Modelagem em 3D de uma patela humana e análise de esforços utilizando o método dos elementos finitos

Throughout the history of medicine surgeons realized the importance of the patella to the functioning of the knee. The main function of the patella is to increase the mechanical efficiency of the quadriceps tendon and knee extensor mechanism. It was found that 50% to 80% of the fractures without deviation of the patella have the transversal pattern, possibly due to excessive tensile forces applied to the extensor mechanism. The purpose of this study is to analyze the loads to which a patella is submitted during a normal extension movement of knee. This analysis will be done by modeling a 3D patella and subsequent load simulation as, described in medical literature, using the finite element method

Análise de falhas por fadiga de alto ciclo em eixos de transmissão utilizando o método dos elementos finitos

This work presents a study that aims to validate the fatigue analyses developed on finite element commercial software, ANSYS Workbench. It was based on mechanical tests development of traction and hardness, to verify the mechanical properties of material that the shaft was manufactured (ABNT 1045 steel), it was developed bend test, with purpose to prove the confiability degree of computational analyses, obtaining the maximum stress in a work condition determined with 40 [kgf] of load applied, and at the end, was developed the fatigue test to obtain the number of cycles that the transmission shaft can support in a work condition with 8 [kgf] of load applied. The results obtained during the work present, have to be quite satisfactory with the theoretically expected

Concentração de tensões em peças e componentes estruturais - uma abordagem através do método dos elementos finitos

Any failure process that may occur in a part probably is located where the stress exceeded the level of resistance. When a part or component has a sharp change in geometry, such as slots, holes, grooves, bumps or other irregularities, there is an increased concentration of stress at a specific location of the part. The objective of this study is to determine the maximum stresses in structural parts and components using the equations of elasticity theory in conjunction with the stress concentration factor experiment and compare them with results obtained by finite element method

Análise estrutural de treliças espaciais no software Excel utilizando o médodo dos elementos finitos

The following paper means to develop a program to make structural analysis of space trusses. The program to be implemented was based on the concepts of the finite element method and used the programing resources of Visual Basic for Applications (VBA) for the Excel Software®. Being Excel® a software of easy access, low cost, capacity to make matrix calculations and with advanced resources of VBA programing, it is possible to develop an economic solution, efficient and precise for structural analysis of space trusses. Firstly is presented a finite elemento method and the space truss. Then is developed a few important algorithms to be used during the development of the program and also the use of a few resources of VBA. And to validate the quality, efficiency and precision of the results, these are compared with the established commercial software Ansys

Análise de fadiga em rodas automotivas utilizando método dos elementos finitos

The increasing search for better performance at the automotive industry, especially on the matter of fuel consumption, caused a progressive evolution of industrial technology. For the wheel this study is based on the try of reducing mass and decreasing the moment of inertia, characteristics that directly reflect on the performance parameter, as consumption and acceleration, so that it also is effective on the growth of the profit margin, since it reduces the costs of the locomotion. In this paper will be applied the Finite Element Analysis to explain the wheel behavior and identify ways to improve the performance. To the analyze it will be simulated a test condition established by ABNT NBR 6751:2009 foreseeing a possible collapse through general yielding and fatigue. The load here presented results from the equation presented on the norms and in the datas provided by the manufacturer

Estudo de tensões residuais em juntas soldadas utilizando o método dos elementos finitos

Pós-graduação em Engenharia Mecânica - FEG

Influência de diferentes superfícies de implantes unitários com geometria do tipo hexágono externo, Platform Switching e Cone-Morse em osso tipo III e IV: estudo pelo método dos elementos finitos tridimensionais

Pós-graduação em Odontologia - FOA

Análise das tensões em próteses implantossuportadas esplintadas, variando a localização dos implantes, pôntico e cantilever: estudo pelo método dos elementos finitos tridimensionais

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise comparativa de tensões e deformações específicas em uma estrutura treliçada, utilizando abordagem experimental e pelo método de elementos finitos

The process of knowledge construction is associated with physical or mechanical view of the phenomenon. In mechanical engineering courses should supplement their courses with physical or virtual learning devices to aid visualization of these phenomena. For the purpose of improving the mechanical engineering department laboratory practice was developed, through a project, a didactic device a trellis. The purpose of this work is the detailed study by comparing the theoretical results with the experimental results collected through the specific strains collected in the Catman. The study was iniatially done with nodes made of aluminum, giving results with high errors not allowing a good conclusion of results. For best results were achieved an improvement of the structure with strict we support the lattice and, thus, further study and greater quality of lattice structure

Caracterização do fator de intensidade de tensão em corpos trincados através do método dos elementos finitos

The industry generally has sought materials with high mechanical resistance, low density, thermal stability and corrosion resistance. In the aerospace industry, for example, the use of aluminum alloys, such as Al 2024-T351 and Al 7075-T7351, have become essential. However, the use of these materials often do not resulted in a satisfactory performance of the component, since the presence of cracks can cause total rupture of the component, even with a tension below the yield stress of the material, unexpectedly. In this work, these aluminum alloys were analyzed and samples were modeled by the finite element method. Moreover, in the models were applied two different types of cracks, central and edge crack, a vertical force was applied to result in a tension 70% of the yield stress of the material analyzed. Through stress asymptotic distribution in the region near the crack tip were calculated the values of the stress intensity factors for each crack length, after the stress intensity factors characterized were compared graphically with the values of fracture toughness found in the available literature

Influência do desenho do implante na micromovimentação de implantes imediatos com carga imediata: análise multivariada em elementos finitos

The purpose of this paper was to evaluate the influence of different implant designs on the micromovements of immediately placed implants. CT-based finite element models comprising an upper central incisor socket and four commercially available internal connection implant designs (SIN SW®, 3i Certain®, Nobel ReplaceTM, and RN synOcta® ITI Standard) of comparable diameter and length were constructed. 50, 100 and 200N magnitude loads were applied over the implant. ANOVA at 95% level of significance was used to evaluate bone to implant relative displacement (micromovements). The implant design (68,80%) greatly influences the micromovement of immediately placed implants. However, the loading magnitude (68,80%) is the most important factor regarding the implant stability in this protocol.

Solução das equações de Navier-Stokes e da equação de transporte por um método de elementos finitos estabilizado pela técnica de separação baseada na característica

Pós-graduação em Engenharia Mecânica - FEIS

Análise de falhas por fadiga num rotor de hidrogerador vertical via método dos elementos finitos

Pós-graduação em Engenharia Mecânica - FEG

Projeto estrutural de um conector bipartido utilizado na indústria de óleo & gás através do método dos elementos finitos

Pós-graduação em Engenharia Mecânica - FEG

Análise das tensões em próteses implantossuportadas esplintadas, variando o tipo de conexão protética e a inclinação do implante: estudo pelo método dos elementos finitos tridimensionais não linear

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)