Desenvolvimento de um computador de bordo para veículo Baja-SAE

The objective of this paper is show the development of an Eletronic Control Unit (ECU) for Baja-SAE vehicles from its requirements to final implementation. An ECU for Baja-SAE vehicles is made of electric and electronic circuits (appropriated to the hostile situations of an off-road competition) able to make important measurements for the running or stand-by vehicle performance. For this development, some concepts were studied: embedded electronics concepts (mainly microcontrollers and data acquisition circuits) and sensoring. Both the studies were made considering the off-road environment. After these initial studies, the elaboration of the basics hardware and software (under simulations) has begun, and this elaboration objectives maximum performance and low implementation cost. After the theorical studies, basic definition of the hardware and software’s architectures and simulations, the printed circuit boards (PCB) were made, as exhaustive tests in these boards for debugging and verify if the boards work well. Once the system was tested in the university, it ran into a regional Southeast competition in 2010, that definitely proved the efficiency of the whole system

Analysis of a microbial community associated with polychlorinated biphenyl degradation in anaerobic batch reactors

The degradation of polychlorinated biphenyls (PCBs) was investigated under fermentativemethanogenic conditions for up to 60 days in the presence of anaerobic biomass from a full-scale UASB reactor. The low methane yields in the PCBs-spiked batch reactors suggested that the biomass had an inhibitory effect on the methanogenic community. Reactors containing PCBs and co-substrates (ethanol/ sodium formate) exhibited substantial PCB reductions from 0.7 to 0.2 mg mL-1 . For the Bacteria domain, the PCBs-spiked reactors were grouped with the PCB-free reactors with a similarity of 55 %, which suggested the selection of a specific population in the presence of PCBs. Three genera of bacteria were found exclusively in the PCB-spiked reactors and were identified using pyrosequencing analysis, Sedimentibacter, Tissierela and Fusibacter. Interestingly, the Sedimentibacter, which was previously correlated with the reductive dechlorination of PCBs, had the highest relative abundance in the RCS-PCB (7.4 %) and RCS-PCB-PF (12.4 %) reactors. Thus, the anaerobic sludge from the UASB reactor contains bacteria from the Firmicutes phylum that are capable of degrading PCBs.

Effect of staining agents on color change of composites

Composite resins are materials that can present color changing when exposed to pigments. Objective: The aim of this study was to evaluate, in vitro, the color changing of composites after immersion in different substances for different periods. Material and methods: Two microhybrid composite resins: Charisma (Heraeus – Kulzer) and Opallis (FGM) were used. Red wine and acai pulp were also used as immersion medium. For this study, 32 specimens with 10 mm of diameter and 2 mm of thickness were used, divided into 4 groups: Group 1 – Opallis composite immersed in red wine solution; Group 2 – Opallis composite immersed in acai berry pulp solution; Group 3 – Charisma composite immersed in red wine solution; Group 4 – Charisma composite immersed in acai berry pulp solution. The specimens were evaluated in the following time periods: T0 – baseline, T1 – 24 hours, T2 – 48 hours, T3 – 72 hours and T4 – 96 hours. For the assessment of staining, a spectrophotometer for colorimetry was used (Color Guide 45 / 0, PCB 6807 BYK-Gardner Gerestsried GmBH, Germany), and the values obtained were transferred to a computer and recorded according to CIELAB system. Results: The data were evaluated using Kruskal- Wallis non-parametric tests with the following mean values for the immersion periods of 24, 48, 72 and 96 hours, respectively: G1 – 7.35, 7.84, 9.04,10.48; G2 – 2.92, 4.15, 4.30, 4.64; G3 – 3.14, 7.35, 8.13, 8.43, G4 – 4.49, 5.99, 6.92, 6.76. Conclusion: Red wine showed a higher tendency toward altering the composite color than acai berry pulp. In addition, no significant difference was found concerning to the behavior of the two composite resins. Concerning to the immersion time periods, significant differences were only observed among the groups in the 24 hour time period.

O militante em cena: Gianfrancesco Guarnieri e Eles não usam black tie

Pós-graduação em Artes - IA

Poluentes orgânicos persistentes em ar interior: desenvolvimento de método de extração em adsorvente para amostragem ativa

Persistent Organic Pollutants (POPs) are chemical substances extraordinarily toxic and persistent in the environment. Due to these properties, POPs are targets of the Stockholm Convention which aims to provide means to eliminate production and use by encouraging the reduction and, where possible, eliminating the release of these contaminants to the environment. One of the articles of this _Convention aims to assess the basal levels of such substances in the environment to monitor both the reduction of release to the environment, and to assess human exposure, using analyzes of milk and air for example. Although efforts to control POPs production and release to the environment have been made, data about their levels in Brazil are still scarce, mainly in the atmosphere or indoor environment. Considering the permanence of people inside its house, this study presents a method for POP extraction from XAD-2 sorbent employed in indoor air sampling, with identification and quantification by GC-ECD. GC-ECD linear range of the studied analytes, congeners of polychlorinated biphenyls (PCB) (28, 52, 101, 118, 138, 153 and 180), DDTs and their metabolites (DDDs, DDEs) and endosullan (isomers c - and 13 - and metabolite endosulfan sulfate) ranged between 0.5 and 16.0 ng mL-I with r2 > 0.967. The method developing consist of selecting the extraction solvent system by agitation (90 rpm, 1 hour) with n-hexan,e (2 mL) or n-hexane:acetone (1:1, v/v) (2 mL), concentration the extract with a gentle N2 stream, and evaluation of breakthrough with passage or air through the fortified XAD-2 cartridge before extraction, employing a low volume air suction pump (Pump Model 224 universal-PCXR8; 5-5000 mL min-1, SKC Inc., Eighty Four, PA, USA), Calibrator Dry-Cal DC-Lite (BIOS, Butler, NJ, USA)). Two fortification levels were employed, 15 and 30 ng. After selecting n-hexane as extraction solvent, with accuracy and precision ranging...

El Machete e A Classe Operária: a imprensa comunista mexicana e brasileira (1920-1940)

Pós-graduação em História - FCLAS

Heitor Ferreira Lima e a industrialização do Brasil

Pós-graduação em Ciências Sociais - FFC

O vermelho que violenta a ordem: os comunistas sob o olhar da DOPS no Paraná

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Dalcídio Jurandir: um cronista de O Estado do Pará e de Diretrizes

O escritor Dalcídio Jurandir (1909-1979) teve uma longa e profícua produção literária, da qual resultou em dez romances de ambientação amazônica e um – Linha do Parque –de orientação comunista. Entretanto, seu contato com o universo letrado não se restringiu a sua criação ficcional, o escritor exerceu intensa atividade na imprensa de modo geral e na imprensa comunista de modo particular. Essa última, em razão de seu envolvimento com o Partido Comunista Brasileiro (PCB), o qual foi substancial para a fundamentação do pensamento dalcidiano, tanto no que se refere ao modo enxergar a realidade e o seu funcionamento, quanto ao direcionamento da sua criação artística. Dois importantes periódicos para os quais Dalcídio colaborou nas cidades em que residiu foram O Estado do Pará e Diretrizes, ambos de orientações políticas esquerdistas, embora não organicamente ligados ao PCB. Nesses dois periódicos, é possível termos contanto com outra face do romancista, que além de compor seus romances, aventurou-se pelo caminho das crônicas. Dessa forma, objetivamos, com este trabalho, fazer um estudo dessas crônicas, nos dois jornais, entre os anos de 1937 a 1944, a fim de divulgar esses textos cronísticos do escritor marajoara e de compreender como ele se comportou na criação de outro gênero literário.

O vermelho que violenta a ordem: os comunistas sob o olhar da DOPS no Paraná

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Influence of artificial accelerated ageing on the colour stability of paints used for ocular prosthesis iris painting

Objectives: To evaluate the colour stability of paints used for ocular prosthesis iris painting submitted for accelerated artificial ageing (AAA). Materials and methods: Forty specimens of acrylic resin for sclera (16 x 2 mm) were made and separated into eight groups (n = 10) according to the type of paint (gouache, GP; oil, OP; acrylic AP; and composite resin for characterisation, CR) and the colours used (blue/brown). After drying (72 h), a new layer of colourless acrylic resin was applied and the initial colour readout was performed (Spectrophotometer PCB 6807). New colour readouts were performed after AAA, and Delta E was calculated. Results: Statistical analysis (two-way ANOVA-Bonferroni, p < 0.05) demonstrated that the brown colour showed lower Delta E means in comparison with the blue colour, with statistically significant difference for AP only. Blue colour showed no statistically significant difference with regard to the type of paint used. Brown AP showed lower Delta E than the other groups, with significant difference for OP and GP. GP showed greater alteration in Delta E for the brown colour, being statistically similar only to OP. Conclusions: Only the AP group for brown pigment shows clinically acceptable values for colour stability after AAA.

Color stability of modern composites subjected to different periods of accelerated artificial aging

The aim of this study was to evaluate the color stability of composites subjected to different periods of accelerated artificial aging (AAA). A polytetrafluorethylene matrix (10 x 2 mm) was used to fabricate 24 test specimens of three different composites (n=8): Tetric Ceram (Ivoclar/Vivadent); Filtek P90 and Z250 (3M ESPE), shade A3. After light activation for 20 s (FlashLite 1401), polishing and initial color readout (Spectrophotometer PCB 687; BYK Gardner), the test specimens were subjected to AAA (C-UV; Comexim), in 8-h cycles: 4 h exposure to UV-B rays at 50°C and 4 h condensation at 50°C. At the end of each cycle, color readouts were taken and the test ended when the mean value of ΔE attained a level ≥3.30. Tetric Ceram presented alteration in ΔE equal to 3.33 in the first aging cycle. For Filtek P90 and Z250, two (ΔE=3.60) and four (ΔE=3.42) AAA cycles were necessary. After each cycle, there was a reduction of luminosity in all the samples (ΔL). It was concluded that a short period of AAA was sufficient to promote clinically unacceptable color alteration in composites, and that this alteration was material-dependent.

Models of the Distribution of Persistent Organic Pollutants in the Marine Environment

Persistent organic pollutants (POPs) is a group of chemicals that are toxic, undergo long-range transport and accumulate in biota. Due to their persistency the distribution and recirculation in the environment often continues for a long period of time. Thereby they appear virtually everywhere within the biosphere, and poses a toxic stress to living organisms. In this thesis, attempts are made to contribute to the understanding of factors that influence the distribution of POPs with focus on processes in the marine environment. The bioavailability and the spatial distribution are central topics for the environmental risk management of POPs. In order to study these topics, various field studies were undertaken. To determine the bioavailable fraction of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), polychlorinated naphthalenes (PCNs), and polychlorinated biphenyls (PCBs) the aqueous dissolved phase were sampled and analysed. In the same samples, we also measured how much of these POPs were associated with suspended particles. Different models, which predicted the phase distribution of these POPs, were then evaluated. It was found that important water characteristics, which influenced the solid-water phase distribution of POPs, were particulate organic matter (POM), particulate soot (PSC), and dissolved organic matter (DOM). The bioavailable dissolved POP-phase in the water was lower when these sorbing phases were present. Furthermore, sediments were sampled and the spatial distribution of the POPs was examined. The results showed that the concentration of PCDD/Fs, and PCNs were better described using PSC- than using POM-content of the sediment. In parallel with these field studies, we synthesized knowledge of the processes affecting the distribution of POPs in a multimedia mass balance model. This model predicted concentrations of PCDD/Fs throughout our study area, the Grenlandsfjords in Norway, within factors of ten. This makes the model capable to validate the effect of suitable remedial actions in order to decrease the exposure of these POPs to biota in the Grenlandsfjords which was the aim of the project. Also, to evaluate the influence of eutrophication on the marine occurrence PCB data from the US Musselwatch and Benthic Surveillance Programs are examined in this thesis. The dry weight based concentrations of PCB in bivalves were found to correlate positively to the organic matter content of nearby sediments, and organic matter based concentrations of PCB in sediments were negatively correlated to the organic matter content of the sediment.

An evaluation of the distributions of polychlorinated biphenyls and organic matter in coastal sediments

The objective of this thesis is to improve the understanding of what processes and mechanism affects the distribution of polychlorinated biphenyls (PCBs) and organic carbon in coastal sediments. Because of the strong association of hydrophobic organic contaminants (HOCs) such as PCBs with organic matter in the aquatic environment, these two entities are naturally linked. The coastal environment is the most complex and dynamic part of the ocean when it comes to both cycling of organic matter and HOCs. This environment is characterised by the largest fluxes and most diverse sources of both entities. A wide array of methods was used to study these processes throughout this thesis. In the field sites in the Stockholm archipelago of the Baltic proper, bottom sediments and settling particulate matter were retrieved using sediment coring devices and sediment traps from morphometrically and seismically well-characterized locations. In the laboratory, the samples have been analysed for PCBs, stable carbon isotope ratios, carbon-nitrogen atom ratios as well as standard sediment properties. From the fieldwork in the Stockholm Archipelago and the following laboratory work it was concluded that the inner Stockholm archipelago has a low (≈ 4%) trapping efficiency for freshwater-derived organic carbon. The corollary is a large potential for long-range waterborne transport of OC and OC-associated nutrients and hydrophobic organic pollutants from urban Stockholm to more pristine offshore Baltic Sea ecosystems. Theoretical work has been carried out using Geographical Information Systems (GIS) and statistical methods on a database of 4214 individual sediment samples, each with reported individual PCB congener concentrations. From this work it was concluded that the continental shelf sediments are key global inventories and ultimate sinks of PCBs. Depending on congener, 10-80% of the cumulative historical emissions to the environment are accounted for in continental shelf sediments. Further it was concluded that the many infamous and highly contaminated surface sediments of urban harbours and estuaries of contaminated rivers cannot be of importance as a secondary source to sustain the concentrations observed in remote sediments. Of the global shelf PCB inventory < 1% are in sediments near population centres while ≥ 90% is in remote areas (> 10 km from any dwellings). The remote sub-basin of the North Atlantic Ocean contains approximately half of the global shelf sediment inventory for most of the PCBs studied.

Caratterizzazione e stimolazione dei processi di declorurazione riduttiva dei policlorobifenili in sedimenti marini

I policlorobifenili (PCB) sono un gruppo di 209 congeneri di bifenili policlorurati altamente tossici e persistenti che, a causa della loro elevata lipofilia, tendono ad accumularsi in sedimenti anaerobici marini, tramite i quali possono entrare nella catena alimentare. I PCB possono essere degradati mediante processi di declorurazione riduttiva mediati da popolazioni microbiche anaerobiche in grado di utilizzarli fortuitamente come accettori finali della catena respiratoria. Il processo consiste quindi nella bioconversione di congeneri ad alto grado di clorurazione in PCB basso clorurati, meno tossici, meno bioaccumulabili e più facilmente biodegradabili in condizioni aerobiche. Nel presente elaborato è stata investigata la capacità di una popolazione microbica arricchita su congeneri coplanari di PCB da un sedimento contaminato del Canale Brentella (Prima Zona Industriale di Porto Marghera, laguna di Venezia), di declorurare miscele commerciali di PCB (Aroclor 1254) in condizioni geobiochimiche di laboratorio che riproducono quelle presenti in sito. Il processo è quindi stato studiato in microcosmi anaerobici slurry di sedimento sospeso nella stessa acqua del sito e monitorato con un approccio chimico e microbiologico integrato. Ai fini di caratterizzare e stimolare i microganismi responsabili del processo degradativo sono state utilizzate tecniche convenzionali basate sull’inibizione selettiva di diversi gruppi microbici. Dopo una fase di latenza di 7 settimane, la coltura microbica ha declorurato velocemente ed estesamente la miscela commerciale di PCB saggiata, bioconvertendo il 70% dei congeneri ad alto grado di clorurazione (da penta- a octa- clorurati) in PCB di- e tri-clorurati. Il processo ha esibito selettività nei confronti delle posizioni meta dei gruppi 2,3- e 2,3,4-clorofenile e para dei gruppi 3,4- e 3,4,5-clorofenile, secondo il modello di declorurazione H’. Il monitoraggio delle attività microbiche in presenza dei diversi inibitori saggiati ha permesso inoltre di concludere che i batteri metanogeni e i batteri solfato-riduttori non sono direttamente coinvolti nel processo degradativo, suggerendo invece che le specie decloruranti siano appartenenti o strettamente correlate al genere Dehalococcoides. Poiché lo studio è stato eseguito in condizioni geobiochimiche di laboratorio che mimano quelle presenti in sito, i risultati ottenuti indicano che la popolazione microbica dei sedimenti del canale Brentella, se opportunamente stimolata, è potenzialmente in grado di mediare in situ la declorurazione riduttiva dei PCB preesistenti nel sedimento, contribuendo alla natural attenuation dei sedimenti contaminati.