Development of EDMI Calibration Baseline, HR-241, 1984

Electronic distance measuring instruments (EDMI) are used by surveyors in routine length measurements. The constant and scale factors of the instrument tend to change due to usage, transportation, and aging of crystals. Calibration baselines are established to enable surveyors to check the instruments and determine any changes in the values of constant and scale factors. The National Geodetic Survey (NGS) has developed guidelines for establishing these baselines. In 1981 an EDMI baseline at ISU was established according to NGS guidelines. In October 1982, the NGS measured the distances between monuments. Computer programs for reducing observed distances were developed. Mathematical model and computer programs for determining constant and scale factors were developed. A method was developed to detect any movements of the monuments. Periodic measurements of the baseline were made. No significant movement of the monuments was detected.

Determination of Tension Crack Development in Plastic P.C. Concrete with Retarding Admixtures, MLR-86-12, 1987

Bridge deck cracking occasionally occurs during construction for any number of reasons. Improper design, concrete placement or deck curing can result in cracks. One contributing factor toward cracking may be dead load deflections induced during concrete placement. For both continuous and non-continuous bridges, specific placement sequences are required to minimize harmful deflections in previously placed sections. Set retarding admixtures are also used to keep previously placed concrete plastic until the pour is completed. The problem is--at what point does movement of the concrete cause permanent damage to the deck. The study evaluated the time to crack formation relationship for mixes with low and high dosages of set retarding admixtures currently approved for use in Iowa state and county projects.

Elastic stresses and plastic deformations in 'Santa Clara' tomato fruits caused by package dependent compression

The objective of this work was to study the fruit compression behavior aiming to develop new tomato packages. Deformations caused by compression forces were observed inside packages and in individual 'Santa Clara' tomato fruit. The forces applied by a transparent acrylic lever to the fruit surface caused pericarp deformation and the flattened area was proportional to the force magnitude. The deformation was associated to the reduction in the gas volume (Vg), caused by expulsion of the air from the loculus cavity and reduction in the intercellular air volume of the pericarp. As ripening advanced, smaller fractions of the Vg reduced by the compressive force were restored after the stress was relieved. The lack of complete Vg restoration was an indication of permanent plastic deformations of the stressed cells. Vg regeneration (elastic recovery) was larger in green fruits than in the red ones. The ratio between the applied force and the flattened area (flattening pressure), which depends on cell turgidity, decreased during ripening. Fruit movements associated with its depth in the container were observed during storage in a transparent glass container (495 x 355 x 220 mm). The downward movement of the fruits was larger in the top layers because these movements seem to be driven by a summation of the deformation of many fruits in all layers.

Plastic modifications within inhibitory control networks induced by practicing a stop-signal task: an electrical neuroimaging study.

INTRODUCTION: Inhibitory control refers to our ability to suppress ongoing motor, affective or cognitive processes and mostly depends on a fronto-basal brain network. Inhibitory control deficits participate in the emergence of several prominent psychiatric conditions, including attention deficit/hyperactivity disorder or addiction. The rehabilitation of these pathologies might therefore benefit from training-based behavioral interventions aiming at improving inhibitory control proficiency and normalizing the underlying neurophysiological mechanisms. The development of an efficient inhibitory control training regimen first requires determining the effects of practicing inhibition tasks. METHODS: We addressed this question by contrasting behavioral performance and electrical neuroimaging analyses of event-related potentials (ERPs) recorded from humans at the beginning versus the end of 1 h of practice on a stop-signal task (SST) involving the withholding of responses when a stop signal was presented during a speeded auditory discrimination task. RESULTS: Practicing a short SST improved behavioral performance. Electrophysiologically, ERPs differed topographically at 200 msec post-stimulus onset, indicative of the engagement of distinct brain network with learning. Source estimations localized this effect within the inferior frontal gyrus, the pre-supplementary motor area and the basal ganglia. CONCLUSION: Our collective results indicate that behavioral and brain responses during an inhibitory control task are subject to fast plastic changes and provide evidence that high-order fronto-basal executive networks can be modified by practicing a SST.

Internal arsenite bioassay calibration using multiple reporter cell lines

Bioassays with bioreporter bacteria are usually calibrated with analyte solutions of known concentrations that are analysed along with the samples of interest. This is done as bioreporter output (the intensity of light, fluorescence or colour) does not only depend on the target concentration, but also on the incubation time and physiological activity of the cells in the assay. Comparing the bioreporter output with standardized colour tables in the field seems rather difficult and error-prone. A new approach to control assay variations and improve application ease could be an internal calibration based on the use of multiple bioreporter cell lines with drastically different reporter protein outputs at a given analyte concentration. To test this concept, different Escherichia coli-based bioreporter strains expressing either cytochrome c peroxidase (CCP, or CCP mutants) or β-galactosidase upon induction with arsenite were constructed. The reporter strains differed either in the catalytic activity of the reporter protein (for CCP) or in the rates of reporter protein synthesis (for β-galactosidase), which, indeed, resulted in output signals with different intensities at the same arsenite concentration. Hence, it was possible to use combinations of these cell lines to define arsenite concentration ranges at which none, one or more cell lines gave qualitative (yes/no) visible signals that were relatively independent of incubation time or bioreporter activity. The discriminated concentration ranges would fit very well with the current permissive (e.g. World Health Organization) levels of arsenite in drinking water (10 µg l−1).

Calibration of Highway Safety Manual Work Zone Crash Modification Factors, TPF-5(081), 2014

The Highway Safety Manual is the national safety manual that provides quantitative methods for analyzing highway safety. The HSM presents crash modification factors related to work zone characteristics such as work zone duration and length. These crash modification factors were based on high-impact work zones in California. Therefore there was a need to use work zone and safety data from the Midwest to calibrate these crash modification factors for use in the Midwest. Almost 11,000 Missouri freeway work zones were analyzed to derive a representative and stratified sample of 162 work zones. The 162 work zones was more than four times the number of work zones used in the HSM. This dataset was used for modeling and testing crash modification factors applicable to the Midwest. The dataset contained work zones ranging from 0.76 mile to 9.24 miles and with durations from 16 days to 590 days. A combined fatal/injury/non-injury model produced a R2 fit of 0.9079 and a prediction slope of 0.963. The resulting crash modification factors of 1.01 for duration and 0.58 for length were smaller than the values in the HSM. Two practical application examples illustrate the use of the crash modification factors for comparing alternate work zone setups.

Investigation of Plastic Pipes for Highway Applications, HR-373A, Phase II, 1997

It is generally accepted that high density polyethylene pipe (HDPE) performs well under live loads with shallow cover, provided the backfill is well compacted. Although industry standards require carefully compacted backfill, poor inspection and/or faulty construction may result in soils that provide inadequate restraint at the springlines of the pipes thereby causing failure. The objectives of this study were: 1) to experimentally define a lower limit of compaction under which the pipes perform satisfactorily, 2) to quantify the increase in soil support as compaction effort increases, 3) to evaluate pipe response for loads applied near the ends of the buried pipes, 4) to determine minimum depths of cover for a variety of pipes and soil conditions by analytically expanding the experimental results through the use of the finite element program CANDE. The test procedures used here are conservative especially for low-density fills loaded to high contact stresses. The failures observed in these tests were the combined effect of soil bearing capacity at the soil surface and localized wall bending of the pipes. Under a pavement system, the pipes' performance would be expected to be considerably better. With those caveats, the following conclusions are drawn from this study. Glacial till compacted to 50% and 80% provides insufficient support; pipe failureoccurs at surface contact stresses lower than those induced by highway trucks. On the other hand, sand backfill compacted to more than 110 pcf (17.3 kN/m3) is satisfactory. The failure mode for all pipes with all backfills is localized wall bending. At moderate tire pressures, i.e. contact stresses, deflections are reduced significantly when backfill density is increased from about 50 pcf (7.9 kN/m^3) to 90 pcf (14.1 kN/m^3). Above that unit weight, little improvement in the soil-pipe system is observed. Although pipe stiffness may vary as much as 16%, analyses show that backfill density is more important than pipe stiffness in controlling both deflections at low pipe stresses and at the ultimate capacity of the soil-pipe system. The rate of increase in ultimate strength of the system increases nearly linearly with increasing backfill density. When loads equivalent to moderate tire pressures are applied near the ends of the pipes, pipe deflections are slighly higher than when loaded at the center. Except for low density glacial till, the deflections near the ends are not excessive and the pipes perform satisfactorily. For contact stresses near the upper limit of truck tire pressures and when loaded near the end, pipes fail with localized wall bending. For flowable fill backfill, the ultimate capacity of the pipes is nearly doubled and at the upper limit of highway truck tire pressures, deflections are negligible. All pipe specimens tested at ambient laboratory room temperatures satisfied AASHTO minimum pipe stiffness requirements at 5% deflection. However, nearly all specimens tested at elevated pipe surface temperatures, approximately 122°F (50°C), failed to meet these requirements. Some HDPE pipe installations may not meet AASHTO minimum pipe stiffness requirements when installed in the summer months (i.e. if pipe surface temperatures are allowed to attain temperatures similar to those tested here). Heating of any portion of the pipe circumference reduced the load carrying capacity of specimens. The minimum soil cover depths, determined from the CANOE analysis, are controlled by the 5% deflection criterion. The minimum soil cover height is 12 in. (305 mm). Pipes with the poor silt and clay backfills with less than 85% compaction require a minimum soil cover height of 24 in. (610 mm). For the sand at 80% compaction, the A36 HDPE pipe with the lowest moment of inertia requires a minimum of 24 in. (610 mm) soil cover. The C48 HDPE pipe with the largest moment of inertia and all other pipes require a 12 in. (305 mm) minimum soil cover.

Calibration and Reliability of a Nuclear Asphalt Content Gauge, MLR-87-02, 1987

Based on results of an evaluation performed during the winter of 1985-86, six Troxler 3241-B Asphalt Content Gauges were purchased for District use in monitoring project asphalt contents. Use of these gauges will help reduce the need for chemical based extractions. Effective use of the gauges depends on the accurate preparation and transfer of project mix calibrations from the Central Lab to the Districts. The objective of this project was to evaluate the precision and accuracy of a gauge in determining asphalt contents and to develop a mix calibration transfer procedure for implementation during the 1987 construction. The first part of the study was accomplished by preparing mix calibrations in the Central Lab gauge and taking multiple measurements of a sample with known asphalt content. The second part was accomplished by preparing transfer pans, obtaining count data on the pans using each gauge, and transferring calibrations from one gauge to another through the use of calibration transfer equations. The transferred calibrations were tested by measuring samples with a known asphalt content. The study established that the Troxler 3241-B Asphalt Content Gauge yields results of acceptable accuracy and precision as evidenced by a standard deviation of 0.04% asphalt content on multiple measurements of the same sample. The calibration transfer procedure proved feasible and resulted in the calibration transfer portion of Materials I.M. 335 - Method of Test For Determining the Asphalt Content of Bituminous Mixtures by the Nuclear Method.

Plastic Air Content versus Hardened Air Content by High Pressure Air Meter, MLR-99-03, 2001

Plastic air content is typically tested by the pressure method, ASTM C138. Loss of air content through the paver has been shown to exceed 2 percent at times. Research has shown that early deterioration of pavements in Iowa may be directly or indirectly related to low or inadequate air content. Hardened air content is typically checked using the linear traverse method, ASTM C457. The linear traverse method is very time consuming and could not be used on a production scale. A quick and effective method of testing in place air content is needed. Research has shown a high degree of correlation with the high-pressure method of determining air content of hardened concrete versus plastic air content in laboratory conditions. This research indicated that air contents are more variable when comparing core results to plastic air content, although the overall average for the air content was comparable. Perhaps, the location of the plastic air content test, obtained from construction records, versus location of the cores was not as accurate as needed.

Examination of Curing Criteria for Cold In-Place Recycling (Phase 3: Calibration of Moisture Loss Indices and Development of Stiffness Gain Model), TR-609, 2011

In the previous study, moisture loss indices were developed based on the field measurements from one CIR-foam and one CIR-emulsion construction sites. To calibrate these moisture loss indices, additional CIR construction sites were monitored using embedded moisture and temperature sensors. In addition, to determine the optimum timing of an HMA overlay on the CIR layer, the potential of using the stiffness of CIR layer measured by geo-gauge instead of the moisture measurement by a nuclear gauge was explored. Based on the monitoring the moisture and stiffness from seven CIR project sites, the following conclusions are derived: 1. In some cases, the in-situ stiffness remained constant and, in other cases, despite some rainfalls, stiffness of the CIR layers steadily increased during the curing time. 2. The stiffness measured by geo-gauge was affected by a significant amount of rainfall. 3. The moisture indices developed for CIR sites can be used for predicting moisture level in a typical CIR project. The initial moisture content and temperature were the most significant factors in predicting the future moisture content in the CIR layer. 4. The stiffness of a CIR layer is an extremely useful tool for contractors to use for timing their HMA overlay. To determine the optimal timing of an HMA overlay, it is recommended that the moisture loss index should be used in conjunction with the stiffness of the CIR layer.

Yield potential of chive : effects of cultivar, plastic mulch and fertilisation

Selostus: Lajikkeen, muovikatteen ja lannoituksen vaikutus ruohosipulin satoon

Modélisation par automate cellulaire des phénomènes diagénétiques des plateformes carbonatées : calibration et paramétrage à partir de deux cas d'études : l'Urgonien du Vercors (Crétacé inférieur, SE France) et les Calcaires Gris du Mont Compomolon (Lias, NE Italie)

Une fois déposé, un sédiment est affecté au cours de son enfouissement par un ensemble de processus, regroupé sous le terme diagenèse, le transformant parfois légèrement ou bien suffisamment pour le rendre méconnaissable. Ces modifications ont des conséquences sur les propriétés pétrophysiques qui peuvent être positives ou négatives, c'est-à-dire les améliorer ou bien les détériorer. Une voie alternative de représentation numérique des processus, affranchie de l'utilisation des réactions physico-chimiques, a été adoptée et développée en mimant le déplacement du ou des fluides diagénétiques. Cette méthode s'appuie sur le principe d'un automate cellulaire et permet de simplifier les phénomènes sans sacrifier le résultat et permet de représenter les phénomènes diagénétiques à une échelle fine. Les paramètres sont essentiellement numériques ou mathématiques et nécessitent d'être mieux compris et renseignés à partir de données réelles issues d'études d'affleurements et du travail analytique effectué. La représentation des phénomènes de dolomitisation de faible profondeur suivie d'une phase de dédolomitisation a été dans un premier temps effectuée. Le secteur concerne une portion de la série carbonatée de l'Urgonien (Barrémien-Aptien), localisée dans le massif du Vercors en France. Ce travail a été réalisé à l'échelle de la section afin de reproduire les géométries complexes associées aux phénomènes diagénétiques et de respecter les proportions mesurées en dolomite. De plus, la dolomitisation a été simulée selon trois modèles d'écoulement. En effet, la dédolomitisation étant omniprésente, plusieurs hypothèses sur le mécanisme de dolomitisation ont été énoncées et testées. Plusieurs phases de dolomitisation per ascensum ont été également simulées sur des séries du Lias appartenant aux formations du groupe des Calcaire Gris, localisées au nord-est de l'Italie. Ces fluides diagénétiques empruntent le réseau de fracturation comme vecteur et affectent préférentiellement les lithologies les plus micritisées. Cette étude a permis de mettre en évidence la propagation des phénomènes à l'échelle de l'affleurement. - Once deposited, sediment is affected by diagenetic processes during their burial history. These diagenetic processes are able to affect the petrophysical properties of the sedimentary rocks and also improve as such their reservoir capacity. The modelling of diagenetic processes in carbonate reservoirs is still a challenge as far as neither stochastic nor physicochemical simulations can correctly reproduce the complexity of features and the reservoir heterogeneity generated by these processes. An alternative way to reach this objective deals with process-like methods, which simplify the algorithms while preserving all geological concepts in the modelling process. The aim of the methodology is to conceive a consistent and realistic 3D model of diagenetic overprints on initial facies resulting in petrophysical properties at a reservoir scale. The principle of the method used here is related to a lattice gas automata used to mimic diagenetic fluid flows and to reproduce the diagenetic effects through the evolution of mineralogical composition and petrophysical properties. This method developed in a research group is well adapted to handle dolomite reservoirs through the propagation of dolomitising fluids and has been applied on two case studies. The first study concerns a mid-Cretaceous rudist and granular platform of carbonate succession (Urgonian Fm., Les Gorges du Nan, Vercors, SE France), in which several main diagenetic stages have been identified. The modelling in 2D is focused on dolomitisation followed by a dédolomitisation stage. For the second study, data collected from outcrops on the Venetian platform (Lias, Mont Compomolon NE Italy), in which several diagenetic stages have been identified. The main one is related to per ascensum dolomitisation along fractures. In both examples, the evolution of the effects of the mimetic diagenetic fluid on mineralogical composition can be followed through space and numerical time and help to understand the heterogeneity in reservoir properties. Carbonates, dolomitisation, dédolomitisation, process-like modelling, lattice gas automata, random walk, memory effect.

Collaborative explicit plasticity framework: a conceptual scheme for the generation of plastic and group-aware user interfaces

The advent of new advances in mobile computing has changed the manner we do our daily work, even enabling us to perform collaborative activities. However, current groupware approaches do not offer an integrating and efficient solution that jointly tackles the flexibility and heterogeneity inherent to mobility as well as the awareness aspects intrinsic to collaborative environments. Issues related to the diversity of contexts of use are collected under the term plasticity. A great amount of tools have emerged offering a solution to some of these issues, although always focused on individual scenarios. We are working on reusing and specializing some already existing plasticity tools to the groupware design. The aim is to offer the benefits from plasticity and awareness jointly, trying to reach a real collaboration and a deeper understanding of multi-environment groupware scenarios. In particular, this paper presents a conceptual framework aimed at being a reference for the generation of plastic User Interfaces for collaborative environments in a systematic and comprehensive way. Starting from a previous conceptual framework for individual environments, inspired on the model-based approach, we introduce specific components and considerations related to groupware.