34%) the white sample did not present activity. The highest concentration of total phenols and zinc content was obtained for the boiled pinkish variety extract 136.12 mg EAG/g of extract and 0,811ppm, respectively, in the concentration of 1000 µg/mL. The pinkish variety presented also higher quantity of pigments, including carotenoid (29.40 µg/g), beta-carotene (9.14 µg/100g) and lycopene (68.92%). According to the results obtained in this study it was possible to conclude that the yellow and pinkish varieties of M. esculenta present quantity of phenolic compounds and minerals sufficient to attribute the antioxidant activity and may thus contribute to reduce oxidative damage and be used as nutraceuticals or directly ingested in the diet to maintain good health.

Estudo das alterações das propriedades mecânicas em aço A-516 grau 70 soldado e submetido a tratamento térmico de alívio de tensões

Pressure vessels are equipments that require a great care because of their high cost and human life risk in case of fail, and its fabrication methods are different for each manufacturer. Normally, pressure vessels and its parts are fabricated by welding, which may change local properties of metals. The head of a pressure vessel is a very important structural component and it is fabricated by welding and mechanical conformation. Because its excellent mechanical properties, de steel A-516 Grade 70 is often used in manufacturing of large pressure vessels that are subjected to high pressure and temperature, but was verified that its mechanical resistance is decreased when submitted to a tension relief heat treatment. By experience it was defined that before mechanical conformation of the head of a large pressure vessel, the steel should be submitted to a stress relief heat treatment in order to facilitate the mechanical conformation, but there is no quantitative analysis to prove this method and study its possible risks. In the present work the steel A-516 Grade 70 demonstrated a decrease of its mechanical resistance when submitted to a stress relief heat treatment, but keeping above the minimum limit defined in the literature. By other side its ductility was substantially increased, being possible to deduce that the stress relief heat treatment before mechanical conformation is a viable e recommended technique, but with reservations. With the data acquired during the fabrication e preparation of the specimen and the result of the tests, it was possible to elaborate a welding procedure that provides the same results obtained in this present work

Estudo do comportamento em fadiga de um tubo de aço microligado, grau API 5L X70

This work focuses on a study on the fatigue behavior of a microalloyed steel API 5L X70, used in pipes lines to transport oil and gas. These types of steels have excellent mechanical resistance values and ductility and therefore increased their study driven by increased demand for oil and especially natural gas, which consequently raises the need to build new pipelines to transport these products. The oil extraction units, composed of the risers (pipelines connecting the oil well to the ship), are dimensioned to remain installed for periods of 20 to 30 years in the marine environment, a hostile environment for high pressure, corrosion, low temperatures and the stresses caused by the movement of water and tides. For analysis, the S-N (stress versus number of cycles) curves were obtained from data collected from bodies-of-proof cylindrical longitudinal, transverse and that one removed from the weld area of the pipe, tested in accordance with ASTM E466. Tensile tests were performed for characterizing the mechanical properties of the samples and welded joints, concluded that the values meet the specifications of the standard API 5L. To characterize microstructural material, also metallographic analysis was made of regions of the base metal and the HAZ. The results of fatigue tests demonstrated a higher life for the specimens removed from the longitudinal direction the pipe, followed by those in the transverse direction and, finally, the welded joint. The origins of the fatigue cracks were determined by scanning electron microscopy (SEM)

Produção de bebida mista de extrato hidrossolúvel de soja e suco de uva submetida a diferentes doses de radiação gama

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Indústria frigorífica halal no Brasil, mão-de-obra islamita e estado de exceção

In the last decade, Brazilian meat export rates for Muslim religious countries have increased, and also has the immigration of Africans workers able to perform the slaughter following the precepts of Islam - religion that has expanded in the world, and thus, has the halal food segment. Halal, the Islamic ideology, means lawful, authorized by God: are those products that Allah in the Holy Qur'an releases for human consumption. To get halal certification some measures during slaughter/processing food should be taken. In the case of the slaughterhouses the animal must be slaughtered by a Muslim. Consequently, the demand for this skilled labor makes many African-Muslims get jobs in factories owned by BRF Foods, JBS and Marfrig; refugees and with their citizenship rights committed, these individuals live in a socio-political state of exception and overexploitation. In this study we intend to discuss the object of study Islamist workforce in Brazilian halal meat industry using the theoretical reflections of Giorgio Agamben (Homo Sacer in 2002, and State of Exception, 2004) and David Harvey (The Condition of Postmodernity, 2008, and The New Imperialism, 2004) to address the situation of immigrants in the meat business in Brazil, specially those on the halal certification segment, whose working and living conditions were described from academic studies and primary sources (articles in newspapers / magazines, websites, immigration official data). In addition we use the works of Rogério Heasbaert (O mito da desterritorialização, 2007) and Robert Kurz (Os paradoxos dos direitos humanos: inclusão e exclusão na modernidade, 2003) to discuss human mobility in this new century

Efeito das diferentes direções de aplicação de jato de fluido de corte no torneamento de um aço de difícil usinagem

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Isotope analysis method (δ¹³C) in clarified apple juice

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Método simples para quantificar o metabolismo aeróbio e aneróbio de levedura alcoólica

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Células-combustível a etanol direto embarcadas em aeronaves: estudo de utilização e recuperação de calor residual

Pós-graduação em Engenharia Mecânica - FEG

CHARACTERIZATION STUDY OF CAMBUCI FRUIT [Campomanesia phaea (O. Berg.) Landrum] AND ITS APPLICATION IN JELLY PROCESSING

CHARACTERIZATION STUDY OF CAMBUCI FRUIT [Campomanesia phaea (O. Berg.) Landrum] AND ITS APPLICATION IN JELLY PROCESSING The objective of this paper was to study possible differences of varieties of cambuci fruit reported by producers by means of fruit characterization and elaboration of jelly. The fruits were divided in four possible varieties groups, named as A, B, C and D, and submitted to analysis regarding weight, ash, moisture, pH, soluble solids, acidity, ratio, ascorbic acid and water activity. To the preparation of the jelly was chosen the variety A with two formulations, 50%50% and 40%60%, fruit and sugar respectively. Concerning the possible varieties of cambuci only water activity was not significantly different. The acidity and ratio of B variety are noteworthy, because it did differ from the others presenting a more satisfactory result for in natura consumption. All other tests presented statistic alteration of at least one variety, but since these data can be influenced by edaphoclimatic conditions they must be carefully observed. Lower results for pH, acidity, luminosity and degrees hue, were observed for the 60% sugar jelly sample, which contributed for its better results in the preference test for the attributes appearance, color, flavor and texture. The evaluation of attribute aroma of both samples (50% and 60%) did not differ.

Incrustação em poço produtor de petróleo e gás natural: um estudo de caso

Water and gas is a common by - product of the oil production process. Production may be compromised by the precipitation of inorganic salts in both the reservoir and producing well, through scale formation. This precipitation is likely the cause of the formation damage. High temperatures and h igh pressures (HTHP) may favor the precipitation of insoluble salts. The most common types of scale in oil fields are calcium carbonate and calcium sulphate, strontium and barium sulphate. New types of scale formation have attracted special attention such as zinc sulphide and lead. This precipitation may occur in the pores of reservoir rocks, in the production string and in equipment, causing obstructions and consequent production losses. In this study, the influence of well depth on incrustation compositio n was investigated to design removal treatments and assess the behavior of these deposits along the string, through the analysis of pressure and temperature. Scale residues were recovered from the inside of the production string of an oil and gas well duri ng the string removal operation. A total of 10 samples from different depths (15.4 m to 4061.5 m) were obtained. Initially a dissolution test was conducted in weak acid, similar to that used in removal operations with this type of scale formation. Majority composition was defined and confirmed by dissolution tests using X - Ray Fluorescence Spectroscopy (XRF), X - Ray Diffraction (XRD) and Scanning Electron Microscope (SEM) techniques. Residues with distinct characteristics were observed in different proportion s, showing a tendency toward increased and/or decreased mass with depth. In the samples closest to the surface, typical sandstone residues were found, with calcium (45% Ca) as the metal of highest concentration. The obtained results indicate correlations o f the scale types studied with the depth and, consequently, with the thermodynamic conditions of pressure and temperature.