980 resultados para Multi-stage Auctions
Resumo:
This paper is based on the novel use of a very high fidelity decimation filter chain for Electrocardiogram (ECG) signal acquisition and data conversion. The multiplier-free and multi-stage structure of the proposed filters lower the power dissipation while minimizing the circuit area which are crucial design constraints to the wireless noninvasive wearable health monitoring products due to the scarce operational resources in their electronic implementation. The decimation ratio of the presented filter is 128, working in tandem with a 1-bit 3rd order Sigma Delta (ΣΔ) modulator which achieves 0.04 dB passband ripples and -74 dB stopband attenuation. The work reported here investigates the non-linear phase effects of the proposed decimation filters on the ECG signal by carrying out a comparative study after phase correction. It concludes that the enhanced phase linearity is not crucial for ECG acquisition and data conversion applications since the signal distortion of the acquired signal, due to phase non-linearity, is insignificant for both original and phase compensated filters. To the best of the authors’ knowledge, being free of signal distortion is essential as this might lead to misdiagnosis as stated in the state of the art. This article demonstrates that with their minimal power consumption and minimal signal distortion features, the proposed decimation filters can effectively be employed in biosignal data processing units.
Resumo:
Network security monitoring remains a challenge. As global networks scale up, in terms of traffic, volume and speed, effective attribution of cyber attacks is increasingly difficult. The problem is compounded by a combination of other factors, including the architecture of the Internet, multi-stage attacks and increasing volumes of nonproductive traffic. This paper proposes to shift the focus of security monitoring from the source to the target. Simply put, resources devoted to detection and attribution should be redeployed to efficiently monitor for targeting and prevention of attacks. The effort of detection should aim to determine whether a node is under attack, and if so, effectively prevent the attack. This paper contributes by systematically reviewing the structural, operational and legal reasons underlying this argument, and presents empirical evidence to support a shift away from attribution to favour of a target-centric monitoring approach. A carefully deployed set of experiments are presented and a detailed analysis of the results is achieved.
Resumo:
Insbesondere bei Antriebssystemen stehen die Energiekosten neben den Anschaffungskosten im Fokus. Jedoch bleiben weitere Folgekosten, die im Laufe des Betriebs eines Antriebssystems in einem Fördermittel entstehen, meist unberücksichtigt. Dieser Artikel beschreibt einen Ansatz, wie sich Lebenszykluskosten von Antriebssystemen in Stetigfördertechnik prognostizieren lassen. Mit Hilfe von allgemein bekannten Normen und Richtlinien kann der Lebenszyklus eines Antriebssystems von der Projektierung über die Herstellung bis zur Entsorgung nach dem Betrieb in Kostenarten eingeteilt und veranschaulicht werden. Unter Verwendung von direkter Verrechnung als auch der Kalkulation mit Prozesskosten wird eine hinreichende Genauigkeit anhand definierter Prozessketten erreicht. Auf Basis dieser Kostenkalkulationen kann ein mehrstufiges Prognosemodell gebildet werden. Somit konnten durch das entwickelnde Modell Anlagenbeispiele untersucht und berechnet werden.
Resumo:
The aim of this thesis was threefold, firstly, to compare current player tracking technology in a single game of soccer. Secondly, to investigate the running requirements of elite women’s soccer, in particular the use and application of athlete tracking devices. Finally, how can game style be quantified and defined. Study One compared four different match analysis systems commonly used in both research and applied settings: video-based time-motion analysis, a semi-automated multiple camera based system, and two commercially available Global Positioning System (GPS) based player tracking systems at 1 Hertz (Hz) and 5 Hz respectively. A comparison was made between each of the systems when recording the same game. Total distance covered during the match for the four systems ranged from 10 830 ± 770 m (semi-automated multiple camera based system) to 9 510 ± 740m (video-based time-motion analysis). At running speeds categorised as high-intensity running (>15 km⋅h-1), the semi-automated multiple camera based system reported the highest distance of 2 650 ± 530 m with video-based time-motion analysis reporting the least amount of distance covered with 1 610 ± 370 m. At speeds considered to be sprinting (>20 km⋅h-1), the video-based time-motion analysis reported the highest value (420 ± 170 m) and 1 Hz GPS units the lowest value (230 ± 160 m). These results demonstrate there are differences in the determination of the absolute distances, and that comparison of results between match analysis systems should be made with caution. Currently, there is no criterion measure for these match analysis methods and as such it was not possible to determine if one system was more accurate than another. Study Two provided an opportunity to apply player-tracking technology (GPS) to measure activity profiles and determine the physical demands of Australian international level women soccer players. In four international women’s soccer games, data was collected on a total of 15 Australian women soccer players using a 5 Hz GPS based athlete tracking device. Results indicated that Australian women soccer players covered 9 140 ± 1 030 m during 90 min of play. The total distance covered by Australian women was less than the 10 300 m reportedly covered by female soccer players in the Danish First Division. However, there was no apparent difference in the estimated "#$%&', as measured by multi-stage shuttle tests, between these studies. This study suggests that contextual information, including the “game style” of both the team and opposition may influence physical performance in games. Study Three examined the effect the level of the opposition had on the physical output of Australian women soccer players. In total, 58 game files from 5 Hz athlete-tracking devices from 13 international matches were collected. These files were analysed to examine relationships between physical demands, represented by total distance covered, high intensity running (HIR) and distances covered sprinting, and the level of the opposition, as represented by the Fédération Internationale de Football Association (FIFA) ranking at the time of the match. Higher-ranking opponents elicited less high-speed running and greater low-speed activity compared to playing teams of similar or lower ranking. The results are important to coaches and practitioners in the preparation of players for international competition, and showed that the differing physical demands required were dependent on the level of the opponents. The results also highlighted the need for continued research in the area of integrating contextual information in team sports and demonstrated that soccer can be described as having dynamic and interactive systems. The influence of playing strategy, tactics and subsequently the overall game style was highlighted as playing a significant part in the physical demands of the players. Study Four explored the concept of game style in field sports such as soccer. The aim of this study was to provide an applied framework with suggested metrics for use by coaches, media, practitioners and sports scientists. Based on the findings of Studies 1- 3 and a systematic review of the relevant literature, a theoretical framework was developed to better understand how a team’s game style could be quantified. Soccer games can be broken into key moments of play, and for each of these moments we categorised metrics that provide insight to success or otherwise, to help quantify and measure different methods of playing styles. This study highlights that to date, there had been no clear definition of game style in team sports and as such a novel definition of game style is proposed that can be used by coaches, sport scientists, performance analysts, media and general public. Studies 1-3 outline four common methods of measuring the physical demands in soccer: video based time motion analysis, GPS at 1 Hz and at 5 Hz and semiautomated multiple camera based systems. As there are no semi-automated multiple camera based systems available in Australia, primarily due to cost and logistical reasons, GPS is widely accepted for use in team sports in tracking player movements in training and competition environments. This research identified that, although there are some limitations, GPS player-tracking technology may be a valuable tool in assessing running demands in soccer players and subsequently contribute to our understanding of game style. The results of the research undertaken also reinforce the differences between methods used to analyse player movement patterns in field sports such as soccer and demonstrate that the results from different systems such as GPS based athlete tracking devices and semi-automated multiple camera based systems cannot be used interchangeably. Indeed, the magnitude of measurement differences between methods suggests that significant measurement error is evident. This was apparent even when the same technologies are used which measure at different sampling rates, such as GPS systems using either 1 Hz or 5 Hz frequencies of measurement. It was also recognised that other factors influence how team sport athletes behave within an interactive system. These factors included the strength of the opposition and their style of play. In turn, these can impact the physical demands of players that change from game to game, and even within games depending on these contextual features. Finally, the concept of what is game style and how it might be measured was examined. Game style was defined as "the characteristic playing pattern demonstrated by a team during games. It will be regularly repeated in specific situational contexts such that measurement of variables reflecting game style will be relatively stable. Variables of importance are player and ball movements, interaction of players, and will generally involve elements of speed, time and space (location)".
Resumo:
This paper presents an investigation of a simple generic hyper-heuristic approach upon a set of widely used constructive heuristics (graph coloring heuristics) in timetabling. Within the hyperheuristic framework, a Tabu Search approach is employed to search for permutations of graph heuristics which are used for constructing timetables in exam and course timetabling problems. This underpins a multi-stage hyper-heuristic where the Tabu Search employs permutations upon a different number of graph heuristics in two stages. We study this graph-based hyper-heuristic approach within the context of exploring fundamental issues concerning the search space of the hyper-heuristic (the heuristic space) and the solution space. Such issues have not been addressed in other hyper-heuristic research. These approaches are tested on both exam and course benchmark timetabling problems and are compared with the fine-tuned bespoke state-of-the-art approaches. The results are within the range of the best results reported in the literature. The approach described here represents a significantly more generally applicable approach than the current state of the art in the literature. Future work will extend this hyper-heuristic framework by employing methodologies which are applicable on a wider range of timetabling and scheduling problems.
Resumo:
This paper presents an investigation of a simple generic hyper-heuristic approach upon a set of widely used constructive heuristics (graph coloring heuristics) in timetabling. Within the hyperheuristic framework, a Tabu Search approach is employed to search for permutations of graph heuristics which are used for constructing timetables in exam and course timetabling problems. This underpins a multi-stage hyper-heuristic where the Tabu Search employs permutations upon a different number of graph heuristics in two stages. We study this graph-based hyper-heuristic approach within the context of exploring fundamental issues concerning the search space of the hyper-heuristic (the heuristic space) and the solution space. Such issues have not been addressed in other hyper-heuristic research. These approaches are tested on both exam and course benchmark timetabling problems and are compared with the fine-tuned bespoke state-of-the-art approaches. The results are within the range of the best results reported in the literature. The approach described here represents a significantly more generally applicable approach than the current state of the art in the literature. Future work will extend this hyper-heuristic framework by employing methodologies which are applicable on a wider range of timetabling and scheduling problems.
Resumo:
Life Cycle Climate Performance (LCCP) is an evaluation method by which heating, ventilation, air conditioning and refrigeration systems can be evaluated for their global warming impact over the course of their complete life cycle. LCCP is more inclusive than previous metrics such as Total Equivalent Warming Impact. It is calculated as the sum of direct and indirect emissions generated over the lifetime of the system “from cradle to grave”. Direct emissions include all effects from the release of refrigerants into the atmosphere during the lifetime of the system. This includes annual leakage and losses during the disposal of the unit. The indirect emissions include emissions from the energy consumption during manufacturing process, lifetime operation, and disposal of the system. This thesis proposes a standardized approach to the use of LCCP and traceable data sources for all aspects of the calculation. An equation is proposed that unifies the efforts of previous researchers. Data sources are recommended for average values for all LCCP inputs. A residential heat pump sample problem is presented illustrating the methodology. The heat pump is evaluated at five U.S. locations in different climate zones. An excel tool was developed for residential heat pumps using the proposed method. The primary factor in the LCCP calculation is the energy consumption of the system. The effects of advanced vapor compression cycles are then investigated for heat pump applications. Advanced cycle options attempt to reduce the energy consumption in various ways. There are three categories of advanced cycle options: subcooling cycles, expansion loss recovery cycles and multi-stage cycles. The cycles selected for research are the suction line heat exchanger cycle, the expander cycle, the ejector cycle, and the vapor injection cycle. The cycles are modeled using Engineering Equation Solver and the results are applied to the LCCP methodology. The expander cycle, ejector cycle and vapor injection cycle are effective in reducing LCCP of a residential heat pump by 5.6%, 8.2% and 10.5%, respectively in Phoenix, AZ. The advanced cycles are evaluated with the use of low GWP refrigerants and are capable of reducing the LCCP of a residential heat by 13.7%, 16.3% and 18.6% using a refrigerant with a GWP of 10. To meet the U.S. Department of Energy’s goal of reducing residential energy use by 40% by 2025 with a proportional reduction in all other categories of residential energy consumption, a reduction in the energy consumption of a residential heat pump of 34.8% with a refrigerant GWP of 10 for Phoenix, AZ is necessary. A combination of advanced cycle, control options and low GWP refrigerants are necessary to meet this goal.
Resumo:
Background: The ubiquity of cell phones, which allow for short message service (SMS), provides new and innovative opportunities for disease prevention and health education. Objective: To explore the use of cell phone–based health education SMS to improve the health literacy of community residents in China. Methods: A multi-stage random sampling method was used to select representative study communities and participants ≥ 18 years old. Intervention participants were sent health education SMSs once a week for 1 year and controls were sent conventional, basic health education measures. Health literacy levels of the residents before and after the intervention were evaluated between intervention and control groups. Results: Public health literacy scores increased 1.5 points, from 61.8 to 63.3, after SMS intervention for 1 year (P<0.01); the increase was greater for males than females (2.01 vs. 1.03; P<0.01) and for Shenzhen local residents than non-permanent residents (2.56 vs. 1.14; P<0.01). The frequency of high health literacy scores was greater for the intervention than control group (22.03% to 30.93% vs. 22.07% to 20.82%). With health literacy as a cost-effective index, the cost-effectiveness per intervention was 0.54. Conclusion: SMS may be a useful tool for improving health literacy.
Resumo:
Racism continues to thrive on the Internet. Yet, little is known about racism in online settings and the potential consequences. The purpose of this study was to develop the Perceived Online Racism Scale (PORS), the first measure to assess people’s perceived online racism experiences as they interact with others and consume information on the Internet. Items were developed through a multi-stage process based on literature review, focus-groups, and qualitative data collection. Based on a racially diverse large-scale sample (N = 1023), exploratory and confirmatory factor analyses provided support for a 30-item bifactor model with the following three factors: (a) 14-item PORS-IP (personal experiences of racism in online interactions), (b) 5-item PORS-V (observations of other racial/ethnic minorities being offended), and (c) 11-item PORS-I (consumption of online contents and information denigrating racial/ethnic minorities and highlighting racial injustice in society). Initial construct validity examinations suggest that PORS is significantly linked to psychological distress.
Resumo:
Background: The prevalence of obesity is increasing among Iranian youngsters like other developing countries. Objectives: This study was conducted to assess regional disparities in sedentary behaviors and meal frequency in Iranian adolescents. Patients and Methods: In this national survey, 5682 students aged 10 - 18 years from urban and rural districts of 27 provinces of Iran were selected via stratified multi-stage sampling method. The country was classified into four sub-national regions, based on criteria of the combination of geography and socioeconomic status (SES). Mean of meal frequency and physical activity levels as well as prevalence of omitting meals and sedentary behavior were compared across regions with different SES after stratifying with sex and age group. Results: Meal frequency in lower socio-economic regions was significantly higher than two other regions in 10 - 13 and 10 - 18 years old groups (P trend < 0.001). However, the mean of working hours with computer was linearly increased with increasing the SES in studied regions (P trend < 0.001), whereas the corresponding figure was not significant for the mean of watching TV (P trend > 0.05). Frequency of adolescents omitting their meals was higher in higher SES regions especially in West Iran (P < 0.001) in 10 - 13 years old age group. Having personal computer and working with it more than two hours per day mainly was observed in central Iran which ranked as the highest SES group. Conclusions: Efforts to ensure Iranian youth meet healthy food habits and screen time guidelines include limiting access to screen technologies and encouraging parents to monitor their own screen time is required.
Resumo:
The objective of reservoir engineering is to manage fields of oil production in order to maximize the production of hydrocarbons according to economic and physical restrictions. The deciding of a production strategy is a complex activity involving several variables in the process. Thus, a smart system, which assists in the optimization of the options for developing of the field, is very useful in day-to-day of reservoir engineers. This paper proposes the development of an intelligent system to aid decision making, regarding the optimization of strategies of production in oil fields. The intelligence of this system will be implemented through the use of the technique of reinforcement learning, which is presented as a powerful tool in problems of multi-stage decision. The proposed system will allow the specialist to obtain, in time, a great alternative (or near-optimal) for the development of an oil field known
Development of new scenario decomposition techniques for linear and nonlinear stochastic programming
Resumo:
Une approche classique pour traiter les problèmes d’optimisation avec incertitude à deux- et multi-étapes est d’utiliser l’analyse par scénario. Pour ce faire, l’incertitude de certaines données du problème est modélisée par vecteurs aléatoires avec des supports finis spécifiques aux étapes. Chacune de ces réalisations représente un scénario. En utilisant des scénarios, il est possible d’étudier des versions plus simples (sous-problèmes) du problème original. Comme technique de décomposition par scénario, l’algorithme de recouvrement progressif est une des méthodes les plus populaires pour résoudre les problèmes de programmation stochastique multi-étapes. Malgré la décomposition complète par scénario, l’efficacité de la méthode du recouvrement progressif est très sensible à certains aspects pratiques, tels que le choix du paramètre de pénalisation et la manipulation du terme quadratique dans la fonction objectif du lagrangien augmenté. Pour le choix du paramètre de pénalisation, nous examinons quelques-unes des méthodes populaires, et nous proposons une nouvelle stratégie adaptive qui vise à mieux suivre le processus de l’algorithme. Des expériences numériques sur des exemples de problèmes stochastiques linéaires multi-étapes suggèrent que la plupart des techniques existantes peuvent présenter une convergence prématurée à une solution sous-optimale ou converger vers la solution optimale, mais avec un taux très lent. En revanche, la nouvelle stratégie paraît robuste et efficace. Elle a convergé vers l’optimalité dans toutes nos expériences et a été la plus rapide dans la plupart des cas. Pour la question de la manipulation du terme quadratique, nous faisons une revue des techniques existantes et nous proposons l’idée de remplacer le terme quadratique par un terme linéaire. Bien que qu’il nous reste encore à tester notre méthode, nous avons l’intuition qu’elle réduira certaines difficultés numériques et théoriques de la méthode de recouvrement progressif.
Development of new scenario decomposition techniques for linear and nonlinear stochastic programming
Resumo:
Une approche classique pour traiter les problèmes d’optimisation avec incertitude à deux- et multi-étapes est d’utiliser l’analyse par scénario. Pour ce faire, l’incertitude de certaines données du problème est modélisée par vecteurs aléatoires avec des supports finis spécifiques aux étapes. Chacune de ces réalisations représente un scénario. En utilisant des scénarios, il est possible d’étudier des versions plus simples (sous-problèmes) du problème original. Comme technique de décomposition par scénario, l’algorithme de recouvrement progressif est une des méthodes les plus populaires pour résoudre les problèmes de programmation stochastique multi-étapes. Malgré la décomposition complète par scénario, l’efficacité de la méthode du recouvrement progressif est très sensible à certains aspects pratiques, tels que le choix du paramètre de pénalisation et la manipulation du terme quadratique dans la fonction objectif du lagrangien augmenté. Pour le choix du paramètre de pénalisation, nous examinons quelques-unes des méthodes populaires, et nous proposons une nouvelle stratégie adaptive qui vise à mieux suivre le processus de l’algorithme. Des expériences numériques sur des exemples de problèmes stochastiques linéaires multi-étapes suggèrent que la plupart des techniques existantes peuvent présenter une convergence prématurée à une solution sous-optimale ou converger vers la solution optimale, mais avec un taux très lent. En revanche, la nouvelle stratégie paraît robuste et efficace. Elle a convergé vers l’optimalité dans toutes nos expériences et a été la plus rapide dans la plupart des cas. Pour la question de la manipulation du terme quadratique, nous faisons une revue des techniques existantes et nous proposons l’idée de remplacer le terme quadratique par un terme linéaire. Bien que qu’il nous reste encore à tester notre méthode, nous avons l’intuition qu’elle réduira certaines difficultés numériques et théoriques de la méthode de recouvrement progressif.
Resumo:
SPECT-1 y -2 y SIAP-1 y -2 son proteínas pertenecientes al esporozoíto de Plasmodium falciparum causante de la malaria más agresiva en los humanos. Estas proteínas están involucradas en el paso del parásito a través de las células del hospedero humano y en la invasión del hepatocito, haciéndolas blancos atractivos para ser estudiadas. Péptidos conservados de alta capacidad de unión (cHABPs) a células HeLa y HepG2 derivados de estas moléculas son no inmunogénicos porque son incapaces de generar una respuesta inmunitaria, pero son claves para el parásito porque cumplen una función importante durante la infección del hospedero humano. En este trabajo se encontró que algunos cHABPs pertenecientes a las proteínas SPECT-1 y -2, están posiblemente involucrados con la unión y formación de poros sobre la membrana de las células hospederas, ayudando al esporozoíto a abrirse paso través de las células del hospedero. Por otro lado, con el fin de cambiar el comportamiento inmunológico de cHABPs derivados de SPECT-1 y -2 y SIAP-1 y -2, se obtuvieron nuevos péptidos mediante el reemplazo de aminoácidos críticos por otros residuos cuya masa molecular sea similar, pero diferente en su polaridad. En este trabajo se reporta que dichas modificaciones promovieron cambios en la estructura secundaria (determinada por DC o 1H-RMN) de los péptidos modificados (mHABPs) cuando se comparó con la estructura de los cHABPs nativos; adicionalmente, estos mHABPs invirtieron su comportamiento inmunológico convirtiéndose en péptidos inmunogénicos inductores de anticuerpos. Lo que permite establecer la existencia de una relación entre la estructura que adoptan estos mHABPs con su actividad inmunológica. Además, algunos de los mHABPs estudiados aquí, pueden ser candidatos a ser incluidos en la vacuna contra la malaria químicamente sintetizada multi-epitope y multi-estadio que se está desarrollando en la Fundación Instituto de Inmunología de Colombia (FIDIC).
Resumo:
In this Thesis a series of numerical models for the evaluation of the seasonal performance of reversible air-to-water heat pump systems coupled to residential and non-residential buildings are presented. The exploitation of the energy saving potential linked to the adoption of heat pumps is a hard task for designers due to the influence on their energy performance of several factors, like the external climate variability, the heat pump modulation capacity, the system control strategy and the hydronic loop configuration. The aim of this work is to study in detail all these aspects. In the first part of this Thesis a series of models which use a temperature class approach for the prediction of the seasonal performance of reversible air source heat pumps are shown. An innovative methodology for the calculation of the seasonal performance of an air-to-water heat pump has been proposed as an extension of the procedure reported by the European standard EN 14825. This methodology can be applied not only to air-to-water single-stage heat pumps (On-off HPs) but also to multi-stage (MSHPs) and inverter-driven units (IDHPs). In the second part, dynamic simulation has been used with the aim to optimize the control systems of the heat pump and of the HVAC plant. A series of dynamic models, developed by means of TRNSYS, are presented to study the behavior of On-off HPs, MSHPs and IDHPs. The main goal of these dynamic simulations is to show the influence of the heat pump control strategies and of the lay-out of the hydronic loop used to couple the heat pump to the emitters on the seasonal performance of the system. A particular focus is given to the modeling of the energy losses linked to on-off cycling.