Guidelines for Removal of Traffic Control Devices in Rural Areas, TR-527, 2005

It is commonly regarded that the overuse of traffic control devices desensitizes drivers and leads to disrespect, especially for low-volume secondary roads with limited enforcement. The maintenance of traffic signs is also a tort liability concern, exacerbated by unnecessary signs. The Federal Highway Administration’s (FHWA) Manual on Uniform Traffic Control Devices (MUTCD) and the Institute of Transportation Engineer’s (ITE) Traffic Control Devices Handbook provide guidance for the implementation of STOP signs based on expected compliance with right-of-way rules, provision of through traffic flow, context (proximity to other controlled intersections), speed, sight distance, and crash history. The approach(es) to stop is left to engineering judgment and is usually dependent on traffic volume or functional class/continuity of system. Although presently being considered by the National Committee on Traffic Control Devices, traffic volume itself is not given as a criterion for implementation in the MUTCD. STOP signs have been installed at many locations for various reasons which no longer (or perhaps never) met engineering needs. If in fact the presence of STOP signs does not increase safety, removal should be considered. To date, however, no guidance exists for the removal of STOP signs at two-way stop-controlled intersections. The scope of this research is ultra-low-volume (< 150 daily entering vehicles) unpaved intersections in rural agricultural areas of Iowa, where each of the 99 counties may have as many as 300 or more STOP sign pairs. Overall safety performance is examined as a function of a county excessive use factor, developed specifically for this study and based on various volume ranges and terrain as a proxy for sight distance. Four conclusions are supported: (1) there is no statistical difference in the safety performance of ultra-low-volume stop-controlled and uncontrolled intersections for all drivers or for younger and older drivers (although interestingly, older drivers are underrepresented at both types of intersections); (2) compliance with stop control (as indicated by crash performance) does not appear to be affected by the use or excessive use of STOP signs, even when adjusted for volume and a sight distance proxy; (3) crash performance does not appear to be improved by the liberal use of stop control; (4) safety performance of uncontrolled intersections appears to decline relative to stop-controlled intersections above about 150 daily entering vehicles. Subject to adequate sight distance, traffic professionals may wish to consider removal of control below this threshold. The report concludes with a section on methods and legal considerations for safe removal of stop control.

Selective ablation of photovoltaic materials with UV laser sources for monolithic interconnection of devices based on a-Si:H

Lasers are essential tools for cell isolation and monolithic interconnection in thin-film-silicon photovoltaic technologies. Laser ablation of transparent conductive oxides (TCOs), amorphous silicon structures and back contact removal are standard processes in industry for monolithic device interconnection. However, material ablation with minimum debris and small heat affected zone is one of the main difficulty is to achieve, to reduce costs and to improve device efficiency. In this paper we present recent results in laser ablation of photovoltaic materials using excimer and UV wavelengths of diode-pumped solid-state (DPSS) laser sources. We discuss results concerning UV ablation of different TCO and thin-film silicon (a-Si:H and nc-Si:H), focussing our study on ablation threshold measurements and process-quality assessment using advanced optical microscopy techniques. In that way we show the advantages of using UV wavelengths for minimizing the characteristic material thermal affection of laser irradiation in the ns regime at higher wavelengths. Additionally we include preliminary results of selective ablation of film on film structures irradiating from the film side (direct writing configuration) including the problem of selective ablation of ZnO films on a-Si:H layers. In that way we demonstrate the potential use of UV wavelengths of fully commercial laser sources as an alternative to standard backscribing process in device fabrication.

The role of embolic protection devices during carotid stenting prior to cardiac surgery in asymptomatic patients: Empty filters?

Objectives: The purpose of this study was to analyze the debris captured in the distal protection filters used during carotid artery stenting (CAS). Background: CAS is an option available to high-risk patients requiring revascularization. Filters are suggested for optimal stroke prevention during CAS. Methods: From May 2005 to June 2007, filters from 59 asymptomatic patients who underwent CAS were collected and sent to a specialized laboratory for light-microscope and histological analysis. Peri- and postprocedural outcomes were assessed during 1-year follow-up. Results: On the basis of biomedical imaging of the filter debris, the captured material could not be identified as embolized particles from the carotid plaque. On histological analysis the debris consisted mainly of red blood cell aggregates and/ or platelets, occasionally accompanied by granulocytes. We found no consistent histological evidence of embolized particles originating from atherosclerotic plaques. Post-procedure, three neurological events were reported: two (3.4%) transient ischemic attacks (TIA) and one (1.7%) ipsilateral minor stroke. Conclusion: The filters used during CAS in asymptomatic patients planned for cardiac surgery often remained empty. These findings may be explained by assuming that asymptomatic patients feature a different atherosclerotic plaque composition or stabilization through antiplatelet medication. Larger, randomized trials are clearly warranted, especially in the asymptomatic population. © 2012 Wiley Periodicals, Inc.

Remote Control of Mobile Devices in Android Platform

Remote control systems are a very useful element to control and monitor devices quickly and easily. This paper proposes a new architecture for remote control of Android mobile devices, analyzing the different alternatives and seeking the optimal solution in each case. Although the area of remote control, in case of mobile devices, has been little explored, it may provide important advantages for testing software and hardware developments in several real devices. It can also allow an efficient management of various devices of different types, perform forensic security tasks, etc ... The main idea behind the proposed architecture was the design of a system to be used as a platform which provides the services needed to perform remote control of mobile devices. As a result of this research, a proof of concept was implemented. An Android application running a group of server programs on the device, connected to the network or USB interface, depending on availability. This servers can be controlled through a small client written in Java and runnable both on desktop and web systems.

Computational and Energy Costs of Cryptographic Algorithms on Handheld Devices

Networks are evolving toward a ubiquitous model in which heterogeneousdevices are interconnected. Cryptographic algorithms are required for developing securitysolutions that protect network activity. However, the computational and energy limitationsof network devices jeopardize the actual implementation of such mechanisms. In thispaper, we perform a wide analysis on the expenses of launching symmetric and asymmetriccryptographic algorithms, hash chain functions, elliptic curves cryptography and pairingbased cryptography on personal agendas, and compare them with the costs of basic operatingsystem functions. Results show that although cryptographic power costs are high and suchoperations shall be restricted in time, they are not the main limiting factor of the autonomyof a device.

JXTA security in mobile constrained devices

JXME is the JXTA protocols implementation formobile devices using J2ME. Two different flavors of JXME have been implemented, each one specific for a particular set of devices, according to their capabilities. The main value of JXME is its simplicity to create peer-to-peer (P2P) applications in limited devices. In addition to assessing JXME functionalities, it is also important to realize the default security level provided. This paper presents a brief analysis of the current state of security in JXME, focusing on the JXME-Proxied version, identifies existing vulnerabilities and proposes further improvements in this field.

GTK+ toolkit on mobile Linux devices

Linux -käyttöjärjestelmä on laajasti käytössä palvelin- ja työpöytätietokoneissa. Linux on lisäämässä suosiotaan kuitenkin myös sulautetuissa laitteissa, kuten PDA:issa, kännyköissä sekä erilaisissateollisuusjärjestelmissä. Näytön koko, suorituskyky ja käytettävyys asettavat omia erityisiä tarpeitaan laitteiden graafiselle käyttöliittymälle. Linux -käyttöjärjestelmälle on olemassa useita käyttöliittymäkirjastoja, joista GTK+ on yksi yleisimmin käytetyistä. Tämä diplomityö esittelee sulautetun Linux -käyttöjärjestelmän ja GTK+ käyttöliittymäkirjaston, selvittäen miten hyvin ne soveltuvat mobiileihin päätelaitteisiin. Yksi suurimmista esteistä työpöytäkäyttöön suunnattujen teknologioiden, kuten GTK+, muokkaamisessa mobiileihin päätelaitteisiin on suorituskyky. Osana tätä työtä kehitettiin GtkPerf -niminen työkalu, jolla GTK+:n suorituskykyä eri alustoilla pystytään helposti mittaamaan ja havaitsemaan mahdollisia pullonkauloja. Tämän työn johtopäätöksenä on, että pienillä muokkailuilla ja optimoinneilla GTK+ soveltuu myös mobiileihin päätelaitteisiin. Ensimmäinen kaupallisesti saatavilla oleva GTK+ -pohjainen päätelaite, Nokia 770 Internet Tablet, on tästä osoituksena.

Prediction of hip fracture risk by quantitative ultrasound in more than 7000 Swiss women > or =70 years of age: comparison of three technologically different bone ultrasound devices in the SEMOF study.

To compare the prediction of hip fracture risk of several bone ultrasounds (QUS), 7062 Swiss women > or =70 years of age were measured with three QUSs (two of the heel, one of the phalanges). Heel QUSs were both predictive of hip fracture risk, whereas the phalanges QUS was not. INTRODUCTION: As the number of hip fracture is expected to increase during these next decades, it is important to develop strategies to detect subjects at risk. Quantitative bone ultrasound (QUS), an ionizing radiation-free method, which is transportable, could be interesting for this purpose. MATERIALS AND METHODS: The Swiss Evaluation of the Methods of Measurement of Osteoporotic Fracture Risk (SEMOF) study is a multicenter cohort study, which compared three QUSs for the assessment of hip fracture risk in a sample of 7609 elderly ambulatory women > or =70 years of age. Two QUSs measured the heel (Achilles+; GE-Lunar and Sahara; Hologic), and one measured the heel (DBM Sonic 1200; IGEA). The Cox proportional hazards regression was used to estimate the hazard of the first hip fracture, adjusted for age, BMI, and center, and the area under the ROC curves were calculated to compare the devices and their parameters. RESULTS: From the 7609 women who were included in the study, 7062 women 75.2 +/- 3.1 (SD) years of age were prospectively followed for 2.9 +/- 0.8 years. Eighty women reported a hip fracture. A decrease by 1 SD of the QUS variables corresponded to an increase of the hip fracture risk from 2.3 (95% CI, 1.7, 3.1) to 2.6 (95% CI, 1.9, 3.4) for the three variables of Achilles+ and from 2.2 (95% CI, 1.7, 3.0) to 2.4 (95% CI, 1.8, 3.2) for the three variables of Sahara. Risk gradients did not differ significantly among the variables of the two heel QUS devices. On the other hand, the phalanges QUS (DBM Sonic 1200) was not predictive of hip fracture risk, with an adjusted hazard risk of 1.2 (95% CI, 0.9, 1.5), even after reanalysis of the digitalized data and using different cut-off levels (1700 or 1570 m/s). CONCLUSIONS: In this elderly women population, heel QUS devices were both predictive of hip fracture risk, whereas the phalanges QUS device was not.

Suitability of Ultra Wideband for Mobile Devices

Mobiililaitteet ovat kehittyneet merkittävästi viimeisen vuosikymmenen aikana. Ne eivät enää ole pelkästään puhelimia tai kämmentietokoneita, vaan multimediatietokoneita, jotka pystyvät tuottamaan korkealaatuisia elämyksiä käyttäjälleen.Sisällön laadun paraneminen johtaa väistämättä myös siirrettävän tietomäärän kasvamiseen. Siksi uusia, nopeampia tiedonsiirtomenetelmiä on otettava käyttöön. Ultra Wideband (UWB) on uusi radioaaltotekniikka, jokamahdollistaa korkeat tiedonsiirtonopeudet lyhyillä etäisyyksillä. Tekniikka operoi erittäin leveällä 3.1 - 10.6 gigahertsin taajuuskaistalla.UWB on suunnattu nopeaan, langattomaan tiedonsiirtoon personal area networkin (PAN) laitteiden välillä. Tämän diplomityön tarkoituksena on arvioida UWBn soveltuvuutta mobiililaitteisiin. Arviointi tehdään teoreettiselta pohjalta, sillä UWBtä ei vielä ole implementoitu kaupallisiin laitteisiin. Ensin esitellään UWBn tekniikka ja ominaisuudet, jonka jälkeen sen soveltuvuutta arvioidaan esimerkkikäyttötapausten valossa. Esimerkkikäyttötapauksiksi on valittu kolme tyypillistä mutta erilaista toimintoa, jotka mahdollisimman hyvin kuvaavat mobiililaitteiden käyttöä.

Security in RFID devices

Aquest projecte inclou una aproximació als conceptes de RFID i targetes contactless centrant-se en l’ampliament usat MIFARE Classic chip. L’objectiu principal es mostrar el seu funcionament i les seves vulnerabilitats, així com alguns exemples pràctics fent una anàlisi de diferents serveis que les utilitzen.

Long-term continuous-flow left ventricular assist devices (LVAD) as bridge to heart transplantation.

Heart transplantation (HTx) is the treatment of choice for end-stage heart failure but the limited availability of heart's donors still represents a major issue. So long-term mechanical circulatory support (MCS) has been proposed as an alternative treatment option to assist patients scheduled on HTx waiting list bridging them for a variable time period to cardiac transplantation-the so-called bridge-to-transplantation (BTT) strategy. Nowadays approximately 90% of patients being considered for MCS receive a left ventricular assist device (LVAD). In fact, LVAD experienced several improvements in the last decade and the predominance of continuous-flow over pulsatile-flow technology has been evident since 2008. The aim of the present report is to give an overview of continuous-flow LVAD utilization in the specific setting of the BTT strategy taking into consideration the most representative articles of the scientific literature and focusing the attention on the evolution, clinical outcomes, relevant implications on the HTx strategy and future perspectives of the continuous-flow LVAD technology.

The synchronization of personal information between mobile devices and online services by using SyncML

Monet henkilökohtaiset mobiililaitteet tarjoavat mahdollisuuden tallentaa henkilötietoja ja mahdollisuuden lyhyen kantaman radiotekniikoiden hyödyntämiseen. Vastaavasti henkilötietoja käyttävien tai vaativien verkkopalveluiden määrä on kasvussa. Mobiililaitteisiin tallennetut henkilötiedot tarjoavat potentiaalisen keinon välttää samojen henkilötietojen toistuva käsinsyöttö erilaisiin verkkopalveluihin ja keskitettyyn ajantasallapitoon. Tässä työssä käydään läpi ratkaisumalli henkilökohtaisen mobiililaitteen ja verkkopalveluiden välillä tapahtuvaan henkilötietojen siirtoon ja synkronointiin. Malli pohjautuu selainlaajennukseen, joka voi pyytää sekä selaimessa auki olevalta verkkopalvelun sivulta että mobiililta päätelaitteelta senhetkiset henkilötiedot ja synkronoida ne. Jo olemassaolevia henkilötietojen hallintaa helpottavia ratkaisuja käydään läpi arvioiden käyttökelpoisuutta tämänkaltaisiin tarpeisiin. Ratkaisumallin kannalta olennaiset tekniikat ja standardit, erityisesti Bluetooth ja SyncML, esitellään. Ratkaisumallin arkkitehtuuri käydään korkealla tasolla läpi ja esitellään toteutuksen yksityiskohtia. Tuloksena on periaatteeltaan kelvollinen henkilökohtaisten tietojen synkronointijärjestelmä, jonka toteutusta nykyisten mobiilien päätelaitteiden toiminnallisuus jossain määrin hankaloittaa.

Adaptive Protocol Stacks for Mobile Devices

Tulevaisuudessa siirrettävät laitteet, kuten matkapuhelimet ja kämmenmikrot, pystyvät muodostamaan verkkoyhteyden käyttäen erilaisia yhteysmenetelmiä eri tilanteissa. Yhteysmenetelmillä on toisistaan poikkeavat viestintäominaisuudet mm. latenssin, kaistanleveyden, virhemäärän yms. suhteen. Langattomille yhteysmenetelmille on myös ominaista tietoliikenneyhteyden ominaisuuksien voimakas muuttuminen ympäristön suhteen. Parhaan suorituskyvyn ja käytettävyyden saavuttamiseksi, on siirrettävän laitteen pystyttävä mukautumaan käytettyyn viestintämenetelmään ja viestintäympäristössä tapahtuviin muutoksiin. Olennainen osa tietoliikenteessä ovat protokollapinot, jotka mahdollistavat tietoliikenneyhteyden järjestelmien välillä tarjoten verkkopalveluita päätelaitteen käyttäjäsovelluksille. Jotta protokollapinot pystyisivät mukautumaan tietyn viestintäympäristön ominaisuuksiin, on protokollapinon käyttäytymistä pystyttävä muuttamaan ajonaikaisesti. Perinteisesti protokollapinot ovat kuitenkin rakennettu muuttumattomiksi niin, että mukautuminen tässä laajuudessa on erittäin vaikeaa toteuttaa, ellei jopa mahdotonta. Tämä diplomityö käsittelee mukautuvien protokollapinojen rakentamista käyttäen komponenttipohjaista ohjelmistokehystä joka mahdollistaa protokollapinojen ajonaikaisen muuttamisen. Toteuttamalla esimerkkijärjestelmän, ja mittaamalla sen suorituskykyä vaihtelevassa tietoliikenneympäristössä, osoitamme, että mukautuvat protokollapinot ovat mahdollisia rakentaa ja ne tarjoavat merkittäviä etuja erityisesti tulevaisuuden siirrettävissä laitteissa.

The Total Deviation Index estimated by Tolerance Intervals to evaluate the concordance of measurement devices

Background In an agreement assay, it is of interest to evaluate the degree of agreement between the different methods (devices, instruments or observers) used to measure the same characteristic. We propose in this study a technical simplification for inference about the total deviation index (TDI) estimate to assess agreement between two devices of normally-distributed measurements and describe its utility to evaluate inter- and intra-rater agreement if more than one reading per subject is available for each device. Methods We propose to estimate the TDI by constructing a probability interval of the difference in paired measurements between devices, and thereafter, we derive a tolerance interval (TI) procedure as a natural way to make inferences about probability limit estimates. We also describe how the proposed method can be used to compute bounds of the coverage probability. Results The approach is illustrated in a real case example where the agreement between two instruments, a handle mercury sphygmomanometer device and an OMRON 711 automatic device, is assessed in a sample of 384 subjects where measures of systolic blood pressure were taken twice by each device. A simulation study procedure is implemented to evaluate and compare the accuracy of the approach to two already established methods, showing that the TI approximation produces accurate empirical confidence levels which are reasonably close to the nominal confidence level. Conclusions The method proposed is straightforward since the TDI estimate is derived directly from a probability interval of a normally-distributed variable in its original scale, without further transformations. Thereafter, a natural way of making inferences about this estimate is to derive the appropriate TI. Constructions of TI based on normal populations are implemented in most standard statistical packages, thus making it simpler for any practitioner to implement our proposal to assess agreement.

Context-based services for mobile devices

The subject of this master’s thesis was developing a context-based reminder service for mobile devices. Possible sources of context were identified and analyzed. One such source is geographical location obtained via a GPS receiver. These receivers consume a lot of power and techniques and algorithms for reducing power consumptions were proposed and analyzed. The service was implemented as an application on a series 60 mobile phone. The application requirements, user interface and architecture are presented. The end-user experiences are discussed and possible future development and research areas are presented.