Is the OECD acute worm toxicity test environmentally relevant? The effect of mineral form on calculated lead toxicity

In a series of experiments the toxicity of lead to worms in soil was determined following the draft OECD earthworm reproduction toxicity protocol except that lead was added as solid lead nitrate, carbonate and sulphide rather than as lead nitrate solution as would normally be the case. The compounds were added to the test soil to give lead concentrations of 625-12500 pg Pb g-1 of soil. Calculated toxicities of the lead decreased in the order nitrate > carbonate > sulphide, the same order as the decrease in the solubility of the metal compounds used. The 7-day LC50 (lethal concentration when 50% of the population is killed) for the nitrate was 5321 +/- 275 mug Pb g(-1) of soil and this did not change with time. The LC50 values for carbonate and sulphide could not be determined at the concentration ranges used. The only parameter sensitive enough to distinguish the toxicities of the three compounds was cocoon (egg) production. The EC50S for cocoon production (the concentration to produce a 50% reduction in cocoon production) were 993, 8604 and 10 246 mug Pb g(-1) of soil for lead nitrate, carbonate and sulphide, respectively. Standard toxicity tests need to take into account the form in which the contaminant is present in the soil to be of environmental relevance. (C) 2002 Elsevier Science Ltd. All rights reserved.

Characterization of mineral surfaces using FIB and TEM: a case study of naturally weathered alkali feldspars

Using a focused ion beam (FIB) instrument, electron-transparent samples (termed foils) have been cut from the naturally weathered surfaces of perthitic alkali feldspars recovered from soils overlying the Shap granite, northwest England. Characterization of these foils by transmission electron microscopy (TEM) has enabled determination of the crystallinity and chemical composition of near-surface regions of the feldspar and an assessment of the influence of intragranular microtextures on the microtopography of grain surfaces and development of etch pits. Damage accompanying implantation of the 30 kV Ga+ ions used for imaging and deposition of protective platinum prior to ion milling creates amorphous layers beneath outer grain surfaces, but can be overcome by coating grains with > 85 nm of gold before FIB work. The sidewalls of the foil and feldspar surrounding original voids are also partially amorphized during later stages of ion milling. No evidence was found for the presence of amorphous or crystalline weathering products or amorphous "leached layers" immediately beneath outer grain surfaces. The absence of a leached layer indicates that chemical weathering of feldspar in the Shap soils is stoichiometric, or if non-stoichiometric, either the layer is too thin to resolve by the TEM techniques used (i.e., <=similar to 2.5 nm) or an insufficient proportion of ions have been leached from near-surface regions so that feldspar crystallinity is maintained. No evidence was found for any difference in the mechanisms of weathering where a microbial filament rests on the feldspar surface. Sub-micrometer-sized steps on the grain surface have formed where subgrains and exsolution lamellae have influenced the propagation of fractures during physical weathering, whereas finer scale corrugations form due to compositional or strain-related differences in dissolution rates of albite platelets and enclosing tweed orthoclase. With progressive weathering, etch pits that initiated at the grain surface extend into grain interiors as etch tubes by exploiting preexisting networks of nanopores that formed during the igneous history of the grain. The combination of FIB and TEM techniques is an especially powerful way of exploring mechanisms of weathering within the "internal zone" beneath outer grain surfaces, but results must be interpreted with caution owing to the ease with which artifacts can be created by the high-energy ion and electron beams used in the preparation and characterization of the foils.

A concise summary of the International System of Units, the SI

The Bureau International des Poids et Mesures, the BIPM, was established by Article 1 of the Convention du Mètre, on 20 May 1875, and is charged with providing the basis for a single, coherent system of measurements to be used throughout the world. The decimal metric system, dating from the time of the French Revolution, was based on the metre and the kilogram. Under the terms of the 1875 Convention, new international prototypes of the metre and kilogram were made and formally adopted by the first Conférence Générale des Poids et Mesures (CGPM) in 1889. Over time this system developed, so that it now includes seven base units. In 1960 it was decided at the 11th CGPM that it should be called the Système International d’Unités, the SI (in English: the International System of Units). The SI is not static but evolves to match the world’s increasingly demanding requirements for measurements at all levels of precision and in all areas of science, technology, and human endeavour. This document is a summary of the SI Brochure, a publication of the BIPM which is a statement of the current status of the SI. The seven base units of the SI, listed in Table 1, provide the reference used to define all the measurement units of the International System. As science advances, and methods of measurement are refined, their definitions have to be revised. The more accurate the measurements, the greater the care required in the realization of the units of measurement.

How a sequential design would have affected the GAIN international study of Gavestinel in stroke

While planning the GAIN International Study of gavestinel in acute stroke, a sequential triangular test was proposed but not implemented. Before the trial commenced it was agreed to evaluate the sequential design retrospectively to evaluate the differences in the resulting analyses, trial durations and sample sizes in order to assess the potential of sequential procedures for future stroke trials. This paper presents four sequential reconstructions of the GAIN study made under various scenarios. For the data as observed, the sequential design would have reduced the trial sample size by 234 patients and shortened its duration by 3 or 4 months. Had the study not achieved a recruitment rate that far exceeded expectation, the advantages of the sequential design would have been much greater. Sequential designs appear to be an attractive option for trials in stroke. Copyright 2004 S. Karger AG, Basel

Life histories of music service histories, the past in inductees' present

This article discusses inductee music service teachers (to 25 years of age). It explores how their lives, as perceived, shape current identities in teaching and result in several career problems. Respondents were drawn from a comprehensive life history study of 28 Local Education Authority employees. Of this larger cohort, four were age 25 years and below, and the remaining 24 teachers made retrospective comments. Data were collected and analysed between October 2002 and March 2004. Principal findings suggest that schooling failed to address these educators' needs as musical learners; key childhood experiences were external of schools. This often resulted in an idealistic trajectory, in teenage years, towards an occupation as a performer. An occupation in music education was entirely disregarded. Consequently, inductees now consider training experiences an inappropriate platform for their professional lives. Managing group teaching and children's behaviour engenders considerable anxiety. Music service work is also deemed a transient state of affairs. There are implications for training, retention and professional development.