Effect of processing route on the phase formation and properties of Bi4Ti3O12 ceramics

Our efforts were directed to the preparation of bismuth titanate-Bi4Ti3O12 (BIT) by two procedures: mechanically assisted synthesis and polymeric precursor method to display a variety of their advantages. To follow the nucleation and phase formation of BIT, XRD and Rietveld refinement analysis were used and it was shown that Bi4Ti3O12 ceramic can been successfully prepared from nano-sized powders obtained by both methods. The ferroelectric properties were determined and the loops from BIT obtained by polymeric precursor method were not fully saturated with a remnant polarization of 20 mu C/cm(2) and coercitive field of 1500 kV/cm. BIT obtained from powders prepared by mechanically assisted synthesis shows a remnant polarization of 0.65 mu C/cm(2) and coercitive field of 1050 kV/cm. The grain morphology may be the factor causing the observed differences. (C) 2005 Published by Elsevier Ltd and Techna Group S.r.l.

Dynamics of Tm-Ho energy transfer and deactivation of the F-3(4) low level of thulium in fluorozirconate glasses

The mechanism involved in the Tm3+ (F-3(4))-->Ho3+ (I-5(7)) energy transfer and Tm3+ (H-3(4), H-3(6))-->Tm3+ (F-3(4), F-3(4)) cross relaxation as a function of the donor and acceptor concentrations was investigated in Tm-Ho-codoped fluorozirconate glasses. The experimental transfer rates were determined for the Tm-->Ho energy transfer from the best fit of the acceptor luminescence decay using an expression which takes into account the Inokuti-Hirayama model and localized donor-to-acceptor interaction solution. The original acceptor solution derived from the Inokuti-Hirayama model fits well the acceptor luminescence transient only for low-concentrated systems. The results showed that a fast excitation diffusion that occurs in a very short time (t<of donors as an average of the microscopic rate equation solution of each D-*-A pair separated by distance R that contributes in addition to the Inokuti-Hirayama solution. The observation that the experimental transfer rates were always much bigger than the one predicted by the diffusion model, in which the energy transfer process is assisted by excitation migration among donors state, reinforces the existence of a fast excitation diffusion among donor ions before the energy transfer to acceptor already observed in Yb:Er:ZBLAN. The fast excitation diffusion effect was observed to dominate both the Tm-->Tm cross relaxation and Tm-->Ho energy transfer ions from H-3(4) and F-3(4) thulium states, respectively. (C) 2004 American Institute of Physics.

Influence of processing conditions on the thermal decomposition of SrTiO3 precursors

The present work investigates the influence of milling and calcination atmosphere on the thermal decomposition of SrTiO3 powder precursors. Both pure and neodymium-modified SrTiO3 samples were studied. Milling did not significantly influence numerical mass loss value, but reduced the number of decomposition steps, modifying the profiles of the TG and DTA curves. on the other hand, milling increases the amount of energy liberated by the system upon combustion of organic matter. It was also observed that the milling process, associated to the calcination in an oxygen atmosphere, considerably decreases the amount of organic matter and increases the final mass loss temperature.

Effect of root canal filling material and level of surgical injury on periodontal healing in dogs

Some divergencies in the literature about periodontal healing after surgical injury stimulated the development of this experiment. The root canals of dogs' teeth were negotiated and filled by the lateral condensation technique with two kinds of sealers: Sealapex and zinc oxide-eugenol cement. In the second session, the bone tissue was exposed and one cavity was made at the apical third of the root and another at the border between the coronal and middle thirds, both penetrating into the root canal. Six months later the animals were sacrificed and the specimens prepared for histopathologic analysis. The results showed that the kind of filling material and the level of the periodontal wound exposing the root canal can influence the healing process (P<0.01).

Effects of processing on the structure of zein/oleic acid films investigated by X-ray diffraction

Zein films plasticized with oleic acid were formed by solution casting, by the stretching of moldable resins, and by blown film extrusion. The effects of the forming process on film structure were investigated by X-ray diffraction. Wide-angle X-ray scattering (WAXS) patterns showed d-spacings at 4.5 and 10 angstrom, which were attributed to the zein alpha-helix backbone and inter-helix packing, respectively. The 4.5.angstrom d-spacing remained stable under processing while the 10 angstrom d-spacing varied with processing treatment. Small-angle X-ray scattering (SAXS) detected a long-range periodicity for the formed films but not for unprocessed zein, which suggests that the forming process-promoted film structure development is possibly aided by oleic acid. The SAXS d-spacing varied among the samples (130-238 angstrom) according to zein origin and film-forming method. X-ray scattering data suggest that the zein molecular structure resists processing but the zein supramolecular arrangements in the formed films are dependent on processing methods.

Synthesis, structural refinement and optical behavior of CaTiO3 powders: A comparative study of processing in different furnaces

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Effect of processing conditions on the nucleation and growth of indium-tin-oxide nanowires made by pulsed laser ablation

Indium-tin oxide nanowires were deposited by excimer laser ablation onto catalyst-free oxidized silicon substrates at a low temperature of 500 degrees C in a nitrogen atmosphere. The nanowires have branches with spheres at the tips, indicating a vapor-liquid-solid (VLS) growth. The deposition time and pressure have a strong influence on the areal density and length of the nanowires. At the earlier stages of growth, lower pressures promote a larger number of nucleation centers. With the increase in deposition time, both the number and length of the wires increase up to an areal density of about 70 wires/mu m(2). After this point all the material arriving at the substrate is used for lengthening the existing wires and their branches. The nanowires present the single-crystalline cubic bixbyite structure of indium oxide, oriented in the [100] direction. These structures have potential applications in electrical and optical nanoscale devices.

Architecture of the caudal vena cava wall of the dog at the level of the liver caudate lobe

The vascular segment of the caudal vena cava of the dog at the level of the caudate lobe was shown to be intimately related to hepatic tissue through the hepatic capsule and parenchyma. The tunica adventitia of the caudal vena cava was formed mainly by smooth muscle cells with collagen and elastic fibers arranged in bundles. The thin tunica media of the vein was also formed by smooth muscle cells, collagen and elastic fibers arranged in bundles. The tunica intima presented an elastic sub-endothelial network. The hepatic segment of the caudal vena cava showed a myoconnective architecture and propulsive characteristics in terms of its hemodynamic pattern.

Yield and fruit size distribution of processing tomato cultivars

The productivity and fruit size distribution of 28 processing tomato cultivars were analyzed to determine the ones with potential for fresh market. The experiment was done in Jaboticabal-SP, Brazil (21o15'22'' South, 48o18'58'' West, altitude 595 m), in a Haplorthox soil, from June to December. The cultivars H 7155, Hypeel 108, Andino, U 573, H 9036, Ipa 6, H 9494, AG 33, Yuba, RPT 1294, AG 72, Peelmech, Curicó, Hypeel 45, RPT 1478, H 9492, H 9498, H 2710, Hitech 45, Halley, Botu 13, H 9553, U 646, NK 1570, AG 45, RPT 1095, RPT 1570 and PSX 37511 were evaluated. The experimental design was randomized blocks, with four repetitions, and five plants per experimental unit. Fruits harvested from each experimental unit were counted, classified by transversal diameter (large, medium, small, very small and cull) and then weighed. Cultivars AG 72, H 9498, Hypeel 45, RPT 1095 and Curicó yielded more than 70 fruits per plant, on average. The total production per plant of cultivars AG 72, H 9498, Hypeel 45, H 7155, Hypeel 108, Halley, Hitech, RPT 1095, H 9494, H 9036 and Curicó was greater than 4 kg. Considering the weight of large and medium fruits, categories which are important for fresh market, the cultivars H 2710, Botu 13, U 573, Hypeel 45, Yuba, RPT 1294 and Ipa 6 presented values above 50% for production.

Total and harvest-date yield of processing tomato cultivars

The productivity of 28 tomato cultivars was evaluated over three stages of harvest. The study was carried out during from June to December of 1999 in an open field at the experimental area of the Section of Olericulture and Aromatic Medicinal Plants, Department of Crop Production at FCAV-UNESP, Jaboticabal, SP, Brazil. The cultivars studied were H 7155, Hypeel, Andino, U 573, H 9036, IPA 6, H 9494, AG 33, Yuba, RPT 1294, AG 72, Pelmeech, Curico, Hypeel 45, RPT 1478, H 9492, H 9498, H 2710, Hitech 45, Halley, Botu 13, H 9553, U 646, NK 1570, AG 45, RPT 1095, RPT 1570, and PSX 37511. The experimental design was a randomized block design with four repetitions, with five plants per plot. Productivity was evaluated at three stages of harvest at 119, 149 and 179 days after seeding. There were no significant differences among the cultivars at the first harvest (119 days). The majority of the cultivars produced their highest yield at the second harvest; the most productive cultivars were Curicó and AG 72, which yielded 4.69 and 4.67 kg/plant, respectively, although they did not differ statistically from the cultivars Hypeel 45 (4.35 kg/plant) and H 9498 (4.16 kg/plant). Yields of the cultivars Andino and H 9494 were evenly distributed between the second and third harvests. At the third harvest, cultivar IPA 6 had the highest yield (2.9 kg/plant) and was statistically different from all other cultivars except H 9036 (2.34 kg). These two cultivars had the most delayed and concentrated maturity, making them suitable for mechanical harvesting, although at a later time. Cultivar AG 72 had the greatest total yield (5.76 kg/plant), but it was not statistically different from cultivars Hypeel 45 (5.43 kg), Curico (4.17 kg), H 9498 (4.83 kg), H 7155 (4.58 kg) and Halley (4.55 kg). All of the cultivars, with the exception of cultivars H 9036, IPA 6, Andino and H 9494 showed in the second harvest concentrated maturity, making it suitable for mechanical harvesting.

Physical-chemical characterization of processing tomato fruit

Fruit of 28 tomato cultivars for industrial processing were characterized to identify cultivars with potential for in natura consumption. The experiment was carried out in Jaboticabal-SP, Brazil (21o15'22'' South, 48o18'58'' West, altitude 595 m), on a Haplorthox soil during June-December. The cultivars used in this study were: H 7155, Hypeel 108, Andino, U 573, H 9036, Ipa 6, H 9494, AG 33, Yuba, RPT 1294, AG 72, Peelmech, Curicó, Hypeel 45, RPT 1478, H 9492, H 9498, H 2710, Hitech 45, Halley, Botu 13, H 9553, U 646, NK 1570, AG 45, RPT 1095, RPT 1570 and PSX 37511. The experimental design was randomized blocks, replicated four times. Ten fruits per plot were analyzed, evaluating the following characteristics: shape (oblong or round); length and diameter (mm); external and internal coloration; presence of fissures; number of loci; pulp thickness (mm); soluble solids content (Brix) and total acidity. Only cultivars Hypeel 108, AG 72, NK 1570, RPT 1570 had oblong fruit. Cultivars which had pulp thicker than 5.5 mm, a characteristic which is directly related to fruit yield for industrial purposes were: Ipa 6, Andino, U 646, H 9553, RPT 1294 and Hypeel 108. Cultivars Ipa 6 and Andino also presented elevated values for length, diameter and pulp thickness, indicating them as quality material for industry or, alternatively, for in natura market. Among the cultivars which presented better values for acidity (higher or equal to 0.3 g citric acid 100 g-1) were RPT 1095, AG 45, H 9553 and Hypeel 45.

Level of insight and clinical features of obsessive-compulsive disorder with and without body dysmorphic disorder

Introduction: Body dysmorphic disorder (BDD) and obsessive-compulsive disorder (OCD) have several similarities and are included among the obsessive-compulsive spectrum of disorders. However, the content of preoccupations and level of insight of BDD patients differ from OCD patients. Objective: To compare the level of insight regarding obsessive-compulsive symptoms (OCS) and other clinical features in OCD patients with and without comorbid BDD. Methods: We evaluated 103 OCD patients (n=25, comorbid BDD), according to Diagnostic and Statistical Manual of Mental Disorders, Fourth Edition criteria using the Structured Clinical Interview for DSM-IV, the Yale-Brown Obsessive-Compulsive Scale, the University of Sao Paulo Sensory Phenomena Scale, the Beck Depression and Anxiety Inventories, and the Brown Assessment of Beliefs Scale. Resylts: The study groups differed significantly on several clinical features, including level of insight. A worse level of insight regarding OCS was independently associated with the presence of comorbid BDD. Lower educational level, more psychiatric comorbidities, presence of somatic and hoarding obsessions, and presence of intrusive images were associated with BDD comorbidity, even after adjusting for possible confounders. Conclusion: The presence of BDD in OCD patients is associated with poorer insight into obsessional beliefs and higher morbidity, reflected by lower educational levels and higher number of psychiatric comorbid disorders in general.

Influence of the power level of an ultra-sonic system on dental cavity preparation

The aim of this study was to evaluate the shape of dental cavities made with the CVDentus® system using different ultrasound power levels. One standard cavity was made on the buccal aspect of 15 bovine incisors with a CVDentus® cylindrical bur (82142). The sample was divided into three groups: G1 - ultrasound with power II; G2 - ultrasound with power III; and G3 - ultrasound with power IV. A standardizing device was used to obtain standardized preparations and ultrasound was applied during one minute in each dental preparation. The cavities were sectioned in the middle, allowing observation of the cavity's profile with a magnifying glass, and width and depth measurement using the Leica Qwin program. The Kruskal-Wallis (p < 0.05) and Dunn statistical analyses demonstrated differences between the dental cavity shapes when powers III and IV were used. However, the cavities that were made with power III presented dimensions similar to those of the bur used for preparation. We concluded that the power recommended by the manufacturer (III) is the most adequate for use with the CVDentus® system.

Reproduction, food dynamics and exploitation level of Oreochromis niloticus (Perciformes: Cichlidae) from artisanal fisheries in Barra Bonita Reservoir, Brazil

Nile tilapia (Oreochromis niloticus), which is exotic to South America, is the most common species caught in artisanal fisheries at the Barra Bonita Reservoir, Southeastern Brazil. This species is of great socioeconomic importance for the region and keeps active a population of about 500 fishers. In the present study we assess reproduction, food dynamics and level of exploitation of O. niloticus, caught by artisanal fisheries in the Barra Bonita Reservoir. Specimens were collected monthly, from July 2004-June 2005, and a total of 1 715 specimens were analyzed. Each specimen was examined to obtain biological and biometric data: standard length (cm), total weight (g), reproductive data (sex and stage of maturation), and stomach contents (empty, partly full, and full). We also estimated the sex ratio (by macroscopic observation of gonads), reproductive period (by ovarian development and seasonal average of gonadosomatic index in females), and feeding habits (by stomach contents). The possible relationship between abiotic factors and the reproductive period was statistically verified using Spearman's Rank Correlation. The FiSAT (ELEFAN I) package was used to assess growth parameters, mortality rates and to infer exploitation rate from standard length frequencies. The O. niloticus population had a sex ratio of 1.3:1 (M:F). Results indicated that ripe females were captured throughout the year, with a higher frequency during the winter-2004 (with a frequency of 59%, at a mean temperature of 20.5°C), and in spring-2004 (with a frequency of 60.5% at a mean temperature of 21.18°C). The GSI mean values obtained by season were: winter-2004: 1.71; spring-2004: 1.72; summer-2005: 0.80, and autumn-2005: 1.19. The Spearman correlation indicated positive values with respect to pH, dissolved oxygen, electric conductivity, transparency and chlorophyll a, and negative values with respect to temperature, accumulated rainfall and altimetric benchmark. The main food items were phytoplankton and periphytic algae, observed in 99.6% of the analyzed stomachs. The estimated growth and mortality parameters were: L∞=33.60cm, k=0.63/year, longevity= 4.76years, Z=2.81/ year, M=1.20/year and F=1.61/year. The weight-length relationship was Ln Wt=-2.8532+2.8835 Ln Lp. The estimated yield per recruit values were as follows: E=0.570, Emax=0.776, E0.1=0.604 and E0.5=0.349. These results indicate that a well established population of O. niloticus is present at Barra Bonita Reservoir; with an active reproduction throughout the year, more intense during winter and spring, and that O. niloticus is a phytoplanktophagus species. There were no indications that this species is being overfished, we therefore recommend that, due to its exotic condition, no restrictions need to be taken on its fishing activities.